Search Documents

By Erik Westman

Coal bumps remain one of the industry?s most devastating but least understood phenomena. If changes to the internal conditions of the rock mass could be observed there is hope that bumps could be forecasted. Seismic tomography has been used over the past 25 years in an attempt to image these changing conditions in the vicinity of the longwall face. This paper describes the history and practical considerations of using seismic tomography in bump-prone coal mines. The implementation of seismic tomography at six different longwall mines will be described along with lessons learned. Early studies used mining independent sources of seismic energy, including explosives and sledgehammers. Subsequently more operator friendly sources, such as the mining equipment itself and mining-induced seismicity, were used. Seismic energy sensors have been placed in gateroads and on the surface above the mine. Each of these configurations has associated advantages and disadvantages. Although the results obtained have been encouraging, the application of seismic tomography to monitoring a bump-prone longwall face is still immature. The ultimate goal of clearly imaging changing stress conditions in the longwall panel in a manner that does not inhibit mining operation is still distant, yet drawing nearer. When this goal is achieved, the industry will have a capable tool for identifying locations where bumps are imminent.

Jan 1, 2008

By Ted Klemetti

Roof deterioration in weak moisture-sensitive rock leads to roof falls in coal mines. An observation site was set up in intake air at an underground coal mine in central Ohio to evaluate the time-dependent deterioration of moisture-sensitive roof rock. By periodically collecting and weighing the rock falling from the roof, the National Institute for Occupational Safety and Health (NIOSH) was able to quantify the deterioration of the moisture-sensitive shale roof. The measurements showed that more roof rock is falling in the dry winter months. Movements in an intersection were monitored in order to determine if deformation correlated with seasonal changes in temperature and humidity. The rate of intersection roof-to-floor convergence was found to be cyclical and related to seasonal changes, with more convergence during the months of April through September. At the study site intersection, the roof beam did not show deflection indicating movement most likely due to mine floor deformation. The bolt load also increased in the warmer months before shedding load, possibly due to rock failure. Temperature and relative humidity sensors, placed in holes in the roof show that mine air does not mix with the air in the holes. Consistent saturation levels of relative humidity were measured in the holes and it appears that high levels of moisture may have migrated into the bolt holes from roof shales. A roof sealant applied to a portion of the test roof appears to be preserving the roof and reducing the amount of rock fall into the entry, while the screened area virtually eliminated rock falling from the roof.

Jan 1, 2009

By Swapan Bhattacharya

United States federal and state regulatory authorities require underground mine operators to adopt adequate measures to minimize material damage to the surface caused by nine subsidence. This paper presents an approach to define and determine the extent of material damage due to subsidence from underground coal mining. The basic steps involved in the development of adequate criteria have been enumerated together with the approaches and methodologies used.

Jan 1, 1984

By Michael Alber

Resin grouted rock bolts are the major support measure in coal mining. They are rather easy and foolproof to install, take immediately load and are the least time consuming support measure for controlling gateroad deformation. The use of only resin grouted bolts allows fast gateroad development which is essential for economical resource exploitation. The design of reinforcement / support systems for coal mining typically bases on empirical methods, which work fine when encountering known or usual ground conditions. However, coal mining approaches depths where little experience exists and numerical modeling is often the only method to estimate ground behavior. This paper discusses the geotechnical properties relevant to numerical model and focuses particularly on input values for modeling resin grouted rock bolts for safe gate design.

