Search Documents

By Jeffrey M. Listak

This report describes a study, conducted jointly by BethEnergy Mines Inc. and the Bureau of Mines, to assess the effects of longwall front abutment loading on various supplemental support materials utilized in a predriven recovery room. The purpose of the predriven recovery room is to reduce longwall equipment transfer time by eliminating the premove preparation associated with conventional recovery methods. In addition, the room provides a large area in which face salvage equipment can maneuver. Results of four recovery-room study areas show the progression and influence of the front abutment on the longwall panel and supports and their subsequent behavior. The best performance (i. e. the support that most facilitated recovery) of support material was achieved through the use of a concrete mixture which had a sand content of 35 percent by volume. The longwall transfer time was reduced by 30 percent which translates to a production advantage of 37,000 raw tons of coal per panel.

Jan 1, 1989

By Andreas Hucke

For the roadway design in the German hard coal mining industry, an advanced combined planning system has been applied during the past 20 years. The German mining industry is working with single entry roadways system. After first longwall passage the roadways will be stabilised with side wall building material packages. Later this roadway will be used again for the second retreating longwall. The intention of the implementation of several different design methods for the planning of the roadways is to enhance the reliability of the results. On one hand the planning system uses numerical simulation and physical modelling in addition to analytical and empirical methods. On the other hand in-situ monitoring and analysis during the roadway development will be used to verify and calibrate the numerical and physical models. Especially before the implementation of new support elements in underground, this system is suitable and reasonable because the new support elements will be tested in the physical and numerical simulation prior to cost intensive underground tests. The interaction between the numerical and physical modelling in comparison with underground monitoring and analysis during development and the later use of roadways will be shown with some examples. The first example shows a rock bolted rectangular roadway which will be mined at both sides of the roadway. Different support and roadway building material package systems are investigated under various stress conditions. The results are utilised to optimise the roadway support and the roadway side package systems. The influence of different points in time of the installation of several support elements in a combined arch and bolted roadway is shown as another example. Two different types of support systems are compared within the physical models. These models are used as a base for ongoing numerical analysis and simulation to find out the ideal point of time to assemble the different support elements. The last example handles the influence of slickensides in the roof of arch shaped roadway on their stability. Different slickenside positions and densities are investigated and classified.

Jan 1, 2006

By Vincent A. Scovazzo

"The most significant study on the effects of longwall mining on gas and oil well integrity was completed by a consortium of coal and shale gas industry participants. A field study was conducted in 2013 and 2014 and is referred to by its location on Well Pad NV-35. The experiment site was located at the CONSOL Enlow Fork Mine in Washington County, Pennsylvania.The experiment was completed to verify John T. Boyd Company (BOYD) calculations and studies completed under contract by for the Pennsylvania Department of Environmental Protection Gas Well Pillar Study Update. The findings of the original study were presented by BOYD at the 32nd Conference, while numerical analysis of the Well Pad NV-35 field study was presented by Dr. Su at the 35th Conference.This paper addresses the findings of the experiment and how it confirmed the conclusions of the original study.INTRODUCTIONA field study was conducted in 2013 and 2014 by a consortium of coal and shale gas industry members to test the effects of longwall-induced ground movement on the stability and integrity of wells drilled through a gateroad abutment pillar. The project was initiated to test initial John T. Boyd Company (BOYD) findings of the Gas Well Pillar Study Update (Scovazzo and Moran, 2014), completed for Pennsylvania Department of Environmental Protection, Bureau of Oil and Gas Management (PDEP). Background and initial findings on this project were presented at the 32nd Conference (Scovazzo and Moran, 2012). The field work and numerical analysis were spearheaded by CONSOL Energy, Inc. (CONSOL) with participation by Chevron, EQT, Noble Energy, Range Resources, Marcellus Shale Coalition, and the Pennsylvania Coal Alliance.Dr. Wen H. Su of CONSOL was the leader of the field experiment with input from the participants. Dr. Su also completed numerical analysis of the results and model casing deformation. Analytical results were presented by Dr. Su at the 35th Conference (Su, 2017)."

Jan 1, 2018

By Jennifer Riefenberg

Ground control hazards, coal quality, ore reserve estimation, and pollution modeling seem unrelated topics from most mining perspectives. However, geostatistical methods can be used to characterize each of these, and more topics. Exploratory drill core data, and continued drilling and field measurements, can provide a wealth of information related to each of the above areas and are often severely underutilized. Recent studies have led to the development of the Multiple Parameter Mapping (MPM) technology, which utilizes geostatistics and other numerical modeling methods, to generate a "hazard index" map, often from exploratory drill core data. This mapping has been presented for ground control hazards relating roof quality, floor quality, numerically modelled stresses due to mining geometry, and geologic features. A review of the MPM method, future directions with the MPM, and a discussion of using these and other geostatistical methods to quantify coal quality, ore reserve estimation, and pollutant modeling are presented in this paper.

