Search Documents

By Wenbing Xie

At Renlou Coal Mine, Huaibei Mine Area, the track entry deformed significantly after longwall mining in an overlying multiple seams. The supporting characteristics of primary roof bolts and shotcrete with wire mesh are closely related to the movement of the mine?s surrounding strata. A case study of a track entry deformation was monitored during the longwall mining of a selected overlying panel. The measured data showed the unique entry deformation pattern during the longwall mining in the overlying seam. Underground extensometer measurement showed that entry stability was mainly affected by the periodic roof weighting of longwall mining in the overlying seam. The displacement of the deeper strata occurred a head of the immediate vicinity of the entry. Thereafter, deformation of the roof and floor strata was in the form of shearing of the shallower strata. Due to the use of heavy-duty roof bolting with wire-mesh, the roof-tofloor and rib-to-rib convergences were small, but the floor heave was large, greater than 80% of the roof-to-floor convergence. The measured displacement from extensometers varied with the position of the monitored cross-sections and depth into the roof. There were several deformation patterns, such as shearing movement, compression, and expansion, and the variations between compression and expansion. Strata compression at the entry surface was always accompanied with shearing movement at the deeper strata. During the longwall mining, the whole surrounding strata of the entry moved toward the opening. Underground practical experience indicated that prior to mining, the entry was supported very well in excellent conditions. After mining, however, it deformed greatly. The current entry support technology was not effectively control the severe deformation incurred in entries driven in soft strata due to the following reasons: (1) little is known about the entry deformation behavior of the strata surrounding the opening and (2) the degree of interactions between entry deformation and roof bolting with wire mesh is not well understood. Consequently, effective supporting systems cannot be properly selected to control its deformation and maintain a stable supported surrounding structure.

Jan 1, 2012

The purpose and current practice of cable trusses in underground coal mines is briefly outlined and details of various cable truss designs are presented. The main part of the paper describes the in-situ performance of cable trusses installed as secondary supports in gateroads and recovery roads of longwall coalfaces. The performance analysis is based on the results of in-situ monitoring carried out at a number of sites at two underground coal mines within Australia. Truss performance has been assessed as load developed in relation to roof convergence, face position and time. Additionally, the influence of strata conditions, installation pattern/density, roadway layout and geometry have been taken into account. An analytical model has been developed to predict truss loads. The principal variables are listed and the basis of the model is described. Based upon behaviour observed in the field the model has been progressively upgraded and validated against measured performance. Guidelines on truss performance and factors which influence it are presented and the implications of these to the use of cable trusses is discussed. Possible methods for improving truss performance in certain strata conditions are outlined and some comments are made on the value of cable trussing compared to cable bolting in these situations,

