Search Documents

By Robert B. Francini

Longwall mining and pipelines have coexisted since longwall mining was introduced into the United States. How the pipeline operator reacts to longwall mining under their line depends on many factors. This paper outlines the process the pipeline operator goes through to determine the appropriate response when their pipeline is being undermined. Typical mitigation procedures are reviewed. Finally, the paper looks at current design practices for new pipelines that are expected to be undermined during their lifetime.

Jan 1, 2011

By Anthony S. Spearing

The vast majority of the estimated 100 million rock anchors installed in mines in the USA per year use resin cartridges (Tadolini and Mazzoni, 2006). About 4.5 million per annum of these are bolts with a mechanical shell that if properly installed become effective active supports on installation. In addition, cable anchors (mostly passive) are installed with typically 4 ft of effective resin anchorage length sometimes with mechanical shells, which further makes the installation more difficult. This is because the cable (even with a stiffener tube) is not very rigid. When installing bolts with mechanical shells and cable bolts in the holes, the back-pressure can be so high that the installation is unsuccessful often creating a ?spinner? (an un-tensioned bolt) at best or buckling the bolt thus requiring another bolt/cable to be installed, or leaving a poorly functioning unit. The installation problems can create a significant potential safety hazard and waste time and money. Using a purpose designed test rig that physically inserts different rock anchors into pipes with resin and measure the back-pressure developed with time during the insertion/ installation. The test installation procedure is designed to mirror that used underground by rockbolt operators in coal mines. In addition a computer model has been calibrated that can predict the approximate back pressure of new anchor and resin combinations acting as a screen before physical testing. This research has lead to an understanding and quantification of the insertion back-pressures and this already resulted in improved prototype designs that could lead to more reliable mechanical shell and resin bolt installations.

Jan 1, 2009

By William Kendall

INTRODUCTION Stillwater Mining Company, with its two underground, hard rock mines in South Central Montana, is the largest primary producer of palladium and platinum in the Western Hemisphere. Platinum Group Metals (PGMs) are mined from a specific zone within the Stillwater Complex, a layered mafic/ultramafic igneous intrusion, named as the J-M Reef. Over much of the J-M Reef, the economically minable, mineralized horizon is contained at typical horizontal widths of 6.5 ft to 8 ft wide. This feature of narrow mining widths has made it challenging to safely and effectively mine these areas of the J-M Reef using mechanized cut and fill and sublevel sill development mining methods. Mechanization of most or all of the steps of the mining process is important to Stillwater in the continuous pursuit of high standards in safety and health. Mechanized bolting within the J-M Reef ore production headings is an important piece of reaching these objectives. In general, metal/non-metal mining requires varied mining techniques, as compared to more traditional bedded mineral/resource deposits. Narrow vein mining is a selective mining technique that generates a minimal amount of waste material while obtaining the more valuable ore deposits. Drilling and bolting in narrow vein mining has traditionally been performed with air-powered, hand-held ?jackleg? equipment because mechanized equipment is, typically, too large for the selective narrow vein techniques. In addition, traditional hand-held pneumatic equipment provides significant flexibility for small-opening, narrow-vein developments, reducing waste rock handling and improving ore recovery management. The hand-held equipment is also relatively inexpensive to purchase. Due to its simplicity, it is also relatively easy to train operators to use hand-held equipment. Hand-held equipment has been routinely used to safely install ground support and to develop production faces in hard rock mines for many years. Although it is effective, the hand-held equipment requires operator exposure to certain inherent hazardous conditions in the active face/development mine areas. These include falling rock, tripping hazards, bending/twisting/lifting hazards, high noise levels, and chemical fumes from the hammer exhaust. Based on health and safety statistics from the Stillwater mines, operation of the rotary-percussive hand-held equipment adversely affects the long-term health of the operator?continual jackleg operation frequently results in long term damage to hearing, shoulders, arm and wrist joints, and back injuries. This reduces the quality of life for the operator and also results in higher personnel turnover rates for the mining company.

