Search Documents

By Ted Klemetti

Roof deterioration in weak moisture-sensitive rock leads to roof falls in coal mines. An observation site was set up in intake air at an underground coal mine in central Ohio to evaluate the time-dependent deterioration of moisture-sensitive roof rock. By periodically collecting and weighing the rock falling from the roof, the National Institute for Occupational Safety and Health (NIOSH) was able to quantify the deterioration of the moisture-sensitive shale roof. The measurements showed that more roof rock is falling in the dry winter months. Movements in an intersection were monitored in order to determine if deformation correlated with seasonal changes in temperature and humidity. The rate of intersection roof-to-floor convergence was found to be cyclical and related to seasonal changes, with more convergence during the months of April through September. At the study site intersection, the roof beam did not show deflection indicating movement most likely due to mine floor deformation. The bolt load also increased in the warmer months before shedding load, possibly due to rock failure. Temperature and relative humidity sensors, placed in holes in the roof show that mine air does not mix with the air in the holes. Consistent saturation levels of relative humidity were measured in the holes and it appears that high levels of moisture may have migrated into the bolt holes from roof shales. A roof sealant applied to a portion of the test roof appears to be preserving the roof and reducing the amount of rock fall into the entry, while the screened area virtually eliminated rock falling from the roof.

Jan 1, 2009

By M. P. Nesterov

The method of predicting the time-dependent surface subsidence for gently-inclined potash deposits where total extraction using various sizes of yielding bamier pillars was discussed.

Jan 1, 1998

By Alan Peacock

Shield supports have been in use in the USA underground mines since 1975, and their development in the intervening time has been progressive and inovative. Specialized techniques are used to optimize their performance in a particular application and to design the component parts.

Jan 1, 1981

By Kelvin K. Wu

A coal waste disposal dam failed on Buffalo Creek near Saunders, West Virginia, on February 26, 1972. This accident resulted in the loss of 125 lives, left over 4000 people homeless, and resulted in millions of dollars in damage to several downstream communities. As a result of this tragic event, major changes occurred in the mine waste disposal practices used by the U.S. coal industry. This paper summarizes changes in U.S. coal-waste disposal practices in the nearly 35 years since the Buffalo Creek dam failure and identifies safety issues that need to be addressed for continued improvement. While many organizations and individuals have played roles in the improvements that have occurred, this paper focuses on the role played by MSHA and its predecessor agencies.

Jan 1, 2006

By Axel Preusse

On the basis of the Law on Financing Hard Coal Mining dated 28 December 2007, the subsidized German hard coal mining industry will be shut down to the end of the year 2018 in a socially acceptable manner; in 2012 this decision will be reassessed. Even after the abandonment of all mining activities subsequent burdens are inevitable. In this paper, the possible long-term effects resulting from a mining industry history, which is spanning more than 200 years, and their possible consequences are pointed out, in particular in connection with the abandonment of mine water drainage measures which is economically meaningful in the long term. According to the decision situation as it presents itself today, this point in time will be far beyond 2018. In preparation for this, an action framework is to be developed in areas possibly affected.

Jan 1, 2008

By D. Su

This paper presents the details and results of a preliminary investigation into the response of borehole pressure cells (BPCs) in soft coal. Two parallel approaches, laboratory calibration and nonlinear finite element simulation, were adopted for deter- mining the BPC K-factor, which was defined as the ratio of cell pressure change to the corresponding change in external pressure. Results from both the laboratory calibration and the nonlinear finite element simulation revealed a nonlinear response of cell internal fluid pressure to external loading. The K-fact& also is shown to increase with increasing setting pressure and decreasing medium modulus. -Depending on the setting pressure, the K-factor for coal having a Young's modulus of 1.6 x lo5 psi ranges from nearly 1.2 at 2,000 psi of external pressure to 1.485 at 8,400 psi of external pressure. The improved under- standing of BPC behavior leads to the more accurate calculation of BPC K-factor in coal which significantly improves the correlation between pillar pressures measured in underground coal mines and those predicted by nonlinear finite element simulations of these pillars.

Jan 1, 1990

By Yi Luo

The efforts to mitigate longwall subsidence influences on various residential and farming structures by many coal mining companies have been successful in the recent years (Luo, et al, 2003). The successes were largely dependent on the accurate subsidence predictions, correct assessments of potential influences, appropriate design and implementation of the mitigation measures. However, such efforts for protecting large industrial structures are still very rare. In this paper, the successful assessment and mitigation of the subsidence influences associated with a very intensive dynamic longwall subsidence process on a large workshop are presented.

