Search Documents

By Tom Wynne

In order to shorten the time required and improve safety for a longwall face move, a 36-ft wide longwall recovery room was predriven. The room was supported with specialty bolts, trusses and concrete cribs. Rock mechanics instrumentation was implemented to evaluate the adequacy of the whole recovery system. This included instrumented roof bolts, entry convergence, load cells, and abutment stress in the surrounding pillars. This paper describes the methodology of support and instrumentation designs, and monitoring and evaluations. The results indicated that this method offers the safest and yet faster longwall recovery so far. But the rock mechanics monitoring also indicated some improvements are desirable in the truss system and concrete crib layout.

Jan 1, 1993

By Quanzhong Gu

Stability of a pre-exnacted recovery room plays a vital role when longwall face approaches and during a longwall face move. In an attempt to extend the application of pumpable cribs into recovery room support and to limit roof bolt installation when a longwall face approaches the recovery room, yieldable and cuttable pumpable cribs (YCPC) were employed in the recovery room at the northern West Virginia mine. The YCPC consists of two layers of materials with different strengths. This allows considerable deformation from the floor and/or roof by sacrificing the soft layer while maintaining relatively high load capacity under mining¬induced front abutment loads. The thickness and stiffness of the soft layer, installation and quality control are the key factors when using the Yieldable and Cuttable Pumpable Crib to stabilize longwall recovery room- Underground observation and monitoring results show that the Yieldable and Cuttable Pumpable Crib is a viable solution to insure stability of the recovery room and can save at least two days for a longwall face move at the mine.

Jan 1, 2004

By Dan Payne

Roof falls and other ground control incidents make up a significant portion of fatal accidents in underground mines. BHP Billiton has undergone a review of all fatalities in their operations and divided these into 10 fundamental categories of which underground ground control is one. Each underground roof fall fatality was investigated and the root causes workshopped to develop a protocol for the control of fatalities due to falls of ground. This protocol sets out 22 requirements which each BHP Billiton underground mine site must comply with. This paper describes the development, requirements and application of the protocol within BHP Billiton.

Jan 1, 2006

By Hideki Shimada

In underground coal mines, grouting method is employed in order to reinforce the floor and to control the movement of groundwater into the roadway. However, the seepage and the reinforcement behavior of the grouting material into the floor are not clearly understood. Therefore, grouting is today normally based on empirical relationships and on the experience of the grouting personnel. To assist grouting projects, it must be acknowledged that many of the flow and the hardening processes occurring during grouting so far defy mathematically analysis. From this point of view. this paper discusses the behavior of grouting material, when it is injected into the roadway floor, by means of 3-D Eulerian-Lagragian seepage analysis. Moreover, the effectiveness of reinforcement grouting on the mechanical properties of slaking-prone mine tunnel floor are studied by means of several laboratory tests. Keywords: Mine tunnel floor, Grout, Seepage, Reinforcement

Jan 1, 2002

By Rossen A. Halatchev

This study introduces a new probabilistic approach to seismic stability analysis of embankments and slopes. The approach is based on Sarma's solution, which is modified through presentation of the seismic force by its horizontal and vertical components; i.e. the force may have an arbitrary inclination. The probabilistic modelling includes Monte Carlo simulation of the shear strength parameters of the soil mass, which are assumed to have a normal distribution. The probability of failure is determined based on the seismic co-efficient, which is treated as a random quantity. The probabilistic approach is illustrated through a solution of a numerical example from an opencast coal mine.

Jan 1, 1992

By Kanaan Hanna

The integrity factor approach was developed by the Bureau of nines to assess the stability of mine pillars and has been applied primarily to longwall chain pillars. Recently this approach was applied to a room-and-pillar mine in the Illinois Coal Basin. A special configuration of hydraulic borehole pressure cells was installed in a pillar to determine the in situ strength-and- stress relationship of the coal pillar and to verify the applicability of the integrity factor approach. Results indicate that the integrity factor approach is applicable to the assessment of pillar st6b:lity and nay bs a realistic and effective approach for room-and-pillar mine design.

Jan 1, 1988

By E. Bauer

During 1987 and 1988, the Eighty Four Complex Mine of BethEnergy Mines, Inc. used the open entry longwall recovery method to recover one partial and three complete longwall faces. Various cement- concrete supports were utilized to support the open recovery entry until the approaching longwall face cut into this entry. This recovery method and the supports used were studied by the mine personnel and the Bureau of Mines. This paper discusses the findings, results and conclusions of that study.

Jan 1, 1988

By G. C. Xiao

A database, incorporating historical data from British mines, to study the factors affecting inflows from proximate aquifers into longwall workings, showed that a main casual factor was the immediate roof strata lithology. When this comprised principally stronger sandstone, there was a tendency for periodic inrushes associated with face weighting. This phenomenon is explained by the collection of water in bed sepa¬ration cavities, where free water connected to a high pressure head aquifer source, may be trapped.

