Search Documents

By John D. VandeKraats

Yielding rock bolt systems have been developed to provide ground support while accommodating shifting, creeping, or swelling ground movements. The Dywidag Systems, Inc. (DSI) Slip Nut System is one such system. It has been tested in the laboratory and installed and monitored in the interbedded halite and anhydrite at the Waste Isolation Pilot Plant (WIPP) since 1994. The Slip Nut System is installed on a point anchored threaded bar or on a threaded bar coupled to a cable bolt. At a pre-engineered load the nut acts as a die and cuts through the thread on which it rests, thereby reducing the load and coming to rest on the next thread where the process repeats. Two types of laboratory tests were performed using slip nuts on DSI's threaded bars and their Tensionable Cable bolts. Straight pull tests exceeding 0.3m (1 ft.) of displacement were performed on the systems. Also, offset tests were performed on these bolt systems in a test frame designed to simulate WIPP geologic conditions. A room scale test area consisting of 186 threaded bars began in 1994. Select bolts were instrumented to track bolt load. All bolts were tracked through time for operation. Through three complete years since installation over twelve slips, corresponding to approximately 0.15m (6 in.) of ground movement, have been observed in some areas. Since installation strata offset has exceeded 0.08m (3 in.) at a supported clay layer in the roof. No bolt failures have been observed. Slip loads observed underground generally approximate those observed in the lab. To date, the slip nut systems tested and installed have performed as expected.

Jan 1, 1998

By Weidong Pan, Yinchao Yang, Baodong Zuo

Fully mechanized mining technology, with a large cutting height in thick coal seam, has been developed to be large-scale, mechanized, and intelligent. Furthermore, it is also superior to other mining methods because it operates more efficiently and has higher recovery rates of coal resources. Dongpang coal mine (located in north China) is one of the largest coal mining productions in Hebei province. It is significant because it is the first set of coal mines in China to adopt fully mechanized mining technology that has large cutting height potential. When looking at the coal seams of deep mining, specifically in the mine No. 2612 where the working face is 4.5–6.5 m cutting height, the coal walls have low stability due to the way the coal seam fluctuates in a large working face. This paper adopts mechanical analysis, numerical simulation, and field observation research methods to control the rib fall of coal walls in a coal mine. By adopting research methods that analyze the mechanical characteristics of face roof, we are able to conclude the main roof structure of the masonry seam stability criterion in overhead mining with large cutting height. This is done through employing the numerical simulation method, which helped to determine the main factors that influence the rib fall of a coal wall and weighting factor. Through field observations, we discovered the technology method to relieve, control, and mitigate rib falls of coal seam in a coal mine. We also discovered methods that would ensure the smooth mining of the working face of the mine by strengthening the bolting and grouting reinforcement methods used to improve the working face of stope surrounding rock conditions. This paper discusses research results that enrich the stope wall rock control method by expressing how fully mechanized mining technology, with a large cutting height, is meaningful to solve the complex conditions of rock fall caused by thick coal seam.

Jan 1, 2017

By Dennis R. Barratt

Rockbolting is now used extensively as a method of primary support in UK coalmines. Over the past fifteen years an optimum bolting system has evolved, based on a high grade steel bolt and a very strong stiff resin. Where necessary, cablebolts are used in conjunction with rockbolts as a supplementary means of support. The rockbolting system, as currently used, is based on a maximum bolt length of 2.4 m whilst cablebolts are generally 6 or 8 m long. Based on the UK experience, there are situations where it is necessary to extend the bolted horizon above that normally achieved with a 2.4 m long rockbolt. Until recently the only options available were coupled rockbolts or cablebolts, both of which have inherent problems in terms of installation. Flexible Strand Rockbolts (FSR), in lengths of 4 to 6 m, provide the means of being able to extend the normal bolted horizon Other advantages include increased strength characteristics (tensile and shear), able to be installed in the UK standard hole size (26-28 mm), encapsulation using resin capsules, thus offering immediate support, high bond strength compared to conventional strand, and able to be installed using existing drilling and bolting equipment. The FSR is considered to be a new concept in terms of strata control and one that compliments the rockbolting system currently in use.

