Search Documents

By Eugene D. Krupa

Mine 33 of Beth Energy has serious and complex roof cutter problems causing delay of the advance rate of both the entry development and longwall face retreat. The cost of maintaining these entries is very high due to the requirement of wry heavy artificial supports. It was suspected that this problem was caused by multiple factors including high in-situ horizontal stresses and weak roof in the problem areas. In order to alleviate the problem, proper design of panel entry and roof reinforcement were considered. This paper presents the results of extensive measurements in experimental panel entries of Mine 33 in order to assess the performance of the designed structure and roof support system during the entry development and longwall retreat. An experimental panel entry has been designed and implemented. The designed parameters were varied seeking for the most ideal parameters which provide stable roadways. Changing these parameters accompanied instrumentation of roof, floor, and pillars. Typical instrumentation, including stress meters, convergence measurement stations, and borehole borescope were utilued. Gnensive monitoring of the behavior of the designed structure and support system led to the development of a complete stress-deformation history of the roadway and an ideal roof reinforcement, support system, which reduced the cost of entry development by less than a third of the previous method.

Jan 1, 1990

By David F. Gearhart

A cooperative study was conducted between Signal Peak Energy and the National Institute for Occupational Safety and Health (NIOSH) to evaluate the behavior of a pre-driven recovery room under less than 200 ft of cover. The design of the support systems for a pre-driven recovery room must provide control of the roof and ribs during the changing stress environment experienced throughout the final advance of the longwall into the recovery room. It must also provide a stable area where mine personnel are not exposed to undue hazards during shield recovery operations. This recovery room was constructed in two phases; each phase mined a 21-ft-wide room that was heavily supported, and subsequently fully backfilled with 800-psi, cellular concrete. Instrumentation to monitor the recovery room performance included borehole pressure cells (BPCs) placed in the head gate and tailgate pillars, at four locations across the longwall panel, in the fill material, and in the first row of outby pillars near the center of the panel. Four roof-to-floor convergence sensors were installed in the back fill material and a vertical, multipoint borehole extensometer (MPBX) measured the displacement of the strata above the recovery room. Surface surveys were conducted to measure MPBX collar movement. The data show that the front abutment load was transferred onto the recovery room backfill and the out by pillars as the longwall panel was extracted. As the longwall approached the recovery area, the fender and shields yielded, but the backfill provided enough support to keep the room stable as the longwall advanced to its final position. The system worked as planned and the face was recovered in record time.

Jan 1, 2014

By Yao Yuping

The strength and deformation of more than two hundred coal samples have been tested in the condition of triaxial compression. The regression equation showing the relationship between coal strength and pressure in the pores as well as confining pressure, was obtained. The appropriate calculation for stress-strain curve was carried out. Further, an analysis shows the variation of coal strength and its modulus of elasticity in methane medium.

Jan 1, 1992

By John Latilla

Following its introduction on underground collieries, the mandatory Code of Practice to Combat Rockfall Accidents (CoP) was applied to all opencast operations of lngwe Collieries (the South African division of BHP Billiton Energy Coal). The CoP includes, but is not limited to, requirements to assess hazards, manage them and monitor compliance. Information on methods to measure highwall conditions and compliance with control measures on opencast strip mines, as opposed to open pit mines, was found to be anything but freely available. However, on the Ingwe underground mines, a system of rating physical conditions in each section and how well production personnel were managing the situation, has been used with success for some time. It was decided that a similar approach would be taken, and, as with the underground rating system, the resultant rating forms should not be aimed at rock engineering specialists only but should be able to be used by production personnel as well. This paper discusses the highwall risk rating method as evolved over a couple of years and highlights that it is a flexible tool that can easily be changed to suit an individual mine's requirements. It also shows how operational aspects are being measured to determine how well the identified hazards are being managed. Allied to the method is a relatively easy, and certainly "low capex," mapping technique which allows between 500 and 1000m of highwall to be covered in a day. Features generally recorded include lithology, bench height, work still to be completed, coal losses or "toes", presence of water, dolerite intrusions, existing and potential failures, prominent joints, declared special and cautionary areas, cracks on upper benches and condition of spoil piles. Highwall mapping and photography as well as basic geological data collection, enable highwall risk and operational ratings to be determined. The same rating sheets may also be completed by production personnel, but without detailed mapping.