Jan 1, 1996

By C. Fairhurst

Most of the papers designated as being within the topic of underground storage at this Symposium are concerned with aspects of radioactive waste isolation. Although this is, unquestionably, an important international application of underground storage, and one involving a considerable number of research investigations, the subject of underground storage is indeed much broader. Several major international conferences have been devoted exclusively to it. Applications include storage, under a range of temperatures and pressures, of oil and liquefied petroleum products, compressed air, heat, foodstuffs of various kinds, hazardous and 'nuisance' industrial by-products, and a variety of special applications, both civilian and military - some in use, others proposed. Storage may be in caverns excavated specifically for the purpose, exhausted mines may be adapted for storage or, in some cases, the material to be stored may be injected under pressure into the pore spaces of porous-permeable formations at depth. A variety of rock types and geological environments are used, e.g. excavations in salted or domal salt, where long-term creep closure of the openings is a concern; massive granite, where fluid loss through fissures may be important. Cavities may have spans of several tens of meters, and there is interest in achieving still larger excavations. As would be expected, this breadth of underground storage applications introduces a similarly broad range of questions in rock mechanics and rock engineering. The report will review these questions and recent developments in rock mechanics research, computational procedures, and design applications - and will also discuss the opportunities for a still greater range of applications of underground storage to current industrial and social problems.

Jan 1, 1989

By John Hoelle

Coal mines in southern West Virginia, south-western Virginia and eastern Kentucky have experienced coal bumps at least since 1933. Most of the bumps have occurred due to high cover, strong roof and floor strata and stress concentrations due to the mining sequence. A longwall mine in eastern Kentucky first experienced coal bumps on the tailgate side of the longwall face in 1989. The bumps continued until 1996. The bumps were the result of: Thick overburden up to 2200 feet Strong roof and floor (strata strengths up to 25,600 psi UCS and elasticity modulus up to 4,800,000 psi Previous over-mining in places Sandstone channels Not all characteristics occurred simultaneously. The bumps produced seismic events recorded up to 4.3 (Richter scale magnitude), and damaged pillars that were up to 147 by 152 feet in size.

Jan 1, 2008

By Ming Ju Liu

China has been suffering from the most serious coal and gas outburst accidents. The situation has become worse than ever with the mining of deeper coal seams at higher production rates in a more complex underground mining environment, in order to meet the huge national demand for coal-fuelled power plants. In the year 2007 alone, more than 30 outburst accidents occurred in underground coal mines with a death toll of 258, and in the year 2008, as of May 22, nine outbursts have already occurred in Henan, Hubei and Chongqing, killing 68 workers. At the same time, China also experienced new trends of coal and gas outburst accidents since its coal production boom in the year 2001. These trends are of great importance for government agencies, coal mine owners and operators to take initiative and effective measures to prevent and control the occurrence of coal and gas outbursts in China?s widely spread outburst prone mining areas. This paper presents outburst data of China coal mines since 2001 and describes new trends of outburst occurrence in recent years, which include outbursts coupled with shocks or rock bursts of competent roof, outbursts in mines under development, outbursts in new mines and mines that have never suffered outbursts before, outbursts in mines that are believed to be of low gas content as well as outbursts in more long-wall faces. Based on the observation of outburst occurrence in China in the period from 2001 to 2008 as well as mining and geological conditions, detailed analysis of the possible causes that led to those new trends of outburst accidents is conducted. The analysis helps shed light on possible future remedies and the necessary measures to alleviate or eliminate outburst accidents in underground coal mines. Suggestions are put forward on future studies that could be of interest to national and provincial government agencies regarding strategic policies, proper technical management practice, identification of outburst prone coal seams, online monitoring of impending outbursts as well as prevention and control measures.

Jan 1, 2008

By G. R. Corbett

The introduction of roof bolts to Phalen Colliery in the Sydney Coalfield, Nova Scotia (annual output of 2Mt) has been successfully implemented in maingate and tailgate entries over the last four years. Monitoring of the roof bolted areas continues to be an integral part of the quality control program as the results are utilized to maintain safety and to aid in long-term design strategies. Although all gateroads in the Phalen Colliery have converted to roof bolts as their primary means of support, the majority of intersections which intersect the main slopes remain supported by large steel structures. Several intersections within the Phalen Colliery were monitored as they were created by the mining process. A comparison is made between intersections supported with only traditional 6.4 to 6.7 m steel structure and intersections supported by 2.44 m fully resin encapsulated roof bolts in conjunction with 7.6 m fully cement grouted cable bolts. Detailed monitoring was conducted using CA NM ET's intrinsically safe sonic probe extensometer datalogger which has the ability to read up to sixteen probes simultaneously at programmed intervals. The density of the data from the datalogger has allowed a better understanding of the deformation of cable bolted intersections than was possible with manual monitoring. Test results have helped mine operators to design safer cable bolted intersections.

