Search Documents

By John C. Stankus

The success of cable bolts for mine ground control have been well documented in papers presented at this conference too numerous to reference. Cable bolts have proven effective over the years mainly utilized in the form of supplemental support. Some limited work has been conducted on the use of cable bolts as primary support This work has been mainly confined to the West and the bolts utilized were of a non- tensioned type MSHA requirements for primary support have been that the bolt system he tensioned or if non-tensioned, then fully encapsulated with resin. Many operators are now interested in using cable bolts as primary support Further, despite the enormous success of cable bolts, there have been questions raised about the longevity and corrosion characteristics of the cable itself particularly for long tern applications. To improve the corrosion characteristics of cable bolts, galvanized cable has been used for some applications However. although improving the corrosion resistance of cable, galvanized cable for mine ground control does not provide complete protection under certain types of situations and mine environments. Realizing a need for a cable bolt that can be used for primary support and provides consistent installed tension, complete corrosion protection, and a fast installation, Keystone Mining Services. LLC (KMS), an affiliate of Jennmar Corporation, has developed the INSTáL CableOx system. This paper will detail the development and specifics of this system including two underground case studies

Jan 1, 2000

By Christopher Mark

A new method for the design of longwall pillars, called "Analysis of Longwall Pillar Stability" (ALPS), is described. The method is the final result of a research program that included two major field studies, extensive reanalysis of data from other in situ measurements, and detailed evaluations of available pillar design methods. The key problem addressed by ALPS is estimation of the abutment loads applied to longwall pillars. Based on underground stress measurements made in mines in three states, equations for predicting the magnitude, distribution, and time-of-arrival of abutment loads are proposed. Stress measurements are also used to evaluate empirical pillar strength formulas for use in longwall pillar design. ALPS has been verified by application to case histories from several mining areas, and examples taken from the Pittsburgh and the Blue Creek seams are presented. Step-by-step guidelines for using this design method are also given.

Jan 1, 1987

By G. I. Gritsko

In this paper we consider the elements of a distributed information geomechanic monitoring system which is used in computerized mine planning and mining operations control. The automated system is a technical means of geomechanic monitoring, as a complex system of regulated observations, estimation and prediction of geomechanic state of rock mass and workings during underground mining of coal deposits. Geomechanic monitoring at coal mines and the automated system execute data collection, analysis and calculations of geomechanic situation in the panel during planning, development and carrying-out of mining operations for ensuring geotechnical stability of underground mining.

Jan 1, 1996

By Alan A. Campoli

The U.S Bureau of Mines is conducting research to develop improved guidelines for selecting the type and pattern of roof support in different geologic environments (Mucho, et al., 1995). As a part of this wider research effort, a multifaceted ground control investigation was conducted at the Diamond TB Mine of RoxCoal, Inc. The study included statistical analysis of mine-wide roof bolt performance, instrumented bolt test areas, stress damage mapping, and pillar design analysis. The mine employs state-of-the-art continuous miner technology, including mobile roof supports and continuous haulage, to retreat mine the Lower Kittanning Coalbed. A herringbone section design makes the stability of the center belt entry critical to efficient retreat mining. Roof cutters formed during section development sometimes set up unstable immediate roof conditions in advance of the belt entry mobile roof supports during retreat mining.

Jan 1, 1996

By Francis Kendorski

One of the most dangerous events in underground coal mining is unexpectedly encountering water inrushes from undetected abandoned mines in the same seam. The surest and most confident method is probe drilling either from the mine or from the surface. However, drilling is expensive and may even miss the suspected mine voids entirely by drilling through pillars. Many operators rely upon one or more of several remote sensing techniques for detecting mine voids. However, mine "voids" often are not air- or water-filled open cavities, but are collapsed, rubble-filled chimneyed columns in the strata. Geophysical techniques, such as seismic reflection and refraction, electrical resistivity, magnetics, ground-penetrating radar, and others, often assume a continuous or fractured rock mass that has varying properties which provide the signatures that allow discrimination of one strata from another, or of strata from voids. However, a rubble-filled cavity has rock block-to-rock block contact throughout its volume and can still respond as a continuous rock mass with the rock blocks allowing signal transmission or mass detection, rather than a void space. Hydraulically, a rubble-filled cavity is essentially as transmissive to water as an open mine void. Thus, the problem of detecting a mine void with confidence is significantly compounded.