Jan 1, 2006

By Ihsan Berk Tulu, Keith A. Heasley, Chris Mark

"The Analysis of Retreat l\.fining Pillar Stability (ARJ\1PS) and the Lal\.fodel programs have been used successfully in the U.S. for designing safe pillar recovery operations for many years. However, the recent Crandall Canyon l\.fine collapse showed that further research is required to improve the pillar design for recovery under deep cover. To this end, the National Institute for Occupational Safety and Health (NIOSH) and the West Virginia University (WVU) l\.fining Engineering Department have been working together to improve both the ARJ\1PS and the Lal\.fodel programs.This paper compares and analyzes the overburden loads calculated by ARJ\1PS 2002, the new ARJ\1PS 2010, and the Lal\.fodel program with regard to the retreat pillar line, the gob, and the barrier pillars. The analysis shows a number of distinct differences between the ARJ\1PS and Lal\.fodel loading distributions. Ultimately, the programs, with their distinctive load distributions, are used to analyze a database of 52 deep cover pillar retreat case studies, and the ability of each program to discriminate between successful and unsuccessful retreat pillar plans is evaluated.INTRODUCTIONThe Analysis of Retreat l\.fining Pillar Stability (ARJ\.f PS) and the Lal\.fodel programs have been used successfully in the U.S. for designing safe pillar recovery operations for many years. However, the recent Crandall Canyon l\.fine collapse showed that further research is required to improve the pillar design for recovery under deep cover.Pillar recovery accounts for less than 10% of the coal produced from underground coal mines; however, in the period between 1989 and 1996, it accounted for more than 25% of all ground fatalities (l\.fark et al., 2003). In the past 15 years, the safety of retreat mining operations has greatly improved. l\.fark (2009) explains three steps promoted by l\1SHA and NIOSH for safer pillar recovery:1) Global stability through proper pillar design2) Local stability through proper roof support3) Worker safety through proper section managementThe ARJ\1PS and Lal\.fodel (Heasley, 1998) programs have been playing an important role in guiding mine operators in designing pillars to ensure the global stability of a retreat panel."

Jan 1, 2010

By Craig Compton

Falls of small pieces of rock from between roof bolts continue to cause fatalities and to injure hundreds of coal miners each year. Roof screen is the most effective way to prevent these incidents, but some mines are reluctant to use it because they believe installing screen can be awkward, expensive and time-consuming. The most common type of roof bolting machine used in mines today is the dual boom, outside-controlled roof bolter. Mines who install roof screen using these machines have developed some machine modifications and techniques to ease roof screen installation. This paper describes some successful techniques and machine modifications that are being used in productive mines to assist with roof screen installation. Since the material handling involved with roof screen installation can expose miners to an increased risk of musculoskeletal injuries, the National Institute for Occupational Safety and Health (NIOSH) ergonomists, designed machine modifications and implemented a series of tests to evaluate roof screen handling procedures for outside-controlled, dual boom roof bolting machines. Roof screen installation can also have a positive economic impact on a mine by reducing the cost of injuries, workers? compensation, required spot or re-bolting, and clean-up of long term travel and belt entries.

Jan 1, 2007

By Kirk W. McCabe

RokLok binder is a two-component polyurethane system consisting of a polymeric isocyanate (Component A) and a polyol resin (Component B). The two chemicals are mixed and injected into the mine rock under pressure. The initial low viscosity enables the RokLok material to permeate many of the smallest fractures. About 3-5 minutes after injection, the reacting material begins to expand in the fractures; the reaction is completed after 1-2 hours, and the material sets to a mechanically strong binder which adheres tightly to the rock. The consolidated rack provides resistance to any further f movement w thin the strata. The RokLok binder injection system is fast becoming an important engineering tool for coping with adverse underground geological conditions. Two case histories discussed in this paper, a longwall mining problem and an entry-roof problem, demonstrate the effectiveness of using the RokLok binder system to help solve complex ground-control problems in a cost-effective manner.

Jan 1, 1981

By Jennifer Riefenberg

Research efforts by the U.S. Bureau of Mines include running a series of displacement-discontinuity, boundary-element models to simulate the gateroad design at an underground coal mine in northwestern Colorado. The initial mine design is a yield-abutment chain pillar arrangement in a three-entry, longwall gateroad system. Pressure effects from mining the first and second panel were recorded using borehole pressure cells (BPCs). These field data were then compared directly to the model output. Observed yielding in the field was approximated by reducing material property values and/or removing pillar elements in the model. Model results using this calibration technique mirrored the field measurements consistently. Using the calibrated model parameters, a suite of models was run simulating an experimental entry design: exchanging the yield and abutment pillar locations. These model results reflect a 20¬to 33-percent reduction in core stresses in the yield pillar during mining of the second panel. Improved pillar and entry conditions are suggested by these predictive results. The design modifications were then implemented at the mine along a 150-m (500-ft) test section. Field observations and measurements from the experimental design test site compared favorably with trends of the model predictions.