Jan 1, 1990

By George J. Karabin

Since the inception of a qualitative pressure arch theory by Haak4 in 1911, much work has been done in an effort to apply this concept to underground mining. It has been used in both longwall and room and pillar mining to determine roadway and pillar stability (with varying degrees of success). This paper presents a summary of a case study where the pressure arch concept was extended in a totally qualitative manner to define the source of roof control problems in the mains of a Pennsylvania mine. It was concluded that, due to the method of mining employed, a pressure arch formed over a portion of the entries, and the high abutment stresses accompanying it resulted in extreme roof deterioration. The following discussion will include a general presentation of the arching mechanism, the physical response of the roof strata under mining-induced abutment stresses (both from the case study and in general), a computer simulation of ground stability under both "normal" and "abutment" stress conditions, and finally, potential means of alleviating such conditions.

Jan 1, 1982

By S. N. Zhow

China has at least 200 collieries suffering from the problem of instantaneous outbursts of coal and gas. The strong outbursts often occurred in active tectonic lanes and areas of high stress concentration. In this paper, the author describes some characteristics of the strong outbursts and analyses the effects of ground stress, gas pressure and the properties of coal in outbursts.

Jan 1, 1987

Retreat longwall method with re-use of gateroad has been traditionally employed in Japan, mainly because of the advantage of higher recovery. But the Miike Colliery has newly introduced the interpanel-pillar system to maximize the production efficiency. The Department of Mining, Kyushu University, in cooperation with the Miike Colliery and the Coal Mining Research Center (CMRC), has conducted research into the optimum design of interpanel-pillar, because this system may be adopted in other coal mines as well. Field measurements of the deformation of the gateroads and of stress distribution in the pillar show that the designed layout of the panel and pillar and the supporting system are proper from the viewpoints of gateroad maintenance and spontaneous combustion in the pillar.

Jan 1, 1990

By Yunqing Zhang

Weak shales refer to those with lower strength, thinly- laminated structure, sensitivity to moisture and weathering as well as significant time dependent behavior. It has been said that many future coal reserves with good quality have weak immediate roofs. Therefore their geo-mechanical properties and behavior must be known before an appropriate support plan can be designed. In this study, four types of shales collected from underground coal mines were tested in the laboratory. Their modes of failures in underground were observed and correlated with their lab behavior. The failure mechanisms of thinly-laminated weak shales were analyzed by the means of numerical modeling.

Jan 1, 2004

By Susan Robertson

Many injuries are caused each year by rock falls in coal mines. Most of these injuries are not caused by major roof collapses, but from falls of smaller rocks from the immediate top or roof skin. Various surface controls are used in mines to control this surface rock. One that has been found to be very effective is roof screening. Depending on the size of the screen, roof coverage approaching 100% can be achieved. Many mines are reluctant to use screen for primary skin control because of additional costs of time and materials, but others are having great success at both controlling costs and surface rock. Data is presented from two mines that show a dramatic reduction in roof skin injuries when screening is used. Much of this success is due to innovations in roof bolting machines. Four case studies of roof screen experience are presented along with associated costs of materials, impact on bolting advance rates, and potential ergonomic risks. The effects of roof screening on skin control and safety are also included. Finally, this paper will provide information about features of different roof bolting machines that affect production and safety.

Jan 1, 2002

By Andre Vervoort

The roof in coal room and pillar panels is normally stratified and can be thought of as beams or plates supported by the pillar sides in the roadways and by pillar corners in the intersections Underground measurements showed the effect of the face advance on the additional total movement of the roof skin and on the relative movement between various layers in the roof. The latter consists of the opening of bedding planes and of the lateral sliding of layers over one another. Both phenomena increase locally the axial load along full column anchors. Four models have been used to come to a better understanding of the roof behavior: a beam either clamped above the pillar side or laying on the pillar sides and a three-dimensional boundary clement model with and without bedding planes. The shape ref the curvature of the roof deflection is host approached by a clamped beam: the other models overestimate the movement at the sides. The largest roof deflection for a given Young's modulus is estimated by the model incorporating bedding planes. This model estimates that the bed separation occurs close to the face (within the first meter) and within 0.2 m of the sidewalk. In some simulations, openings are even recorded just ahead of the face. Further underground measurements should focus on these findings, as the effectiveness of the support is directly related to the amount of bed separation and sliding, which have occurred prior to the support installation and which still cart occur abler installation.

