Search Documents

By J. R. Koehler

Although two-entry yield pillar-based gate roads supported by wooden cribs have been commonly used throughout longwalling in the Wasatch PlateadRoan Cliffs coalfield of central Utah, a three-entry yield-abutment gate road configuration was recently trialed in the Hiawatha Seam at the Genwal Resources (GRI) Crandall Canyon No. 1 Mine, near Huntington, UT. Pillar, entry, and cable bolt performance were monitored through second panel mining using a fairly extensive array of geomechanical instruments installed over a span of four crosscuts. Ground pressure and entry closure measurements confirmed that the 9.1-m-wide (30-ft) yield pillar was partially shielded from first panel longwall loads by the 36.6-m-wide (120-ft) abutment pillar, and consequently, experienced only minor yielding until the approach of the second panel face. Complete yielding of the 9. I-m-wide (30-ft) pillar occurred when the second panel was approximately 6.1 m (20 ft) inby the instrumentation site. Average cable bolt loads and differential roof sag remained low through second panel mining and tailgate entry ground conditions were excellent; however, very high ground pressures in the abutment and yield pillars, and second panel rib strongly suggest a high potential for coal bumps utilizing this gate road configuration at mining cover depths in excess of 396 to 457 m (1300 to 1500 ft). This conclusion is supported by the suspected occurrence of small coal bumps along the abutment pillar ribs, observed indirectly as fresh debris in the middle entry just behind the second face. This paper presents a case history developed from the geotechnical measurements and on-site observations of this unique application of a yield-abutment gate road configuration and cable support system in the Hiawatha Seam.

Jan 1, 1996

By Vincent A. Scovazzo

"The most significant study on the effects of longwall mining on gas and oil well integrity was completed by a consortium of coal and shale gas industry participants. A field study was conducted in 2013 and 2014 and is referred to by its location on Well Pad NV-35. The experiment site was located at the CONSOL Enlow Fork Mine in Washington County, Pennsylvania.The experiment was completed to verify John T. Boyd Company (BOYD) calculations and studies completed under contract by for the Pennsylvania Department of Environmental Protection Gas Well Pillar Study Update. The findings of the original study were presented by BOYD at the 32nd Conference, while numerical analysis of the Well Pad NV-35 field study was presented by Dr. Su at the 35th Conference.This paper addresses the findings of the experiment and how it confirmed the conclusions of the original study.INTRODUCTIONA field study was conducted in 2013 and 2014 by a consortium of coal and shale gas industry members to test the effects of longwall-induced ground movement on the stability and integrity of wells drilled through a gateroad abutment pillar. The project was initiated to test initial John T. Boyd Company (BOYD) findings of the Gas Well Pillar Study Update (Scovazzo and Moran, 2014), completed for Pennsylvania Department of Environmental Protection, Bureau of Oil and Gas Management (PDEP). Background and initial findings on this project were presented at the 32nd Conference (Scovazzo and Moran, 2012). The field work and numerical analysis were spearheaded by CONSOL Energy, Inc. (CONSOL) with participation by Chevron, EQT, Noble Energy, Range Resources, Marcellus Shale Coalition, and the Pennsylvania Coal Alliance.Dr. Wen H. Su of CONSOL was the leader of the field experiment with input from the participants. Dr. Su also completed numerical analysis of the results and model casing deformation. Analytical results were presented by Dr. Su at the 35th Conference (Su, 2017)."

Jan 1, 2018

By Y. P. Chugh

About 60-70% of the underground mined coal in Illinois is extracted using a room-and-pillar mining method that permits extraction of about 50% of the coal. The remaining coal is left behind in the form of support pillars to control surface and subsurface movements. Illinois coal seams are typically associated with water sensitive weak floor strata whose thickness varies 0.31 - 1.3 m. The current mining geometry mostly uses pillars of constant size within a mining area. This traditional practice suffers from the disadvantage that pillars within the center region are subject to much higher loads than the pillars located on the outer edges of the panel. This results in a higher incidence of rib spalling, and roof falls, creating a potentially hazardous work environment. In addition, this concentration of loading at the center of the panel provides initiation points for floor failure to occur. The primary goal of this study was to reduce ground control problems and production costs in Illinois mines by considering alternate mining geometries. The development and subsequent field demonstration of an alternate geometry is presented in this paper.