Jan 1, 2014

By Behdeen Oraee, Amirhossein Bangian, Kazem Oraee

"Determination of the optimum design of chain pillars has a significant effect on the economics and safety of longwall operations. Most pillar design formulae are based on empirical methods and supplemented by local experience. They therefore lack versatility of application under different geotechnical conditions.In this paper, in order to illustrate the shortcomings of the above, a typical real coal pillar in Tabas coal mine has first been studied and the conventional formulae have been used to determine the optimum dimensions. The results show that a wide difference exists between the predicted and the real field data. The Oraee-Hosseini formula has then been applied to this mine in order to determine the optimum design. The results from this formula demonstrate a close fit between the theoretical VALUES (and those produced by laboratory tests and in practice. It is further demonstrated that the wide discrepancy between the results obtained from the two formulae is attributed to the dissimilarities between geotechnical conditions of Tabas and the original regions whose data were used to devise the empirical formulae.It is finally concluded that the application of numerical simulation methods and experimental equations together with engineering judgment used by the mining design engineer, will provide the most accurate design characteristics.INTRODUCTIONLongwall is an underground mining method which has a high rate of production capacity and mechanization ability. This mining method, which is appropriately applied for soft rock fiatlying bedded ore bodies, gradually became a widespread mining method amongst European coal mines at the beginning of the 19'h century. It was then applied in some of the U.S. coal mines with the development of self advancing support mechanisms in early 1960's (Oraee, 2001).Underground coal production around the world using Longwall mining method doubled during 1990s. The main reasons for this improvement were: the high level of mechanization, increased 10 safety, adequate design of panels, and well designed ventilation systems (Peng, 2006)."

Jan 1, 2010

By Gautam Benerjee, Veera Reddy Boothukuri, Bhattacharjee Ram Madhav, Panigrahi Durga Charan

"India’s tryst with mechanized longwall coal mining started with the introduction of the first self-advancing powered support longwall (PSLW) face at Moonidih Colliery of Jharia Coalfield in 1978 and at Godavarikhani (GDK)7 Incline of Singareni Collieries Company Limited (SCCL) in 1983. During the last 37 years, about 30 longwall units in Coal India, Ltd., (CIL) and 10 longwall units in SCCL have been introduced with powered roof supports of varying capacity, ranging from 280 to 800 tonnes, in many mines in India under varying geological and geotechnical conditions. The majority of the longwall faces in India have been worked under relatively shallow cover (up to 200m), and significant strata control problems have been encountered due to poor caveability of the roof, inadequate capacity of the supports, a lack of knowledge on longwall caving mechanisms, less than adequate strata monitoring systems, and the non-availability of quality spare parts, etc. This has resulted in structural damage to supports and increased downtime of the equipment, thereby making longwall mining in India a case of technology failure. Energy demand for a developing country like India with a population of 1.2 billion is huge, and the thrust on increasing coal production continues. However, the share of coal production from underground mines in India continues to decline (current share is around 6%) because of absence of successful mass production technology in underground coal mining. Under this backdrop, a high-capacity longwall with state-of-the-art technology was introduced in 2014 at Adriyala Longwall Project (ALP) of SCCL for the first time in Indian Coal Mining Industry. The first longwall panel (LWP) has been completed successfully. This paper highlights the major geotechnical challenges encountered during development of the longwall gate roads due to the presence of two overlying clay bands, significant in-situ horizontal stresses and the experience of using rigid (welded) steel wire mesh with resin-anchored roof bolts. Efforts have been made to analyze longwall weighting and caving behavior, such as main and periodic weightings, the effect of front and side abutment pressures, and the behavior of gate roadway support systems under immediate friable weak roof with overlying massive sandstone."