Jan 1, 2004

By S. P. Singh

Rockburst is a sudden manifestation of the release of elastic strain energy stored in the rock. Therefore the tendency of the rock to burst should depend upon its ability to accumulate elastic strain energy. The use of Burst Proneness Index as a simple and reliable indicator to recognize the burst prone situations in the mines has been advocated in this study. The Burst Proneness Index exhibited a strong dependence upon the brittleness, compressional and shear wave velocities and the point load strength index. It was also observed that the Burst Proneness Index increases with the increase in the strain energy per unit volume, c ressive strength and the modulus of rigidity of the rocks. In addition, important causes and the measures to alleviate rockbursts have been outlined in this paper.

Jan 1, 1986

By Peter Swanson

A seismic monitoring network has been installed in western Colorado (USA) in the vicinity of three underground coal mines to (i) distinguish and characterize seismic activity as either mining related or naturally occurring, (ii) implement a real-time event monitoring and notification tool, and (iii) collect data for use in research studies aimed at quantifying impacts from mining-related and natural seismicity. These potential impacts include dynamic rock mass failures such as coal bumps as well as strong shaking in the vicinity of critical structures such as impoundment dams, reservoirs, mine seals, mine openings, and steep slopes. Examples of two damaging seismic events are presented and the mining and geologic factors attending these dynamic failures are described.

Jan 1, 2008

By Andrzej Walentek

In polish coal mining due to specificity of seams lying the multiple extraction is used. In this kind of mining, it is essential to take into account all geological and mining conditions which have an influence on stability and functionality of workings during their using. In view of above, for one of polish coalmines, by mean of Phase2 program, the numerical calculation were made for assessment of the influence of advancing excavation front on convergence of roadway located 30 meters above longwall was analysed. In order to verify developed prognosis, in analyzed roadway the underground investigations in scope of convergence measurement and changes of load exerted on working support were carried. As a result of these investigations it was found that real convergence on certain part of roadway was significantly larger then determined in prognosis. Additional calculations and analysis showed that the main cause of differences was underestimation of influence of dynamic load, which was an effect of numerous low energetic rockmass tremors. These tremors, related to excavated longwall, were located in close proximity of roadway in its part where the biggest convergence occurred. In current practice, in this type of convergence prognosis, the maximal value of dynamic load exerted on roadway resulted from single rockmass tremor is taken into consideration. Quantitative consideration of all tremors including their location is impossible at the stage of convergence prognosis because of lack of this type of data. This paper presents results of roadway convergence prognosis compared to results of underground investigation. Conclusions formulated on that base allow in future similar designing works for obtaining more accurate results.