Jan 1, 2004

Continuing with the effort of providing new and more effective exploration methods to the mining industry, where direct methods (drilling, cross-cutting, etc.) are not applicable, either for logistical or environmental reasons or because they are costly and sometimes ineffective, we present here a new seismic technique based on full wave recording of 3-D channel waves generated within the coal seam across a longwall. In the past two years we reported the application on In-Seam High Resolution Seismic Reflection (ISHRSR) and In-Seam Seismic Tomography (ISST) to map non-coal inclusions that disrupt the coal seam continuity. In the present paper we present a 3-D In-Seam Seismic Tomography (3-DTSST) method using 3-D channel waves recorded by three component high resolution geophones. The method allows to distinguish longitudinal and transversal components of the channel waves, similar to the spheroidal and toroidal modes for the free oscillations of the earth. The recording of these waves allows a more complete analysis of the free modal vibrations of channel waves, permitting a more complete inversion of the structure of the coal seam through which they travel. The full wave analysis provides additional insights of the detailed coal structure for larger, distances than for the ones previously reported using the one dimensional method. The refinement of the inversion software is also a contribution towards the better definition of the coal seam geometry and structures disturbing them such as sandstone channels, sandstone rolls, partings, mine voids, faults, fractures, etc. The method is illustrated with three case studies where subsequent mining revealed the virtues and limitations. The first example deals with the problem of mapping mine works in one side of a longwall panel which geometry is well known, to verify its applicability to map old mine works. The second example deals with a sandstone body that partially scoured the coal seam withing a longwall panel. The third shows an application of the method to map roof conditions in a longwall panel where this problem critically affected production scheduling and costs

Jan 1, 1996

By Doug Tesarik

Researchers from the National Institute for Occupational Safety and Health1 (NIOSH), together with employees from The Doe Run Company, are monitoring and evaluating the stability of a pillar retreat section at the Fletcher Mine, a lead/zinc, room-and-pillar mine near Bunker, MO. Cemented rockfill is being used to provide roof support as high-grade, remnant ore pillars are mined. Earth pressure cells and deformation meters placed in backfill panel pillars monitor stress change and vertical deformation, respectively, as nearby ore-bearing pillars are extracted. Similarly, biaxial stressmeters and borehole extensometers are used to monitor mining-induced stress change and deformation, respectively, in long-term support pillars. Data from these instruments indicate that when ore-bearing pillars were mined, stress was redistributed from support pillars to a backfill panel pillar. The data also indicate that the backfill and support pillars have remained stable for two years after pillar extraction was completed in the area. This research demonstrates the importance of using reliable instruments to document the geomechanical behavior of pillars and backfill. Gaining a better understanding of roof support and stress redistribution mechanisms is a fundamental part of NIOSH's goal to reduce and/or predict rockfalls, which are still among the leading causes of injuries in metal/nonmetal underground mines.

Jan 1, 2006

By William J. Schloemer

INTRODUCTION The history of coal mining the Ostrava Region of the Czech Republic goes back nearly 250 years. Both coking coal for steelmaking and thermal coal for the production of energy are mined here; however, it was the coking capabilities that subsequently turned the region into a major steel-producing area in the early 1800?s, something that continues to this day. Ostrava lies in the northeast corner of the Czech Republic, near the southern border of Poland, and falls within the Upper Silesian Coal Basin. The region contains over 400 seams of coal of which about 150 have been mined over its history and continue to be mined. Eighty percent of the Upper Silesian coalfieldlies in Poland and is presently mined by about 35 coal mines; the remaining 20% falls in the Czech Republic, which presently has four mines operated by OKD, a.s., a subsidiary of Amsterdam-based New World Resources. Traditionally, all the mines in this region have employed the longwall method of mining, of which subsidence is an unavoidable consequence. In fact, due to the long history of longwall mining here, there are areas where the overall subsidence has exceeded 37 meters (121 feet). The region is fairly densely populated with residences and industry, and a considerable amount of coal lies under some of these areas where subsidence is not allowed or has to be minimized. It is this reason that has driven OKD to consider alternate methods of mining that will not create subsidence. The decision was made to consider the room and pillar method of mining in order to leave stable pillars of coal to support the surface. After considering several locations, OKD chose the shaft safety pillar at the CSM mine as a test mining location. To say the least, this is a very challenging location in which to conduct a test. As with the entire region, there are many faults from tectonic activity, the seams are pitching at 12 to 20 degrees, the area is affected by high horizontal stress, and the depth of 750 to 900 meters is perhaps the deepest room and pillar coal mining ever attempted.

