Search Documents

By Joseph C. Zelanko

Cable bolt support techniques. including hardware and anchorage systems, continue to evolve to meet U.S. mining requirements. For cable support systems to be successfully implemented into new ground control areas, the mechanics of this support and the potential range of performance need to be better understood. To contribute to this understanding, a series of 36 pull tests were performed on 10 ft long cable bolts using various combinations of hole diameters, resin formulations, anchor types, and with and without resin dams. These tests provided insight as to the influence of these four parameters on cable system performance. Performance was assessed in terms of support capacity (maximum load attained in a pull test), system stiffness (assessed from two intervals of load-deformation), and from the general load-deformation response. Three characteristic load-deformation responses were observed. An Analysis of Variance identified a number of main effects and interactions of significance to support capacity and stiffness. The factorial experiment performed in this study provides insight to the effects of several design parameters associated with resin-anchored cable bolts.

Jan 1, 1995

By Kevin J. Ma, John Stankus, Dakota Faulkner

"Expandable rock bolts are widely used in hard rock mines as an efficient ground control product. However, capacity and service life can be significantly reduced if the metallic body is subjected to corrosion. In some hard rock mines in the U.S., highly corrosive ground conditions exist, and it has been reported that inflatable rock bolts have corroded within a few months after installation. To provide mining industry a cost-effective inflatable bolt and combat the corrosion issues, Jennmar Corporation, Inc., and its subsidiary Keystone Mining Services, LLC (KMS), analyzed corroded bolt samples, identified root causes, evaluated properties of various coating materials, and developed a new inflatable rock bolt, Python M3TM, that is protected with an innovative PyFlexU2TM coating. The new generation Python M3 features improved steel chemistry for reliable performance, modified profile for better inflation, and surface preparation and coating application. The PyFlexU2 is impervious to liquid and air, durable, and UV resistant. With a flexible adhesive, and highly corrosion-resistant undercoating, and a very hard sacrificial surface coating, the PyFlexU2 coating system provides the Python M3 superior protection against chemical corrosion and physical scratch damage. The under-coating has exceptional flexibility and adhesion to prevent coating micro-cracks or fractures after bolt inflation and possesses excellent corrosion resistance to acids (pH <3), alkalis (pH >11), fuels, and salt solvents. The corrosion and scratch resistant PyFlexU2 coating offers very effective bolt protection for extra longevity in highly corrosive environments. The Python M3 coated with PyFlexU2 has been tested in the most challenging conditions, including laboratory corrosion tests in extreme acidic and basic solvents, rock slurry, and borehole scratch insertion tests. With demonstrated corrosion and scratch resistance, the product has been greatly welcomed by hard rock mines in the West and is currently installed in large scale. This paper identifies the root causes of the bolt corrosion, discusses the analysis process, and details laboratory and underground tests carried out on the Python M3 coated with PyFlexU2. The Python M3TM and PyFlexU2TM are subjects covered by pending U.S. Patent Applications assigned to FCI Holdings Delaware, LLC."

Jan 1, 2017

By Eric Keller, Jamal Rostami, Wenpeng Liu

"Roof and rib instability is an important issue in underground mining. To optimize ground support design, enhance ground stability, and reduce the possibility of roof or rib failure with minimal use of artificial ground support, it is essential to have an accurate understanding of ground conditions. This includes the location of voids, cracks, and discontinuities, as well as information about the different strata in the immediate roof. This paper briefly introduces ongoing research on void detection by using the roof bolter feed and rotation pressure. The goal of this project is to improve the sensitivity of detection programs to locate smaller joints and reduce the number of false alarms. This paper has presented a brief review of the testing procedures, data analysis, logic, and algorithms used for void detection. In addition, this paper has discussed the results of preliminary laboratory tests and statistical analysis of the data from these two drilling parameters used for void detection.INTRODUCTIONRoof falls are one of the most serious and frequent accidents in underground mining. Each year, personnel are injured or killed because of roof falls. Equipment can also be damaged when this occurs. According to Mine Safety and Health Administration statistics collected from 1999 to 2008, ground falls were the largest cause of fatal accidents in underground coal mining, causing around 40% of all fatalities (NIOSH, 2015a). Out of 8 to 10 fatalities and over 800 injuries are recorded each year in underground mines, there are nearly 2,000 reportable non-injury ground falls every year (NIOSH, 2015b).Certain features in the ground, such as voids, cracks, and discontinuities, are significant factors that cause roof support failures and roof fall accidents. Currently, several manufacturers provide smart roof bolters with limited capabilities for void detection. While successful in many instances, in laboratory experiments, the existing void detection systems have limited success in detecting void openings that are less than 1/8 inch This limited success was observed in testing concrete blocks with gaps in between, simulating a rock medium with voids. Detection programs have missed some voids, while, in some cases, they have shown false detection. These algorithms need to be more accurate in sensing voids to improve the capabilities of these programs."

