Search Documents

By Swapan Bhattacharya

United States federal and state regulatory authorities require underground mine operators to adopt adequate measures to minimize material damage to the surface caused by nine subsidence. This paper presents an approach to define and determine the extent of material damage due to subsidence from underground coal mining. The basic steps involved in the development of adequate criteria have been enumerated together with the approaches and methodologies used.

Jan 1, 1984

By Dieter Wittenberg

The use of thc ultrasound technique for monitoring rockbolt support has at last provided support engineers with a measunng system capable of pinpointing fracture failuns in fully-grouted rockbolts. The measurement data are based on the operatmg characteristics of the bolt type, which are determined both under test-bench conditions (DIN 21521) as well as in underground trials. Practical experience acquired to date suggests that this new measuring system is both effective and reliable.

Jan 1, 2001

By Richard E. Gray

Subsidence due to coal mining is poorly understood by non-specialists. This has led to numerous misconceptions and myths based on limited observations and lack of knowledge. The three most common are: 1. Mine maps are inaccurate. 2. Deep mines are not a problem. 3. If no subsidence has occurred for many years after mining, there is no risk of future subsidence. Maps are important during mining and most are carefully prepared. Future use to evaluate conditions at mine level often includes drilling to confirm what the map shows. Usually, little or no effort is made to tie the surface survey of the property to the mine survey, to conduct a well designed drilling program to confirm the mine map, or to drill test borings vertically. When a mine entry is encountered rather than a coal pillar, or vice versa, and conditions at mine level appear different than anticipated, the first reaction is the mine map is inaccurate. The idea of a safe depth from subsidence is often based on the false premise that mining results in sufficient breakup of the overlying rock strata that bulking compensates for the coal extracted. The safe depth idea first appeared in the literature about 1880 and remained prevalent well into this century. Sadly, it is still encountered. The modern understanding of fragmentation of the immediate mine roof with the overlying beds sagging down on the broken roof rock was first described in 1900. With full extraction mining, either longwall or retreat room and pillar, surface subsidence occurs regardless of the depth of the mine. Subsidence over longwall mines at depths of 2000 feet can be 90 percent of the mined seam thickness. Numerous studies of undermined sites conclude that mining occurred many years ago and since no subsidence has occurred, there is no risk of future movement. This is true if sufficient coal pillars have been left to support the overlying strata. However, every year subsidence occurs over mines that have been closed for 100 years or more. In a study of subsidence incidents over the Pittsburgh Coal, the senior authors found that 50 percent of the incidents occurred above mines that had been closed for at least 50 years and 10 percent over mines closed for at least 80 years.

Jan 1, 1996

By S. P. Singh

Drifts are an integral component of underground mining. They provide access for men and material, means for transporting ore and rock and serve as air passageways. In view of their importance on the overall safety, economy and productivity of mines, empirical guidelines for controlled blasting design in drifts have been developed in this study. The application of the proposed concept was described by generating blast hole patterns for a mine with the help of a computer program. The mechanism of blast damage and the need for controlled blasting to alleviate ground control problems in underground mines have been outlined in this paper. The economic analysis between normal-and controlled blasting was performed based on the information from an operating mine. In addition, the review of drift blasting practices and problems in Canadian mines was also carried out in this study.

Jan 1, 1990

By Thomas M. Barczak

This report chronicles the historical development of longwall mining in the United States and speculates on future developments to the turn of the century. Five eras of technological development during the modern period are described and analyzed. These eras discuss the development of (1) mechanized extraction, (2) self advancing roof supports, (3) high capacity roof supports, (4) shield supports, and (5) system automation. Current trends are analyzed in terms of: longwall utilization, production capability, support capacity, face widths, and new technological developments. From these analyses, the future of longwall mining to the year 2000 is speculated. It is concluded that longwall mining will continue to grow in importance during the next decade and that the next major technological milestone will be the realization of a fully automated longwall mining system.