Jan 1, 1997

By Madan M. Singh

Currently longwall coal mining operations require at least 3 entries on both the headgate and tailgate ends because of ventilation and safety requirements. Driving of entries, however, is a slow and costly process. Often it is a bottleneck in longwall development. Single entry gateroads are permitted in Europe and commonly used there. This study entailed ascertaining the feasibility of using a single entry in the United States, without sacrificing safety. This design was conducted for an operating longwall mine in the Black Warrior coalfield in Alabama, An understanding of rock loads and consequent support requirements is prerequisite to the design and successful demonstration of the single entry system. Efforts in this regard were directed at determining center (packwall) support requirements for various single entry widths. Critical to the analysis is knowledge of the nature and extent of side abutment stresses. In collecting geological and geotechnical information relating to the stability of the single entry, Engineers International, Inc. engaged in the following: ? Examination and inspection of the single entry demonstration at the Sunnyside Mine in Utah. Severe ground conditions and unacceptable levels of entry closure were experienced there prior to the tailgate phase. Observations at the mine presented a clear perspective on possible ground control problems for future single entry designs. ? Reconnaissance inspection and classification of roof rock conditions. ? Detailed mapping of roof structure in the areas to be instrumented. ? Installation of convergence stations in the longwall headgate to monitor roof movement during mining. ? Measurement of side abutment stresses in a yield pillar in the area of the convergence measurements. ? Measurements of coal fracture distribution by the detail area method. ? Rock properties determinations of roof, coal, and floor rocks; samples obtained by core drilling. ? Determination of floor bearing capacity by in-situ testing.

Jan 1, 1982

By Chao-jiong Hou

The necessity of using tensible rockbolt in the roadway with soft rock, high in-situ stresses, mining influence and other complex conditions was discussed, the structures of three kinds of tonsibte rockbolt and design principle were introduced in this paper. The tests of analogue material simulation under plane strain condition and underground industrial tests indicated that the effect of controlling deformation surrounding roadway by use of tensible rockbolt was good.

Jan 1, 1989

By Bob Coutts, Matt Martin, Dan Lynch, Dan Payne

"The Broadmeadow punch longwall coal mine in Central Queensland Australia has experienced significant highwall movement associated with the effect of longwall subsidence when the longwalls approach their final position close to the open-cut highwall. In response to this movement, Broadmeadow employed two types of broadscale highwall monitoring (radar and laser scanners) to provide full coverage measurement throughout three consecutive longwalls approaching the highwall. This was to attain a better understanding of the mechanism causing the movement and potentially enable prediction of instability. Results from the monitoring found the highwall is displaced to magnitudes unlike those typically measured in open-cut mining and in direct contrast with typical longwall subsidence behaviour.This paper discusses the ground movements measured, monitoring methods used, safety measures established, as well as theorising the failure mechanism. Recommendations are made for mine and pit designs for future punch longwall layouts. The paper shows how the movements measured are more aligned to some measurements made during stream valley closure studies previously presented at the ICGCM and challenge the mechanisms suggested by previous literature.BACKGROUNDThe mining of longwalls under or adjacent to large voids (e.g., stream valleys, escarpments, or cliffs) is commonly associated with heavily vegetated or steep surface areas. In areas of extreme topographic variance, access to traditional survey pegs and stations or even new radar or laser technologies is limited. In addition, seldom have the longwall layouts aligned themselves parallel or perpendicular to the surface feature, making interpretation of any available surface movement data more complicated.The punch longwall layout (Figure 1) is also quite uncommon (only undertaken at a small number of longwall mines in Australia) but creates the perfect configuration to enable a somewhat controlled study of the effect of longwall subsidence on a steeply dipping surface feature (an un-vegetated, evenly excavated open-cut highwall). The relatively recently developed radar and laser scanning technology has also enabled near continuous, real-time, sub-millimetre monitoring of a full 500m wide x 100m high highwall. Because the punch longwall enables access and a clear view, the technology could be easily deployed as compared to the highly vegetated and variable topography of stream valleys."

Jan 1, 2018

By Khamis Y. Haramy

The U.S. Bureau of Mines installed surface and subsurface instruments at a mine site in Colorado to monitor and characterize the overburden response to longwall mining. Instrumentation included a time-domain reflectometry (TDR) cable, a multiple-point borehole extensometer (MPBX), vertical-deformation surface monuments, and in-mine pressure cells for monitoring abutment, pillar, and gob loads with respect to the longwall face position. The purpose of the study was to collect data that could be analyzed to correlate the design of the mine layout to the resulting overburden failure response. Determining the extent of caving and fracturing is important in the arid and semiarid Western United States because of the possible consequences to the fragile underground hydrologic systems upon which the land owners and users depend. This study is unique from past investigations because the overburden contains massive sandstone members that impose special conditions on the caving process and pressure redistribution above the longwall panels. This paper presents the results of this correlation study.