Jan 1, 2014

By John L. Edwards

The underground coal mines in the Lake Macquarie area of the Newcastle Coalfield, New South Wales, Australia are constrained by surface subsidence restrictions as low as 150 mm. The mining environment is shallow, generally between 100 m and 200 m, often multi-seam and commonly overlain by residential development or tidal waters. Most mines use partial or panel and pillar extraction techniques to meet the subsidence restrictions and allow maximum resource recovery. This paper gives an overview of the results of a recent two year government funded research project aimed at developing a mechanistic, geomechanically based mine design criteria for subsidence control. Three extraction layouts were monitored in detail to assess the relationship between mining geometry, pillar behaviour and surface subsidence. Pillars at each site were instrumented with stress cells, convergence monitors and extensometers. Field data was used to initially calibrate, and subsequently, verify stress and displacement predictions made by the three-dimensional displacement discontinuity code, SUBSOL. Back-analysis of the modelling results indicate SUBSOL's capability as a tool to satisfactorily predict surface subsidence magnitudes and pillar loads for alternative pillar and panel layouts.

Jan 1, 1993

By David A. Newman

In the 1950s, an underground limestone mine in the Camp Nelson Formation was developed from an outcrop exposure. The Camp Nelson Limestone met the requirements for DOT stone and aggregate. The mine ownership changed several times, which resulted in distinct mine designs in Level 1. Based upon the production requirements and an attempt to maximize limestone recovery from a single level, a variety of pillar dimensions and three mining heights (28 feet, 68 feet and 83 feet) were developed. This was sufficient prior to reaching the mineable extent of Level 1. Level 2 introduced previously unknown ground control challenges. These included: ??Pillar spalling and a significant back fall on the Level 1 - Level 2 decline; ??Laminated immediate back and the need to bolt the back on Level 2; ??Delamination of the back adjacent to the Level 1 - Level 2 decline resulting in bolt shearing, and floor heave in isolated areas of Level 2; ??Multiple level interaction, the need to design pillars based upon numerical modeling as columnization between Levels is infeasible: and ??Water inflow as the mine approached river. To meet the challenges, a testing program to determine rock strength and physical properties was implemented along with numerical (LAMODEL and FEM) modeling, and borescope inspections of the immediate back. The efforts to implement rock mechanics were re-focused as Level 2 approached its mineable limit and the initial attempt to drive a decline to Level 3 was unsuccessful. A second decline site was selected based on inter burden stability, a consistent shale parting for the Level 3 back horizon, results from numerical models of the immediate back and multiple level interactions, and the projected low water inflow. The mine is operating on Levels 2 and 3 with long-term planning and ground monitoring for Level 3.

