Search Documents

By Eric Westman

Ground control problems caused by multiple-seam interaction frequently sterilize coal reserves. Interaction mechanisms differ for overmining and undermining and are controlled by mining, spatial. and geologic conditions at each site. A multiple-seam interaction analysis software program, UGLY (Uppersearn Gateroad Longwall Stability), has been used to evaluate sterilization of coal reserves due to overmining at three locations. Four case histories were reviewed to determine the effectiveness of improved ground control in mitigating interaction effects.

Jan 1, 1997

By Jan A. Nemcik

Steel mesh has been used successfully for many years to control friable roof conditions and prevent loose roof and rib material from caving into the roadway. Despite its extensive use, the installation of steel mesh is difficult to automate and many other products have been evaluated as an alternative for skin control. Ideally, the properties of these new products should be similar or better than those of the steel mesh. In particular, development of a strong and resistant shell that minimizes movement along the fractured rock and coal surfaces between the bolt anchors is recommended. A strong surface adhesion and the strength of a reinforced polymer skin can provide the necessary toughening mechanism required to enhance roadway surface support by forming a reinforced polymer/rock surface layer. Most of the Thin Spray-on Liners (TSL) evaluated in the mines are weak with slow curing times, and the plastic mesh currently used to support the coal ribs is relatively weak. Therefore, neither material can seriously compete with steel mesh. Currently, a new polymer product that cures in seconds and forms an instantaneous strata binder that surpasses the properties of steel mesh is under development at the University of Wollongong.

Jan 1, 2009

By Raymond M. Stateham

The Bureau of Mines has developed a portable, lightweight device for determining the integrity of resin-grouted roof bolts. The instrument functions by sending a known pulse of ulstrasonic energy into the bolt and comparing the amount of energy reflected hack with the original measured pulse. Where the bolt is properly bonded or coupled with the rock, the energy passes through the bolt-resin-rock interface and dissipates in the rock. Where the bolt is not properly coupled, the energy is reflected back along the bolt to the instrument. The ratio of reflected energy to the pulse approximates the fraction of the bolt's surface that is improperly bonded. The instrument is easy to use. The operator holds the sensor head of the device firmly over the head of the bolt to be tested, causing the pulse of ultrasonic energy to be imparted to the bolt. The device then listens for reflected energy. This cycle is repeated about 200 times per second until an evaluation of the bolt installation is made and indicated by colored lights in the display window. Bolts having 50% or less of their surface bonded are considered had and cause a red light to he illuminated. Bolts with 50% to 75% of their surface bonded cause a yellow light to be lit and are considered marginal. Bolts having more than 75% of their surface bonded are considered good and cause a green light to be lit. The indicator lamp remains on for about 4 seconds and then goes off, indicating that the instrument is ready for another test.

Jan 1, 1982

By Mark K. Larson

Researchers at the National Institute for Occupational Safety and Health?s (NIOSH) Spokane Research Laboratory are developing a borehole profilometer to dynamically measure the roughness pro-file of boreholes used to install roof bolts fully encapsulated with resin. Numerical measures of roughness were calculated from profiles of borehole surface roughness to determine potential roof bolt anchorage capacity. The concept of dynamically profiling was proven through the following series of laboratory tests: a sensitiv-ity test using various grits of sandpaper, a known-profile test along a section of a concrete hole, and a simulated borehole test in a pipe with machined grooves. Two profilometer prototypes were devel-oped that measure slight changes in the radius of a borehole using either strain-gauged, spring-steel arms or rigid, steel arms attached to a spring-loaded cone and a linear potentiometer. Both instruments performed reasonably well in the laboratory and were subsequently tested in boreholes drilled in two concrete blocks using different drilling techniques to obtain three different borehole surface roughnesses. A Z2 roughness parameter was calculated with data from the first profilometer, and an average radial increment was calculated from the test results of the second profilometer. Although both instruments were able to readily distinguish the difference between smooth and rough boreholes, the correlation coefficient (r2) for a linear relationship between Z2 and average radial increment was 0.577. Pull tests were conducted with resin bolts installed in the concrete blocks, but maximum pull-out strength could not be correlated to borehole roughness because in each of these tests, failure occurred at the resin-bolt interface. A more sophisticated prototype has been designed to measure surface roughness and also accurately determine the location and tilt of the instrument in the borehole. However, this instrument has not yet been fabricated or tested.