Jan 1, 2017

By Alan D. Smith

[A standardized checklist in a questionnaire format, was established to investigate selected factors associated with coal nips roof falls, as derived from an intensive review of the literature. A plot study was undertaken to aspect and explore possible statistical relationships that may exist with these parameters. the Purposes of toe study were to: 1. Study in a systematic and empirical fashion selected parameters that may be capable of differentiating characteristics of roof falls; 2. Obtain some predictive indices cased on selected physical and management related variables so that predictions of future problems associated with mine roof falls can be completed, prior to its actual occurrence. Accomplishment of these goals should result in valuable guides to the mining engineer in scheduling exploration work and 4 determining economic feasibility of certain ground control and .lining pro and practices. The parameters associated with mine roof failure that where included in the questionnaire are: working section, county, spar., orientation degrees), pillar dimensions width, length), seam thickness, roof fall dimensions (length, width, surface area, volume), shape of fall (arch, dome, laminar), thickness of thinnest immediate layer, lithology of the first four i.e.-diate roof layers, thickness of h e first four immediate roof layers, type of initial support systems before failure, type of resupport system after failure, length and spacing of bolts in use before failure, length and spacing of bolts planned after allure, presence of .cater, time failure after It coal excavation, distance t3rest ace, physical operation during, time of coo failure, location of the roof fall entry failure occurred ence of sloughing of ribs before failure, and presence of floor heave condition before failure. The typical roof fall had an average roof spar of 20.3 feet, -06 feet depth o coal seam, occurred 136 feet from nearest face, coal seam thickness of inches, p--ar :width off 45 feet surface area D' roof fall 1151 ft2, mainly lamin- shaped, previously rat fore fall between good to very good, little floor heave presence, usually cracks before the fall about 40 percent of reported cases, shales in most of the immediate layers, and usually located in an entry or intersection. in addition, multiple linear regression techniques were employed in the testing process of 18 major research hypotheses in a search for relationships among the various parameters studied of which were found to be significant, once corrected for multiple comparisons.]

Jan 1, 1984

By Y. L. Sun

The feasibility of using the ultrasonic wave attenuation method for measuring in-situ stress is examined theoretically and experimentally. The theoretical analyses show that for a given rock type the relation between stress and attenuation coefficient ratio can be approximated closely by second-order polynomials. Combining the elastic and statistical theories, the magnitude and direction of the existing principal stresses can be predicted by using the relations between stress and attenuation coefficient ratio obtained in the calibration of core specimens. Several experiments are conducted in the laboratory on two types of rock. The experimental study consists of two parts: the attenuation-coefficient measurements in core specimens under uniaxial stress and the attenuation coefficient measurements in boreholes drilled through blocks of sandstone and limestone subjected to uniaxial compressional stress. Compressional waves are used exclusively in the measurements.

Jan 1, 1989

By L. J. Terrill

Lateral displacement in the immediate roof beam at the Waste Isolation Pilot Plant (WIPP) is a significant factor in assessment of excavation performance for the design of ground control systems. Information on roof beam lateral displacement, expansion, fracture formation, as well as excavation convergence, is gathered using a variety of manually and remotely read instruments. Visual observations are also used when possible. This paper describes the methods used to measure lateral displacement, or offset, at the WIPP. Offset magnitudes are determined by the degree of occlusion in drillholes that intersect the offset plane. The Borehole Lateral Displacement Sensor (BLDS) was developed for installation at WIPP to monitor offset at a high degree of accuracy at a short reading frequency. Offset measurements have historically been obtained by visual estimation of borehole occlusion. Use of the BLDS will enable relationships between time dependent roof beam lateral displacement and expansion to be established in much shorter periods than is possible using visual observations. The instrument will also allow remote monitoring of roof beam displacement in areas where visual estimations are not possible. Continued monitoring of roof beam displacement, convergence, and expansion, is integral to timely and pertinent assessments of WIPP excavation performance.

Jan 1, 1996

By Dakota Faulkner

Unexpected roof falls often occur in the entries or intersections of active mining sections in underground mines. For large roof falls (greater than 20 ft in height), it becomes dangerous and impractical to clean up the rock debris and re-bolt the newly exposed roof strata. To help mine operators rehabilitate the roof fall areas in a quick, safe, and economic manner, Jennmar Corporation and Keystone Mining Services, LLC (KMS) designed, tested, and developed various impact-resistant (IR) steel set designs, as initially detailed in the proceedings of the 30th International Conference on Ground Control in Mining (ICGCM). Since then, the IR steel sets have been successfully installed in more than 100 roof falls in 43 different coal mines. Significant data has been obtained from these installations, enabling further refinement to and improvement on the design. This paper (1) updates drop test results of the IR lagging panel, (2) presents a case study of the performance of IR arch sets installed 56 months ago at a roof fall rehabilitation site, (3) demonstrates capacity evaluation of the IR steel set, and (4) outlines a preliminary applicability evaluation guideline of the IR steel set for a given roof fall condition. Field evaluation and structural numerical analysis indicate that impact capacity of the system is significantly higher than that of the IR lagging panel, as originally determined. It is concluded that, when evaluating the applicability of an IR steel set, ground control engineers should consider the IR lagging and steel set as an entire system and make a reasonable engineering decision based on actual roof fall geotechnical conditions.