Jan 1, 1992

By Victor V. Nazimko

Long term stability of the pillars that have been remained after R&P extraction causes postponed subsidence. To prevent unforeseen subsidence and to diminish postponed subsidence 25-50% new method for its control has been developed by the author. It supposes to use drilling and blasting technology and other original approaches. New method has been fulfilled through the holes being drilled from the surface or from the active underground openings. Explosives had been charged into the holes and were blasted. This had increased bulking factor dramatically and prevented natural caving of the strata. Physical scale modeling corroborated efficiency of the new approach. The bulking factor has grown from 0.0623 to 0.1185 and surface subsidence has been diminished from 1.1 m to 0.2 m or 5.5 times.

Jan 1, 1996

By Steve Tadolini

Underground roof falls can have devastating effects on the safety of operations personnel, and equipment, and seriously impact production. Immediate steps are usually taken to danger off and secure the area while clean-up efforts are designed and implemented. A critical step, often overlooked due to production demand, is the determination of - why the roof fall occurred so that additional occurrences can be avoided in future developments or what measures can be taken to identify areas that have similar ?symptoms?? Forensic engineering includes the investigation of materials, products, structures or components that fail or do not operate/function as intended. The authors define forensics in ground control engineering as the study of evidence discovered while examining underground roof falls by applying expert observational techniques and established mining engineering principles to determine the probable cause, hypothesize solutions, and design engineering safeguards to prevent reoccurrences. Simply stated, the primary steps in the forensics of underground roof fall techniques are: ? Assess regional and local conditions prior to the event. ? Assess post-event conditions. ? Hypothesize plausible ways in which the pre-event conditions ? became the post-event conditions.Search for evidence that either denies or supports the various ? hypotheses.Apply engineering skill to relate the various facts and evidence into a cohesive scenario of how the event may have occurred. This paper details the proposed technique by utilizing a roof fall case study that required the examination of five primary factors: mine design parameters, excavation geology, method of excavation, method of support, and mining cycle times.

Jan 1, 2009

In this paper a numerical formulation is presented for determination of the axial load along a cable bolt for a prescribed distribution of rock mass displacement. Results using the program CABLE indicate that during excavation, the load distribution that develops along an untensioned fully grouted cable bolt depends on three main factors: (i) the properties of the cable itself, (ii) the shear force that develops due to bond at the cable-grout interface (i.e. bond stiffness), and (iii) the distribution of rock mass displacement along the cable bolt length. In general, the effect of low modulus rock and mining induced stress decreases in reducing bond strength as determined from short embedment length tests, is reflected in the development of axial loads significantly less than the ultimate tensile capacity even for long cable bolts. However, the load distribution is also dependent on the deformation distribution in the reinforced rock mass. Higher cable bolt loads will be developed for a rock mass that behaves as a discontinuum with deformation concentrated on a few fractures, than for one which behaves as a continuum, either due to a total lack of fractures or a very high fracture density. This result suggests that the stiffness of a fully grouted cable bolt is not simply a characteristic of the bolt and grout used, but also of the deformation behavior of the ground. In other words, the same combination of bolt and grout will be stiffer if the rock behaves as a discontinuum than if it behaves as a continuum. This paper also explains the laboratory test programme used to determine the constitutive behavior of the Garford bulb and Nutcase cables bolts. Details of the test setup as well as the obtained results are summarized and discussed.

Jan 1, 1996

By C. Dinis da Cama

In order to reduce the complexity of mechanisms influencing rock- fragmentation by blasting a simulation approach is proposed, using the capabilities of micro-computer interactive graphics. Situations involving cratering and bench blasting are simulated, and both jointed and intact rocks can be subjected to explosive action, taking into consideration its breakage mechanisms. Size analysis curves relating rock distribution before and after the blasts are determined and compared with field data.