Jan 1, 2007

By Lorraine Kent

Mine tunnel support using rockbolts was introduced in UK coal mines over the period 1987- 1992 and is now used in over 70% of all mine tunnels. In every case the reinforcement design has been based on the observational approach. After the initial reinforcement design has been established appropriate action levels are defined for predetermined amounts of movement indicating the onset of instability. If the action levels are exceeded appropriate remedial action is taken usually in the form of additional support or reinforcement to maintain stability. This paper outlines the observational design method as used in UK coal mine tunnels. It discusses the low cost instrumentation which has been developed to monitor roof deformation, dual height telltales, how action levels are defined based on the geotechnical environment and the types of remedial measures typically taken. An alternative approach for dealing with areas of increased deformation involves reacting to early roof movement trends and modifying the support installed at the face of the development accordingly. Installation of additional support at the face of the heading improves ground control in poor geotechnical conditions and has the advantage of potentially reducing later additional support costs. A case study is described to illustrate how 'early' action levels can be incorporated into a roof support plan enabling a flexible roof support strategy. Such a system will be site specific and continued analysis of monitored information will be required to confirm the action levels or to adjust them according to any change in geotechnical environment. More accurate roof deformation monitoring systems, such as the Remote Reading Telltale system recently developed by Rock Mechanics Technology Ltd. (RMT) and currently undergoing Mines Safety and Health Administration (MSHA) approval, are ideally suited to this application. The Remote Reading Telltale system provides accurate mine wide monitoring of roof condition on a surface PC.

Jan 1, 1999

By Xiangxi Wu

Longwall and continuous mining are prevalent methods employed by Chinese underground coal operations. The main ground control challenges include roof skin deformation, roof collapse, and outbursts of coal, gas, and water. Microseismic monitoring provides valuable information on rockmass behavior and fracture propagation caused by stress redistribution, active geological structures, or gas build up within the coal strata and the surrounding rockmass. Collecting and assessing seismic data has proven to be an instructive tool for engineers to better assess ground conditions and mitigate seismic hazards associated with mining. The development of intrinsically safe and explosion proof certified seismic monitoring equipment has revolutionized China?s underground coal mines. The use of this technology allows for the optimization of gas drainage at an increased rate of two at a 50% higher purity without any increase in drilling costs. Microseismic monitoring can also be used in identifying seismically active faults and shear zones. This information can be used to assess and revise mining strategies to improve safety and ground stability.

Jan 1, 2012

The purpose and current practice of cable trusses in underground coal mines is briefly outlined and details of various cable truss designs are presented. The main part of the paper describes the in-situ performance of cable trusses installed as secondary supports in gateroads and recovery roads of longwall coalfaces. The performance analysis is based on the results of in-situ monitoring carried out at a number of sites at two underground coal mines within Australia. Truss performance has been assessed as load developed in relation to roof convergence, face position and time. Additionally, the influence of strata conditions, installation pattern/density, roadway layout and geometry have been taken into account. An analytical model has been developed to predict truss loads. The principal variables are listed and the basis of the model is described. Based upon behaviour observed in the field the model has been progressively upgraded and validated against measured performance. Guidelines on truss performance and factors which influence it are presented and the implications of these to the use of cable trusses is discussed. Possible methods for improving truss performance in certain strata conditions are outlined and some comments are made on the value of cable trussing compared to cable bolting in these situations,

Jan 1, 1992

By Edward A. Barrett

A significant number of injuries resulting from fa118 of roof and rib may be avoided by modifying the reactive behavior of miners as they encounter potentially hazardous ground conditions. In 1984-85, the Bureau investigated barriers which prevent miners from recognizing and correcting groundfall hazards. One basic problem from which these barriers originate is the inability of miners to recognize dangerous roof and rib conditions. This study is a report of experimental research on the use of stereo scopic (3-D slides for presenting visual cues associated with hazardous roof and rib conditions. Findings reveal that, in comparison to conventional slides, 3-D provides for significantly greater hazard recognition among both experienced and inexperienced miners. Details such as the presence of t cracks and gaps in the surrounding rock are more accurately and realistically perceived. Acceptance by the mine training community has been affirmative and is additionally encouraged by the fact that 3-D slides stimulate trainees' overall interest.