Jan 1, 2014

By Ihsan Berk Tulu, Michael Sloan, Ted Klemetti, Michael M. Murphy, Gabriel S. Esterhuizen, Jame Sumner

"In this paper, the advantage of using numerical models with the strength reduction method (SRM) to evaluate entry stability in complex multiple-seam conditions is demonstrated. A coal mine under variable topography from the central Appalachian region is used as a case study. At this mine, unexpected roof conditions were encountered during development below previously mined panels. Stress mapping and observation of ground conditions were used to quantify the success of entry support systems in three room-andpillar panels. Numerical model analyses were initially conducted to estimate the stresses induced by the multiple-seam mining at the locations of the affected entries. The SRM was used to quantify the stability factor of the supported roof of the entries at selected locations. The SRM-calculated stability factors were compared with observations made during the site visits, and the results demonstrate that the SRM adequately identifies the unexpected roof conditions in this complex case. It is concluded that the SRM can be used to effectively evaluate the likely success of roof supports and the stability condition of entries in coal mines.INTRODUCTIONSince the introduction of roof bolts in the coal mines during the late 1940s and 1950s, roof bolts promised to dramatically reduce roof fall accidents (Mark, 2002). However, ground falls still remain a significant factor in underground coal mine injuries and fatalities. In 2013, ground falls accounted for 4 of the 14 fatalities and 166 of the 1577 reported lost-time injuries in underground coal mines (MSHA, 2015).The design of appropriate support systems requires the understanding of: 1) the variable nature of the rock mass, 2) the performance and characteristics of the roof support, 3) the interaction between the rock mass and the installed support system, and 4) the in-situ and mine-induced stress distribution around the excavation. Over the past 25 years, multiple design approaches have been used in coal mine ground control. The approaches include empirical mechanistic methods, empirical statistical analysis, rules of thumb, and numerical methods (Hebblewhite 2006). In the U.S., Analysis of Roof Bolt Systems (ARBS) can be given as an example of an empirical method. ARBS uses relatively simple equations to calculate the intensity of support provided by a roof bolt system and compares it with a suggested ARBS value (Mark et al., 2001). The suggested ARBS design equation is derived from an analysis of 100 case histories. The ARBS design equation is dependent on two parameters: depth of cover and Coal Mine Roof Rating (CMRR). More recently, a probabilistic design approach was developed by Canbulat and van der Merwe (2009) in South Africa. In this method, the variability of the rock mass, the mining geometry, and support characteristics are included in the analytical models. The major advantages of these two methods are: 1) they can be applied rapidly and easily, 2) complex rock mass/ roof support interaction mechanisms are represented with simple equations, and 3) they are supported by large databases. However, both methods generally ignore mining-induced stress distribution, details of the roof support system, details of the geological setting, and the interaction between the support system and the rock mass."

Jan 1, 2015

By Liane J. Terrill

Rockbolt failures at the Waste Isolation Pilot Plant have been recorded since 1990 and are categorized in terms of mode of failure. The failures are evaluated in terms of physical location of installation within the mine, local excavation geometry and stratigraphy, proximity to other excavations or shafts, and excavation age. The database of failures has revealed discrete areas of the mine containing relatively large numbers of failures. The results of metallurgical analyses and standard rockbolt load testing have generally been in agreement with the in situ evaluations.

Jan 1, 1995

By Christopher Mark

A coal burst is defined as the sudden, violent ejection of coal or rock into a mine opening. Coal mines in the North Fork Valley (NFV) of Colorado?s Gunnison River have a long history of coal bursts in a wide variety of settings. These have included longwall and room-and-pillar, development and retreat, and single- and multiple-seam mining. In contrast to other coalfields, where bursts are typically associated with strong, massive sandstone and extremely high stress, many bursts in the NFV have occurred beneath shale roof and some distance from the most highly stressed locations. The goal of this paper is to attempt a systematic study of the entire burst history in the NFV, in order to gain insight into their characteristics and causes. The primary sources of information are the reports of investigations conducted by the Mine Safety and Health Administration (MSHA) Roof Control Division over the past 15 years. This paper provides details on the geologic mapping conducted as part of these investigations, as well as a regional plot of burst locations using a Geographic Information System. The mapping indicates that many of the NFV bursts have been associated with structural features, including low-angled faults and well-defined zones of high-density jointing that exhibit little or no displacement. Some of these features appear to extend for several miles, impacting more than one mine.

