Search Documents

By Cao Shenggen

Experiences in the developed countries have shown that continuous increase of panel width (or face length) is one of the major technical trends for high production high efficiency mines. Increasing the panel width will increase not only the panel output, simplify the gateroad layout, facilitate high concentration of production, but also increase resources recovery and facilitate protection of surface structures. This paper uses the No.4326 super- wide panel, Wangzhuang Coal Mine as an example. This mine employs the fully-mechanized top-coal caving longwall mining method. Through surface subsidence monitoring, the dynamic characteristics of surface movement were obtained. The dynamic surface movement during mining and the final surface movement after mining were predicted using the Mining Subsidence Prediction System. The results indicate that after mining, the surface above the super-wide panel reached a state of full subsidence, So it can ensure the No.309 National Highway above is located in the flat bottom of the subsidence basin, and there is little impact on the national highways when panels on both sides of 4326 Panel are mined.

Jan 1, 2003

By Michael Alber

Coal mining by the longwall method typically causes seismic events. This paper describes the research on mining induced seismicity around two specific longwalls at 1100m depth under several old longwalls. A local network featuring 21 geophones has been installed, underground core drilling and an extensive rock testing program were executed. A rock mechanical model featuring a multi-layer strata was created for use with numerical analyses. Seismic events were localized and three different event types are described. Focal analyses yielded distinct modes of failure. Those types are explained by different failure mechanisms, namely fault activation, remnant pillar punching and beam failure. The use of rock mass classification, rock mass strength criteria and in situ stresses together with 2D and 3D numerical analyses allows evaluating the findings from seismology approaches. Conclusions are drawn that the orientation of longwall with respect to the major horizontal stress orientation plays an important role in mine induced seismicity.

Jan 1, 2008

By Herryal Anwar

The application of roof bolting technology to control the stability of roadways in coal mining within weak strata or under high ground pressure has improved progressively. One of several factors that affect the design of rock bolting is the immediate roof characteristics of the roadway. On the competent rocks, the mining conditions may indicate a high level of stability and a low density of bolting patterns may be adequate to control the ground stability. However, at a weak strata, the roadway will be affected by both horizontal and vertical stresses that may generate a high level of deformation in the immediate roof. This sensitivity of the roadway will require a mine plan design which consider the pillar sizes and sequences of extraction as well as a conservative reinforcement to maintain the integrity of the deforming weak roof strata. Rock bolting technology has been used to maintain the stability of roadways in Indonesia and Japan for a few years. In this paper the overview of the application of rock bolting reinforcement in Ombilin Coal Mine, Indonesia and Miike Coal Mine, Japan is given.

Jan 1, 1999

By Quanzhong Gu

Stability of a pre-exnacted recovery room plays a vital role when longwall face approaches and during a longwall face move. In an attempt to extend the application of pumpable cribs into recovery room support and to limit roof bolt installation when a longwall face approaches the recovery room, yieldable and cuttable pumpable cribs (YCPC) were employed in the recovery room at the northern West Virginia mine. The YCPC consists of two layers of materials with different strengths. This allows considerable deformation from the floor and/or roof by sacrificing the soft layer while maintaining relatively high load capacity under mining¬induced front abutment loads. The thickness and stiffness of the soft layer, installation and quality control are the key factors when using the Yieldable and Cuttable Pumpable Crib to stabilize longwall recovery room- Underground observation and monitoring results show that the Yieldable and Cuttable Pumpable Crib is a viable solution to insure stability of the recovery room and can save at least two days for a longwall face move at the mine.

Jan 1, 2004

By T. N. Singh

Board and pillar system of mining has beer, practised in India in view of abundant availability of cheap labour force, low investment and quick return. Subsequently, selective mining from thick seems and partial mining under surface features boosted the trend. As s result over 2000 million tonnes of coal is locked up in form of developed pillars inclusive of about 1000 million tonnes of high grade coking coal in Jharia field alone. The trend of pillar formation is still uninterrupted as the estimated pillar reserve in this field in 1974 was only 700 million tonnes which increased to 961 million tonnes in 1983. The trend is not much different in other coalfields end as a rough estimate 100 million tonnes of virgin coal reserve is being transferred to pillar every year. The method of board and pillar mining is likely to remain moat preferred technology for decade9 to come in view of several inherent advantage in Indian mining conditions.

Jan 1, 1984

By Gabriel Esterhuizen

When designing pillars in coal and hard rock mines it is necessary to determine the strength of the rock mass forming the pillars. Empirical strength equations, based on rock mass classification techniques, assume that the rock mass is isotropic, this simplification may result in under estimation of pillar strength. Numerical model studies showed that the effect of jointing on pillar strength diminishes as the width to height ratio of a pillar increases. Therefore, the weakening effect of joints should not be equally applied to all pillars regardless of their width to height ratio. The paper presents equations that were developed from laboratory tests on jointed rock samples and numerical models to account for the effects of joint orientation, friction, frequency, and pillar width to height ratio on pillar strength. The equations were calibrated using field data of actual pillar performance in South African coal mines. The method was applied in two case studies in which the strength of jointed coal pillars was assessed and layouts were designed accordingly.