Jan 1, 2002

By David Oyler

Unusual circumstances may require that a longwall retreat into or through a previously driven room. The operation can be completed successfully, but there have been a number of spectacular failures which exposed miners to serious roof fall hazards. To help determine what factors contribute to such failures, the National Institute for Occupational Safety and Health (NIOSH) compiled a comprehensive international database of 130 case histories. The cases include five failures where major rock falls occurred in front of the shields, and six even more serious failures involving major overburden weighting. This suggests two room failure mechanisms. The first is a roof fall type failure caused by loading of the immediate roof at the face as the fender narrows. The second is a weighting type failure caused by the inability of the roof to bridge the recovery room and face area, and affecting rock well above the immediate roof. The data indicate that the roof fall type of failure is less likely when intensive roof reinforcement (bolts, cables, and trusses) is employed together with higher-capacity shields. The overburden weighting failures, in contrast, occurred when the roof was weak and little standing support was used.

Jan 1, 1998

By Syd S. Peng

A total of 209 cases of subsidence data over longwall panels in 16 US coal seems have been collected and built into a subsidence database. The database is developed under MS Windows environment. It uses a very user-friendly menu driven system. The empirical formulae for a number of commonly used subsidence parameters have been derived from those collected subsidence data.

Jan 1, 1995

By Raymond M. Stateham

The Bureau of Mines has developed a portable, lightweight device for determining the integrity of resin-grouted roof bolts. The instrument functions by sending a known pulse of ulstrasonic energy into the bolt and comparing the amount of energy reflected hack with the original measured pulse. Where the bolt is properly bonded or coupled with the rock, the energy passes through the bolt-resin-rock interface and dissipates in the rock. Where the bolt is not properly coupled, the energy is reflected back along the bolt to the instrument. The ratio of reflected energy to the pulse approximates the fraction of the bolt's surface that is improperly bonded. The instrument is easy to use. The operator holds the sensor head of the device firmly over the head of the bolt to be tested, causing the pulse of ultrasonic energy to be imparted to the bolt. The device then listens for reflected energy. This cycle is repeated about 200 times per second until an evaluation of the bolt installation is made and indicated by colored lights in the display window. Bolts having 50% or less of their surface bonded are considered had and cause a red light to he illuminated. Bolts with 50% to 75% of their surface bonded cause a yellow light to be lit and are considered marginal. Bolts having more than 75% of their surface bonded are considered good and cause a green light to be lit. The indicator lamp remains on for about 4 seconds and then goes off, indicating that the instrument is ready for another test.

Jan 1, 1982

By Zhang Liandong

Roof control in thick-seam mining has long been a difficult problem in mine design and coal mining. In the early 1980's, through ground control instrumentation and investigation the rules of roof strata movement were determined, based on which the sliding roof bar powered support was properly designed and successfully applied to roof control to thick seam mining with caving. Underground trials in Huating Coal Mine produced satisfying results. The technique is being employed in many Chinese coal mines and won the national price for technical advance.

Jan 1, 1990

By N. P. Kripakov

The U.S. Bureau of Mines (USBM) is conducting research to develop a practical computer-based tool that will allow coal mine planners to anticipate rock mass behavior surrounding mine entries prior to actual mining. More specifically, this tool estimates to what degree and extent the immediate roof and floor strata and the coal pillar ribs surrounding an opening will weaken or fail for a given set of mining parameters. The technical approach couples together two numerical techniques: the boundary-element method and the finite-element method to allow for an approximate three-dimensional simulation of actual mining situations. Outputs from plan-view, linear-elastic, boundary-element models executed at different mining stages are used as input to a detailed, section-view, finite-element model to estimate the degree and extent of failure expected to occur around the periphery of an entry system. Using a pseudo-elastic approach. elastic rock mass properties are continually updated as different zones are predicted to fail. The procedure is relatively easy to use and is being set up to work interactively with the user who will not be expected to be a computer expert. Inputs include easily understood parameters obtainable from the field and rock mechanics laboratories. Examples of computer-generated output from generic sample models representing typical mining situations are presented and results discussed.