Jan 1, 1986

By Michael Alber

Resin grouted rock bolts are the major support measure in coal mining. They are rather easy and foolproof to install, take immediately load and are the least time consuming support measure for controlling gateroad deformation. The use of only resin grouted bolts allows fast gateroad development which is essential for economical resource exploitation. The design of reinforcement / support systems for coal mining typically bases on empirical methods, which work fine when encountering known or usual ground conditions. However, coal mining approaches depths where little experience exists and numerical modeling is often the only method to estimate ground behavior. This paper discusses the geotechnical properties relevant to numerical model and focuses particularly on input values for modeling resin grouted rock bolts for safe gate design.

Jan 1, 2006

By Zhang Liandong

Roof control in thick-seam mining has long been a difficult problem in mine design and coal mining. In the early 1980's, through ground control instrumentation and investigation the rules of roof strata movement were determined, based on which the sliding roof bar powered support was properly designed and successfully applied to roof control to thick seam mining with caving. Underground trials in Huating Coal Mine produced satisfying results. The technique is being employed in many Chinese coal mines and won the national price for technical advance.

Jan 1, 1990

By Robert R. Thompson

Retreat pillar mining is highly productive but dangerous. The primary danger during pillar removal is premature caving of the roof. Because the safety of the miners is dependent on successfully controlling the roof, the roof must cave in a predictable and dependable manner. Temporary support during retreat is usually obtained by setting posts. They are set manually by a miner working in a dangerous area. A solution to this problem would be a system which could set and retrieve roof supports remotely and safely. The Bureau of nines has developed a remotely operated Mobile Roof Support (PIPS) machine which will place and retrieve temporary roof support. Two PIPS machines were fabricated under a cost-sharing agreement with Southern Utah Fuel Company and mining equipment manufacturer. Each machine carries four 50-ton jacks and is remotely- Controlled by radio. The machines are presently being used by Southern Utah Fuel Company under a long-team cooperative agreement. Not only have there been material and manpower cost savings in not having to set posts, but also the time saved bas resulted in increased productivity. The projected costs of mass-produced machines with tethered remote control rather than radio remote control are estimated at $150,000 each. The radio remote control is more expensive and is considered an optional extra.

Jan 1, 1986

By Jun Han

Coal has been mined in the Kailuan mining area for more than 130 years. The remaining reserves consist of, in large part, coals that would have been considered economically unminable or technically not feasible by the previous generations. Some of the current operations have to resort to overmining because the lower seams had been extracted in the past. This paper deals with the feasibility and proper layout of mining roadways of overmining carried out in the No. 5 seam of Qianjiaying coal mine of Kailuan mining area using numerical and physical simulation. FLAC2D was used to investigate the characteristics of stress and displacement in the overburden after extraction of the lower seams. It also analyzed the proper layouts of gateroads in the upper seams, i.e. locating them in the stress-relief zone of the gob so that their stability can be easily maintained. In addition, a two-dimensional physical model was constructed for investigation of damages to the upper seams due to mining of the lower seams. Finally, based on the results of investigations, proper gateroads layout was designed and successful extraction was implemented for panel 1357 in the No.5 seam.