Jan 1, 2016

By C. Dinis da Cama

In order to reduce the complexity of mechanisms influencing rock- fragmentation by blasting a simulation approach is proposed, using the capabilities of micro-computer interactive graphics. Situations involving cratering and bench blasting are simulated, and both jointed and intact rocks can be subjected to explosive action, taking into consideration its breakage mechanisms. Size analysis curves relating rock distribution before and after the blasts are determined and compared with field data.

Jan 1, 1984

By David L. Kuck

This paper describes a system for providing structural, support in underground mines, employing water ice for pillars. packwalls and brattices. It consists of a refrigeration brine chiller, brine circulation system, and disposable plastic containers. The system provides for the timely freezing of uniform ice pillars, and for ice maintainance and/or melting on demand. Unique, useful ice properties include: expansion upon freezing, resilience to dynamic loads, and plasticity. Ice will not dilute or contaminate coal or ore. Economic advantages include: 1) lower labor and material costs (water can be piped to the ice pillar site through mine-water, spray-water, or drill-water lines); 2) replacement or supplementation of timber. concrete or other roof support equipment; and 3) potential use of ice brattices as ventillation control; and 4) conversion of ice bratices to ice pillars upon retreat. See Figure . A safety advantage for personnel and equipment is that ice pillars can be placed in hazardous sites, by remote control, if neccessary, without human entry. All filling, freezing and melting operations can be controlled from a safe distance.

Jan 1, 1987

By A. W. Khair

This paper presents an analysis of fracture depth and intensity due to subsidence over the longwall panel. Sonic reflection techniques were utilized to determine fracture depth, and a variation of p-wave velocity was used as an indication of the fracture intensity. Instrumentation has been tested for consistency and accuracy first in the laboratory using small scale models, then applied in the field in two mine sites with different mining geometry and geologic conditions. A new sonic viewer was utilized for sonic velocity measurements. Regular hammering method was on acoustic source. The results were concurrent with monitored horizontal strain profiles and measured open fractures over the longwall panels.