Jan 1, 1992

By Tom Blevins, Roland Walker, Jinsheng Chen

"The Dywidag-Systems International DSI Tandem Anchor bolt, with an improved expansion shell-washer design, can substantially reduce potential entry roof falls caused by twisted or deformed expansion shells of the traditional mechanical anchor bolts during installation. In addition, the improved anchorage system can also ensure that a consistent and high installed load is achieved, which is critical for effective beam building under thinly laminated or layered roof conditions. This paper discusses the genesis and anchorage performance of the Tandem Anchor bolt, and analyzes the tension/torque relationship of different mechanical shell anchors using data obtained from both lab and field tests. It also discusses roof bolting mechanisms, roof bolting systems, and factors influencing effective beam building. Finally, numerical modeling was used to analyze the effect of bolt pretension magnitude on entry roof stability.INTRODUCTIONThroughout the history of underground mining, keeping the roof from uncontrollable collapse has been the greatest concern of the miner. Tremendous strides have been made in better understanding, predicting, and supporting the mine roof. This conference has spent the last twenty-eight years sharing information and distributing it to the mining community. A paraphrased statement from former Secretary of Defense Donald Rumsfeld adequately describes the challenges to the mining engineer as it pertains to roof control: it is a study of known knowns, known unknowns, and unknown unknowns. It is the hope of the authors to address some of these unknowns.The paper discusses the development of bolt anchorage systems from dry shells to shells with resin-assisted anchorage. It looks at some of the issues faced with the anchorage shells being used when introducing the insertion pressures caused by resin cartridges. The rationale behind the shell design changes was to compensate for this resin induced stresses.An improved expansion shell assembly (a slotted expansion shell base, a tapered cramming plug, and a novel support nut with tapered top) for mine roof bolts makes up the Tandem Anchor (U.S. Pat. No. 6742966); this minimizes the possibility of twisting seen with traditional mechanical shells and thus prevents springy bolts and shell leaves from breaking. A fully grouted Tandem Anchor bolting system has the advantages of both the pure mechanical point-anchor and the non-pretention fully grouted bolting systems. Once installed, the installed load or pretension will be locked in and never bleed off. Compared with the fully-grouted (2-speed resin) tension rebar bolting system, the fully-grouted Tandem Anchor bolting system can (a) reduce bolting cycle time (about 15 seconds per bolt), boosting coal production and productivity; (b) provide a greater installed load or pretention; and (c) achieve a consistent tension/torque ratio, which gives better bolting quality control. Therefore, a fully grouted Tandem Anchor bolting system is the most effective means to reinforce a weak rock mass intrinsically by the theory of beam building. For thinly laminated or layered roof conditions, a higher installed load or pretention (50% or more of the bolt's yield strength) can make a roof bolting system much stiffer, which results in less roof movement. Numerical modeling results show that the magnitude of the roof's tensile stress and relaxation zone can be substantially reduced under a higher installed load or pretention."

Jan 1, 2010

By Yuanwci Shi

This paper discusses the results of research on the interaction between roof strata and shield supports including the active and passive supporting functions of the shield supports which prevents roof strata separation; pressure distribution on the canopy and under the base plate as measured in the laboratory and underground; comparison between various shield structures regarding their effectiveness on roof and floor control; and determination of optimum support capacity under given geological and mining conditions including hard-tocave roof

Jan 1, 1997

By Dan Payne

The Crinum mine has recently completed workings in the southern area of the mine. Over the 10 years of longwall production 40 million tonnes have been extracted and the mine has experienced over 40 longwall face, 3 main gateend, and 2 tail gateend roof falls as well as 5 roadway roof falls away from the longwall. Weak roof (less than 10MPa (1450psi) in the bolted horizon) has been the principal roof control issue at the mine. However, weak, highly cleated coal, water inflow from overlying aquifers, some minor structure and a diatreme in the main headings have also contributed to the challenges at the mine. This paper describes the geotechnical experience over the 10 years, the mine?s approach to addressing the issues and the relative success of these approaches.

Jan 1, 2008

By Deren Zhu

Based on the results of in-situ observations and physical model analysis, a computer simulation method, FEAEBP, has been developed to predict the behaviors of main roof breakage in longwall mining by considering it as a Kirchhoff plate on Winkler elastic foundation. This method in used to investigate the initiation, and development of the breaking process of main roof and its displacement field before and after its breakage. In this paper the simulation method is introduced, characteristics of the displacement field of the main roof is discussed and monitoring variation of the displacement field of the main roof in a Chinese longwall face is demonstrated.

Jan 1, 1989

By Madan M. Singh

Currently longwall coal mining operations require at least 3 entries on both the headgate and tailgate ends because of ventilation and safety requirements. Driving of entries, however, is a slow and costly process. Often it is a bottleneck in longwall development. Single entry gateroads are permitted in Europe and commonly used there. This study entailed ascertaining the feasibility of using a single entry in the United States, without sacrificing safety. This design was conducted for an operating longwall mine in the Black Warrior coalfield in Alabama, An understanding of rock loads and consequent support requirements is prerequisite to the design and successful demonstration of the single entry system. Efforts in this regard were directed at determining center (packwall) support requirements for various single entry widths. Critical to the analysis is knowledge of the nature and extent of side abutment stresses. In collecting geological and geotechnical information relating to the stability of the single entry, Engineers International, Inc. engaged in the following: ? Examination and inspection of the single entry demonstration at the Sunnyside Mine in Utah. Severe ground conditions and unacceptable levels of entry closure were experienced there prior to the tailgate phase. Observations at the mine presented a clear perspective on possible ground control problems for future single entry designs. ? Reconnaissance inspection and classification of roof rock conditions. ? Detailed mapping of roof structure in the areas to be instrumented. ? Installation of convergence stations in the longwall headgate to monitor roof movement during mining. ? Measurement of side abutment stresses in a yield pillar in the area of the convergence measurements. ? Measurements of coal fracture distribution by the detail area method. ? Rock properties determinations of roof, coal, and floor rocks; samples obtained by core drilling. ? Determination of floor bearing capacity by in-situ testing.