Jan 1, 2014

By Murali Gadde

U.S. coal mines? primary roof supports typically consist of passive resin bolts; however, the use of active bolt systems is increasing. Despite this widespread use, a comparative performance evaluation of these bolt systems has not been done under similar geologic conditions. The performances of three commonly used primary bolt systems were investigated: fully grouted passive rebar, fully grouted tension rebar (using two speed setting resin), and resin-assisted rebar with mechanical anchors. In order to investigate the performance of these bolts, strain gauged bolts of all three types were installed at three different coal mines as part of a larger research project funded by the National Institute for Occupational Safety and Health (NIOSH). This paper addresses the initial installation bolt loads measured at these mines. Analysis of the data showed much lower installed loads on active bolts than is traditionally assumed. It appears that the active load on bolts bleeds off relatively quickly under geologic and operational conditions similar to those at the studied mines. The data also showed that within a short time span after installation, the measured loads on active and passive bolts did not differ significantly. This paper compares the results from over 20 bolts of each bolt type that were all 1.8-m (6-ft) -long, 20-mm (0.804-in) nominal diameter Grade 75 rebar and discusses the relevance and shortcomings of the data and bolt performance.

Jan 1, 2011

By Ben Mirabile

Over the past three decades, the U.S. coal mining industry has widely used cable supports to supplement traditional primary bolting systems, especially in difficult ground conditions. However, increased mining activity in adverse conditions has underscored the limited effectiveness of the non-tensioned, partially grouted cable supports used to supplement primary bolts. Roof failures in conditions such as corrosive environments, highly laminated strata, low overburden depth and water intrusion have demonstrated that the need for cable technology has reached beyond the traditional non-tensioned, partially-grouted cable tendon. Furthermore, declining market conditions and increased competition for coal customers has demanded that new cable bolt technology be costeffective and readily adaptable to the mining cycle. Jennmar Corporation has developed several cable bolt technologies that can be used as stand-alone solutions or in concert with one another to mitigate adverse conditions. These technologies include rapid tensioning of cable supports, structural surface control and polyurethane injection. The case studies presented in this paper use one or more of these technologies to address adverse mining conditions or special ground control problems.

Jan 1, 2013

By C. C. White

Much benefit can be achieved by a mining company and a manufacturer if both parties can communicate effectively with each other and assist in product development; mutually beneficial ideas and products will develop. This communication can best be achieved if both parties have the opportunity of having on their respective staffs, specialists whose function is to improve the use of products used in mine development. Although a great wealth of roof control knowledge has long existed among mine operators, until recently there was not an abundance of joint development of roof control material by manufacturers and mine operators. This was perhaps due, in past lean years, to the preoccupation of mine management with other overwhelming problems that arise in mining. Manage¬ment had little time for the lengthy process of product development. Until recently, only a few of the largest mining companies had fulltime personnel devoted to roof control. A bolt manufacturer who is invited to work with an operator's roof control people in developing new material is lucky indeed in that he learns what is wanted and he acquires the benefit of the operator's knowledge and experience. He has only to come up with a satisfactory product at an acceptable price - which is not always easy: The development of new products is usually costly and time consuming, and many new products fall by the wayside. In the case of point anchors, however, this product is here to stay. The advantage of point anchors over mechanical anchors is now a proven fact. This advantage is due to less bleed off and higher ultimate load capacity of the resin point anchors. Point anchored bolts have proven to be superior to fully grouted bolts in many areas. We at Birmingham Bolt Company are fortunate in that we have been involved in joint efforts to develop point anchors with several coal companies from whom excellent advice and direction was received. It is appropriate to mention before continuing that the use of point anchors began in the 1960's in Europe and became widespread only recently in the United States. They fall in two categories, point anchors and combination point anchors. These categories have been defined by the Bureau of Mines as follows: (1) point anchors having 24" of grouted length and (2) combination anchors having 24" or more of grouted length. In the present nomenclature, all are anchored with resin or some sort of cementing compound between the rebar or tensioned element and the wall of the hole. The latest development includes an expansion shell as well as rebar, the purpose of the expansion shell being to facilitate installation without the delay necessary in use of types that require a waiting periond for setting of the resin before tightening. (See figures #1 and #2.

