Search Documents

By David C. Oyler

The Bureau of Mines conducted research at the 9-Right Section of the Olga Mine to determine the cause of bumps and aid in the development of appropriate control techniques. The purpose of this paper is to identify the factors which affect the occurrence of bumps at the Olga Mine. These factors have been broken down into two categories, in situ and mining related. The in situ factors include those conditions which exist prior to mining, such as variations in lithology and overburden, presence of jointing, the composition and the physical properties of the rock, and the original stress field existing in the coalbed and adjacent strata. The mining factors include the mining sequence, changes in stress in the coalbed and adjacent strata during mining, rates of convergence, and the pattern of failure of the coal and adjacent strata. The factors which appeared to have the greatest effect on bumping were the overburden, the lithology of the roof and floor rock and the physical properties of the rock. The roof rock is generally a massive, stiff sandstone which does not break until coal pillar extraction is complete. The immediate floor is a strong shale which generally grades into siltstone and then into sandstone. The overburden at 9-Right ranged from 990 to 1,600 ft. Secondary factors appeared to be the in situ (pre-mining) stress and the mining sequence. When barrier pillars were split., pressures measured in hydraulic cells (Borehole platen flatjacks) located in those barriers showed large pressure increases, and the incidence of bumps increased, especially when the barriers were near old gob areas. The pillar extraction system used at Olga, where three rows of pillars are mined concurrently, appears to reduce pillar loads at the face areas, thereby reducing the exposure of men and equipment to the risks of bumps during mining operations. The horizontal components of in situ stresses at Olga were found to be nearly the same as those at 5 other mines in southern WV, where humps were not common, so it appears that horizontal in situ stress alone is not a major influence on bumping at the Olga Mine.

Jan 1, 1987

By Yi Luo

Subsidence events occurred over inactive room and pillar (R&P) mines, including abandoned mines or sealed portions of active mines, are classified as unplanned subsidence because of their timing and distribution are unpredictable. When investigating such subsidence cases, many uncertainties exist and disputes often focused on whether the observed structural damages are caused by mine subsidence or other natural or artificial causes. However, solid evidences to identify the causes are often lacking. In order to conduct a thorough and impartial investigation, good knowledge in subsidence theories and other ground control subjects and broad experience are required.

Jan 1, 2009

By G. Bucelluni

An essential element of truss bolt installation requires machines to angle a hole in the top of approximately 39° to 45° from its vertical axis. Parameter which inherently effect the drill position are: height, width of truss, physical size of mast, and whether single or dual mast bolting is utilized. The combination of these facets govern the installation procedures required for the bolting cycle. The following illustration with written explanation will demonstrate this concept. See Figure #1. [ ] This model assumes certain fixed criteria which corresponds to a dual mast drill design and a set 41° drill angle. Using the derived formula, the maximum possible seam height for both masts to touch the bottom can be calculated for any given condition by substituting by the appropriate bolt spread distance. [ ] In a high seam application where the mast touching the bottom was considered a requirement, the proposed model demonstrates the advantage of single mast drilling. See Figure #2. [ ]

Jan 1, 1982

By Tim Ross

Slurry injection into mined-out panels is an attractive alternative for disposal of coal preparation plant fines. however, in areas where surface subsidence cannot be tolerated, either by law or necessity to protect surface structures or aquifers, special consideration trust he given to the effect of slurry injection on panel stability. Slurry injection can lead to panel failure and unplanned subsidence by degrading roof, pillar, and floor strength. Water degradation is of particular concern where clay is present in the floor. Recently. unplanned subsidence related to slurry injection occurred at an Indiana room-and-pillar coal mine subject to weak floor conditions. This paper discusses the efforts of the mine operator to determine the causes of the panel failure and to design panels and injection procedures to allow for future economic slurry injection without subsidence. The numerical and empirical/analytical techniques applied give the operator a rational approach to pillar panel design for future injection panels under various cover depths and weak floor conditions.