Jan 1, 2000

By Yongjie Yang

Experimental study on the strength and deformation characteristics of coal under cyclic loading provides guidance for designing coal pillar which is subjected to repeated mining influence during mining. This paper studies the strength, deformation and fatigue process of No.3 coal from Xinhe Colliery under cyclic loading by the MTS815.03 servo-controlled rock mechanics test system. The results indicate that coal is more susceptible to fatigue damage than other hard rocks. Under uniaxial cyclic loading, the fatigue failure ?threshold value? of coal is smaller than 78% of its uniaxial strength, and there is also some fatigue damage when cyclic loading and unloading experiment is carried out below the fatigue failure ?threshold value?. Axial deformation can be divided into three stages: Initial deformation, steady-state deformation and accelerating deformation. Transverse deformation can be divided into two stages: Stable deformation and accelerating deformation. When the transverse deformation begins to increase rapidly and the deformation recovers only slightly upon unloading, it?s a precursor to failure of coal. Under cyclic loading, fatigue failure develops through a process of compaction, strain hardening, and strain softening.

Jan 1, 2006

By Asmaa Yassien

Finite element models were developed to study the effect of tensioned and fully-grouted bolts on the stability of the mine opening in a three-entry development system using a typical geological column for the Pittsburgh Coal Seam. The models were used to study the effect of each bolt type on the stress distribution in the immediate roof, yield zone development and the vertical deformations. Comparison of all of those features show that the effect of a tensioned bolt on the stress distribution in the immediate roof is restricted to limited areas, whereas the fully-grouted bolt has a much wider effect on the stress distribution. Both types of bolts can reduce the yielding and deformation in the immediate roof to different degrees. The fully-grouted bolt reduces the sliding along the bedding plane more than the tensioned bolt. Both types of bolts were able to maintain the bedding planes without separation. The induced forces in both types of bolts are analyzed. A rapid increase in the shear force and bending moment occurred in the fully¬grouted bolt due to the relative motion of bedding planes.

Jan 1, 2002

By Matthew J. DeMarco

Research personnel at the U.S. Bureau of Mines have conducted longwall gate stability studies at four western U.S. mines attempting to employ yield pillars for improved ground conditions. Located in the Book Cliffs and Wasatch Plateau coalfields of north-central Utah, these operations are generally characterized by multiple-seam mining, cover depths averaging 450 - 600 m (1,500 - 2,000 fl), occasionally extending beyond 760 m (2,500 ft), abrupt cover depth variation due to the overlying canyon/mesa topography, and massive, rigid sandstone roof units. Such conditions encourage severe gate and panel coal bumping, as well as various types of roof instabilities and occasional floor-heave problems. To alleviate these adverse conditions, several mines have employed yield pillars to-reduce hazard-inducing excessive gateroad stress concentrations. This paper describes the evolution of gateroad designs at four of these operations, the specific mining conditions involved, and the general stability performance attained by using yielding gate systems. Mine experiences are "compared" in terms of basic setting conditions, and the general concepts of yielding system applicability and success potential are summarized.

Jan 1, 1993

By Changsheng Song

With increasing depth of coal mining in China, the number of coal and gas outbursts has been increasing for years. By means of destressing the protective seam, the gas in the protected seam is drained to reduce gas concentration in the high gassy seams, thus ultimately attaining simultaneous extraction of coal and gas. Base on the simulated material scale modeling and numerical simulation, the protective seam mining method was practiced at No. 8 coal mine in Pingdingshan city. After extracting the No. 15 seam, the overlying strata movement and the deformation of No. 9-10 protected seam were studied. The experiments showed that it was feasible to destress the protected seams with large interburden thickness. As the protective seam was being mined, the protected seam experienced dynamic movement process and the change in vertical stress in the No. 9-10 seam assumed ?W? shape. When the face had advanced 656 ft (200m) from the setup room, the No. 9-10 seam was fully destressed, resulting in easy gas drainage in the destressed zone. Recommendations on mining sequence of multiple seams mining in the Pingdingshan coal areas were made.

