Search Documents

By Erdal Unal

In order to define the support parameters, by use of empirical approaches, it is particularly important to analyze the rock-load height that should be controlled by supports. The controlling mechanism however, depends on the type of support used there- fore, the rock loads should be treated differently. In this paper, an empirical equation is introduced which relates the rock-load height (ht) to a quantitative rock quality index (REIR), and roof span (B) as fallows:

Jan 1, 1986

By Shiva P. B. Kolli

Surface mining of multiple scams by mountaintop mining methodology is complex in the Appalachian region of West Virginia. Excess spoil from the removal of overburden and interburden is disposed in the adjacent valleys. The valley fills so formed are some of the largest earth constructions, with a relief of 450 ft (137 m) to 650 ft (198 m) and a stretch of 500 ft (152 m) to 2000 ft (610 m). The stability of the valley fills has become an issue of public concern. This paper describes three cases of valley fill slopes. The analysis of each case involved the description of the geo-mechanical properties of different surface and sub-surface layers, and the surface configuration of the slope. Slope stability was carried out using deterministic as well as probabilistic approaches. Based on the analysis, it was found that valley till slopes were stable due to configuration, and the premise that valley fills with great stretch and high volume of spoil tend to be unstable does not hold.

Jan 1, 2001

By Yong-Ming Jiang

In cooperation with Cyprus Twentymile Coal Co., researchers from the National Institute for Occupational Safety and Health (NIOSI-I), Spokane Research Laboratory, conducted a study at the Foidel Creek Mine, an underground coal mine near Oak Creek, CO, to evaluate the stability of underground working conditions as a longwall advanced through a series of backfilled cross-panel entries. Instruments installed in the cross-panel entry pillars, backfill, longwall panel, and adjacent headgate entry were continuously monitored by a computerized data acquisition system as the longwall approached and advanced through the backfilled section of the panel. Data collected from these instruments were analyzed to determine the magnitude and direction of the secondary principal stress changes ahead of the longwall face, deformation and closure of the headgate entry, and stability of the cross-panel entry pillars and backfill. A three-dimensional, boundary element model was calibrated to accurately predict mining-induced stress changes and the distance they occurred ahead of the longwall face. As the longwall advanced through the hackfillcd entries, most of the mining-induced load was supported by the cross-panel entry pillars. The backlill provided stability for the root and Moor of the in-panel entries and also confined the entry pillars significantly improving their load-carrying capacity. Comprehensive information derived from backfill material property tests, instrument data, underground observations, and numeric modeling results document the safety and stability of the 8-Right minethrough and should provide beneficial case study information fur other longwall backfilling applications in the future.

Jan 1, 1998

By A. Wahab Khair

This paper presents results of the experiments carried out in Beth Energy No. 33 Mine for the purpose of alleviating problems associated with cutter roof. Cutter roof problems have delayed the advance of the entry development considerably and maintenance cost of these entries was very high due to the requirement of very extensive and heavy artificial supports. The study includes assessment of the problem, investigation of the geology and lithology of the mines, study of in-situ stresses and corrective measures to combat the problem. Two approaches were selected as the corrective measures: 1) implementing yield pillar concept in order to reduce the effects of in-situ horizontal stresses, 2) designing an effective roof reinforcement system and application procedure. Results of this study revealed that roof strata is weak and in-situ stresses are very high at the problem area which results in development of cutter roof. Implementation of yield pillar concept was found to be ineffective because cutter roof often developed at the entry face concurrent to the development. However, proper design and implementation of roof reinforcement system stabilized the roof and eliminated roof caving during both entry development and retreat of longwall face, despite existence of the cutter roof, at a much lower cost.

Jan 1, 1992

By Song Yong Jin

The Jurassic coals at Datong are characterised by their strong, massive sandstone and conglomerate roofs which fail suddenly over large areas, crushing pillars and creating destructive windblasts, collapsed areas have exceeded 180,000m2 and windblasts have extended over one km underground and 200m on the surface and have been accompanied by subsidence troughs on the surface. Scientific analysis has researched premonitory signs of caving and the nature of windblasts leading to considerations of alternative mining methods and ways of dissipating the energy of windblasts to reduce their damage and danger.