Jan 1, 2012

By Yuanwci Shi

This paper discusses the results of research on the interaction between roof strata and shield supports including the active and passive supporting functions of the shield supports which prevents roof strata separation; pressure distribution on the canopy and under the base plate as measured in the laboratory and underground; comparison between various shield structures regarding their effectiveness on roof and floor control; and determination of optimum support capacity under given geological and mining conditions including hard-tocave roof

Jan 1, 1997

By Peter Zhang, Dan Neilans, Scott Peterson, Scott Wade, Joe Pugh, Ryan Mcgrady

"A coal outburst is a severe safety hazard in room-and-pillar mining under deep cover. It is more likely to occur during pillar retreating. Multi-seam mining dramatically increases the risk of coal outburst within the influence zones created by remnant pillars and gob-solid boundaries. Though coal outburst is generally associated with heavy loading of coal pillars, its occurrence is difficult to predict. Risk management provides a proactive tool to minimize coal outburst in room-and-pillar mining under deep cover. Risk assessment is the first step in identifying and quantifying outburst risk factors. The primary risk factors for coal outburst are overburden depth, roof and floor strength, geological anomalies, mining type, multi-seam mining, and panel width. A risk assessment chart can be used to proactively screen out mining sections with high risk of coal outburst for further analysis. Gob-solid boundaries and remnant pillars are critical factors in evaluation of the coal outburst risk of multi-seam mining. Risk identification, risk assessment, geologic influence mapping, geotechnical evaluation, risk analysis, risk mitigation, and monitoring are essential elements of coal outburst risk management process. Training is an integral part of risk management for risk identification and communication between all the stakeholders including management, technical and safety personnel, and miners.INTRODUCTIONA coal outburst is a sudden violent burst of coal from a pillar with broken coal or blocks of coal forcibly ejected into open entries. A coal outburst is a severe safety hazard as the mining crew is highly exposed at the site when the event occurs. Though deep cover and strong roof and floor are underlying geologic conditions of a potential burst incident, its real occurrence is also the result of additional mining factors. In room-and-pillar mining, a coal outburst could occur during both development and pillar retreating, but the latter greatly increases the risk of outburst. The other risk factors of coal outburst also include mining layout, multi-seam mining, presence of adjacent gob, cutting sequence, and local abnormal geologic conditions. Over the years, the cases of coal outbursts have been studied by many researchers and mining practitioners(Peng, 2008; Newman, 2008; Iannacchione and Tadolini, 2008; Gauna and Phillipson, 2008; Hoelle, 2008; and Newman, 2002). It is commonly believed that the coal outburst is the result of a sudden release of elastic strain energy stored in coal pillars and is highly associated with cutting into heavily loaded coal pillars, but its occurrence is a rare event and is difficult to predict. A number of engineering controls have been recommended to mitigate outburst potential. For room-and-pillar mining, sufficient pillar sizes have been the primary control for coal outburst prevention. The pillar design tools such as ARMPS and AMSS developed by NIOSH have played an important role in the design of stable pillars to prevent pillar collapse and squeezing as well as coal outbursts. In fact, with the implementation of pillar design using proper stability factors, pillar collapse and squeezing have been almost eliminated, and the number of coal outbursts has been greatly reduced in the US over the past decade. However, after a few outbursts occurred during pillar retreating in the US over the past a few years (MSHA, 1996; MSHA, 2014; MSHA, 2013), it has been realized that sufficient pillar size is still not enough to prevent coal outbursts. The investigations of the incidents showed that other factors such as multi-seam mining, panel layout, cutting sequence, and local geologic factors also seemed critical in causing the events. Therefore, it has become imperative that additional proactive measures beyond proper pillar design be implemented to prevent coal outbursts."

Jan 1, 2015

By Ke Yang

In Chinese coal mines, extraction of deep, highly gassy soft coal seams sandwiched between soft floor and soft roof in complicated geology is commonly encountered. How to safely and efficiently excavate such seams is a very significant and important problem. It has been a focused research area in recent years. By combining the characteristics of fully mechanized longwall mining methods such as large cutting height and mining along the dip, an integrated method and technologies for the Zhangji Coal Mine were developed. This technology includes the design of a complicated geological exploration system, optimization of mining method and working face parameters, control of rock pressure and high levels of gas, reliability model of the production system, and selection and compatibility of equipment. Engineering practice shows that the integrated technology was successful in mining these complicated seams. This study not only enriches the mining method, but also improves the coal mining practice, especially ensuring both safety and productivity under complicated geological conditions.