Jan 1, 2005

By James Arthur

In deep coal mining the support of the underground roadway is fundamental and without knowledge of the mechanics of ground control a mine is unlikely to be operating safely and efficiently. It is therefore important for the support system to be designed sat¬isfactorily for the size of the excavation required and to do so an understanding of the behaviour of the surrounding strata is re¬quired. Over the last 15 years there has been a major change in the industry and the support systems adopted. The industry has been privatised, legislation has been updated, a comprehensive research programme has been carried out and guidance docu¬ments produced. The paper will show how privatisation has not allowed support standards to deteriorate, highlight research, the legislation and guidance documents updated and how this has led to a reduction in accidents and falls of ground..

Jan 1, 2002

By Klaus Opolony

The world's most popular method of longwall mining requires multiple entry systems for the panels. In contrast to this mine layout the roadways in German coal mining are used for advanced mining from the rock mechanic point of view or are even re-used by a second panel. This procedure of roadway use is presented within this paper using a 3D visualisation software tool. In the previous conferences in Morgantown several papas had addressed the basics of rock mechanic background, planning tools and variants. This paper gives a practical case study for reuse of a roadway in a German coal mine. The heading and the use of various alternatives are compared under the aspect of efficiency and costs. Within the comparison the specific requirements and benchmarks of German coal mines are taken into consideration. The costs for a multiple entry system and first of all the development rates that can be achieved with common road heading systems are compared with international layout alternatives. A prospect includes a discussion of pro and con for various development methods. Devices are given due to this prospect if and how multiple entry systems are applicable to German coal mines. The paper gives an initial point for international comparison and is a base for further discussion.

Jan 1, 2003

By Erdal Unal

In underground mining today, safety and economical aspects demand a better understanding of the rock-mass conditions, particularly for design of underground mine openings excavated in weak and stratified rock mass. The rock mass classification systems, in essence, are empirical approaches utilized during preliminary design stage. These systems have been developed for specific purposes and rock mass types, therefore, direct utilization of the classification systems in their original form, for characterization of complex rock-mass conditions is not always possible. This is probably one of the main reasons why designers continue to originate new systems, or modify and extend the ones already existing. RMR and Q systems, for example, although widely used in mining and tunnelling, can not fully describe the specifications of the weak, stratified and flay bearing rock mass. Consequently, the engineering applications that would be carried out based on original RMR and Q ratings could be inadequate for making design decisions even during the preliminary design stage.

Jan 1, 1990

By Thomas M. Barczak

The engineering of a support system is driven largely by economics. The goal is to provide effective support at minimal cost. For this reason, wood has been extensively used as a support material for centuries. The cost of timber for mining applications has risen by more than 50% in the past 5 years and is likely to continue to increase as the supply diminishes and further environmental restrictions are placed on timber harvesting. The increased cost and lack of high strength wood in the Western United States has provided incentives to improve the utilization of wood and to develop alternative support materials. This U.S. Bureau of Mines' (USBM) report discusses the basic engineering requirements for the application of various materials for supplemental roof support construction and provides an overview of support systems that use materials other than wood. A comparison of support performance and cost for various material constructions is made to assist the mine operator in support selection. The scope of materials discussed in the report include: (1) conventional mine timber loaded perpendicular to the grain, (2) parallel to the grain timber loading, (3) steel fiber reinforced and air entrained concrete, (4) steel, (5) granular fill materials, and (6) combinations of these as composite support structures. The range of support systems analyzed include wood and concrete cribs, concrete columns and props, steel beams, friction props, and several novel support concepts.