Jan 1, 1994

By S. K. Sharma

The present study attempts to critically review the pillar-design as required by Coal Mines Regulations of India vis-a-vis latest rockmechanics formulae, Equivalent material modelling was the approach adopted for testing the safety and stability of the pillar sizes predicted by various formulae. Two parameters, considered here for calculating pillar sizes was the stresses acting over the pillars and the strength of the pillars. Stresses acting on the pillars were calculated by the tributary area method. Based on the studies of Coates and Hustrulid, the stress obtained was reduced by 40 percent. For calculating the strength of the pillars, three formulae, namely Holland and Gaddy, Salamon and Munro and Central Mining Research Station, India, were used. The pillar widths were then determined by equating the product of recommended factor of safety and pillar stress with the pillar strength.

Jan 1, 1992

By Daniel W. H. Su

Surface subsidence induced by multiple-panel coal extraction was calculated with finite element stress analysis. The use of nonlinear material behavior and GAP elements, which provide a realistic representation of shearing along existing planes of weakness, allows the finite element program to accurately reproduce observed subsidence profiles. A reduction factor of 1/6 is applied to the measured rock strength and modulus for use in the finite element model. The models satisfactorily predict a significant change in maximum subsidence and subsidence profile associated with an increase from subcritical to near critical panel width. Modeled shearing along planes of weakness is in good agreement with available time domain reflectometry field observations and is demon¬strated to have a very profound effect on the maximum subsidence and the shape of the subsidence profile. When both material nonlinearity and planes of weakness are incorporated, the finite element model appears to possess great potential for accurately predicting surface subsidence and subsurface strata deformation in environments where little subsidence information is available.

Jan 1, 1990

By D. L. Price

This paper presents a method of measuring field power consumption of shearers and deriving specific energy consumption versus shearer haulage speed performance curves. A description of a computer program which simulates the cutting action of a shearer drum is presented. A comparison between the field specific energy curves and the computer simulation results is made. The simulation results compare well with the field data where all the coal seam is being cut by the shearer. The computer simulation results give hack-calculated field pick force cutting characteristics, which allow the performance of the shearer to be predicted for other operating conditions, e.g. effect of changes to pick lacing, effect of changing the drum rotational speed, allows the calculation of power requirements for a particular production rate.

Jan 1, 1992

By J. G. Stewart

Polyurethane injection for the consolidation and control of broken strata is a common practice in the deep mines in Europe. The technology has gained wide acceptance in the coal mines of America since the introduction of RokLok polyurethane binder by Mobay Chemical Corporation in 1977. A popular and growing use for polyurethane consolidation grouting is to control the roof and prevent gob flushing during recovery of longwall face equipment. The technique provides many time and performance-related benefits compared to more conventional methods using wire mesh. Kitt Energy Corporation installed the nation's first 1000-feat longwall face in April and May of 1984. The face completed the first panel in October, 1984, and recovery was begun. Roof Strata consolidation for the recovery was accomplished by a RokLok polyurethane binder infection program designed and supervised by Halbach & Braun Industries. The application provided the most rigorous and demanding test to date of this method's performance and cost-effectiveness relative to bolts and wire screen.

Jan 1, 1984

By Collin Stewart

Bowie Resources, LLC (Bowie) has been using the Stability Mapping System (SMS) developed by Dr. Keith Heasley, West Virginia University, since 2005. Seven three-entry longwall gateroads, four longwall panels and a five-entry set of mains have been mined in two different seams in areas originally analyzed with the SMS. This paper compares predictions of mining conditions based on the SMS with actual mining conditions. Specific comparisons include longwall and continuous miner (CM) productivity, longwall tailgate response and support and CM roof bolting requirements. The paper also discusses current thoughts at Bowie on the use of different weighting factors for CM development, longwall face conditions and longwall tailgate support requirements.