Jan 1, 1982

By Meagan S. Boltz

From October 2000 to April 2001 a local array of fourteen seismograph stations was deployed at the Trail Mountain Mine (TMM), an underground coal mine in Emery County, Utah, to locate mining-induced seismicity (MIS). Original analysis of the data provided epicentral locations that coincided closely with the active longwall panel. The original analysis yielded poor quality hypocenters, however, preventing a useful relation from being made between mining activity and the event depths. For the original analysis, only stations at elevations above mine level were used for locating MIS. As a result, P- and S-arrival times from four of the stations in the local array were not used: an inmine station and three stations at elevations below mine level. This study compares mine workings and active mining to a revised TMM dataset that included P- and S-arrival times from the lower elevation stations that were not used in the previous study. In the revised locations, a modified master event methodology was used to calculate station delays. These station delays correct for errors in the shallow layers of the velocity model. The resulting hypocentral locations have improved depth resolution, determined by a lower root mean square (RMS) for the locations, compared to the original study. Most of the events occur in the roof of the mine and follow the longwall panel. When located using the velocity model determined in the original study, the elevations of the events increase as the longwall panel progresses. One possible explanation for the elevation increase is that it may be related to geology or the caving process. As presented here, a 10% decrease in the shallow velocity structure results in a more plausible location for the hypocenters. Consequently, it is hypothesized that progressive development of the TMM longwall panel(s) may have resulted in a progressive change in the velocity model.

Jan 1, 2012

By Nengxiong Xu

The WTZ coal mine is located adjacent to an auxiliary dam in P. R. China. The mining-induced ground movements are calculated using a 3-D numerical procedure based on the finite difference method (FDM) to judge whether the extraction of the coal seam will have a negative impact on the dam. First, the values of the rock mass mechanical parameters in the numerical model are estimated using the available literature that relates intact rock and discontinuity properties to rock mass parameters. Then, based on available surface subsidence monitoring data for an area in WTZ mine, the main mechanical parameters of coal and rock masses are calibrated by a back analysis procedure that combines an experimental design technique with numerical simulations. Then the reliability of these rock mass parameters is verified. Finally, according to the planned mining sequence, predictions of mining induced surface subsidence are computed in steps, and the boundary of the ground movement area of each step is determined. The nearest distance from the boundary of the surface movement area to the edge of the dam foundation was found to be about 1347 m. The maximum surface subsidence within the mining area turned out to be 2.7 m, and the maximum settlement point was found to be close to west-south corner of A2 mined area. These findings led to the conclusion that the coal seam mining would not cause dam damage.

Jan 1, 2013

By Shosei Serata

The application of conventional rock mechanics methods to complex ground is very difficult. Yet. In most underground mining, the ground is complex. Therefore. conventional methods are not only difficult to apply but are also generally ineffective in improving underground operations. Similarly, conventional rock mechanics instrumentation has not significantly contributed to improvement of mining practice. Rock mechanics instrumentation in underground mining operations is often considered to be" merely an expensive nuisance. A new system of mine instrumentation is changing this traditional view. The new instrumentation method, called the SPDR method, was originally devised by Dr. Shosei Serata to meet the specific requirement of establishing the Stress Control Method of mining upon a solid quantitative foundation. This instrumentation method has contributed substantially to the widespread success of Stress Control mining under widely varying ground conditions in different types of underground mines (1.2.3.4). The instrumentation method provides an effective means for optimizing Stress Control mining patterns, simultaneously achieving reduction in production costs and substantial improvements in safety (5). The principles and methods of the new instrumentation method are described below, with field examples.