Jan 1, 1992

By R. Karl Zipf

Multiple seam mining interactions caused by full extraction mining, whether due to undermining or overmining, frequently involve tensile failure of the affected mine roof. The adverse ground control conditions may prevent mining for both safety and economic reasons. Prior researchers have identified the geometric, geologic and mining factors controlling multiple seam mining interactions. This numerical study examines the mechanics of these interactions using a modeling procedure that 1) incorporates the essential constitutive behavior of the rock such as strain- softening of the intact rock and shear and tensile failure along bedding planes and 2) captures the geologic variability of the rock especially the layering of weak and strong rocks and weak bedding planes. Specifically, the numerical study considered the effect of vertical stress, interburden thickness, and the immediate roof quality of the affected seam in both undermining and overmining situations. The models show that for overburden-to-interburden thickness (OBAB) ratios of less than 5, interactions do not occur, and that for OBAB more than 50, extreme interaction is a certainty. In between, the possibility of an interaction was found to depend on gob width-to-interburden thickness ratio, site specific geology and horizontal stress to rock strength ratio in addition to the OBIIB ratio. The models also showed that horizontal stress was profoundly altered well above or below a full extraction area and that these changes are likely to influence the success or failure of multiple seam mining. The role of horizontal stress in multiple seam mining interactions has received little attention in prior investigations. Four factors control the mechanics of multiple seam mining interactions: 1. vertical stress concentration 2. horizontal stress concentration 3. stress re-direction 4. bedding plane slip bands A combination of vertical and horizontal stress increase and high stress gradients in the vicinity of full extraction areas re-orients principal stresses into a very unfavorable direction. This seemingly small stress re-orientation has a profound adverse effect on bedded rock.

Jan 1, 2005

By G. C. Xiao

A database, incorporating historical data from British mines, to study the factors affecting inflows from proximate aquifers into longwall workings, showed that a main casual factor was the immediate roof strata lithology. When this comprised principally stronger sandstone, there was a tendency for periodic inrushes associated with face weighting. This phenomenon is explained by the collection of water in bed sepa¬ration cavities, where free water connected to a high pressure head aquifer source, may be trapped.

Jan 1, 1990

By David H. Y. Tang

The reinforcement mechanism of suspension effect is analyzed based on beam-column theory. The equations of the maximum bending stress, deflection and transferred bolt load for the bolted roof strata are derived. In the analysis, the bolt load is assumed to be point load and the horizontal stress is uniformly applied to each stratum. The reinforcement mechanism of friction effect is also analyzed. The major function of roof bolting in this case is to create the friction¬al resistance by tensioning the roof bolts, thereby the individual thin strata are "welded" into one single thick stratum. Based on the results, equal spacing of roof bolts is used in the suspension effect while for friction effect, the bolts should be spaced based on equal shear force concept. The design nomographs for the proper bolting pattern and bolt ten¬sion of mechanical roof bolting systems are presented for practical applications.

Jan 1, 1984

By Michael Trevits

The NIOSH Lake Lynn Laboratory (LLL) is a unique research facility, located about 50 miles southeast of Pittsburgh, Pennsylvania, that is designed to provide a full-scale mining environment for testing and evaluation of mine health and safety technologies. The LLL occupies more than 400 acres and is composed of surface test and training areas and an underground mine. The Lake Lynn Experimental Mine (LLEM) was built at an abandoned commercial limestone quarry where surface mining ceased in the late 1960's. Later, new underground development was constructed to simulate modern-day coal mining scenarios; including room-and-pillar and longwall mining layouts. In January 1994, a sinkhole opened southeast of the No. 4 Portal of the LLEM and since then, the area of the underground failure and surface deformation has continued to expand and now includes several interconnected sinkholes. A concern developed that the overburden instability could expand and affect the structural integrity of the nearby highwall and the No. 4 Portal. It was unsafe to conduct a detailed underground survey of the mine in this area because the mine roof conditions near the No. 4 Portal had deteriorated significantly. It was decided to investigate the overburden conditions near the No. 4 Portal using ground penetrating radar (GPR). A GPR survey grid was located along an access road that passes over the top of the portal. To delineate the mine conditions near the portal, antennas whose frequency spectra produced pulses centered near 100- and 200-MHz were used. The results of the GPR survey suggests that the overburden rock units appear to be laterally consistent to a depth of about 15-ft. Below that point, the overburden appears to be significantly disturbed and it was hypothesized that this area contains a large roof fall. A follow-up ground truth survey of the mine roof conditions was conducted from the mouth of the portal. It is concluded that the observations and measurements made from the radar records appear to be correct as a large roof fall was observed and measured from the mine portal area.