Jan 1, 1989

By Peng Cao, Jimin Su, Yang Li

"Abutment pressure distribution is different when a longwall panel is passing through the abandoned gateroads in a damaged coal seam. According to the geological conditon of panel E13103 in Cuijiazhai Coal Mine in China theoretical analysis and finite element numerical simulation were used to determine the front pressure distribution characteristics when the longwall face is 70 m, 50 m, 30 m, 20 m, 10 m, and 5 m from the abandoned gateroads. The research results show that the influence range of abutment pressure is 40 m to 45 m outby the face, and the peak value of front abutment pressure is related to the distance between the face and abandoned gateroads. When the distance between the longwall face and abandoned gateroads is reduced from 50 m to 10 m, the front abutment pressure peak value kept increasing.When the distance is 10 m, it has reached the maximum. The peak value is located in 5 to 6 m outby the faceline. When the distance between the longwall face and abandoned gateroads is reduced from10 m to 5 m, the front abutment pressure sharply decreases, the intact coal yields and is even in plastic state. The peak value transfers to the other side of the abandoned gateroads. The research results provide a theoretical basis for determining the advance support distance of two gateroads in the panel and the reinforcement for face stability when the longwall face is passing through the abandoned gateroads.INTRODUCTIONFront abutment pressure is the result of rearrangement of in situ rock stress caused by the mining (removal) of the coal seam. Research on the distribution character of face abutment pressure have significant importance in confirming the width of the coal pillar and the distance of advance support in roadways (Liu et al., 2011; Liu, Jiang, and Zhu, 2015). Currently, there is a lot of research on abutment pressure characteristics of traditional longwall coal faces, thick coal seam longwall faces, isolated faces, and extra wide face abutment pressure distribution (Xie et al., 2006). However, theoretical analysis and research on the distribution law of the fully mechanized coal face to abandoned gateroads are relatively less. Abandoned roadways are often from less mechanized or room and pillar mines. Due to the existence of these roadways pre-longwall mining, the in situ stress has already been redistributed around the roadway (Liu et al., 2007). Thus, when the longwall approaches and mines through the roadway, the abutment pressure distribution behaviour has different characteristics than those of traditional solid undisturbed coal. Especially when the face approaches the abandoned roadway, the understanding of face abutment pressure distribution has significant importance to the timing of support installation (Ren and Ning, 2014). This prevents the occurrence of a roof and rib failure ahead of and on the longwall and highly efficient advance of the longwall safely and productivity. This paper analyses the E13103 face of the Cuijiazhai Mine of Wenzhou Mining Co., Ltd of Kailuan Group, as the engineering case study, and uses FLAC3D numerical simulation software to conduct numerical simulated analysis on the abutment pressure distribution mechanism of longwall coal mining face."

Jan 1, 2018

By Wm. Mark Hart

Under a specific geological condition, roof supporting method, and pillar-entry system, an entry convergence concept may be the most effective means that can be used to effectively indicate the longwall entry stability (i.e. pillar bumps, roof falls, or floor beaver This concept may also be used to verify the effectiveness of the current pillar-entry system and roof supporting method. Furthermore, convergence measured under different mining phases may lead to a better understanding of the longwall mining-induced abutment loads and may be used to estimate stress change in pillars and thus pillar stability. In this paper, a remote entry activity monitoring system was designed; a comprehensive entry convergence monitoring strategy was proposed; thee abutment loading phases in longwall mining were defined; the relationship between roof deflection and stress change in a pillar was derived, and finally the extent and magnitude of the mining-induced abutment loads as well as their impact on entry convergence were discussed using the field data obtained so far.

Jan 1, 1995

By Meagan S. Boltz

From October 2000 to April 2001 a local array of fourteen seismograph stations was deployed at the Trail Mountain Mine (TMM), an underground coal mine in Emery County, Utah, to locate mining-induced seismicity (MIS). Original analysis of the data provided epicentral locations that coincided closely with the active longwall panel. The original analysis yielded poor quality hypocenters, however, preventing a useful relation from being made between mining activity and the event depths. For the original analysis, only stations at elevations above mine level were used for locating MIS. As a result, P- and S-arrival times from four of the stations in the local array were not used: an inmine station and three stations at elevations below mine level. This study compares mine workings and active mining to a revised TMM dataset that included P- and S-arrival times from the lower elevation stations that were not used in the previous study. In the revised locations, a modified master event methodology was used to calculate station delays. These station delays correct for errors in the shallow layers of the velocity model. The resulting hypocentral locations have improved depth resolution, determined by a lower root mean square (RMS) for the locations, compared to the original study. Most of the events occur in the roof of the mine and follow the longwall panel. When located using the velocity model determined in the original study, the elevations of the events increase as the longwall panel progresses. One possible explanation for the elevation increase is that it may be related to geology or the caving process. As presented here, a 10% decrease in the shallow velocity structure results in a more plausible location for the hypocenters. Consequently, it is hypothesized that progressive development of the TMM longwall panel(s) may have resulted in a progressive change in the velocity model.