Jan 1, 2009

By Wojciech Masny, Andrzej Walentek

"The most common extraction method in Polish coal mines utilize pillars between adjacent longwall panels. This is mainly due to the significant depth and difficulties in maintaining stability of the gateroads. This paper presents measurements of entry convergence and range of the fracture zone around a gateroad measured with a borehole camera. The entry where the measurements were taken was located in a parallel entry separated from the gateroad by a 5-m- (16-ft-) wide pillar. The gateroad was located in a hard coal seam 900 m (2,952 ft) deep with a dip of 5°. The extraction method was longwall mining with caving and the mining height was about 3 m (10 ft).Furthermore, the ""in situ"" measurements were compared to the convergence forecast for the gateroad and fracture zone by means of numerical modeling conducted using the Phase2 Version X.X finite element program from Rocscience. The determination of the fractured zone around the openings is of great importance to successful mining practice, especially in support planning and design for longwall gateroads. Moreover, proper determination of the fractured rock zone is one of the basic elements in the process of planning the roof bolting for mine workings.INTRODUCTIONIn the Polish. hard coal mining sector, retreat longwall extraction is most commonly used (Prusek and Masny, 2007). This method is connected with the necessity to carry out a number of development operations during the first stage, including among others, driving of gateroads and a setup room.Currently, most Polish mines eliminate gateroads behind the extraction front, using the ""U"" ventilation system (Szlitzak et al., 2008). In such cases, one of the roads for the next longwall panel is driven along the caving goafs, leaving a protective pillar of some chosen width (Figure 1). The question regarding the width of the coal pillar is especially important to the stability of the gateroads that define the panel for the subsequent longwall. When analyzing the previous experience relating to this type of pillar (Junker, 2006; Rajwa, 2008; Stranzet et al., 1973; Betriebsempfehlung, 1982), one can state that there exist two solutions for the determination of its width."

Jan 1, 2010

By Xinchuan Xia

Based on the stepwise strain features and the strength reduction law of the surrounding rock in extremely softrock roadway, this paper proposes a dynamic supporting principle. A new kind of stepwise reinforced technology, which consists of immediate shotcreting, timely bolting and delay grouting, was optimized after thorough analysis and illustrated with a successful engineering example in extremely difficult softrock roadway.

Jan 1, 2000

By Kevin M. Connor, Malcolm J. McPhersqn

Examples are presented in which Time Domain Reflectometry (TDR) was employed to locate deformation of rock masses induced by mining. The first example involved motoring the propagation of overburden fractures above a longwall coal panel and the second example involved the we of a)R to monitor rock mass deformation in the vicinity of a strip mine highwall. Bock mass deformation, strata separation and large block movement generated strains and failure along coaxial cables which were installed in drill holes and the TDR reflections generated by these strains and failures were monitored. Analysis of field data and a preliminary laboratory test indicate that it may be possible not only to locate rock mass movements but also to quantify these movements with TDR data.

Jan 1, 1984

By Steve P. Signer

A study of rock support interaction mechanics was conducted by the U.S. Bureau of Mines at the Jim Walter Resources No. 7 Mine, Brookwood, AL. Bolt loads and entry deformation were monitored at four sites in a tailgate roadway. Two sites were areas supported by fully grouted resin bolts, and two sites were supported by tensioned bolts that used resin-assisted mechanical anchors. The yield capacity of the tensioned bolts was 37 pct higher than that of the grouted bolts. To monitor loads, instruments were mounted on 16 bolts, which were installed during entry development in the standard bolt pattern. Additional instrumented bolts were installed as supplemental support just prior to the headgate pass of the first longwall. Instruments to measure roof movements included three-point roof extensometers and convergence stations. Readings were taken during section development and as each longwall panel passed the test area. The fully grouted bolts showed localized loads that were higher than loads on the tensioned bolts; however, overall loading magnitudes were similar. Many sections of the fully grouted bolts passed the yield point of the bolt steel (98 kN or 22,000 lb). However, the maximum strain measured at any loca¬tion was 50 pct of the ultimate strain, and there was adequate bolt length to transfer the high loads into the rock. Significant bending was detected at many points along the length of the bolts and seemed to be the most significant mechanism in support-rock interaction. Loads on the tensioned bolts did not exceed the yield point of 160 kN (35,000 lb). Entry deforma¬tion, supplemental bolt loading, and general entry degradation appeared to be slightly less at the tensioned bolt sites. Local geology and in situ horizontal stress were also observed to affect con¬ditions at the test sites.