Jan 1, 1998

By Erdal Unal

In gate roads where supports are subjected to dynamic loading four times due to retreating longwall panels, it is a real challenge to replace the rigid arches with flexible reinforcement systems and yet to provide safety and stability of these openings within better economical limits. The results presented in this paper are based on a three years of research project aimed at developing safe and economical support systems for gate roads in Çayìrhan coal mine. Çayìrhan -Mine Project includes laboratory and field studies, design analysis, pilot scale design applications and performance monitoring. Based on outputs of the design approach developed, four types of bolts, namely, Split Set, Yielding Super Swellex, Sis-Resin, and Fosroc-Resin bolts were installed in a gate road together with widely spaced yielding steel-arches. In order to compare the performance of these flexible support systems and to provide feed back for the design approach, a monitoring program was initiated.

Jan 1, 1993

Virtually all mineable Appalachian coal seams exist in a multi-seam environment. This makes it inevitable that most seams will eventually experience interaction induced ground control and mining problems. Indeed, it has been estimated that every working face will experience interaction effects from previous or current workings at least once during its lifetime (1), and that these problems are considerably exaggerated when seams are in close proximity -- a distance of less than 110 feet. The continued increase in multi-seam problems has resulted in considerable research activities over many years (2,3,4,1). Theoretical analysis, numerical and physical model studies, statistical and empirical analysis of numerous interaction related field data have been applied to multi-seam mining situations and have identified many useful trends and design criteria (4,5,6,7). To fully utilize research results and transfer multi-seam mining technology to field engineers, a design model -- USEAM was constructed (8). This model, designed for close seam under-mining situations, was computerized to facilitate utilization. In the current research, a new computer program "MSEAM" was developed to produce a model for both under- and overmining close seam situations. It is hoped that both of these software packages will aid field engineers in using important interactive design criteria to gain a better understanding of interaction mechanisms. Through advance planning with these programs, detrimental interaction may be avoided and minimized, and occasionally a design can be selected which will allow interaction effects to be utilized to the benefit of mining operations.

Jan 1, 1987

By Kot F. v. Unrug

In spite of the extensive research and accumulated experience from mining operations, an appropriate pillar design remains an open issue. Due to the shrinking reserve base, present mining operations move to more challenging conditions. There are usually thinner seams and geologic conditions are often unfavorable. For instance, mine roof and floor are weak or deteriorate rapidly when exposed to moisture fluctuations in mine atmosphere. It is common that pillars of current operations are more- squat than several decades ago when the bulk of pillar research have been carried out in thicker seams. The methods of pillars calculations were developed regionally (in particular countries) to suit design needs for the most important seams, from which the majority of coal production was coming (e.g. Pittsburg or Pond Creek seams in the eastern of US). Most of the pillar formulae use similar approach by assigning weights (using constants) to the influence of coal (seam) strength and pillar widthheight ratio on its final strength. That mechanistic approach has sound theoretical base and good data supporting its validity. However, what seems to be missing is a qualification system of the mine conditions, which are outside of the data base or do not comply with the theoretical model applied in pillar strength formulae. This paper attempts to address that issue in two major categories, first when only a drill core data are available, and second during the mine development observations can be made directly on a coal seam. The composition of a coal seam is also addressed, (which often changes rapidly across the reserve), and discussed its influence on pillar's structural performance. In summary a set of practical design rules is presented.

Jan 1, 2005

By Miklos D. G. Salamon

If all stratifications are horizontal, the computation of surface deformation induced by coal mining involves the prediction of roof and floor convergence and then the transfer of the effects of this relative displacement to the surface through the use of the appropriate influence functions. A laminated model, in the form of a quasi- continuum, provides a simple means of computing the approximate convergence distribution and leads to the Gaussian distribution as the influence function. The ideas presented in this paper represent a subtle but fundamental generalization of the influence function Method. It is postulated that the influence of a small area of extraction is proportional to the roof and floor convergence and not to the thickness extracted. This difference in definition removes many conceptual difficulties associated with the influence function method. To demonstrate the utility of the model, the surface disturbances induced by the extraction of a parallel sided long panel are derived. Formulae giving subsidence, tilt, horizontal displacement and strain are given.

Jan 1, 1989

By Deren Zhu

Based on the results of in-situ observations and physical model analysis, a computer simulation method, FEAEBP, has been developed to predict the behaviors of main roof breakage in longwall mining by considering it as a Kirchhoff plate on Winkler elastic foundation. This method in used to investigate the initiation, and development of the breaking process of main roof and its displacement field before and after its breakage. In this paper the simulation method is introduced, characteristics of the displacement field of the main roof is discussed and monitoring variation of the displacement field of the main roof in a Chinese longwall face is demonstrated.