Jan 1, 1982

By Christopher C. Woomer

Cyprus Shoshone Mine uses the longwall method to extract a deep, thick, pitching coal seam in the Hanna Basin of South Central Wyoming. The immediate, and main roof rock consists of weak, thinly-bedded, silty mudstones with weak, interbedded fine-to medium-grained sandstone. Tailgate ground control has been a critical factor impacting productivity at the mine. A gateroad condition mapping program for the 11 left longwall gateroads indicated potentially severe ground control problems for the tailgate. It was predicted that the existing, secondary support pattern of wood cribs would not provide adequate support capacity. As predicted, severe deterioration of the tailgate occurred in the form of a roof cutter, sloughing ribs, and failing wood cribs. Productivity was affected and additional support was required. Shoshone personnel evaluated several options for providing the additional support needed in the tailgate. The additional support system and placement method had to satisfy several requirements with respect to access, materials handling, placement method, set-up time and support capacity. Approximately 6,000-ft. of deteriorating tailgate had to be supported. The initial wood crib support system left a 6-ft. walkway for access and construction of the additional support. This access was further reduced as the roof loaded the wood cribs. This eliminated the possibility of mechanized material handling to the construction locations. All materials would have to be transported by hand. The additional support system had to be placed quickly to stay ahead of, and keep pace with, the required longwall advance rate. It had to incorporate the existing wood cribs and provide at least 500 tons of extra support capacity. And most critically, the system could not affect longwall ventilation. Longwall coordinators and engineers made the decision to use a low density, pumpable cement known to the industry as TeksealTM, to provide the system required. A 200 psi ultimate strength mix was decided on to provide the required load capacity. The existing cribs were formed with 1-in. by 6-in. boards and brattice cloth to provide the containment. To overcome the access limitations, three boreholes were drilled from the surface to the tailgate on 2,000-ft centers. A mobile pumping station was established on the surface and the TeksealTM was pumped 900-ft. down the boreholes through a 1.5-in. steel pipe, then as much as 1,800- ft. along the tailgate entry through 1.25-in. miner spray hose. The materials required for the TeksealTM supports could all be carried into the construction locations by hand. As a direct result of incorporating relatively new methods of pumping high yield, low density, cementitious grouts, the Shoshone Mine reduced downtime due to tailgate ground control problems by approximately 70% in comparison with previous Longwall panels. The longwall set three monthly production records while mining the 11 left longwall under the deepest cover, steepest pitch, and most extreme ground control conditions ever encountered at the mine.

Jan 1, 1995

By Shuangsuo Yang

Based on field observations and physical modeling of simulated materials, the dynamic equilibrium principle on the whole interaction process between the surrounding rocks and support of large deformation roadways in coal mines has been developed. It explains the methods of forming the bolted strata and its changing load capacity with deformation. It also points out the factors and conditions for forming the bolted strata as follows: (1) many entries in coal mines are subject to large deformation. During their service life, it goes through the following process, elastic > plastic > fiacture > broken > loosening, etc. During this dynamic process, the mechanisms of supporting structure are changing and therefore the interaction between support and rocks experiences a process of dynamic equilibrium. Furthermore, the required supporting force for stabilizing the surrounding rocks shows overall decreasing trend; (2) the bolted strata is a special supporting structure consisting of bolt, rock skin protection devices and rock strata within the bolted horizon. As deformation increases, the supporting structure of the broken strata within the bolted horizon experiences a process of periodic change, from equilibrium > not equilibrium > equilibrium. Corresponding to this change, the supporting capacity of the bolted strata also fluctuates and gradually decreases; (3) under the bolted strata, the stability of a large deformation roadway is dynamic and step-wise; and (4) the formation of bolted strata, especially bolted broken strata depends on the existence of compressive force. Supporting the bolted strata is not constrained by the quality of the surrounding rocks. It has broad range of application.