Jan 1, 1992

By Deren Zhu

Based on the results of field observation and physical model analyses, a computer simulation method, FEAEBP, has been developed for simulating the breakage of the main roof by considering it as a Kirchhoff plate on Winkler elastic foundation. By this method various parameters of rock property, different boundary conditions of the working face and the initiation, development and results of the breaking process of the main roof with different geometric dimensions can be effectively simulated. Since the main and immediate roofs, and the coal seams are treated as an integrated mechanical system, the interaction among them can be studied in detail.

Jan 1, 1988

By Peter Cain

Twenty years of research into the design of permanent gateroad support (packs) in coal mines have resulted in two methods of pack design based on engineering principles. The first, the detached block concept, is based on static loading of the support system by an hypothetical detached block. The second, the roof beam tilt concept, is based on the dynamic loading of the support system as the roof beam tilts over the roadway about a pivot point located in the rib-side. The roof beam tilt concept has been used on a number of occasions to design packs in a variety of conditions. However, recent work in the Sydney Coalfield of Cape Breton Island, Nova Scotia, has shown that design criteria based on the roof beam tilt concept in its present state of development are far from universal in application. After a review of published pack performance data, including detailed studies conducted in the UK, France and Canada, it was found that consideration of the mechanical properties of the roof beam produced a design criterion that fitted the available data. Modifications to the design process using the roof beam tilt concept are suggested for use in pack design. The work also revealed that current research in other aspects of coal mine ground control, particularly the areas of powered support design and subsidence prediction, may provide valuable information leading to major advances in this field. Such developments could also extend the application of the roof beam tilt concept to the design of pillar systems.

Jan 1, 1993

In recent years, improvements made to the longwall system have accelerated at a faster pace than those made to the gate entry development system. As a consequence, unless planned years ahead of time, extending the panel length is nearly impossible without some innovative approach. At Cyprus Amax Coal's Emerald mine the G panel length was extended by 3,500 ft- by developing three entries across it to facilitate development of its headgate and tailgate entries simultaneously when the adjoining F panel was in operation. After evaluating alternative supporting methods and associated risks, determination was made to backfill these entries and crosscuts using a low strength flyash cement mixture prior to mining thru. Instrumentation was also used to monitor the stress change or front abutment stress in both the coal and the backfilled material ahead of the face. Longwall mining thru these three entries took about four eight-hour shifts and proved to be very successful. The designed flyash cement mixture provided adequate roof stability and caused no difficulty in the shearer's cutting while eliminating an in-panel longwall face move and minimizing the risk of roof or floor failure in the in-panel openings, or in the worst scenario loss of the face during the longwall cutting thru. This approach provided the intended result of extending G panel and recovered about one million tons of coal. This paper summarizes the engineering design of the cutting-thru project and flyash cement mixture, front abutment stress changes within the longwall coal block, backfilled material, and coal pillars ahead of the longwall face, and our underground observations

Jan 1, 1997

By Timothy Ross

The Pittsburg & Midway Coal Mining Co.'s Kemmerer Mine is one of the deepest surface coal operations in the world, with the highwall extending to approximately 1,000 ft above the pit floor. To increase recovery, auger mining is being evaluated beneath the highwalls of several seams representing the current economic limit of pit development. The primary augered seam is over 50 ft thick, can approach 100 ft thick, and dips into the highwall at an average of 17 degrees. The seam thickness and dip present many geotechnical design and operational challenges for multiple Sup to five) lift augering. This paper presents the design criteria and methodology applied to determine appropriate web and septum thicknesses for the various cover depths anticipated, as well as operational measures that can be taken to increase overall coal recovery. The primary tool used in the design was the finite difference code FLAG. Models incorporating typical strata sequences associated with the coal seam were run at several different cover depths corresponding to the maximum anticipated auger penetration. Web and septum thicknesses were varied until the minimum thickness satisfying a given safety factor criterion was determined. Using this procedure, design curves were developed for web and septum thickness versus cover depth. Operationally, several recommendations were developed to ensure that overall coal recovery is maximized. By angering across the scam dip, auger penetration per hole can he increased dramatically, and by carefully planning maximum planned auger penetration versus hole spacing, increased coal recovery can be safely attained.

Jan 1, 1999

By Ezzeddin Bakhtavar

There are several geotechnical challenges and risks inherent in the interaction between the open-pit and block cave mining environments. This is especially true when they have to work simultaneously for a short time, as well as when only the caving operation is continued. Some of these challenges and risks include the induced zones of stress due to the large and deep open-pit, instability of the slope, instability of the crown pillar and water inflows, subsidence, and sometimes instability of the main accesses to the block cave portion of the mine. These challenges usually occur due to cave propagation. In this paper, these geotechnical challenges and associated risks have been studied and discussed. It was concluded that the majority of the mentioned geotechnical risks could be decreased, and often eliminated, by considering the appropriate dimensions of a stable crown pillar, especially in simultaneously working open-pit and block caving operations.