Jan 1, 2012

By D. A. Payne

Large excavations, such as Iongwall panels, result in extensive vertical stress redistribution in the surrounding strata. The large abutment stresses developed may produce damage to pre-existing or planned excavations in the same seam or in seams above and below the workings. Knowledge of the magnitude and location of these stresses is therefore important in the design of mine openings; pillar sizes for panel and pillar layouts, roof supports in longwall gateroads and workings over or above pre-existing or planned extraction in adjacent seams. In an attempt to reduce costs, the Cape Breton Development Corporation (CBDC), a Federal Crown Corporation responsible for operating two retreat longwall coal mines, examined the potential for either interpanel barrier pillar width reduction or entire pillar elimination by the adoption of dual life gateroads for the longwall panels. In order to assess the potential for reduced interpanel barrier widths or total elimination, an investigation of the redistribution of vertical stresses around longwall panels in the Sydney Coalfield was established. The study was conducted jointly by the Cape Breton Coal Research Laboratory (CBCRL), of CANMET (a division of Natural Resources Canada) and the Denver Research Center (DRC) of the United States Bureau of Mines. The program included monitoring of vertical stress changes around longwall panels and gateroad behaviour in two seams. USBM-style hydraulic borehole pressure cells connected to chart recorders for continuous monitoring were deployed at four sites, two at Lingan Colliery and two at Phalen Colliery. This report describes the investigations conducted at Phalen Colliery. Contoured plots of stress redistribution around two sites are presented.

Jan 1, 1995

By Ruixiang Gu

The de-confinement mechanisms of unstable failures as they occur in deep coal mining conditions are investigated using a distinct element numerical modeling code. The Mohr-Coulomb and continuously yielding joint constitutive models were used to study the compressive failures in coal and slip behavior of coal-rock interfaces, respectively. The effect of strength variations within interfaces on the failure mechanism of mining faces is also studied. The stability of interface slip failures was found to have a significant role in the failure mode of coal sidewalls. When the interfaces experience stable slip failures, the sidewalls are more likely to fail in a stable manner. With occurrence of unstable slips at interfaces, unstable compressive failures of sidewalls are triggered. The numerical modeling results support the proposed de-confinement mechanisms and emphasize the importance of including the coal-rock interface behavior in the analyses of unstable compressive failures. The significance of the proposed mechanisms in underground mining conditions is that rock discontinuities with large cohesion drop can become potential factors, inducing unstable compressive failures at ribs and mining faces. Therefore, the de-confinement mechanisms should be taken into consideration in mine design.

Jan 1, 2014

By Russell Frith

For many years, underground rock mechanics and in particular, roadway/tunnel roof stability has been underpinned by the often unchallenged assumption that roof strength (as defined by the UCS) and stiffness (E) are key stability controls. This has logically led to the proliferation of laboratory testing of rock specimens and the development of indirect geophysical methods to gain estimates of these two rock parameters. Furthermore, many design methods are significantly focussed on replicating rock mass behaviour through either intact or failed constitutive models. Demonstrably the strength and stiffness of the host rock material is commonly used as one of the key indicators of excavation roof stability and it finds either direct or indirect use in just about every rock mass rating system in use today. In more recent times there has been a common move to consider and apply (even if only conceptually at the current time) structural engineering type principles (e.g. buckling) to coal mine roadway roof (and rib) stability. Similarly our knowledge of the in situ stress environment and its likely origins has improved significantly, largely through stress measurements and subsequent analysis. This paper combines knowledge in both of these fundamental areas through a deterministic model for roadway roof stability and in combination with field examples, reaches the almost certainly controversial conclusion that UCS and E are commonly irrelevant, albeit that the former may provide an indication of other relevant geotechnical parameters (e.g. bedding cohesion). As with all hypotheses or rules, there are naturally exceptions and in this case, the most obvious is the tailgate of the longwall panel (with adjacent goaf). Due to the significant change in the strata loading environment of a longwall tailgate as compared to first workings for example, the stability equation materially changes so that UCS and E become critical controls. The point of the paper is to present a different perspective on a traditional mining problem and to challenge geotechnical professionals to keep thinking ?outside of the square? in the never-ending endeavour to improve our understanding of the engineering problems we regularly face. Such an understanding impacts upon such issues as geotechnical data collection from borecore, support hardware requirements and design capabilities. Therefore making the assumption that our understanding is always fundamentally correct could in fact be limiting the development of new and improved engineering in the future.