Jan 1, 1986

By Amirhossein Molavi Tabrizi

In this paper we introduce a realistic model for mine openings that explicitly considers the effects of local irregular topography. Also, we consider the effect of entry orientation and rock anisotropy on the induced stress fields around mine openings under the given in-situ stress field. A triangular mesh formulation is derived for representing complicated irregular surface topography and underground openings. Each element contains three internal collocation nodes. Parts of the surface which are far from the mine openings are discretized by infinite elements. The rectangular infinite elements with three internal nodes are introduced specifically for this problem so they are compatible with the triangular elements. With the corresponding boundary element method (BEM) formulation, we then investigate the combined effect of the topography and entry orientation on the stress fields induced by openings in anisotropic rocks under in-situ stresses. A single rectangular opening in the anisotropic ground with topography and in-situ stresses is simulated using data from the Carroll Hollow mine in Ohio. The results of these simulations show that topography, rock anisotropy, orientation of the regional stress field and mine opening geometry all have appreciable effects on the stress fields around underground openings, yet these factors can all be accounted for in an efficient code with no need to discretize the model domain. Future applications using this new BEM formulation will provide useful guidance on selecting the optimal opening orientation in the mine in order to minimize undesirable stress concentrations around underground mine workings.

Jan 1, 2014

By Antoni Kidybinski

Coal mining both with longwall and room-and-pillar method often encounters severe operational difficulties due to had roof conditions. Rooffalls at entry cross-cuts or along the rib line in longwalls as welt as dynamic and excessive loads on supports due to overhanging of strong roof layers in a goab - are well known phenomena to the mine operators. Also, a number of practical examples may be quoted of dramatic improvement of working conditions after changing of coal winning technology or supports type. It is therefore a question to be answered how far we are able to recognize roof strata properties before mining starts and adjust both coal extraction technology and supports of entries to rock stability foreseen. Furthermore, engineering principles and criteria for decision making should be established. In recent years several in situ rock strength and discontinuities detection testing techniques have been developed both indirect (geophysical) and direct thus making possible closer roof-strata examination. In this paper critical roof span criterion is discussed as a basis for selection of proper mining system in terms of desirable stability of mine opening .

Jan 1, 1982

By Anthony T. Iannacchione

This study, funded by the Appalachian Research Initiative for Environmental Science (ARIES), examines how mine layout, mining method, and geology interacted to allow water from the Grove No.1 mine pool to discharge into local surface waters. Federal and State regulations prohibit the discharge of acid or iron-producing waters from underground coal mines. Mining companies design barriers around their operations to prevent mine waters from discharging to the surface. The Grove No.1 represents one mine where these designs proved inadequate. Unique geologic conditions at the Grove No.1 mine pool, combined with retreat room-and-pillar mining, contributed to a discharge that required passive water treatment.

Jan 1, 2013

By William Bookshar

The development of increasingly more sophisticated and powerful retreat longwall equipment has led to ever wider and longer panels. To maximize gateroad development efficiency, provide for effective face recovery, andlor reduce ventilation pressures, entries are cut across longwall panels in advance of longwall retreat mining. These entries must be supported to prevent falls of immediate roof in advance of the face. Recently, cut through entries and predriven recovery room entries have been supported with various combinations of roof bolts and passive support. The cost and relative success of these support systems has varied considerably. Eighty-Four Mining Company, Fosroc, and Sub-Technical have developed and implemented an efficient, yielding, multiple component, cement crib to support longwall panel cut through entries and pre-driven recovery rooms. The cutable crib consists of an inexpensive flyash cement pillar poured in a bag, within a temporary metal form. The form is moved to a subsequent cutable crib location after the initial hardening of the flyash pillar. The remaining entry height between the mine roof and the top of the flyash cement pillar is filled with a specially designed bag filled with Fosroc's Tekset cement formulation. The diameter of the pillar and thickness of the Tekset bag are designed to accommodate the anticipated front abutment loading and entry convergence.