Jan 1, 1989

A procedure fm the estimation of pilla1 strength is presented where the design of underground coal pillars is emphasized. An analytical approach has been developed, proposing that the effect of end constraints on the pillar strength and the ductile behavior of coal material should be incorporated in the computation of the stability of coal pillars. Bad on this approach, it has been found that end constraint has a significant influence on the pillar strength. The study indicates that when the end constraint is zero the computed strength of the pillar is the same as the unconfiied compressive strength of the coal mass and will not increase with the increase in the width to height ratio. However. when the end constraint is greater than zero the pillar strength will increase exponentially as the width to height ratio increases.

Jan 1, 1990

By Wm. Mark Hart

Under a specific geological condition, roof supporting method, and pillar-entry system, an entry convergence concept may be the most effective means that can be used to effectively indicate the longwall entry stability (i.e. pillar bumps, roof falls, or floor beaver This concept may also be used to verify the effectiveness of the current pillar-entry system and roof supporting method. Furthermore, convergence measured under different mining phases may lead to a better understanding of the longwall mining-induced abutment loads and may be used to estimate stress change in pillars and thus pillar stability. In this paper, a remote entry activity monitoring system was designed; a comprehensive entry convergence monitoring strategy was proposed; thee abutment loading phases in longwall mining were defined; the relationship between roof deflection and stress change in a pillar was derived, and finally the extent and magnitude of the mining-induced abutment loads as well as their impact on entry convergence were discussed using the field data obtained so far.

Jan 1, 1995

By Denise Y. Dixon

The objectives of this study were to (1) document the hydrologic impacts of longwall mining on ground water, (2) identify the factors which affect the extent of dewatering, and (3) develop empirical trends to predict the extent of dewatering and recovery in advance of mining. The study was confined to three mine sites in north-central West Virginia. At each site, available ground water supplies were identified and monitored for dewatering effects and recovery. Mine A, located in Upshur County, West Virginia, has relatively thin overburden (approximately 715-280 feet). At this site domestic water supplies and specially constructed monitoring wells were monitored, continuing with an earlier study done by Cifelli arid Rauch. Most such supplies were completely dewatered over the longwall panel. Some of these wells have shown significant recovery, especially near a stream. Extensive monitoring of two nested piezometer wells revealed that dewatering generally started in advance of undermining in the lowermost monitored overburden zones first and then progressed upwards. Most dewatered wells completed in bedrock have shown no recovery, except. for valley drilled wells located within 100 feet of a Stream. Affected dug wells completed in valley alluvium rend located within 200 feet. of the nearest stream have shown significant recovery. Some wells have partially collapsed following mine subsidence. Mine B, having relatively thick overburden (approximately 585 to 900 feet), is located in Monongalia County, West Virginia. Ground water supply surveys have been conducted there in an attempt to study past dewatering effects. Owners reported Chat several wells were dewatered by longwall mining arid vertical air shafts that preceded longwall mining. Dewatered wells over longwall panels hove shown some recovery within 3 ½ years of mining. Mine C also has relatively thick overburden (approximately 585-900 feet), and is located mostly in Greene County, Pennsylvania. In addition to a survey of domestic water supplies at this site, five specially constructed monitoring wells were tested. The shallow monitoring wells suffered drops in water level due to mining but totally recovered within one day to three weeks after dewatering occurred. However, they did occasionally exhibit partial collapse during mine subsidence. Subsidence fracturing was beneficial in increasing the lateral hydraulic conductivity by a factor of about S to 22 for rock strata located within 124 feet of the surface, indicating enhanced shallow aquifer potential. One deep well suffered both partial dewatering and structural damage, with the state of water recovery bring uncertain. Also, two shallow domestic supplies out of five located over the mine were reportedly dewatered, but this claim could not, be substantiated.

Jan 1, 1988

By W. G. Pariseau

A crown pillar cave occurred at the Ropes Mine in December, 1987, that resulted in closure of the mine. Production was resumed soon afterwards with the formulation of a rock mechanics plan designed to address several issues of safety and stability. The plan proved to be successful and shows what can be accomplished in the realm of applied rock mechanics where a cooperative atmosphere exists.