Jan 1, 1993

By Kausik M. Sinha

Hydraulic stowing, which is being practiced in several major coal producing countries to deal with adverse mining conditions, usually permits almost 100% coal recovery from underground mines with minimal and controlled surface subsidence. It can be implemented in the US coal mines to reduce the severe effect of land subsidence and at the same time improve the cost of coal production, both of which are major setbacks for the coal industry in the USA

Jan 1, 1989

By Trevor Rangasamy

Technically based guidelines for managing rock related risks associated with strip mines in South African collieries are currently vague and are to a large extent based on experience and trial and error. To date, no mine specific or universal design charts exist within the South African industry. Quantification is done on a reactive basis i.e. following reported instabilities. The conditions under which, proactive tools to manage instabilities would be practically applicable are: The design of simple easy to use charts. Designing the charts for a target audience that is primarily production management. Well organized, logical set-up of the charts that will allow for easy future refinements. Allowing for variations in rock and soil properties within the charts that would account for colliery specific and region specific variability. The factors selected for in depth investigation that were deemed to have either individually or in combination, a primary influence on the stability of strip mines are (in no order of priority): Appropriate batter angles for ?soft? materials. Surcharge loading (spoils, dumps, topographical highs) on the highwall side. Influence of the thickness of stratification on stability. Influence of moisture content on stability. Influence of the changes to the coal seam dip angle on stability. Influence of persistent ?strip long axis? parallel faults/joints on stability. Spoil stability for variations in material type. This paper provides details of the work undertaken, using principally numerical modelling techniques, to produce design charts that will allow for proactive management of rock-related instabilities on strip mines.

Jan 1, 2008

By Karl H. Brandt

In the Auguste Victoria mine a bolted rectangular roadway has been kept open for the first time in the seam D/C after retreat. The target of the project was to gain a basis for planning and experience for future mining layouts in the same scam in view of the reuse of boated rectangular roadways. For this the roadway was additionally secured in sections with longbolts before the influence of the retreating panel had taken place. On retreat a concrete sidepack was concurrently put in place on the face side. The installed monitoring systems consisted of endoscopic devices, multiple extensometers (Tell-Tales), shear-tales, extensometers and convergence measurements. The experience that was gained was carried over into a physical and numerical model.

Jan 1, 2001

By Jinhua Wang

Based on engineering examples and theoretical analysis, the mechanism of chemical consolidation for fractured roadway surrounding rock was discussed. The chemical consolidating materials and three consolidating methods, that is, capsule, forced infusion and spraying, were introduced. Finally the application effects of the chemical consolidating technique to reinforce the fractured surrounding rock of roadways were analysed.

Jan 1, 1996

By G. Skybey

The Directional Drill Monitor (DDM) is an advanced instrument for real time in hole surveying. It was developed by Du Pont (Australia) to suit Australian gassy coal mining conditions. The instrument consists of three units: i. Down hole transmitter ii. Acoustic transducer iii. Data receiver processor unit (i.e. up hole unit). This paper describes the function of each unit in detail and highlights the importance of the DDM in long hole drilling efficiency. Surveying is carried out independent of hole depth. Each survey takes 2-3 minutes to complete, the frequency of surveying to control borehole trajectory is determined by the accuracy required for a particular hole. The DDM is currently being used successfully for long hole drilling in a number of collieries. A high degree of directional control has been achieved. Borehole trajectories were controlled to within +l¬2m of the planned path with intersurvey distances varying between 6 to 18 metres over distances up to 700 metres.

Jan 1, 1992

By Peter Zhang

"Room-and-pillar mining with pillar recovery has historically been associated with more than 25% of all ground-fall fatalities in the underground coal mines of the United States. The risk of ground falls during pillar recovery increases in multiple-seam mining conditions. The hazards associated with pillar recovery in multiple-seam mining include roof cutters, roof falls, rib rolls, coal outbursts, and floor heave. When pillar recovery is planned in multiple seams, it is critical to properly design the mining sequence and panel layout to minimize potential seam interaction. This paper addresses geotechnical considerations for concurrent pillar recovery in two coal seams with 70 ft of interburden under about 1,000 ft of depth of cover.The study finds that, for interburden thickness of 70 ft, the multiple seam mining influence zone in the lower seam is directly under the barrier pillar within about 100 ft from the gob edge of the upper seam. The peak stress in the interburden transfers down at an angle of approximately 20° away from the gob, and the entries and crosscuts in the influence zone are subjected to elevated stress during development and retreat. The study also suggests that, for full pillar recovery in close distance multiple seam scenarios, it is optimal to superimpose the gobs in both seams, but it is not necessary to superimpose the pillars. If the entries and / or crosscuts in the lower seam are developed outside the gob line of the upper seam, additional roof and rib support needs to be considered to account for the elevated stress in the multiple seam influence zone. INTRODUCTION Room-and-pillar mining accounted for about 40% of underground coal production in the United States in 2016. Pillar recovery, practiced in about one-third of the room-and-pillar mines, represents about 10% of the coal mined underground, yet it has historically been associated with more than 25% of all ground fall fatalities (Mark, Chase, and Pappas, 2003). In some U.S. coal fields, particularly central Appalachia, many coal mines are operating under geological conditions with multiple coal seams. The risk of ground falls during pillar recovery increases under multiple-seam mining conditions. The hazards of pillar recovery associated with multiple-seam mining include roof cutters, roof falls, rib rolls, coal outbursts, and floor heave (Mark and Tuchman, 2007; NIOSH, 2010b). Pillar retreating creates abutment pressure, not only in the currently mined seam, but also in the overlying or underlying seams. Multiple-seam interactions become more pronounced as overburden depth increases and interburden thickness decreases. To safely recover the pillars in multiple seams, it is critical to properly plan the mining sequence and panel layout to minimize potential multiple-seam interaction."