Jan 1, 2013

By Andre Zingano

The objective of this paper is to study the effect of annulus thickness on the quality of resin mixture for fully grouted resin bolt. Pullout and mixture tests were made in underground coal mines for the following arrangements: (a) borehole diameter 1.14 in. (29 mm), and roof bolt diameter 0.75 in. (19 mm) with steel wire around the roof bolt; (b) borehole diameter 1.14 in. (29 mm), and roof bolt diameter 0.75 in. (19 mm) with no wire around the roof bolt; and (c) borehole diameter 0.95 in. (24 mm) and a roof bolt diameter 0.75 in. (19 mm) with no wire around the roof bolt. The mixture test in steel pipe showed that the best resin mixture is for borehole with 0.95 in. (24 mm). The arrangement (b) produced big voids around the bolt. But for the 0.95 in. (24 mm) hole, arrangement c, the mixture was the best. It was corroborated with the pullout tests results where there is a difference in grout stiffness: the 0.95 in. (24 mm) borehole is about 10 times higher than a borehole with diameter 1.14 in. (29 mm). On the other hand, for the cohesive strength the difference is not significant. Numerical models were built to simulate the pullout tests, and also to simulate the roof support at an intersection. Convergence at two underground intersections, consisting of an immediate roof with laminated sandstone, was monitored to evaluate the performance of the roof supports, using the 1.14 and 0.95 in. (29 and 24 mm) diameter boreholes (i.e. arrangements ?a? and ?b?). The convergence readings showed that the 0.95 in. (24 mm) borehole diameter resulted in a smaller, although it was not significantly different.

Jan 1, 2008

By Miklos D. G. Salamon

If all stratifications are horizontal, the computation of surface deformation induced by coal mining involves the prediction of roof and floor convergence and then the transfer of the effects of this relative displacement to the surface through the use of the appropriate influence functions. A laminated model, in the form of a quasi- continuum, provides a simple means of computing the approximate convergence distribution and leads to the Gaussian distribution as the influence function. The ideas presented in this paper represent a subtle but fundamental generalization of the influence function Method. It is postulated that the influence of a small area of extraction is proportional to the roof and floor convergence and not to the thickness extracted. This difference in definition removes many conceptual difficulties associated with the influence function method. To demonstrate the utility of the model, the surface disturbances induced by the extraction of a parallel sided long panel are derived. Formulae giving subsidence, tilt, horizontal displacement and strain are given.

Jan 1, 1989

By Witold M. Pytel

A simplified, three-dimensional, time-dependent, mechanistic model of the overburden-coal seam-floor interaction has been developed and validated at two Illinois coal mines. The model based on the thin plate theory can involve any complex layout of mine workings, time-dependent sequence of extraction and, rheological properties of immediate floor strata. The model output data consist of spatially distributed surface subsidence and its slope and curvature, as well as load acting on pillars in one or more panels. A comparison of calculated and monitored surface subsidence or in-mine convergence measurements has proven the model's effectiveness for surface subsidence and load transfer prediction.

Jan 1, 1992

By T. P. Mucho

Over the past several years, two types of roof control problems have been en- countered at Beth Energy's Eighty Four Complex mine in Southwestern Pennsylvania. These problems have been (1) poor roof conditions encountered while advancing submain entries and longwall panel entries and (2) deterioration and failure of long- wall gateroads, principally the tailgate entry. This paper discusses the efforts by mine personnel to analyze the origins of the various attempts to-deal with the problems, and the success (or failure) of these efforts. Highlighted are the use of various common roof Control materials, variations in mining techniques, cementatious pillars, and changes in pillar design using yield and abutment pillars to address these problems.

Jan 1, 1986

By D. F. Scott

Seismic tomography, as used in mining, is based on the principle that highly stressed rock will demonstrate relatively higher P-wave velocities than rock under less stress. A decrease or increase in stress over time can be verified by comparing successive tomograms. Personnel at the Spokane Research Center have been investigating the use of seismic tomography to identify stress in remnant ore pillars in deep (greater than 1220 m) underground mines. In this process, three-dimensional seismic surveys are conducted in a pillar between mine levels. A sledgehammer is used to generate P-waves, which are recorded by geophones connected to a stacking signal seismograph capable of collecting and storing the P-wave data. Travel times are input into a spreadsheet, and apparent velocities are then generated and merged into imaging software. Mine workings are superimposed over apparent P-wave velocity contours to generate a final tomographic image. Results of a seismic tomographic survey at the Sunshine Mine, Kellogg, ID, indicate that low- velocity areas (low stress) are associated with mine workings and high-velocity areas (higher stress) are associated with areas where no mining has taken place. A high stress gradient was identified in an area where ground failed. From this tomographic survey, as well as four earlier surveys at other deep underground mines, a method was developed to identify relative stress in remnant ore pillars. This information is useful in making decisions about miner safety when mining such ore pillars.