Jan 1, 2006

By Steve Tadolini

Underground roof falls can have devastating effects on the safety of operations personnel, and equipment, and seriously impact production. Immediate steps are usually taken to danger off and secure the area while clean-up efforts are designed and implemented. A critical step, often overlooked due to production demand, is the determination of - why the roof fall occurred so that additional occurrences can be avoided in future developments or what measures can be taken to identify areas that have similar ?symptoms?? Forensic engineering includes the investigation of materials, products, structures or components that fail or do not operate/function as intended. The authors define forensics in ground control engineering as the study of evidence discovered while examining underground roof falls by applying expert observational techniques and established mining engineering principles to determine the probable cause, hypothesize solutions, and design engineering safeguards to prevent reoccurrences. Simply stated, the primary steps in the forensics of underground roof fall techniques are: ? Assess regional and local conditions prior to the event. ? Assess post-event conditions. ? Hypothesize plausible ways in which the pre-event conditions ? became the post-event conditions.Search for evidence that either denies or supports the various ? hypotheses.Apply engineering skill to relate the various facts and evidence into a cohesive scenario of how the event may have occurred. This paper details the proposed technique by utilizing a roof fall case study that required the examination of five primary factors: mine design parameters, excavation geology, method of excavation, method of support, and mining cycle times.

Jan 1, 2009

By Peter Zhang

Shield recovery in a longwall move is normally conducted from tailgate to headgate. However, if the face is wide and the immediate roof is weak, difficult conditions with considerable roof sag, excessive shield load, and local roof falls could occur as the shield recovery proceeds to the middle of the face, causing delays in shield recovery. The situation could be aggravated when a pre-driven longwall recovery room is employed. Alternatively, a bi-directional approach for shield recovery, i.e. shield recovery starting from the middle of the face towards both tailgate and headgate, can alleviate the roof sag significantly by quickly withdrawing the shields towards the lower abutment pressure zones at the headgate and tailgate sides. In this case, the bi-directional shield recovery approach was used in a longwall move for a 1450 ft wide face under weak roof conditions. Shields were successfully withdrawn within five days without experiencing significant roof sag. The time-dependent roof-to-floor convergence, shield pressure, and roof conditions were monitored during shield recovery. 3-D finite element modeling was conducted prior to longwall move to evaluate the difference between a uni-directional and a bi-directional shield recovery during a longwall face move. Vertical stress, yield zone in and around the recovery room, load on the shields, and convergence at the center of the shield canopy were obtained from computer modeling, and compared with the data from field monitoring. Finally, the advantages of the bi-directional shield recovery are discussed.

Jan 1, 2007

By John Stankus

Accurate evaluation of stress and geological conditions is critical to ground control design in underground openings. For a mine slope entry, the problem becomes more complicated because a slope transverses through many different types of strata. Mine slope ground control has traditionally been practiced based on trial and error and prior experience. There is currently no well-accepted slope and support design methodology available for an economical and technically sound ground control plan. Over the last few years, Keystone Mining Services, LLC (KMS), the engineering affiliate company of Jennmar Cooperation, has developed a ground support design methodology called the ?Stress, Geologic, and Support design system? (SGSSM). This patent pending method enables accurate analysis of actual geo-technical conditions and stress; identifies strong, fair, and weak sections along the slope; formulates primary and supplemental roof bolting systems, designs optimal long-term steel structure support; and verifies the adequacy of the developed support. The method has been successfully utilized on various new slope projects and has been well received by state and federal regulatory agencies during the approval process. This paper details the concepts of the methodology using an actual case study of a slope project in the Midwest.

Jan 1, 2011

By Shosei Serata

Serious floor heave of up to 2.4 m in a 2.4-m high mine entry was eliminated by applying the stress control method of mining, as a last resort, at the No. 5 coal mine of Jim Walter Resources, Inc., in the Black Warrior coal basin near Birmingham. Alabama. Underground observation of the first 3-room entry created using the stress control method is discussed here. The behavior of the test entry, which eliminated the heave problem, is analyzed in relation to similar studies conducted in a salt mine under similar ground conditions by utilizing finite element analysis.