Jan 1, 2009

By M. J. Beus

This paper will describe the research approach being initiated by the Spokane Research Center to assess hazards and design criteria to prevent ground and muck falls in and around ore passes in hard-rock mines. The major goal of this research is to compile detailed information about ore pass processes and hazards, identification and testing of prevention strategies, and development of computer-based measurement and design methods. Recent ore pass failures have underlined the lack of OE pass design capabilities and standards available to both mine engineers and MSHA personnel. Design criteria and ore pass hang-up prevention and remediation strategies will include the effects of internal ore pass loads, blasting to relieve hang-ups, and rock mass stress redistribution and structural interaction from nearby mining. New visualization and three- dimensional analysis methods will be presented as an extension of existing ore pass design and analysis techniques. A sophisticated particle-flow analysis program will be used to simulate the response of various ore pass designs to a wide range of loading conditions driven by rock mass deformation, muck flow, ore pass blockage, and blasting in both nearby stopes and the ore pass. Analysis techniques will be calibrated and design criteria validated at the Spokane ore pass test facility. These tools will serve to reduce research costs by limiting the number of experimental field tests required.

Jan 1, 1996

By Brad R. Blair

This paper will review impacts on longwall design and ground stability assessment due to advances in mine automation and sensing technology. Several new approaches to the prediction and monitoring of longwall panel and gateroad stability have recently become mature, and are ready for application in problematic ground control situations. These methods are revealing significant detail regarding deformation and failure mechanics of critical underground structures. Examples of how these technologies have worked successfully will be given, and applications for the use of these tools for cost-effective engineering design and monitoring will be suggested.

Jan 1, 1996

By Jennifer Riefenberg

Ground control hazards, coal quality, ore reserve estimation, and pollution modeling seem unrelated topics from most mining perspectives. However, geostatistical methods can be used to characterize each of these, and more topics. Exploratory drill core data, and continued drilling and field measurements, can provide a wealth of information related to each of the above areas and are often severely underutilized. Recent studies have led to the development of the Multiple Parameter Mapping (MPM) technology, which utilizes geostatistics and other numerical modeling methods, to generate a "hazard index" map, often from exploratory drill core data. This mapping has been presented for ground control hazards relating roof quality, floor quality, numerically modelled stresses due to mining geometry, and geologic features. A review of the MPM method, future directions with the MPM, and a discussion of using these and other geostatistical methods to quantify coal quality, ore reserve estimation, and pollutant modeling are presented in this paper.

Jan 1, 1996

By J. Willan

This paper addresses the problem of designing a destress blasting procedure to reduce the incidence of rockbursting in hard rock mines. A review is made of the developed theory and practice of destress blasting in rockburst-prone ground. Specific reference is made to a recent survey of past and current practice with particular reference to Ontario mining operations. The need is identified for a more scientific basis for destress blast design and monitoring. Reference to developments in blasting technology as well as rock mechanics are then made to support a proposed, integrated design procedure and research strategy.

Jan 1, 1984

Historically, the selection of mining sequence for multiple seam conditions has been based on many factors other than ground control considerations and minimization of interaction effects. Today, numerous operations are finding themselves mining above existing or abandoned operations, some of which exhibit large scale caving, pressure arches and subsidence troughs. Development of design criteria for the upper seam that would alleviate damage due to lower seam interaction effects can contribute substantially to the safety and productivity of many mining operations. The primary objective of this re search has been to identify methods of improving ground control conditions in the upper seam when mining through either passive or active subsidence waves. These methods concentrate on improved ground control practices for the upper seam, rather than reducing the amount of subsidence in the upper seams by improved practices in the lower seam. Design factors such as pillar size, pillar and opening orientation relative to the subsidence trough, offsetting intersections, and different support methods have been studied for the upper seam in a variety of typical geologic environments. Analysis has demonstrated criteria for ameliorating negative interaction effects and facillitating design in the superincumbent seam.

Jan 1, 1986