Jan 1, 1984

By Khaled Morsy

Cementitious seals are made of foamed cements with strength ranging from 100 to 600 psi. These cementitious seals are usually used at locations where the seal will be subjected to some convergence, assuming that this material can absorb entry closure without compromising the structural integrity of the seal. Prior to 2006, Lake Lynn Experimental Mine (LLEM) conducted full-scale tests on various cementitious seals designed to meet or exceed the 20-psi horizontal static load requirements of the old 30 CFR1 75.335. Both hydrostatic and dynamic loading tests were conducted. The structural response (pressure and displacement readings) obtained from these tests were recorded. The stability of the cementitious seal is based on balancing the load applied to the face of the seal from the explosion against the shearing resistance at the seal/rock interface. Therefore, the properties of the seal/rock interface, such as stiffness, cohesion, friction, etc. are critical to determine the stability of a cementitious seal. These properties are usually assumed by the researchers in their models. This paper emphasizes the importance of having the correct properties of seal/rock interface in the numerical modeling. FLAC 3D models were developed to simulate Celuseal2 cementitious seals subjected to both hydrostatic and dynamic loadings. Using the hydrostatic and dynamic loading test data conducted at LLEM, the static and dynamic properties of the seal/rock interface were back calculated. The FLAC 3D models showed good agreement with the test results.

Jan 1, 2009

By Rafal Misa

In order to prevent the formation of mining damage or to reduce its reach, it is advisable to look for technical solutions which would enable effective protection of construction sites from the impacts of underground mining. So far, other authors have mainly focused on developing methods of securing construction sites in order to minimize the damage resulting from underground mining; the issue of geotechnical methods for protecting buildings against mining damage has not been thoroughly covered in those articles. It should be noted that there are relatively few publications directly related to this issue, nor are there practical examples of geotechnical protection. In this paper, a geotechnical solution available for securing building structures is discussed. Trenches presented in this research reduce the size and range of mining deformation. The results of numerical modelling for sample protective solutions, aimed at reducing the impact of mining activity on the terrain surface under various conditions, are presented. The calculations were performed with the aid of the Abaqus 6.10-2 software, based on the Finite Element Method.

Jan 1, 2014

By Michael Bayerl

The HILTI OneStep rockbolt was implemented for roadway development in German deep coal mines in 2004. The development by HILTI Company is based on a technical joint venture with RAG Deutsche Steinkohle AG. The technical development of a One-Step bolting system was required for weak strata conditions at the roadway development face. Standard resin bolting has reached the limit of performance when boreholes are squeezed and cannot be filled with capsules. In some cases the heading face is brittle and requires additional support for installation of the bolts and a person working immediately next to the borehole. The Hilti One-Step system allows automated and safe processing at the heading front and provides the key technique to avoid these problems.

Jan 1, 2009

By M. M. Zarnan

This paper presents the results of s study involving characterization of ground subsidence of abandoned lead-zinc mines in northeastern Oklahoma. Two coordinated efforts were undertaken: (1) collection and analysis of available data such as driller's logs, geologic cross-sections, structure contour naps and stratigraphic sections, and (2) development of a numerical (finite element) technique for prediction of collapse and mine subsidence. An in-depth analysis of a major collapse in the region was conducted. The factors which contributed to this collapse were identified.

Jan 1, 1989

By John Rusnak

The Coal Mine Roof Rating (CMRR) is a practical rock mass classification system for use in design of mine openings. Data can be obtained for this purpose from exploration drill cores if simple geotechnical logging and rock mechanics testing is conducted. The CMRR is an excellent method to quantify rock characteristics for engineering purposes. It bridges the gap between geologic description and engineering design. The CMRR was utilized in the design of a 10,000 fl. long coal belt conveyor tunnel connecting an Eastern Associated Coal Corp. mine and preparation plant in Boone County, West Virginia. Data gathering and analysis techniques are discussed involving the calculation of the CMRR and its application in the design of the tunnel, which was driven through a thin coal bed zone. The preliminary findings have correlated well with actual roof and mining conditions encountered during driving the tunnel and it is concluded the CMRR is an effective method to utilize geologic data from exploration core holes for engineering analysis and design.