Jan 1, 2000

This paper presents a two-dimensional numerical procedure which incorporates concepts related to the mechanics of strata deformation' as well as' empirical indices associated with subsidence engineering. Regional deformation data were employed in order to establish overburden deformation zones, while material properties were kept constant. Scaling of final displacements was based on empirically predicted values for subsidence and strain for the Appalachian coalfield. The model was validated with a number of regional case studies and predicted subsidence and strain curves were compared to those obtained using the semi-empirical influence function formulation developed by VPI&SU.

Jan 1, 1988

By Erik C. Westman

The objective of this Bureau of Mines study is to determine the structural integrity and stress state of coal structure using seismic techniques. Bureau personnel conducted seismic transmission and refraction surveys on yield pillars and seismic tomography on rigid pillars. The pillars studied were in the headgate at increasing distances from the working face of a longwall coal mine, effectively evaluating pillars at lowering stress states and increasing levels of structural integrity. By examining characteristics of the seismic wave, including velocity and frequency, the survey results are used to infer yield zone thickness, core mss state, and stress distribution. An accurate definition of these parameters can not only provide mine engineers a useful tool for evaluating mine design, but also give valuable insight into the inherent safety of the mine structure.

Jan 1, 1993

By Tom Vandergritft

With advances in system design driving higher productivity, safety, and coal recovery, highwall mining is becoming an attractive option for extending reserve life at surface mines. Typically, highwall mining is performed by contract, with the system owner charging the mining company on a per ton basis, plus a mobilization fee. For this arrangement to benefit both parties, geotechnical planning is required to minimize risk to highwall mining personnel and equipment, while maximizing coal recovery. This paper discusses how highwall mining has been successfully implemented at a large surface coal mine in Colorado, including design procedures, operational factors, and productivity. The operation includes an area where four seams are mined in succession from the lowermost upward, requiring careful attention to seam interaction issues.

Jan 1, 2005

By Timothy Ross

The Pittsburg & Midway Coal Mining Co.'s Kemmerer Mine is one of the deepest surface coal operations in the world, with the highwall extending to approximately 1,000 ft above the pit floor. To increase recovery, auger mining is being evaluated beneath the highwalls of several seams representing the current economic limit of pit development. The primary augered seam is over 50 ft thick, can approach 100 ft thick, and dips into the highwall at an average of 17 degrees. The seam thickness and dip present many geotechnical design and operational challenges for multiple Sup to five) lift augering. This paper presents the design criteria and methodology applied to determine appropriate web and septum thicknesses for the various cover depths anticipated, as well as operational measures that can be taken to increase overall coal recovery. The primary tool used in the design was the finite difference code FLAG. Models incorporating typical strata sequences associated with the coal seam were run at several different cover depths corresponding to the maximum anticipated auger penetration. Web and septum thicknesses were varied until the minimum thickness satisfying a given safety factor criterion was determined. Using this procedure, design curves were developed for web and septum thickness versus cover depth. Operationally, several recommendations were developed to ensure that overall coal recovery is maximized. By angering across the scam dip, auger penetration per hole can he increased dramatically, and by carefully planning maximum planned auger penetration versus hole spacing, increased coal recovery can be safely attained.

Jan 1, 1999

By S. S. Peng

The hydraulic powered supports have been employed in U. S. longwall mining for the past two decades. Yet the sciences of roof control at the powered supported faces remain largely unknown. In order to improve longwall roof control and increase production, a series of questions in longwall roof control should be studied and answered: what is the basic rules of roof behavior in longwall coal faces equipped with the hydraulic powered supports? What is the interaction between the roof, supports, and the floor What is the contact condition of the canopy with the roof, and consequently the load distribution on the canopy? Des the periodic roof weighting really exist in the powered supported face and if so, how does it affect the face area? This paper presents the preliminary analysis of underground observations and instrumentations in a longwall panel with 4-leg shield supports designed to address the questions mentioned above.

Jan 1, 1982

By Sun Henghu

This paper analyses problems associated with cement based technique in metal mines, and provides a new mining technique of packing the tailing sand and water into solidified material. In the new technique, the cementing agent is a solidifying material containing a high percentage of water and tailing sand. The sand and water solidify into the packed body at the same time. The slurry of the packed body varies widely in concentration and suitability for different mining conditions. It consists of two liquid materials, each composed of a cementing agent, tailing sand and water. The thick liquids are transported to the packing place at the same time. Their pumping property is good; they do not solidify or block up the pipe during transportation. At the packing place, the two liquids are evenly mixed. The mixed liquid flattens out well and its solidifying speed is so fast that it solidifies into a packed body within a very short period of time. The compressed strength of the packed body can reach 1.2-5MPa in one day, which satisfies the requirements of different mining conditions. By using the new mining technique, all the tailing sand can be used again in the packed body and it is low in cost and investment. The mechanisation is easy and thus the working efficiency is increased and the use of labour decreased. Contamination problems caused by excess water drainage under the ground are resolved.

Jan 1, 1992