Jan 1, 1996

By Wouter Hartman

Xuandong Coal Mine is mining coal in one of the most challenging underground environments in the world. This work has found that it is not only challenging but it also has the composition for some interesting rock mechanics and ground control conditions. The paper highlights the extreme mining and rock mass behavior conditions encountered when mining coal at 900 m below surface. It was found that the ground control environment associated with geological weakness, low coal material strength and stiffness, was reasonably well controlled; however, the chain pillar geometry and design did not take these geological weaknesses into consideration. Some of the chain pillars employed were quite large, which resulted in floor punching and secondary floor heave, which causes extreme difficulty for production. No barrier pillar has been employed except for the center 164-m-wide main headings pillar with a w/h ratio in excess of 40. After assessing the location and geometry of a 200-m-thick dolerite sill overlaying the coal measures, we found the probability of it breaking up into to smaller fragments and producing a larger goaf to be low. Therefore, the influence of the dolerite sill on chain pillar loading is considered small compared to the low coal, immediate floor and roof rockmass strength. It is further recognized that horizontal stresses could be locked up within the dolerite sill, which would likely result in regional bending that would be distributed through the chain pillars. This has, to some extent, already occurred, and the effects have been seen and felt through excessive floor heave, pillar punching, and coal bumps (seismicity). We?ve also found that there was a need to employ basic rock mechanics principals in assessing the stability of future multiple seam mining layouts.

Jan 1, 2012

By M. Y. Fisekci

This paper concentrates on subsidence measurements, applied over the thick and steep seam mining in the Rocky Mountains Region of Western Canada. The studies to date indicate that two new subsidence monitoring techniques appear to be the most suitable methods for these conditions. The computerized telemetry and aerial photogrammetry systems are being tested for the reliability of the systems during the winter months within the net- work of laser surveying over the workings of the new hydraulic mine.

Jan 1, 1981

By Holger Witthaus

There is more than a century of experience in multiple seam mining in Germany. In several mines up to 20 seams had been excavated within the last decades. Due to the nature of the deposit and the history of technical development the older panels cause a complex stress distribution for the lower seams and the current longwalls in descending order of mining. The depth of the longwalls reaches up to 4000 ft. This causes a maximum vertical stress that reaches between 30 and appr. 60 MPa. To handle these conditions several support systems are applied for roadway heading. A central knowledge management system for ground control is used for design and dimensioning of support within the DSK. This paper gives an overview to the nature of German multiple seam mining and the solutions in matters of panel layout and support design. It describes the full lifecycle for roadways in the seam starting with the geological and geotechnical evaluation, the basics of roadway deformation in great depth, the development of planning tools and standards for German coal mines, the range of alternative of support systems and roadheading techniques, as well as the reinforcement measures and the processing of support at the T-junction of the face entry. This paper uses exemplary descriptions that are consolidated in a specialized reference book ?Gebirgsbeherrschung von Flözstrecken? ? ?Ground Control in Roadways? which summarizes the standards of ground control based on the development of the past 25 years in German coal mines.

Jan 1, 2007

By W. J. Mcgaughey

A crosshole seismic imaging (tomography) experiment has been carried out in an underground mine in order to delineate waste rock within a massive sulphide ore body. Data comprising 1526 travel time measurements were inverted to yield a compressional wave speed image consistent with, and adding to, knowledge of the extent of the waste inclusions. An effective method of resolving travel time discrepancies measured on reversed ray paths is presented.