Jan 1, 1994

By Madan M. Singh

Mining under bodies of water such as oceans, lakes, rivers, streams, ponds, and other impoundments, is not a new technique. However, in the United States it has been fairly restricted to date. In order to recover the maximum amount of the nation's reserves, in the future, it is important that further mining under such bodies of water be planned. However, it is imperative that this is not done at the expense of danger to the nation's miners or appreciable property damage. If all the bodies of water are considered large, and it is assumed that these constitute a hazard when mining in their vicinity irrespective of their size and geometry, a significant percentage of the coal reserves are likely to be sterilized. How- ever, by adopting special mining plans and procedures, it may be possible to release reserves for exploitation that would otherwise be unmineable since the surface of bodies of water below which they lie are relatively small in size. In 1977, the Bureau of Mines issued Information Circular (IC) 8741, entitled "Results of Research to Develop Guidelines for Mining Near Surface and Underground Bodies of Water". This document was based on the work done by Skelly and Loy (under Contract No. H0252083) and K. Wardell and Partners (under Contract No. H0252021). How ever, these guidelines have limited application, because these did not (1) define the bodies of water of concern, and (2) take into account the nature of the strata being encountered. These guidelines assumed that all bodies of water which would be undermined were large. For the purposes of this discussion, water bodies may be divided into three categories, depending upon their potential to cause damage to the underlying mining activity: ? catastrophic ? major ? limited Bodies of water which pose the threat of catastrophic destruction in the mine, should there be an inrush, include oceans, large lakes, big inland reservoirs, and rivers that could flood the mine complete- ly in a short period. Those with major potential for damage would include lakes and streams which might present a danger to both life and property if not considered in the mining plans. Finite bodies of water which have a volume considerably smaller than the mine volume offer a limited potential for damage in the case of an inrush. These include flowing streams which have a relatively small rate of replenishment and which can be dealt with by pumping or isolation in the event of a breakthrough into the mine. Such bodies of water may be inconvenient and cause a temporary disruption of production, and could even cause some damage to equipment, but only in rare instances would personal injuries occur. The scope of this paper is limited to the exploitation of stratified mineral deposits with overlying -face bodies of water. Vein and dessiminate ore deposits are not discussed, nor are breakthroughs into adjacent mines in the same horizon. Overlying, water-logged strata also pose a serious threat to mining, but are not treated in this discussion. Pending further investigation these strata may be considered as bodies of water with catastrophic potential for damage, with the base of the strata being considered the bottom of the water body. When the body of water is large, so that it may cause catastrophic damage to the mine in the event of an inrush, the guidelines suggested in IC 8741 are applicable. In order to develop criteria and procedures for mining under smaller bodies of water, however, it is necessary that the nature of the strata disturbance due to underground mining be examined.

Jan 1, 1981

By Rodger Fry

All coal deposits contain anomalous geologic conditions which have an impact on roof control, Run-Of--Mine (ROM) coal quality and production costs. To remain competitive in today's coal market and provide a safe working atmosphere, mine operators need to know in advance of mining the geologic conditions which prevail in the coal deposit. In order to identify geologic anomalies within a coal seam and surrounding roof rock in advance of mining, the Radio Imaging Method (RIM) survey procedure has been developed. This paper describes the RIM procedure and how it is used to predict various geologic conditions within a coal deposit. Figure 1 illustrates the RIM in-mine and surface surveys which can be used in an underground mine. [ ] RIM is an electromagnetic (EM} wave process which consists of in-mine and surface survey techniques. Both techniques are used in underground coal mines to detect faults, interbedding, sandstone channels, and thinning coal. Thesurface survey can also be used to determine seam correlation and continuity in strip and underground mining. In-mine and surface surveys work by propagating EM waves along straight paths through the coal. As the RIM signal travels along a ray path, it interacts with the seam material and surrounding rock. This interaction causes the signal to lose energy thereby decreasing its strength along the path. The amount of energy loss per unit path length depends upon the coal seam height and type of surrounding roof and floor rock. A reading of the signal level is taken at the end of the ray path at the receiver location. This reading is used to determine the loss (attenuation) rate of the signal along the path. The signal level data is compiled and analyzed through computerized algorithms which construct images of any anomaly present. This graphical depiction of the coal provides a basis for further geologic interpretation. By comparing the images reconstructed by the RIM analysis to in-mine geologic mappings made while mining through RIM study zones, it has been confirmed that RIM can help detect the following; Rapidly Thinning Coal Incompetent Roof Rock Poor Floor Lithology

Jan 1, 1984

By Murali M. Gadde

Perimeter mining is a special form of very productive partial extraction method practiced at some mines in the United States. In the Illinois Basin mines where all major coal seams have weak underclay in the immediate floor, experience shows that any long-term ground control issues will arise due to floor failures rather than instability of the coal pillar itself. While there is a significant amount of work done on floor stability associated with regular pillars, no work has been done so far on the stability of perimeter pillars. This paper reports the results of a comprehensive study that was conducted for the first time on floor stability during perimeter mining in the Illinois Basin mines. A special plate template, which mimicked a common perimeter pillar configuration was created to conduct in-situ bearing capacity tests at five mines in three states of the Basin. Additionally, because of the complex shape of pillars created in perimeter mining that defies any closed-form solution, floor bearing capacity was studied using three-dimensional nonlinear numerical modeling. Based on these in-situ and numerical studies, some guidelines are provided for perimeter pillar stability analysis.