Jan 1, 2011

By Anton Sroka

The German hard coal production predominantly derives from underground multiseam mining activities. Beside common surface damages, ?inner mine damages? on underground infrastructures (i.e. main roads, cross cuts and shafts) due to mining excavations occur to an increasing extent. As these "inner mine damages" dramatically increased because of the development towards high performance longwall mining technologies, this matter raised to be a severe problem concerning mining economics. To protect durable and long lasting underground infrastructures, precautionary measures such as suitable mine layouts, adapted planning of mining operations and moderate face advances have to be considered. Some examples of "inner mine damages" recorded by means of mine surveying methods are given in this paper. An empirical-mathematical model based on the principles of mining subsidence engineering methods will be introduced. This model allows to minimize ?inner mine damages? and helps to support and optimize mining processes.

Jan 1, 1999

By Sun Henghu

This paper analyses problems associated with cement based technique in metal mines, and provides a new mining technique of packing the tailing sand and water into solidified material. In the new technique, the cementing agent is a solidifying material containing a high percentage of water and tailing sand. The sand and water solidify into the packed body at the same time. The slurry of the packed body varies widely in concentration and suitability for different mining conditions. It consists of two liquid materials, each composed of a cementing agent, tailing sand and water. The thick liquids are transported to the packing place at the same time. Their pumping property is good; they do not solidify or block up the pipe during transportation. At the packing place, the two liquids are evenly mixed. The mixed liquid flattens out well and its solidifying speed is so fast that it solidifies into a packed body within a very short period of time. The compressed strength of the packed body can reach 1.2-5MPa in one day, which satisfies the requirements of different mining conditions. By using the new mining technique, all the tailing sand can be used again in the packed body and it is low in cost and investment. The mechanisation is easy and thus the working efficiency is increased and the use of labour decreased. Contamination problems caused by excess water drainage under the ground are resolved.

Jan 1, 1992

By Xicai Gao

With the intensification and expansion of deep coal mining, the surrounding rock stress environment becomes further deteriorated because of the complicated geological environment and powerful mining effect, so the major deformation of roadway appeared frequently. The proportions of floor heave are increasing and , the most serious problem is the floor heave of preparatory workings. The coal seam of Binchang coal area in Shaanxi province is at a depth of 621.6 ~ 817.0 m, the average thickness of the coal seam is 25 m, and the overburden and coal measure strata are the main regional aquifers and are highly permeable. The properties of water-weakening are obvious in the floor strata. The main preparatory workings or chambers were driven in the coal seam. The severe floor heave of the water chamber appeared during early mining and the amount was 180 ~ 910mm, and seriously affected the normal installation and use of the water chamber. Theoretical study and numerical simulation as well as the in-situ measurements were carried out to investigate the deformation and failure characteristic of the surrounding rock with non-support in the floor and the main reasons which caused the floor heave were determined. A new combined support technology was proposed which consists of overcutting, grouting, backfilling and invertedarch and bolt-grouting. The field monitoring showed that the cumulative convergence of the water chamber was 20mm, the maximum convergence speed is 1.2 ~ 2mm/d, the accumulative convergence of two ribs was 36mm and the maximum convergence speed is 2mm/d. The combined support technology will enhance the support intensity between the roof and floor, the two sides of the entry and improve the loading capacity of the floor effectively and the floor heave can be controlled effectively.

Jan 1, 2013

By Pier Paolo Manca

The investigated area lies close to a large town and covers an area of about lkm2. The mine was worked at depths ranging from 5 to 100 meters but mining operations actually ceased some 50 years ago. There are seven coal seams, each one to two meters thick, overlain by sedimentary rocks in a strongly faulted area. Different kinds of subsidence have occurred, crown holes, shallow depressions and hummocky ground. The results of rock mechanical characterisation (RMR method) in the area have been used to define three different types of numerical model (FLAC 2D). A large numbers of simulations has been performed to solve three different problems at three different scales: to determine the, mechanical properties of the roof rock and overburden involved in the subsidence process, to assess the crown hole subsidence potential and to define the properties of the beam foundations.