Jan 1, 2017

By John C. Stankus

The success of cable bolts for mine ground control have been well documented in papers presented at this conference too numerous to reference. Cable bolts have proven effective over the years mainly utilized in the form of supplemental support. Some limited work has been conducted on the use of cable bolts as primary support This work has been mainly confined to the West and the bolts utilized were of a non- tensioned type MSHA requirements for primary support have been that the bolt system he tensioned or if non-tensioned, then fully encapsulated with resin. Many operators are now interested in using cable bolts as primary support Further, despite the enormous success of cable bolts, there have been questions raised about the longevity and corrosion characteristics of the cable itself particularly for long tern applications. To improve the corrosion characteristics of cable bolts, galvanized cable has been used for some applications However. although improving the corrosion resistance of cable, galvanized cable for mine ground control does not provide complete protection under certain types of situations and mine environments. Realizing a need for a cable bolt that can be used for primary support and provides consistent installed tension, complete corrosion protection, and a fast installation, Keystone Mining Services. LLC (KMS), an affiliate of Jennmar Corporation, has developed the INSTáL CableOx system. This paper will detail the development and specifics of this system including two underground case studies

Jan 1, 2000

By David F. Gearhart

The Burrell Can1 is a thin, steel, tubular shell filled with aerated concrete that is used as a roof support in coal mines. The Can height is always shorter than the mining entry, so it is capped with wooden timbers and wedges when it is installed. This combination of the Can and the wooden header is a standing support system that is designed to yield in a controlled manner and exhibit a constant yield, or elastic-plastic behavior. The Burrell Can is capable of withstanding 20 in or more of vertical convergence and 15 in or more of horizontal displacement. Because of this exceptional ability to sustain load through extended convergence and displacement, it is one of the most robust standing supports in use today. The National Institute for Occupational Safety and Health (NIOSH) conducted testing on seventeen Burrell Cans in 1995, during development of the support where the ratio of the height to the diameter, or the aspect ratio, was between 2:1 and 4:1. Based on the results of that testing, it was suggested that the standard aspect ratio of the Can be less than 5:1. This suggestion is intended to preserve the overall stability of the Can, which will help to maintain the initial stiffness and prevent load shedding. Recently, the necessity of the aspect ratio has been questioned, and this issue will be addressed in this paper. Since the initial development and introduction, more than 130 tests of the Can have been conducted at the NIOSH Mine Roof Simulator (MRS), and 25 of those specimens had aspect ratios greater than 5:1. The 18-in-diameter by 10-ft-tall specimens had the largest aspect ratio, 6.67:1.However, the aspect ratio is not the only parameter that affects the performance characteristics of the Can. Multiple factors, such as the use of different wood species, the use of different header or footer configurations, and the use of pedestals, as well as biaxial loading conditions can also decrease the stiffness and capacity of the Can. Data from full-scale tests that include these other factors are analyzed to show that the initial stiffness is primarily affected by the roof and floor contact configurations. Furthermore, load shedding is more likely to occur or begin earlier when the aspect ratio is greater than 5:1 and one or more of the other factors are present.

Jan 1, 2012

By Winston Gale

This paper is presents a summary of recent investigations into fracture and caving about longwall panels. The results of these investigations indicate that rock failure initiates well ahead of the longwall face. Rock fracture typically forms in response failure through the material and bedding planes. Tensile fractures also form in massive units. These fracture patterns typically create a fracture network which determines the caving characteristics encountered at the faceline. The action of longwall face supports under such conditions is to maintain confinement to the fractured ground and develop a consistent caving line, The confinement developed above the canopy under these conditions can be variable on a shear by shear basis and the operational face support procedures play an important role in stability about the face area.