Jan 1, 2009

By R. Kaund

"Quantifying the rockburst consequence is of critical importance to reduce the hazards with preventative measures in underground mines and deep tunnels. Contours of energy components within a pillar model are plotted at different rockmass damage stages, and plastic strain work and released energy are proposed as indicators of rockmass damage consequence. One pillar model under different loading stiffness is simulated to assess indicators of pillar burst and the resulting damages. The results show the rockmass damage under soft loading stiffness has larger magnitude of plastic strain work and released energy than that which is under stiff loading stiffness, indicating the rockburst consequence can be quantified with plastic strain work and released energy in numerical models. With the quantified rockburst consequence, preventative measures can be taken to avoid severe hazards to mine safety.INTRODUCTIONWith the increasing demand of mineral resources and depletion of near-surface ores, the depths of underground mines have made the mining activities one of mankind’s most dangerous types of work (Ortlepp, 2005). The Mine Safety and Health Administration (MSHA) defines rockburst as “a sudden and violent failure of overstressed rock resulting in the instantaneous release of large amounts of accumulated energy.”The types of rockburst can be classified into three types: (1) strain burst, (2) pillar burst, and (3) fault slip (Müller, 1991). Strain burst is the most common type of unstable rock failure in underground openings, where the intensity and scale are usually smaller than pillar burst and fault slip (White and Whyatt, 1999; White, Williams and Whyatt, 2002; Ortlepp, 2005). The cause of strain burst can range from shattering of rock under high stress concentration to buckling of discontinuities parallel to underground openings. The occurrence of pillar burst also depends on the stress and discontinuity conditions in the rockmass, but pillar burst usually involves the sudden loss of strength in the core or foundation of a pillar (Whyatt and Blake, 2002; Kias and Ozbay, 2013; Khademian et al., 2016). Fault slip or slip burst can be either slip along pre-existing discontinuities or shear failure in the rockmass, when the shear stress is larger than shear strength in the fault (Rice, 1983; White and Whyatt, 1999; Sainoki and Mitri, 2014). The consequence of fault slip can vary from very small rockmass damage to consequential rockmass damage, but large seismic magnitude does not always result in large rockmass damage (White and Whyatt, 1999; Whyatt and Blake, 2002)."

Jan 1, 2018

By Keith Heasley

As part of the initial investigation and validation of a new boundary-clement formulation for stress modeling in coal mines. the underground stresses and displacements at two multiple-seam coal mines with unique stress problems are modeled and predicted. The new program, LAMODEL, calculates stresses and displacements at the seam level and at requested locations in the overburden or at the surface. Both linear elastic and non-linear seam materials can he used: and surface effects, multiple seams, and multiple mining steps can be simulated. In order to most efficiently use LAMODEL for accurate stress prediction, the program is first calibrated to the site-specific geo-mechanics based on previously observed stress conditions at the mine. For this calibration process. a previously mined area is "stress mapped" by quantifying the observed pillar and strata behavior using a numerical rating system. Then, the site-specific mechanical properties in the model are adjusted to provide the best correlation between the predicted stresses and the observed underground stress rating. Once calibrated, the model is then used to predict future stress problems abead of mining. At the two case study mines, the calibrated models showed good correlation with the observed stresses, and also accurately predicted upcoming high stress areas for preventive action by the mines.