Jan 1, 2005

By Wolfgang Schott

The propagation velocity of in-seam seismic (ISS ) waves depends on frequency which is also known as dispersion. This dispersion is not only determined by the thickness of the coal seam and its dirt hand content (i.e. thickness and position), but also by the rock type and its condition (soft or compact) above and below the coal. A coal panel completely surrounded by roadways was investigated using the in-seam seismic transmission survey technique. Along the roadways the immediate roof was either sandstone and shale- The seam thickness varied between 1.20 m (sandstone in the roof) and 1.40 m (shale in the roof) and a fault system (normal faults) crossed the panel with a total throw of about the seam thickness. Below this coal seam another coal scam with a thickness of about 80 cm exists. Its interval shown by exploratory drilling changes from about 60 cm to more than 6 m (scam splitting). Tomographic inversion was applied to the dispersion of the measured ISS waves and velocity distributions were calculated at frequencies found to he most sensitive to changes in the seam thickness and the distance to the coal seam below. By correlating the velocity distributions with known values along the roadways approximate distributions of the coal seam thickness and the seam splitting within the panel were produced. The mining of the coal panel had already been finished and comparison was made between the survey results and the actual situation as far as it was documented. Prediction by the seismic survey was partly in good agreement with the actual held conditions or showed at least the same trends.

Jan 1, 2003

By G. Herget

To improve quality control of roof conditions, a program was carried out at Elliot Lake uranium nines in Ontario, Canada to test a portable TV camera system. This camera has a 29 mm diameter probe and is capable of identifying crock locations, crack width and approximate dip direction. The extent of fractures to the roof was checked with the aid of a vacuum system by placing packers in various boreholes and checking for communication. The removal of some rock bolts indicated an increase in fracture extent.

Jan 1, 1982

By Gustavo Herrera Rico

As part of a general effort to increase safety, efficiency, and profitability of its mining operations, MICARE personnel with the support of NorWest Mine Services, Inc. determined that the key to improving development mining was the implementation of roof bolting as the means of primary roof support for both main entry and longwall gate road development. Until mid-1994, MICARE had relied exclusively upon primary roof support systems composed of heavy steel beams and wooden posts. Support systems were designed, implemented, and evaluated that were successful in controlling the mine roof under extreme geological conditions. This paper describes the geological challenges, support selection criteria, and presents the instrumentation and 'mine measurements made to assess the bolting performance during the development and retreat mining process of longwall mining.

Jan 1, 1997

The formation of tension cracks in slopes is well known. Analytical studies require the determination of a critical slip surface for any slope and, in doing so, it is necessary to consider an appropriate tension crack. A general yet simple approach is proposed for identifying the critical slope failure surfaces associated with critical tension cracks. The minimum factor of safety consequently reflects both safety against shear sliding and tensile failure. In general, the critical slope failure surface for a slope determined in this way differs from that which is obtained without optimizing the position and depth of the tension crack. In particular situations, the difference is significant.

Jan 1, 1989

By Shosei Serata

Serious floor heave of up to 2.4 m in a 2.4-m high mine entry was eliminated by applying the stress control method of mining, as a last resort, at the No. 5 coal mine of Jim Walter Resources, Inc., in the Black Warrior coal basin near Birmingham. Alabama. Underground observation of the first 3-room entry created using the stress control method is discussed here. The behavior of the test entry, which eliminated the heave problem, is analyzed in relation to similar studies conducted in a salt mine under similar ground conditions by utilizing finite element analysis.

Jan 1, 1984

By M. E. Duncan Fama

The aim of the paper was to model numerically some aspects of the extraction of coal pillars by split and fendering. A two-dimensional elasto-plastic plane strain model with strain softening and interface modelling was used. The model was able to simulate the improvement of conditions experienced in lifting from the fender, when the roof adjacent to the fender has caved. In contrast, when a stook was left, providing support to a span of uncaved roof, the model predicted the fender would suffer considerably more deformation and strain.