Jan 1, 1998

By Gary B. Petersen

The author has developed a seven-step process called the Applied Rock Mechanics (ARM) Protocol that the author has used to solve numerous roof stability problems in mines throughout North America since 1975. It is a practical evaluation process using trained observation, innovative data collection instrumentation, video borehole cameras, analytical processes, and controlled testing methods that have become highly effective in solving ground control problems in every type of underground mine. This paper will describe each of the steps of the protocol and how the rock mechanics engineer applies them to resolve a typical ground control problem.

Jan 1, 2012

By Richard E. Bischke

Computer assisted finite element model analysis, originally developed to study stress distributions in aircraft, has been modified into a versatile mining program, that can be used to assist the engineer with predictions of mine subsidence. International Exploration, Inc. has developed an in-house finite element model program which incorporates a multitude of factors influencing mine subsidence such as mine design, physical rock properties, structure, faults, joints and topography. Finite element analysis of a mine model can mathematically determine the magnitude and direction of the principal stresses within each of the elements forming the model. By comparing the calculated in-situ stresses to the actual rock strengths, high risk regions within a mine can be identified. These potentially unstable regions of the mine can be allowed to fail within the model and the resultant stress redistribution and element movement calculated. Thus, the effects of the mine collapse at the surface can be predicted for the purpose of determining the potential damage, if any, that could occur to surface structures from deep mine failure. Stabilization materials can also be mathematically inserted into the model to design and analyze the effectiveness of subsidence prevention programs. Two examples are presented of the finite element program being used to predict mine subsidence at substantially different geologic and mining provinces in Pennsylvania.

Jan 1, 1984

By Erdal Ünal

The computer program introduced in this paper is based on design guidelines developed for selection of support systems used in mine roadways. The support types considered include rock bolts as well as rigid and yieldable steel arches. Using the computer program, the design engineer can select the type, pattern and specifications of the support systems suitable for various roof conditions. The concepts utilized, assumptions made, support selection criteria and description of the computer program, developed for the PC, are included.

Jan 1, 1989

By Clyde DeRossett

Surface fractures, sometimes of significant size, are observed in eastern Kentucky over high extraction areas. Field observations were correlated with mine maps and a regional subsidence prediction computer model. The opening of large fractures is attributed to the presence of a pre-mining joint system, which exists near outcrop in the eroded Appalachian plateau. Lithological composition of the overburden influences the process of fracture opening. No correlation was found between the areas of the predicted maximum horizontal extensions and the actual location of fractures. In this paper a mechanism of fracture formation as a result of the high extraction mining is presented, with recommendations for mine planning to minimize surface damage.

Jan 1, 1993

By Robert G. Harris

During the last five years there have been significant improvements in face support monitoring techniques particularly in respect of face pressure. The measurement of support loading pressures was originally conceived as a maintenance aid for the hydraulic systems but recent work has also included geological loading displays of the complete face as well as individual supports. This paper briefly examines the means of obtaining this information, together with some examples of actual face data. Also included is a summary of the benefits of such monitoring and an outline of future development work.

Jan 1, 1993

By Holger Witthaus

Beside the traditional geomechanical evaluation methods the geotechnical parameters are recognized as important facts of the planning work for multiple seam mining. Standards for applied monitoring and investigation methods for geotechnical determination of drill cores, laboratory rock-tests and observation of roadheadings are the basics for rock mechanics classification and support design. The geomechanical classification is in this context an essential element. The planning procedure, as it is becoming more and more detailed, beginning with the panel layout up to the technical instructions of roadway development and design of roadheading machinery, nowadays uses a lot of geotechnical information that also are expanding to include quantitative determination of more parameters. The current monitoring system includes the description of separation planes using drill cores and roadheading observation as well as laboratory tests of rock-strength and geophysical borehole examinations. This information is analyzed within the geomechanical standard-classification. The re-engineering process of comparison the predicted support success to the actual monitoring results provides the opportunity for continuous optimization of the planning work und support design. This way of empirical analysis is used for basic planning work in Germany for decades. But using the technical standard of information technology and a centralized database now it is possible to reach quick-win effects in implementing research results on the one hand and actual experiences on the other hand.

Jan 1, 2006