Jan 1, 2005

By Ted Klemetti

Roof deterioration in weak moisture-sensitive rock leads to roof falls in coal mines. An observation site was set up in intake air at an underground coal mine in central Ohio to evaluate the time-dependent deterioration of moisture-sensitive roof rock. By periodically collecting and weighing the rock falling from the roof, the National Institute for Occupational Safety and Health (NIOSH) was able to quantify the deterioration of the moisture-sensitive shale roof. The measurements showed that more roof rock is falling in the dry winter months. Movements in an intersection were monitored in order to determine if deformation correlated with seasonal changes in temperature and humidity. The rate of intersection roof-to-floor convergence was found to be cyclical and related to seasonal changes, with more convergence during the months of April through September. At the study site intersection, the roof beam did not show deflection indicating movement most likely due to mine floor deformation. The bolt load also increased in the warmer months before shedding load, possibly due to rock failure. Temperature and relative humidity sensors, placed in holes in the roof show that mine air does not mix with the air in the holes. Consistent saturation levels of relative humidity were measured in the holes and it appears that high levels of moisture may have migrated into the bolt holes from roof shales. A roof sealant applied to a portion of the test roof appears to be preserving the roof and reducing the amount of rock fall into the entry, while the screened area virtually eliminated rock falling from the roof.

Jan 1, 2009

By Stephen P. Signer

A method to assist in the evaluation and selection of roof bolts using in situ measurements of roof bolt loading has been developed by researchers of the Spokane Research Center, National Institute of Occupational Safety and Health. Both axial and bending forces are measured by strain gauges at many locations along the length of fully grouted bolts during various stages of mining. This information is then used to ( I) predict bolt loading for variations in bolt spacing, grade, and diameter, (2) calculate the design changes necessary in zones where bending loads are high, and (3) determine if bolt length is adequate. Results from several case studies of full-column bolt loading in coal mine gate roads are used to illustrate the design method. This knowledge will give design engineers a tool for the selection of roof support systems that will improve underground safety by reducing roof bolt failures.

Jan 1, 1997

By Daniel W. H. Su

The importance of incorporating fundamental principles of rock material response and failure mechanics into a pillar strength design model has been demonstrated. To accurately assess pillar strength, a model should account not only for the characteristics of the coal, but also for those of the surrounding strata. The interactions between the pillar and the surrounding roof and floor dictate ultimate pillar strength. Confinement, or the lack thereof, provided by roof and floor frictional end-constraint is one of the most significant factors in the strength of very wide pillars. The best conditions for end-constraint occur with ideally strong roof and floor. In this paper, it will be shown that weak roof and floor may decrease the ultimate pillar strength by as much as 30% compared to ideal conditions. Field observations confirm this pillar strength reduction in the presence of weak roof and floor. Furthermore, rock partings within the coal have a variable effect on pillar strength, depending on the parting strength. A competent shale parting within the coal reduces the effective pillar height, thus increasing the ultimate pillar strength; a weak claystone parting slightly decreases the strength. Imposed load distribution also has a significant effect on pillar strength, such that asymmetric pillar loading, similar to that observed in pillars adjacent to high extraction mining, reduces the ultimate pillar strength below that of equivalent pillars subject to uniform load distributions.

Jan 1, 1997

By James Pile

Long, high capacity, highly tensioned, cable bolts (strand bolts), stiff enough to be installed with resin like a solid bolt, yet flexible enough to be used in any lengths, have been widely used in Australian coal mines since the early 1990?s. A brief history and update on recent developments of this technology is provided. The first major US trial of this Australian technology, has recently taken place at BHP Billiton?s San Juan longwall coal mine in New Mexico. Thirty-five foot long, high capacity, highly tensioned, post-grouted cable bolts are being used to provide active secondary support of intersections in areas where operator safety and life of mine considerations are paramount, and standing support cannot be installed for reasons of equipment access. The cable bolts are resin anchored into overlying sandstone channels, tensioned, and post-grouted. The installation procedure and support results for these highly tensioned cable bolts are given.

Jan 1, 2007

By Nic Slatalla

Acoustic emission monitoring techniques are a powerful tool for analysing deformation behaviour and fracture characteristics of rock samples under uniaxial loading. Uniaxial compression tests were carried out on three different types of sandstone for a better understanding of acoustic emission response with respect to rock deformation and damage develop-ment. All sandstone samples revealed congruent characteristic acous-tic emission patterns which correlated directly with distinct stress-strain stages. However, the acoustic response and development within the individual stages proved to be entirely different due to variations in their microstructure.