Jan 1, 2007

By Freddie Hunter

An underground mining method for extracting an eight metre (26') coal horizon, containing a sandstone layer. A decrease in the thickness of the rock strata between the number two and number three seams of the Sasolburg Coal Field, has resulted in a total mining horizon approximately eight metres (26') thick. This parting varies in thickness and competency and in some areas is impractical to cut with a continuous miner. In addition, the general mining area is highly jointed. The top seam is first mined to a normal bord and pillar plan with a continuous miner. The bottom seam is then mined by selectively undercutting the stone parting constituting the floor of the top seam. In areas where this parting is between 0.75 - 2.50 metres (29.5" - 98") thick, it is suspended from the primary roof support installed when mining the top seam. Secondary, high extraction retreat mining is then undertaken in the coal pillars adjacent to the suspension supported headings in the bottom seam. Left in-situ, the parting provides lateral support to the pillar sidewalls in both the top and bottom seams, enabling high percentage extraction rates in what was previously thought an uneconomically mineable area. The paper proposed, presents the challenges and practical implications of executing the mining method, including the primary roof control of the top seam and the stone parting between scams.

Jan 1, 2003

By Liu Changyou

This paper analyzes experimentally the stress-strain relationship and the characteristics and variation trends of acoustic emission signals of the medium- and high-burst-prone coal/rock fracture process. The precursor and sensitive characteristics of the acoustic emissions when the burst-prone coal/rock fracture occurs were obtained. The characteristic index and the feasibility for predicting rock bursts using acoustic emissions technology were proposed. Keywords: burst-prone coal/rock, acoustic emissions, energy, prediction index

Jan 1, 2003

By Michael Alber

Pullout tests on resin grouted rock bolts have been executed in coal mines and surface test sites. The goal of this study was to provide some qualitative information about the rock mass quality from mandatory tests with a bit little more effort. Movements of rock bolt head and steel plate at different load levels were analyzed and were found to yield information about the rock mass deformability. The tests were interpreted similar to plate bearing tests and a rock mass compressibility index C was assigned. This index reflects the complex interactions between the rock mass, resin grout and bolt under load. Although further research is necessary it may be concluded that those tests may aid in recognizing geological conditions.

Jan 1, 2003

By Michael Alber

Coal resource extraction reaches higher depth of overburden and rockbursts as well as associated seismic events appear to become an additional problem to he addressed by ground control engineers. For example, German coal mines approach a depth of overburden of some 1400 m (4200 ft). Certain strata at those depths and associated high stresses may react upon resource extraction and subsequent deformation by violent release of strain energy, termed rodcbursts. Rock mechanics tests on numerous rock types have been conducted and three types of brittle rock behavior were classified. This paper describes different types of rock behavior in uniaxial compression and discusses a possible classification of rock with respect to their likelihood of violent response upon loading.

Jan 1, 2004

By K. Y. Haramy

This report describes the development of an equation for predicting the crushing strength of 2-inch (5.08-cm) cubes of coal from point load tests made on irregular lumps. The equation was developed from point load and cube crushing strength tests performed on coal samples from six Western U.S. coal seams. For the six coals tested, the means of the point loads [(P)] in kg at failure were approximately proportional to the deans it the distances [(V)], in cm between the platen points for lumps in the 2 to 10-cm size ramie. This finding is at variance with results of tests on other rock types reported in the literature, which tend to show that P is proportional to D2 , as is normally assumed (in theoretical grounds. [The average crushing strength of a 2-inch (5.08 cu) cane for each type of coal was plotted against the log 10 of the slope of the P vs D plots, AP/AID . A straight line was fitted to these plots. The equation of the fitted line is cr = 1.72 x 10 4 10gK -2.10 x 10 4, where Cr is re estimated 2-inch (5. 08-cu,) cube crushing strength of the coal in psi and K is the scope of the straight line fitted to a plat of P v D for the same coal.]

Jan 1, 1982

By L. Mahony

This paper describes the design, construction and commissioning testing program for a laboratory facility at the School of Mining Engineering, UNSW, Australia, aimed at evaluating reinforcement tendon performance when subjected to shear loading. The project has been financially supported through the coal industry ACARP research initiative. The single failure plane design adopted in the test rig has been successful in allowing shear loading to be directly applied to fully installed (and where relevant, pre-tensioned) rock bolts. Initial results are extremely encouraging, and illustrate a significant axial component of load development as shearing takes place - particular in lower strength, softer material types. The paper also outlines future plans for use of this facility.

Jan 1, 2005