Jan 1, 2008

By Luis Giraldo

The installation procedure of fully grouted rebar bolts requires that the bolt be pushed through the resin grout until it is fully inserted in the borehole. Resin grout is a highly viscous fluid that is forced to flow through the annulus between the bolt and the borehole as the bolt advances. Variables such as bolt insertion speed, bolt vs. borehole diameter and grout viscosity determine the magnitude of the pressure generated ahead of the bolt tip. Under weak rock conditions, the magnitude of the pressure of bolt insertion is often sufficient to initiate hydraulic fracturing along joints or bedding planes that allow injection of grout into the strata leading to significant loss of bolt encapsulation. The grout pressure front has also been linked to gloving, a bolt installation problem that reduces bolt effectiveness. A series of tests were conducted to characterize the pressure of bolt insertion during bolt installation under various conditions. Analysis of the data shows three distinct stages of pressure build up during bolt installation. Understanding of the mechanisms involved may allow development of strategies for controlling the pressure buildup and its negative impact during roof bolting under weak rock conditions.

Jan 1, 2006

By Naj Aziz

n Australia, the common method of laboratory testing of bolt for load transfer capacity determination is by short encapsulation push testing. Some concerns are raised about the validity of the test methodology, as the method does not reflect on the actual load transfer characteristics of bolt in real field situation. Thus, laboratory testes were carried out to examine the load transfer mechanisms of bolts in both the push and pull conditions. Tests were conducted by shearing a short resin encapsulated bolt out of a cylindrical steel sleeve. Three types of bolts with different surface profile configurations were tested. The study was complemented with numerical simulation of the test methods. Irrespective of bolt type the average shear load and shear stress values were found to be greater in push test, and the displacement at peak shear load was greater in pull test. The average shear stifhess values were greater in push test. The numerical simulation of the bolts provided a clear understanding of the stresses and strains generated by different bolt profiles during both the pull and pull testing process, thus allowing a better appreciation of the load transfer mechanism process.

Jan 1, 2005

By David Oyler

Unusual circumstances may require that a longwall retreat into or through a previously driven room. The operation can be completed successfully, but there have been a number of spectacular failures which exposed miners to serious roof fall hazards. To help determine what factors contribute to such failures, the National Institute for Occupational Safety and Health (NIOSH) compiled a comprehensive international database of 130 case histories. The cases include five failures where major rock falls occurred in front of the shields, and six even more serious failures involving major overburden weighting. This suggests two room failure mechanisms. The first is a roof fall type failure caused by loading of the immediate roof at the face as the fender narrows. The second is a weighting type failure caused by the inability of the roof to bridge the recovery room and face area, and affecting rock well above the immediate roof. The data indicate that the roof fall type of failure is less likely when intensive roof reinforcement (bolts, cables, and trusses) is employed together with higher-capacity shields. The overburden weighting failures, in contrast, occurred when the roof was weak and little standing support was used.

Jan 1, 1998

By Joseph C. Zelanko

Cable bolt support techniques. including hardware and anchorage systems, continue to evolve to meet U.S. mining requirements. For cable support systems to be successfully implemented into new ground control areas, the mechanics of this support and the potential range of performance need to be better understood. To contribute to this understanding, a series of 36 pull tests were performed on 10 ft long cable bolts using various combinations of hole diameters, resin formulations, anchor types, and with and without resin dams. These tests provided insight as to the influence of these four parameters on cable system performance. Performance was assessed in terms of support capacity (maximum load attained in a pull test), system stiffness (assessed from two intervals of load-deformation), and from the general load-deformation response. Three characteristic load-deformation responses were observed. An Analysis of Variance identified a number of main effects and interactions of significance to support capacity and stiffness. The factorial experiment performed in this study provides insight to the effects of several design parameters associated with resin-anchored cable bolts.

Jan 1, 1995

By Bruce Hebblewhite

This paper recognises the 25th year of the Morgantown International Ground Control in Mining Conference, by offering a twenty five year review of ground control in the Australian mining industry ? primarily in underground coal. The paper provides an overview of the developments in ground control design methodologies, practices and products. It not only summarises what has been done, but attempts to highlight at least some of the major issues, significant developments, controversies and areas of contention, plus some of the continuing gaps in our understanding or capabilities as we go forward into the next 25 years. Some of the issues included are in relation to: the development of the high strength bolt and cable reinforcement practices widely adopted today and the contrast between stiff and soft systems; a focus on local detail, at the expense of understanding regional stability concerns; dramatic improvements in the use of, and systems available for underground geotechnical instrumentation and monitoring; some of the ground control management trends, including occupational health and safety concerns, availability of suitably trained staff and legislative requirements; the opposing approaches of the empiricists versus the numerical modellers ? is there some middle ground?