Jan 1, 1999

By John P. Dunford

Ground support continues to be the most important safety consideration in underground mining. The Bureau of Mines has developed a yielding steel post with a capacity of 45 tons and b c1osure allowance of 24 inches in a 6 to 7 foot seam height. The post mechanism in a three piece unit consisting of a top and bottom leg made from standard steel pipe and a separate foot bracket. It develops its load carrying ability when the lower pipe, with an attached interference ring, is forced into the larger top leg. The walls of the top leg are deformed radially and along the axis. Yield continues until the unit bottoms out. Other advantages of the post is that due to its simplicity it can be made at the mine shop level and its cost should be about one-hundred dollars. Prototype units were tested in the laboratory. Based on these results, modifications were made that would make the post perform better as a mine support. Two field tests were conducted. The first test used the units as supplemental support for the wood crib rows in a longwall tailgate. The second and larger field teat had 84 posts placed on salvaged track rails. They were installed on two foot centers in the middle of the entry. Overall the supports functioned well during use in the headgate entry, but problems with the quality of some of the pipe caused localized failures. However, these problems can be attributed to one manufacturer of pipe and through tighter specifications can be eliminated. The use of the posts with the rails is showing additional benefits as a ground support system. By providing continuous support between the posts a beam is created that has much more load bearing. The additional support can reduce floor heave and in some cases eliminate the need for the rib side crib line.

Jan 1, 1986

By Rene Rodriguez

The initial results of our investigations on the applicability of geophysical exploration methods to map coal seam inclusions were summarized in a paper submitted at the Thirteenth Conference on Ground Control in Mining in 1994. These investigations were continued under a variety of conditions at a number of underground coal mining operations. The results have been encouraging and have fostered a much more detailed understanding of the geophysical principles at work in underground mine mapping. This report summarizes a particularly interesting application, that is, the use of Underground In-Seam Seismic exploration methods to identify and to approximately delineate coal seam inclusions within longwall panels. The methodology relies on the excitation of seismic sources in the coal seam along one side of the panel and the recording of seismic waves by geophones secured to the coal rib on the opposite side. Head-Body waves (compressional and shear), direct and channel waves are generated in the process. While the head waves are critically refracted waves traveling at the coal floor and roof, direct and channel waves are transmitted through the coal body and are dispersive in character. Tomographic techniques applied to the velocity inversion of first arrivals permits a fast mapping of coal seam inclusions in the panel. The process incorporates path velocity and geostatistical intersect analysis. Full wave analysis of the dispersive channel waves, provides an independent and confirmatory information of the coal geometry, including the inclusions within. The inversion technique in this case is the modal analysis of the wave trains. The application of this method to three different problems was confirmed by subsequent mining of the predicted anomalies, proving the accuracy of the technique within limits of experimental error.

Jan 1, 1995

By George B. Quaye

Conventionally, roadways in South African collieries are 6 to 7 m wide. This dimension is chosen so as to allow maneuvrability of appropriate mine machinery and equipment, to meet production requirements and to ensure roof stability. Over the last two decades, a great deal of research effort has been expended to understand the behaviour of roadways in different strata within this width range. The results have improved the understanding of the strata behaviour to such an extent that 6 m wide roadways are developed with a high degree of confidence. With the advancement of technology and the quest to mine at a lower cost, some mines in South Africa have started considering the benefits of other types of mine machinery that will require much wider roadways to ensure optimum productivity. The roadways required will have to be about 10 - 14 m wide. The challenge confronting these coal mining companies is the potential instability that might be associated with such wide roadways. This dilemma is aggravated by the fact that, apart from theory, nothing is known about the expected behaviour of such wide roadways. This led to experimentation at a selected site in a South African coal mine where 10 m and 14 m wide roadways were developed and monitored. This paper highlights the experimental procedure adopted, discusses the results obtained, compares the prediction of elastic theory to reality and set the precedence towards understanding the behaviour of wider roadways in South Africa.

Jan 1, 2001

By Daniel S. Mazzei

This paper will be a general discussion of surface flooding considerations as they affect mining facilities site selection, based primarily on experience with several such problems with which MSHA's Bruceton Technical Support staff has been involved. The detailed analytical procedures used in arriving at engineering solutions of these problems will not he presented here; the emphasis is on drawing attention to this additional aspect of mine design which hitherto has been largely overlooked due to insufficient awareness, information and criteria. The paper's purpose is to stimulate thought and offer guidance concerning the selection of sites for mining facilities in light of the potential for flooding problems caused by surface waters. Flooding by surface waters, would generally not be a serious consideration in areas of relatively low topographical relief, i.e. flat lands, although there are exceptions to this rule, for example, in Western areas where flash flooding is a major concern. Therefore, this discussion will mainly apply to areas where the severity of surface flooding would be amplified by the topography-large, well defined watersheds of considerable relief, i.e. mountainous areas. In these regions, steep valley walls cause any rainfall to flow quickly into the relatively narrow valley bottoms. These valley bottoms provide little flow area during storm conditions, so deep and rapidly flowing streams result.

Jan 1, 1982