Jan 1, 2004

By Tristan H. Jones

Beginning in 1987, miniature dataloggers approved by the Mine Safety and Health Administration (MSHA) were publicly available for sale. The principal among these was the model CR21XQM, manufactured by Campbell Scientific, Inc. These dataloggers had been tested and were deemed permissible by MSHA and thus could be installed in the return air of an underground coal mine. In 1996, production of all permissible Campbell Scientific dataloggers ceased due to lack of sales. Data collection with these dataloggers has been a staple of ground control research in the United States for decades, and, without them, or a replacement, the capability to monitor ground behavior is severely impacted. Since that time, any party requiring a permissible datalogger has needed to borrow one that was purchased during the production years. In order to fill this technology gap and ensure its own data-gathering capabilities, the National Institute for Occupational Safety and Health (NIOSH) has developed and refined its own miniature data acquisition system (MIDAS). On February 16, 2010, MSHA deemed the MIDAS to be permissible and approved it for use in the return air of an underground coal mine. The MIDAS is an intrinsically safe, 16- or 24-bit datalogger, compatible with a wide range of resistive, single-ended, and differential-type instrumentation. It contains enough data storage memory to operate for over a year with typical data rates and is efficient enough to do this on a single C-sized alkaline battery for that entire period. It is menu-driven and requires no programming knowledge to operate. It supports wireless or hardwired communication for datalogger setup and data download. This paper describes the design, field and laboratory testing, and capabilities of the MIDAS datalogger. While not as fully -functioned as the CR21XQM, it is the only new permissible datalogger available, and there is intent to make it available to the mining industry for purchase.

Jan 1, 2012

By Vincent A. Scovazzo

The Pennsylvania Joint Coal and Gas Committee Gas Well Pillar Study of 1956 is the bases for well protection pillar design in the US and many other countries. An update was necessary because the well construction common to the gas and coal industries as well as mine configurations, mine depth, and extraction thickness have changed considerably since 1956. As initially envisioned the update would involve a similar empirical study that formed the basis of the initial investigation. However, there are no records of any gas or oil well failures related to coal mining since 1956 when mines followed the initial recommendation, making an empirical study problematic. Thus, the study had to be more analytical, which in return required at least some fundamental research into the behavior of the interaction of coal mining and oil and gas wells. A call to industry about research they have undertaken resulted in obtaining excellent research on the subject from three companies; Alpha Natural Resources, Inc., CONSOL Energy Inc., and Range Resources. These research projects were initially undertaken for internal use and not previously published. John T. Boyd Company reanalyzed these studies and determined how their results would affect protective pillar designs. These research projects pointed to the importance of horizontal movement and shear caused by subsidence and the strength of pillars and their foundations. The importance of geology is important in understanding horizontal shear, ground movement, and floor strength. The failure modes of casing and pipe needed to be understood so the threshold of these movements and stresses could be determined.

Jan 1, 2013

By Samrat Mohanty

The construction of underground hydrocarbon storage caverns in Jurong Island, Singapore, is nearing completion. The facility, located beneath the seabed of Banyan Basin, is comprised of five storage caverns with a storage capacity of approximately 1.5 million cubic meters. The galleries of each cavern are 20 m wide by 27 m high and approximately 340 m long. In addition to the storage caverns, various access and operations tunnels are required to support the facility. Among these are water curtain galleries to ensure that hydrostatic pressures in excess of hydrocarbon storage pressure are maintained in the rock mass surrounding the storage caverns. Early in the design process, conventional steel rock bolts with resin polymer grout were considered for ground control. However, the construction contractor proposed using fibe-reinforced polymer (FRP) bolts with cement grout due to the corrosive hydrologic environment, weight and handling considerations, local construction preferences, and the requirement to have a cavern design life of 50 years. FRP bolts with cement grout were ultimately chosen for the project. The FRP bolting system has proven to be very successful, with no ground failures experienced where systematic FRP bolting has been applied. This paper discusses the properties of FRP bolt/cement grout bolting systems, their characteristics in relation to steel bolt/resin bolting systems, and numerical modeling results assessing their performance.

Jan 1, 2014