Jan 1, 1998

By Duk-Won Park

A vast majority of the operating longwall sections use shield-type face supports to provide ground control in the United States. As a co-operative research program between the University of Alabama (UA) and Jim Walter Resources, Inc.(JWR), a joint research program is underway to study interaction of shields with surrounding rock masses. A series of analyses on the response of shields are performed using monitored data at a longwall face in a deep coal mine. In this paper, various effects of parameters, such as leg pressure, setting load, developing load, maximum loading rate, pressure in capsule, and convergence between canopy and base, are discussed and recommended as stability indices. A microcomputer program is being developed for instantaneous interpretation of the shield monitored data, and for giving warnings of potential problems. The preliminary results define the effects of the setting load, developing load, and rate of developing load or leg closure rate. The objective of the study is to understand the shield characteristics and their interaction with surrounding strata in real time, then develop a reliable program for maintaining longwall stability.

Jan 1, 1992

By V. M. Shick

With gentle bedding within the zone of support pressure the delamination in roof rocks may occur only on those stratification planes where cohesiveness of rock is close to zero. Unlike this, at dip angles of more than 30-35° disintegration of rock occurs on the surfaces with cohesion up to 5 MPa. Therefore, the delamination in roof rocks at inclined beds is greater than at gently dipping ones. The original disintegration along the pressure fissures with the formation of block structure at inclined strata is not typical, and it may be observed only in roofs with included thick rocks; in this case, the orientation of fractures depends on the angle of seam inclination. Deformation of roof roocks above the mined-out space is determined by anisotropy of layers stiffness (hardness). With the increase of dip angle the own bearing capacity of layers will rise in the direction of strike. It was emphasized that the natural and technological factors are of great importance for rock pressure manifestation in longwalls.

Jan 1, 1996

By Vincent A. Scovazzo

Many accepted and useful methods have been developed and used for pillar design. Each method has its own particular strengths and weaknesses. Three methods addressed in this paper are; empirical, analytical, and numerical. Each of these methods have their place in pillar design. Analytical methods result in close approximation of the ideal pillar (most economical, stable, or yielding) and are suitable for use in final mine design and in analyzing existing problems. BOYD uses the analytical method to develop site specific mine pillars design equations. An analytical method, one of many developed by BOYD, is presented here and is based on the procedure used by Wilson (1) and others in development of their empirical equations.

Jan 1, 1995

By Gennaro Marino

Documented case histories are studied where data were found on the initial collapse of the overburden above the longwall panels. Under this scenario, the most controlled conditions exist for assessing the span capacity of the overburden (i.e., before failure the roof spans to fin coal abutments on two to all four sides). In an attempt to correlate theory to field observations, data are used on the overburden lithology, and the depth, width, and face advance of the panel, as well as, the subsidence conditions noted on the surface. The subsidence measured on the surface is used to determine when complete failure in the over- burden rock has occurred.

Jan 1, 1987

By G. R. Corbett

The introduction of roof bolts to Phalen Colliery in the Sydney Coalfield, Nova Scotia (annual output of 2Mt) has been successfully implemented in maingate and tailgate entries over the last four years. Monitoring of the roof bolted areas continues to be an integral part of the quality control program as the results are utilized to maintain safety and to aid in long-term design strategies. Although all gateroads in the Phalen Colliery have converted to roof bolts as their primary means of support, the majority of intersections which intersect the main slopes remain supported by large steel structures. Several intersections within the Phalen Colliery were monitored as they were created by the mining process. A comparison is made between intersections supported with only traditional 6.4 to 6.7 m steel structure and intersections supported by 2.44 m fully resin encapsulated roof bolts in conjunction with 7.6 m fully cement grouted cable bolts. Detailed monitoring was conducted using CA NM ET's intrinsically safe sonic probe extensometer datalogger which has the ability to read up to sixteen probes simultaneously at programmed intervals. The density of the data from the datalogger has allowed a better understanding of the deformation of cable bolted intersections than was possible with manual monitoring. Test results have helped mine operators to design safer cable bolted intersections.

Jan 1, 1995

By Victor Nazimko

A new technique for reaming the holes has been tested. This technique is available for reaming a hole at its deep end creating an enlarged cavity that has helicoidal grooves oriented at less than 40 degrees to the hole axis. This technique increases bolt resistance by a factor 1.3-1.62; its bearing capacity by 3 times and enhances underground roadway stability. This technique is suitable for great depth (1000m and greater) and weak wet rocks.

Jan 1, 2008