Jan 1, 1984

By Kot Unrug

Mine seals are necessary in nearly every mine to isolate mined-out areas from the ventilation network. There is a large number of seals in active mines and that number continually increases as the development spreads across the reserves. The recent accident caused by the failure of seals in the Sago mine resulted in new regulations. These regulations have been set based on a principle of eliminating the risk of failure, rather than the sound engineering and understanding of the conditions that may cause seal failure during an explosion of methane in sealed areas of the mine including the probability of such occurrences. This paper discusses the following subjects related to mine seals: The potential causes of methane explosions and the dynamic effects of pressure wave propagation. Seal materials and methods of construction in view of the interaction of the seal with the host rock environment as well as requirements for gathering geotechnical data. The design of seal dimensions is based on loading conditions, therefore the probable ranges of such loading is reviewed. There is also discussion of possible methods for shielding of seals from pressure pulses following an explosion. Particular seal?s types are examined in reference to the conditions at the seals location. A novel design is presented that will be a low- cost solution for the sealing of mined out areas. Recommendations are given for further research leading to a rational engineering system for design of new seals in coal mines.

Jan 1, 2008

The purpose and current practice of cable trusses in underground coal mines is briefly outlined and details of various cable truss designs are presented. The main part of the paper describes the in-situ performance of cable trusses installed as secondary supports in gateroads and recovery roads of longwall coalfaces. The performance analysis is based on the results of in-situ monitoring carried out at a number of sites at two underground coal mines within Australia. Truss performance has been assessed as load developed in relation to roof convergence, face position and time. Additionally, the influence of strata conditions, installation pattern/density, roadway layout and geometry have been taken into account. An analytical model has been developed to predict truss loads. The principal variables are listed and the basis of the model is described. Based upon behaviour observed in the field the model has been progressively upgraded and validated against measured performance. Guidelines on truss performance and factors which influence it are presented and the implications of these to the use of cable trusses is discussed. Possible methods for improving truss performance in certain strata conditions are outlined and some comments are made on the value of cable trussing compared to cable bolting in these situations,

Jan 1, 1992

By Ghassan Skybey

Australian coal mines uses state of the art technology in coal rib reinforcement. This paper highlights the development over the past 15 years in coal rib support technology, along with the advantages and disadvantages of each system. It also outlines the current trend in using coal rib reinforcement in speeding up the dowels installation to improve the current low drivage rate. An innovative cuttable dowel is discussed which improves the drivage rate. This new dowel is self anchoring it uses no resin anchor it has a 5 tonnes (5.51 tons) anchor capacity and can be fully installed in approximately 10 seconds.

Jan 1, 1995

By Kevin Beauchamp

In many cases traditional support designs cover the many variations in ground conditions and bolt performance by a conservative factor of safety. The result is that most bolts are ineffectual most of the time and yet the response to occasional roof collapses is an even more conservative design. The probabilistic analysis presented in this paper takes several important parameters of a support design into account such as span, bolt strength, bolt length, water pressure, seismic accelerations, joint orientation, bed thickness and joint strength and allows the effect of variations in these parameters to be evaluated simultaneously. The analysis demonstrates the application of the probabilistic approach to both blocky, wedge-dominated conditions and bedded deposits dominated by laminations. All mine excavations have a designed stand-up time. By taking into account of the possible variations in the design parameters explicitly, it is possible to produce a support system designed to ensure stability over a given period of time. Rather than use a factor of safety criterion, the approach uses a percentage reliability or probability of failure. By understanding the probability of failure of the support system, it is possible to improve the performance of ground support without any increase in cost or conversely to decrease the cost while maintaining the performance of ground support. This approach reduces reliance on empirical experience and leads to a better understanding of the key factors that influence stability and can provide a much more accurate and optimized assessment of support design and performance. The result is a more cost-effective support system and we hope that a broader application of this approach to ground support in underground mines will lead to a greater acceptance in the industry of probabilistic analyses and of terms such as Probability of Failure and Reliability of Support.

Jan 1, 2003