Jan 1, 2006

By Ross W. Seedsman

The in situ behaviour of claystone floors associated with the Wallarah, Great Northern and Fassifem Seams has been studied using a comprehensive suite of stress and displacement monitors. The instrumentation was supplemented by in situ and laboratory testing of the claystone materials. The instrumentation demonstrated that the presence of claystone floors is associated with floor heave, extra rib spall, and settlement of the pillar into the floor. Horizontal floor extensometers showed that the depth of extrusion of clay was limited to 1-2 in. A pore pressure transducer installed in a claystone floor demonstrated the possible existence of short-term undrained behaviour of the claystone. Long term swelling of destressed claystone was also documented. Settlement of pillars into claystone floors can be analysed using simple elastic theory. The assumption of plane strain is valid for most claystone thickness/pillar width aspect ratios. Floor heave can be analysed using bearing capacity concepts. However, it is considered that heave is the result of local bearing capacity failure in the rib spall zone. The advantage of this model is that the bearing capacity equation can be applied without resort to unrealistically high factors of safety.

Jan 1, 1992

By J. L. Condon

The Bureau of Mines, through in-house and contract research, monitored mountain bump-prone areas of the Olga #2 Mine, near Welch, WV, using microseismic techniques for 15 months during 1985 and 1986. During this period, two ground failures occurred that were considered "mountain bumps" owing to excessive stress buildups. One failure damaged the roof and 4 pillars around an intersection; the second failure, which released much greater energy, resulted in significant damage to over 100 coal pillars. Analysis of the microseismic data collected provided significant insights into the magnitude and location of each failure. The actual failure zone was clearly delineated prior to the mountain bump occurrences through analysis of source locations of each microseismicevent. Trends in cumulative rate plots indicated the onset of structural instability. Although the data could not be analyzed automatically, the significance of the data interpretation cannot be overemphasized. Microseismic monitoring of bump-prone areas can be successful in providing a means to actually observe the structural stability occurring in underground coal mines. This paper discusses data collection techniques, analysis methods, and implications of the monitoring technique, with special emphasis on actual data from two large mountain bumps in West Virginia.

Jan 1, 1987

By K. Y. Haramy

Strong roof helps minimize roof fall problems in coal mine entries. However, the Inability of strong roof to cave readily may contribute to major ground control problems In Iongwall and retreat mining operations. The concern expressed by mine operators prompted this Bureau of Mines study to analyze the effects of strong roof members on ground stability around Iongwall openings. The problem was approached from three directions: development of a theory to analyze the strain energy conditions In the coal and surrounding strata, modeling the effects of different thicknesses and strengths of Coal and roof strata, and field Instrumentation of powered supports In two Iongwall mines. Results from the theoretical and modeling analysis confirm the accepted belief that a strong roof does, In fact, play a major role in high stress concentration problems In and around the Iongwall panel. Analysis of the effect of different roof overhang dimensions and properties on relative strain energy buildup In the coal and roof Is presented. Shield pressure data Indicate possible methods for detecting noncaving roof behind the shields. Strategies to monitor roof overhang and control dangerous conditions caused by the noncaving roof are also presented.

Jan 1, 1988

By Lu Jiam Zhang

Coal and gas outburst is one of the serious natural disasters in the coal mines of China. Since 1950, more than 10,000 coal or gas outbursts have occurred in more than 200 underground coal mines of different types. The outburst prone coal mines are widely spread out. It occurs in different types of coal -ma and is very serious in some areas. Most outbursts occurred at the time of roadway driving in coal seam, serious outbursts occurred mainly when entering the coal seam during the cross-cut driving; of the outbursts, coal and gas outbursts We UP major proportion, while pressing out and pouring out ah account for a large proportion; outburst. occur under different operating conditions, but mostly occur during shotfiring. This paper introduces the prevention and control measures as practiced in China and illustrates the three types of outburst cla8sification. Both technology and management are equally important in outburst prevention and control. Measurement of the volume of drilling cuttings and the initial gas outflow rate fm- boreholes have proven to be effective. A special team and organization must be set up to deal with the problems.

Jan 1, 1987

By Michael Kelly

Current research in longwall mining in CSIRO Exploration & Mining is focused within five major projects and several minor projects. The major projects are: 1 3D Aspects of Longwall Geomechanics. This was reported to the conference last year and a final report will be available by mid-2001. 2 Mine Gas Control. This just completed project centred on Dartbrook Colliery which has a longwall gas make of more than 8 cubic metres per second. 3 Rapid Roadway Development This includes the construction of an autonomous conveying and bolting module (ACBM) that sits between the miner and haulage system. 4 Top Coal Caving In conjunction with the YanKuang group in China, CSIRO and the University of NSW are conducting a prefeasibility study of the Top Coal Caving method in Australian conditions. 5 Longwall Automation. In partnership with the Cooperative Research Centre for Mining Technology and Equipment (CMTE), the CSIRO has conducted a scoping study on this issue and will commence an initial three-year demonstration project in July this year. This paper describes these protects in more detail with particular focus on the last three in the above list.

Jan 1, 2001