Jan 1, 1992

By Jamal Hematian

Understanding the behaviour of rocks in a high horizontal stress field, such as that in Australia, is critical when analysing the stability of underground structures. This paper addresses the significance of the post-failure behaviour of rocks on the stability of underground structures which are under the influence of a high horizontal stress field. The research work was conducted through a combination of numerical modelling, laboratory testing and field investigation. A number of 2-D FE model of roadways were constructed based on the data obtained from laboratory testing and field investigations. The models were then analysed using three different solution techniques; simple linear-elastic, non-linear elastic-plastic and elastic-plastic with consideration of post-failure behaviour (softening model). Results indicated that the post-failure behaviour of rocks significantly influence the stress and displacement patterns around the roadway. The stress and displacement patterns as well as the extent of the yield zone around the roadway predicted by the softening model were in good agreement with that from the field study. Based on the results of the study, an appropriate support system has been suggested to govern the stability of roadways.

Jan 1, 1994

By Stanley J. Michalek

Good planning is critical to operating a safe and efficient mining operation. As the shallow coal scams become depleted, attention turns toward deeper mineable seams or remnant coal reserves. It is becoming more common to place a mine in a scam that is below or adjacent to existing mine workings. Significant research has been conducted regarding the ground control issues of multiple scam mining. However, safety aspects of the operation may not be fully considered. Safety issues include working below or adjacent to a flooded mine and controlling gas Communication between the active mine and the nearby mine. This paper will discuss the safety issues a mine operator should consider when working under or adjacent to mines that may be flooded with water.

Jan 1, 2000

By Salah Badr

Longwall mine layouts with their entries, chain pillars, face support systems, advancing mining faces and compacting gobs represent a geomechanically complex mining operation. Geomechanical aspects are further complicated if mining occurs at depths exceeding 350 m, as stresses induced adjacent to the excavations exceed the unconfined strength of the coal and result in fracturing of the sidewalls of entries and chain pillars during development. Traditional methods of geomechanical analysis, whether empirical or numerical, are unable to represent such behavior satisfactorily. Achieving some meaningful results requires explicit representation of the three-dimensional boundary conditions and implementation of appropriate constitutive models for the rock mass. This paper describes a numerical modeling methodology for deep longwall mines operation using the FLAC3D finite difference de, which incorporates a strain softening constitutive law for modeling failure of coal. An important aspect of the modeling method includes accounting for stress relief provided to the pillars and entries due to the increasing load applied to the compacting gob.

Jan 1, 2003

Large-scale shear apparatus is designed to investigate the shear hehaviour of simulated soft rock joints under constant normal stifmess condition. Regular saw-teeth profiles having inclinations between 9.5" and 26.5" have been tested. The strength envelope based on these test results indicates that predictions made by Panon (1966) are accurate for the lower asperity angles. However, for higher asperity angles, Patton's model overestimates the shear strength especially in the low to medium normal stress range. In contrast, while Barton's model (1973) is realistic for Constant Normal Load (CNL) condition, it seems to be inappropriate for modelling the shear behaviour of soft joints under Constant Normal Stiffness (CNS) condition. An empirical strength envelope for the prediction of peak shear strength of joints is proposed in this study to account for the change in normal stress and surface degradation during CNS shearing.

Jan 1, 1997

By Ken Mills

This paper describes the first successful use of hydraulic fracturing to induce caving events "on demand" in Australia. Moonee Colliery operate a longwall immediately below a thick conglomerate strata. This strata temporarily bridges across the extracted longwall panel to create a large area of standing goal' When this standing goat' eventually collapses, the windblast generated presents a significant hazard to men working on and around the longwall face. Hydraulic Fracturing has been successfully introduced to take control of the timing of these caving events so as to eliminate the risk of windblast injury, The longwall face area is completely evacuated during the treatment. Water is pumped into an injection point located in the conglomerate strata above the standing goat. A horizontal fracture is generated and grows outward from the in point, separating the conglomerate strata below the fracture horizon_ At some point the strata can no longer span and a goat fall is initiated. After a treatment, mining can be recommenced with the windblast hazard eliminated.

Jan 1, 2000