Jan 1, 1993

By Renn Oler

Corrosion can often cause significant strength reduction and failure of steel rockbolts, thus demanding continuous rehabilitation and posing challenges to underground mines in maintaining long term ground support. The mining industry has traditionally applied galvanized and epoxy coatings for protection of ground support and reinforcement in corrosive environments due to cost considerations. However, under a harsh and corrosive groundwater condition with extreme pH levels, failure of the existing coated rockbolts often results in failure and falls of the mine roof, especially in long-term mine drifts or entries. To prevent the roof falls induced by corrosive bolt failure, DSI developed a new polymer coating, called ?Obduro AP coating,? to combat harsh and corrosive ground conditions. The new polymer coating was tested in extreme conditions to identify weaknesses and was found to be capable of handling highly corrosive mine water solutions. This paper highlights the challenges faced by underground mines with corrosive bolt failure and shows that the DSI Omega BoltTM can withstand the most corrosive ground conditions when it is coated in the new, economic Obduro AP coating.

Jan 1, 2014

By Haile Manteqi

In longwall coal mines, estimation of roof strata condition, sequence of loading, and supporting requirements are of a high degree of importance, and they are directly related to production and safety. Also, a prediction of the initial caving distance is rather complicated to calculate, because there are many parameters that effect caving process?roof and floor strata conditions, thickness of immediate roof, depth of cover, excavation geometry, and magnitude, and direction of principal stresses. This paper presents the results of 3D numerical modeling of the initial caving mechanism using the finite difference code FLAC3D at the E1 longwall panel of the Parvade 1 underground mine located in the Tabas area in the central part of Iran. The initial caving distance obtained was 10.4 m. Also, the results of numerical modeling have been compared to the analytical methods, such as Peng?s method. The results show good agreement with each other.

Jan 1, 2012

By David Newman

In Eastern Kentucky, the Darby seam has had an extensive history of coal bumps and pillar bursts. The combination of high overburden, strong rock and coal, subjacent and superjacent mines, and retreat mining has produced incidences of violent pillar failure. The influence of these factors on pillar stability and the potential to bump is illustrated in two case histories. In the first case history, a bump occurred unexpectedly during the retreat mining of a five heading continuous haulage panel. Alternative cut sequences and pillar dimensions were analyzed to identify a geometry that would reduce the potential for future coal bumps or bounces during retreat mining. The viability of the alternatives was constrained by the reach of the continuous haulage system, the overburden depth, and the presence of thick sandstones in the main roof. Each alternative was numerically modeled cut-by-cut to examine the mechanism of stress transfer, as a pillar row is retreat mined. This approach highlighted which cuts were being made in highly stressed portions of a pillar and therefore more prone to coal outbursts. Validation of the numerical modeling was accomplished by comparing the cuts where bumps and outbursts had occurred underground to the highly stressed cuts shown within the models. Recommendations of the barrier pillar width between adjacent panels, pillar dimensions, and changes in the retreat mining sequence were proposed based upon the overburden thickness, geology, and the result of the numerical modeling. The second case history documents a nine-entry panel 3,600-feet long that was retreat mined a distance of 2,064-feet without a significant roof fall or roof-floor convergence. Mine management became concerned about the potential for a coal bump or a large roof collapse within the gob and the resulting air blast. The stress on the pillar line and within the remnant pillars in the gob was quantified through numerical modeling. Changes in mining practices on the current panel were implemented to avoid a bump in the active panel. A barrier was established between the current and the future panels to protect the future panel against abutment pressures from the void area. A change in pillar centers was proposed in the adjacent panel to absorb the side abutment pressure from the gob of the active panel.

Jan 1, 2008

By Keith Heasley

An eastern longwall mine was required to mine through a set of three entries located midway down the length of a panel. Of course, the mine desired to design a successful support system for the mine-through area at the least cost. To further complicate the design process, the mine-through entries were located directly under the end of a previously mined, overlying longwall panel and the entries were close enough to be subject to stress interactions from the overlying seam. In order to accurately evaluate the multiple-seam stresses and modify the mine-through support system appropriately, the boundary element program LaModel was used to model the stress and displacements in the two mines. Using the results of the model's stress analysis, the support density was systematically varied throughout the mine- through entries for optimum sup@ efficiency and economics. During the actual mining of the cross panel entries, the longwall experienced few, if any, additional delays, and overall, the support and mine through of the cross-panel en- tries at Harris #1 was very successful, saving the mine confineable time and money.

Jan 1, 2003