Jan 1, 1989

By Frank E. Chase

Clay veins, also referred to as clay elastic dikes, have been responsible for numerous underground injuries and fatalities. These hazardous structures are also responsible for increased production costs during all phases of mining. For these reasons, the Bureau of Nines has investigated the physical characteristics of and roof instability problems associated with clay veins in order to make support and other mining recommendations. In addition the occurrence and origins of clay veins were examined to determine whether or not the structures could be projected into unmined portions of the coalbed. This investigation included portions of the Arkoma, Illinois, Northern Appalachian, Southern Appalachian, and Uarrior Coal Basins. Virtually a11 clay veins observed or documented occurred in the Illinois and Northern Appalachian Basins. Observed clay veins ranged in sire from 1 inch to 16 feet In cross-section and were found under shale, siltstone, sandstone, and limestone roof rock. Individual clay veins were predominantly composed of claystone; however, limestone. siltstone. and sandstone infilled clay veins do occur. Clay vein formation has been associated with the infilling of fissures which result from compressive, tensile, or shear ground failures. These gaping fissures were propagated by compactional processes and/or tectonic stresses active during and subsequent to coal iff cation. Associated fault, fracture, and slickenside planes commonly parallel clay veins and disrupt the lateral continuity of the immediate and, sometimes, main roof. When clay veins parallel or subparallel the direction of face advance the roof is segmented into cantilever beams causing unstable conditions. Therefore, the strata on either side of the clay vein must be bolted and strapped together to form a beam.

Jan 1, 1984

By Xinxian Zhai

Jining No. 3 Coal Mine, a subsidiary of Yanzhou Coal Company Limited. China, is a super-large modern mine. The coal mine is not only the first one constructed with five-million tons of designed production capacity in China, but also a modern underground coal mine with coal transportation systems by trains and ships, and with a power plant. Based on the hard roof conditions of the sublevel caving coal face in the fault-affected zone, the authors designed rebar and cable bolts for supporting the tailgate that is separated from the gob by a narrow pillar. With extensometers and borescope, strata behavior was systematically studied during tailgate development: (1). Roof convergence is much smaller as well as roof strata separation between inside and outside the anchored zone. (2). The affected zone during tailgate development is approximately 50 m. (3). Because of serious floor heave and obvious rib convergence, the tailgate finally turned into a reversed-trapezoid from the original rectangular shape. (4). There being many joints and fractures in the pillar, coal is crushed from the elastic bedded structure into loose blocky materials. But the tailgate met the service requirements during longwall retreat mining, and demonstrated that the method of roof support was a success. Since then, roof bolting has been widely used for the tailgate of longwall panels at Jining No. 3 Coal Mine. Keywords: coal mine; bolt supporting; tailgate; convergence of surrounding rock; ground control; strata behaviors.

Jan 1, 2007

Researchers from the National Institute for Occupational Safety and Health's Spokane Research Laboratory installed Split-Set rock bolts instrumented with strain gauges to document the mechanical load response of the bolts in weak ground. Short-term monitoring of the bolts immediately after installation showed that some of the gauges went into tension. It was felt that the force exerted on the bolts to drive them into the hole should have caused the gauges to show compression. The tension probably resulted from the holes having crooked sections. Long-term monitoring over the course of a year also showed that the bolts were bending at some locations and that loads as high as 98 kN (22,000 Ib) were recorded along sections of the bolts. Load cells were placed on the head end of the bolts to determine head loads. Head loads up to 14.7 kN (3,300 Ib) were generated during bolt installation. In addition, closure readings were taken across the drift to determine the convergence rate responsible for bolt loading. A Rock Mass Rating (RMR) was calculated at the site to compare with bolt response. The bolts were installed as part of the rebolting process in an area being repaired because the near-vertical beds in the walls were buckling and causing the wall to fail. The instrumented Split-Set rock bolts will provide data that will lead to greater understanding of the behavior of the rocklbolt support mechanism. It may also be possible to explain the overall performance of the bolts in situ in terms of their design effectiveness. This work showed that load at the head of a Split-Set rock bolt was less than load along the interior of the bolt.

Jan 1, 2005