Jan 1, 1989

By Ebrahim Ghasemi

Problem statement: One of the most challenging safety problems in room-and-pillar coalmines is controlling roof falls during retreat mining. Roof falls not only cause both fatal and non-fatal injuries to miners, stoppages in mining operations, and equipment breakdowns, but also results in the inefficient recovery of coal reserves. Approach: Sufficient awareness of effective parameters related to roof falls is an important factor in roof control. In this study, the major contributing parameters on roof falls during retreat mining are introduced based upon experience and judgment acquired from extensive retreat mining case histories and a review of relevant literature. Key findings: The main roof fall parameters in retreat mining can be divided into three categories: geological, design, and operational. Key conclusions: The design and operational parameters can be controlled by the engineer and/or operator. By the appropriate selection of these parameters in the design and implementation stages of retreat mining, the roof fall risk can be decreased to an acceptable extent.

Jan 1, 2012

By Jian Wu

In this paper, the surrounding rocks and the supports in a longwall are taken as an integral, i.e. a system. The structural characteristics and behavior of the system are discussed based on in-situ observations. A set of equations, which describe the interaction among the support, immediate roof and main roof, are developed. These equations can be used to design the longwall powered supports more reasonably and economically.

Jan 1, 1989

By John C. Stankus

The 3 Right pre-developed longwall recovery entry at Signal Peak Energy?s Bull Mountain No. 1 mine was designed to prevent the abnormal roof conditions encountered in its firsttwo recovery entries. Unique geological conditions, such as the low overburden of approximately 200 feet and prevalence of roof joints in the sandstone overburden, contribute significantly to abnormal conditions during longwall recovery. The 3 Right recovery entry was 42 ft wide and developed in two stages, 21 ft wide in each stage. The entry roof was reinforced with steel wire mesh/non-metallic recovery mesh, high-capacity primary bolts and cables. After all the support was installed, the entry was completely backfilled with specially designed, cuttable, low-density cement. The roof bolting and backfilldesign were based on current practices in this mine and successful practices in other mines in the U.S. and Australia. Extensive instrumentation was installed in the recovery entry for continuous monitoring of load transfer as the face approached and cut into the recovery entries. The support design was completely successful with a smooth cut-through on January 29 and 30, 2014, significantly reducing the shield recovery time and meanwhile protecting the safety of miners. Based on actual observance and practices of the 3 Right recovery entry, recommendations on improvement and modificationsof roof support for 4 Right recovery room are presented.

Jan 1, 2014

By Takashi Sasaoka, Pinyo Meechumna, Hiroshi Takamoto, Pipat Laowattanabandit, Akihiro Hamanaka, Kikuo Matsui, Hideki Shimada

"The EGAT Mae Moh coal mine is an open-cut coal mine in Thailand that produces about 16 million tons of lignite annually to generate 2,400 mw of electricity. The surface mine pit covers is 4 by 7 km (2 by 4 mi) with mining depths ranging up to 260 m (853 ft). A large pit slope is formed with the progression of the mining operation. However, massive slides in the pit slope often occur due to weak planes, such as faults and bedding, and the weak mechanical properties of the rocks. Hence, a 200-300 m (656-984 ft) boundaries of rock block including coal seams is left in front of faults in order to prevent slides and maintain the stability of the pit slope. As a result, there are significant coal reserves beneath the abandoned area along the pit slope.The focus of this paper is on the applicability and design of the highwall mining for recovering much of the coal left along the pit slope.INTRODUCTIONThe EGAT Mae Moh Mine is located about 630 km (186 mi) north of Bangkok, Thailand (see Figure 1). It is the largest coal mine in Thailand and produces about 16 million tons of lignite annually from open-cut mining (70 % of the total coal produced in Thailand). The coal is used to generate 2,400 mw of electricity at the Mae Moh power plant, which is situated near the mining area. The mine pit covers an area of 4 by 7 km (2 by 4 mi) at varied depths up to 260 m (583 ft) as shown in Figure 2. As the mining operation progresses, the pit becomes to be deeper and deeper. In the year 2035, the bottom of the pit is expected to reach depths of 500-600 m and the open-cut mining operation will be finished. The possibility of an underground mining operation is being investigated.A large pit slope is formed with the progression of open-cut mining. However, massive slides often occur in the pit slope along weak planes including faults and bedding planes due to the weak nature of the rock. As a result, 200 to 300 m (656 to 984 ft) boundaries of rock including coal seams are left in place in front of faults to prevent slides and to maintain the stability of pit slope. Moreover, the dip of the slope is less than that of the planned design. As a result, there significant coal reserves abandoned along the pit slope."