Jan 1, 2008

By Long Fan, Shimin Liu, Guijie Sang

"Weak shale roof falls have long been the main cause for fatalities in underground coal mines. Moisture-induced swelling is one of the root causes for the degradation of roof shales. In this study, slake durability tests are conducted on shale samples collected from Illinois basin coal mines, and different levels of durability are analyzed according to Gamble slake durability classification. There are two main mechanisms influencing the shape of retained fragments after two cycles of wetting and drying: mechanical abrasion and swelling pressure. A prototype optically based shale swelling apparatus is designed and manufactured for the shale free-swelling measurement. The experimental results suggest that swelling pressure tends to deteriorate shale laminations. Moisture-induced swelling of the No. 6 roof shale from Bear Run Mine was measured under 100% relative humidity condition. The measured swelling strain normal to beddings is ~5 to 7 times greater than the swelling strain parallel to beddings. This suggests that interlayer expansion plays a key role in moisture-induced swelling. Cracks induced by swelling pressure tend to occur along the bedding plane and lead to shale deterioration. INTRODUCTION Background Ground falls have long been the cause for nearly 50% of all fatalities in underground coal mines and continue to be one of the greatest safety hazards in underground spaces. Among the various ground fall hazards, roof failure takes up 23% of total fatalities in underground coal mines, of which 13% are due to skin failure and 10% are due to massive roof falls (Mark, Pappas, and Barczak, 2011). Roof failures associated with weak shales are summarized in previous studies (Molinda and Mark, 2010; Aughenbaugh and Bruzewski, 1973; Bajpayee, Pappas, and Ellenberger, 2014; Murphy, 2016). For mine roof instability and failure, two aspects can explain the failure mechanism of weak roofs. One is the elevated stress concentration in lateral direction due to the mining-induced excavation and its stress redistribution around the mine opening (Song and Stankus, 1997; Fan and Liu, 2017; Hill, 1986). The other mechanism is the passive stress-relief due to the strength weakening induced by the ambient moisture and temperature fluctuations during a period of time. Shale is moisture sensitive and presents a lower durability if it is exposed to a highly humid environment for a long time, thus leading to roof deterioration and instability in underground coal mines (Aughenbaugh and Bruzewski, 1976; Stateham and Radcliffe, 1978; Chugh and Missavage, 1981; Klemetti, Oyler, and Molinda, 2009). It is well known that shale is a clay-bearing sedimentary rock and that clay minerals are water sensitive. The moisture uptake for shale will induce the micro-deformation of a shale matrix, thus the structure and strength of shale is a function of time and intensity of moisture exposure. All mine engineers notice moisture-induced shale deterioration; however, the underlying mechanism(s) are still not fully understood due to the complexity of geophysical-chemical water-shale interactions (Huang, Aughenbaugh, and Rockaway, 1986; Hensen and Smit, 2002; Diaz-Perez, Cortés-Monroy, and Roegiers, 2007). The coal mining industry is still in the process of finding a technically sound, cost-effective technology to prevent this unexpected and unpredictable shale roof failure. Therefore, understanding how the moisture-sensitive shale responses to various ambient moisture and what role exposure duration plays in shale roof failure is key to prevent unexpected roof incidents, which will lay the foundation for the long-term roof support design and ground control management."

Jan 1, 2017

By Keith A. Heasley

Numerous different instruments and techniques have been developed for the purpose of measuring rock stress and stress changes around excavations. The interpretation of the output from many of these instruments has often been problematic. This paper covers the research performed in attempting to analyze one particular stress measuring instrument called the Borehole Platened Flatjack (BPF) . The approach used in this analysis was to combine the analytical solution for the displacements around a borehole and the analytical solution for the bore- hole-platen interaction with the empirical stiffness behavior of the flatjack. The resulting model of the BPF response was then verified using measured laboratory data with very good results. In addition, techniques for applying the method to the field are briefly discussed. The major accomplishments of this comprehensive modeling and testing program are; 1) the establishment of the critical installation and site parameters of the hydraulic pressure cell and 2) the development of a systematic procedure for calibrating the cell based on the given values of these critical parameters.

Jan 1, 1989