Jan 1, 1998

By Gary Buchan

"Mine-wide ground control stability is essential to any mining operation to prevent catastrophic failure of underground structures. The ability to recognize or indicate the potential for ground control hazards in underground mine operations is highly desirable to reduce or eliminate ground-control-related injuries and fatalities. The acoustic emissions (AE) form of non-destructive testing has been used for decades to determine material or machine deterioration or potential failure. This paper presents the findings of research in AE with the results of laboratory bolt pull tests and comparisons to field experimentation, including AE sensors and bolt load data in an underground stone mine. The goal of the project is to compare laboratory results of AE sensors on roof bolt pull tests with field experimentation to determine the capability of predicting bolt failure or roof deterioration.INTRODUCTIONMine-wide ground control stability is essential to any mining operation to prevent catastrophic failure of underground structures. The ability to recognize or indicate the potential for ground control hazards in underground mining operations is highly desirable to reduce or eliminate ground-control-related injuries and fatalities. Typical ground control monitoring devices involve drilling into roof or rib, grouting or gluing of sensors, and dedicated cabling for data collection. One of the original goals of this research was to develop a methodology for a simple wireless device that could provide an indication or warning of potential roof bolt or roof failure. Various types of nondestructive testing (NDT) have been used for decades to determine material or machine deterioration or the potential failure of either. One type of NDT is acoustic emission (AE) monitoring, which has been studied for use in mining to predict rock bursts and mine failures since the 1940s (Obert, 1941; Obert and Duvall, 1942). The primary goal of the work was to compare laboratory results of AE sensors on roof bolt pull tests with field experimentation to determine the capability of evaluating bolt loading or roof deterioration in an underground stone mine. Bolt pull tests were conducted in the laboratory to establish a repeatable trend of AE activity versus bolt load. The second part of the project was to then install bolt load cells in an underground stone mine and monitor AE activity in the vicinity of mining."

Jan 1, 2018

By Jennifer Riefenberg

Research efforts by the U.S. Bureau of Mines include running a series of displacement-discontinuity, boundary-element models to simulate the gateroad design at an underground coal mine in northwestern Colorado. The initial mine design is a yield-abutment chain pillar arrangement in a three-entry, longwall gateroad system. Pressure effects from mining the first and second panel were recorded using borehole pressure cells (BPCs). These field data were then compared directly to the model output. Observed yielding in the field was approximated by reducing material property values and/or removing pillar elements in the model. Model results using this calibration technique mirrored the field measurements consistently. Using the calibrated model parameters, a suite of models was run simulating an experimental entry design: exchanging the yield and abutment pillar locations. These model results reflect a 20¬to 33-percent reduction in core stresses in the yield pillar during mining of the second panel. Improved pillar and entry conditions are suggested by these predictive results. The design modifications were then implemented at the mine along a 150-m (500-ft) test section. Field observations and measurements from the experimental design test site compared favorably with trends of the model predictions.

Jan 1, 1993

By Samrat Mohanty

The construction of underground hydrocarbon storage caverns in Jurong Island, Singapore, is nearing completion. The facility, located beneath the seabed of Banyan Basin, is comprised of five storage caverns with a storage capacity of approximately 1.5 million cubic meters. The galleries of each cavern are 20 m wide by 27 m high and approximately 340 m long. In addition to the storage caverns, various access and operations tunnels are required to support the facility. Among these are water curtain galleries to ensure that hydrostatic pressures in excess of hydrocarbon storage pressure are maintained in the rock mass surrounding the storage caverns. Early in the design process, conventional steel rock bolts with resin polymer grout were considered for ground control. However, the construction contractor proposed using fibe-reinforced polymer (FRP) bolts with cement grout due to the corrosive hydrologic environment, weight and handling considerations, local construction preferences, and the requirement to have a cavern design life of 50 years. FRP bolts with cement grout were ultimately chosen for the project. The FRP bolting system has proven to be very successful, with no ground failures experienced where systematic FRP bolting has been applied. This paper discusses the properties of FRP bolt/cement grout bolting systems, their characteristics in relation to steel bolt/resin bolting systems, and numerical modeling results assessing their performance.

Jan 1, 2014

In this paper, the plastic increment theory was applied in a 2-D finite element model, and a generalized Von Mises yielding criterion adopted to simulate the progressive failure of coal pillars. Extensive underground monitoring was conducted and the data compared with the computer model, yielding promising results. Three different longwall entry layouts, including a stable (s-s) pillar system, a yield-stable-yield (y-s-y) pillar system and a yield (y-y) pillar system, were investigated using the model developed. The yield-stable-yield system was considered to be the best of the designs studied in the case. A comprehensive parametric analysis was also performed. The triaxial factor and Poisson's ratio were found to be the most important material parameters affecting pillar yielding.

Jan 1, 1988