Jan 1, 2010

By Guorui Feng, Min Zhang, Yi Luo, Jian Yang, Yujiang Zhang, Junwen Bai

"Safe mining of coal seam sandwiched between abandoned upper and lower room-and-pillared mines (ULPM) ·is increasingly becoming the focus of attention in recent years, which is closely related to the damage intensity of the upper and lower interburdens. The #7 seam with ULPM in Baijiazhuang coal mine was selected for this research. According to the mining and geological conditions, the vertical stress and plastic zone distributions were determined first by numerical simulation. Then, a theoretical model based on the elasti-plasticity theory was developed. The stress distribution and failure zone created in the interburden by mining the upper and lower seams were determined. Finally the feasibility of mining #7 seam between the abandoned upper and a lower seam was evaluated. The results show that: (1) the distributions of abutment pressure and plastic zone coincide, both of which can be used to evaluate the failure zone in ULPM. The failure zone penetrates the whole upper interburden, while only parts of the lower interburden fail. (2) the theoretical failure zone coincides with the maximum distribution zone of abutment pressure and plastic zone obtained by numerical simulation: the failure zone height in the lower interburden is less than its thickness, while that in the upper interburden is larger than its thickness. (3) the #7 seam is located in the failure zone created by the upper seam room-and-pillar mining, which leads to well-development fractures and blocky fragments in the roof, thereby it is unstabled. (4) when mining the #7 seam in the interburden, the key is to control the roof strata and proper support measures should be taken timely to ensure safe mining.INTRODUCTIONMany coal mines in China mine the thick, superior and easily mineable resources preferentially, while the thin, inferior and difficult-to-mine resources were abandoned (Chappells and Trentrnann, 2015; Zhenfu, 2012; Xu, et al., 2015; Guorui, 2009). As the results of deficient geological data and shortage of investment capital, the residual coal resources distributes in many mining areas in China.In recent years, many residual coal seams sandwiched between the abandoned upper and lower room-and-pillar mines (ULPM) were explored in Shanxi Province, especially in the mining area of Datang, Xishan and Luan (Figure.1). The reserves of residual coal seams in ULPM are considerable, increasingly becomes the focus of attention among scholars and engineers."

Jan 1, 2016

By W. M. Pytel

The applicability of the beam theory in analysis of roof- pillar-weak floor interaction in partial extraction room-and-pillar mining is presented. The mine structure is modeled as an equivalent multi-indeterminate overburden elastic beam supported by elasto-plastic pillars; resting on a viscoelastic layer of immediate weak floor strata underlain by a competent rock mass. The developed analytical model was initially utilized to conduct sensitivity analyses of different variables affecting the mining system, such as the deformability of coal and weak floor strata, thickness of weak floor strata, number of pillars in a panel, width of pillars, width of panel etc. These analyses were then extended to three overburden strata - coal pillar - floor strata lithologies typical of active coal mining areas in Illinois.

Jan 1, 1989

By Ihsan Berk Tulu

The complex interaction between multiple seam pillar extraction panels and variable topography can generate unexpected ground control problems. This case study describes stress-related damage in multiple seam workings that resulted in difficult operating conditions and compromised the safety of the support crews. The damage appeared to be caused by horizontal stress but the unexpected location of the damage baffled the authors. A 2D Finite element analysis was conducted of the mine layout and surface topography in an attempt to explain the observed failure. It was discovered that the topography resulted in the rotation of the major stress at the location of the current workings. The stress rotation caused asymmetrical interactions between the workings on the different coal beds, which can explain the unexpected response observed in the mine. Consequently the layout of the next panel was changed by locating the vulnerable entry 30 ft away from its originally planned position. The new location was selected to locate the entry in favorable stress conditions. The change in layout resulted in a significant improvement in conditions when the next panel was mined. At the time of writing this paper, a full panel has been developed using the modified layout without undue ground control problems. The case study demonstrates that numerical models can help engineers to interpret and solve complex multi-seam interaction problems.

Jan 1, 2014