Jan 1, 1995

By John Latilla

Exxaro Mining?s Matla Coal situated in Mpumalanga, South Africa operates two shortwall faces on the No 4 and No 2 seam while the No 5 seam has also been longwalled in the past. Severe strata loading events have lead to a number of serious roof falls on the wall face (facebreaks) resulting in safety threats as well as considerable production losses. In 2002 the No 4 seam shortwall suffered a facebreak restricted mainly to the tailgate side of the mining panel due to a thick, near surface dolerite sill not breaking properly. This was partly due to the premature suspension of longwalling in the overlying No 5 seam. The resultant overloading lead to severe pillar damage and subsequent bord collapse. Surface pre-split blasting was successfully used to relieve the pressure as well as to pre-condition the dolerite above the following two panels. The shortwall on the No 2 seam has experienced mid-face loading due to No 4 seam chain pillars lying over this area and creating a secondary cantilever effect. Pre-split blasting of the solid rock above the No 4 seam pillars has resulted in a significant reduction in the number of facebreaks. The panel layout of the No 2 seam was subsequently changed so that the chain pillars on both the No 4 and No 2 seam are superimposed whereas previously they were offset.

Jan 1, 2007

By Andrew P. Schissler

The Citronen Zinc-Lead Project is one of the world?s largest undeveloped zinc-lead resources, containing more than 13 billion pounds of zinc and lead metal. The project is located in northern Greenland, a self-governed region of the Kingdom of Denmark (Figure 1). Citronen is the northern-most mine in the world, operating at a latitude of 83o 3? N. In excess of 67,000 meters of diamond drilling have been completed to delineate the resource. As of January 2012, the measured, indicated, and inferred reserves for the Citronen project totaled 70.8 million tonnes, consisting of 5.7% zinc + lead (3.5% zinc cut-off) (Ironbark, 2012). For the underground mine plan, room-and-pillar and long holestoping mining methods were selected. The beneficial application of structural fill was considered for increased recovery, efficient tailings disposal, and ground control. Three types of fill were compared - paste fill, cemented rock fill, and iced tailings. An environmental and economic feasibility study concluded that iced tailings was the preferred alternative provided it met the ground control requirements. The purpose of this paper is to explain the investigatory steps that led to the possibility for the use of iced tailings as structural fi

Jan 1, 2012

By Gennaro G. Marino

As part of the development of a shopping center in West Virginia, a significant bench had to be cut into a mountainside that was over 700 ft. high. As a result, a steeply stepped, over 400-ft.- high wall was created. The high wall exposed old abandoned room-and-pillar coal workings at the toe of the cut. Because of exposure to the elements, the mine openings began to severely deteriorate with significant potential of undermining of the rock cut face and causing a large rock fall(s). Exacerbating this wall problem was a set of fairly planar sub-parallel and sub-vertical joints creating, in essence, thin rock slabs. Also present were stress relief fractures that were observed in the exposed pillars. Given the proximity of the project building to this high rock face, mitigation of the rock fall potential was deemed necessary. In order to prevent continued damage and deterioration of these exposed mine entries, the rubblized openings were filled with bulkhead grout and pressure injected with grout. The total amount of grout installed in these openings was about 3,945 CY. Also, a rock drape was attached to the entire face to mitigate small rock falls from natural causes. There also existed another level of mining below the ground surface and under an existing building at a depth of about 160 ft. Under a portion of the building, the pillars in these old works were second mined, and the building seemed to have been already affected by limited subsidence above this area. Also, calculated pillar safety factors in this high extraction section of the mine were too low. Consequently, these old works were stabilized by saturation grouting. An indication of overall roof distress was the significant fracturing encountered in the bedrock overburden during the drilling of the injection holes and the volume of grout placed in these holes. The total grout installed in the high extraction section of the lower mine was about 6,660 CY. This paper describes the investigation and the grouting techniques employed at the rock cut face and under the existing building to mitigate continued damage to avoid future subsidence problems at the face and the building premises.

Jan 1, 2013

By S. L. Huang

The location and shape of potential failure surfaces in soil slopes were directly determined based on the stresses induced in the soil mass and the strength of the soil itself. Stress calculations were carried out by the finite element method with the Drucker-Prager nonlinear material model. The Mohr-Coulomb failure criterion and Mohr's circle stress analysis were then applied to the calculated stresses to determine the characteristics of the failure surface.

Jan 1, 1989

By Rob Thomas

Strata management is a critical and now necessary requirement in the New South Wales underground coal mining industry. As a formal and structured process, strata management allows ground support and mining methods to be tailored to the anticipated and encountered geotechnical environment in a controlled manner. In its application, strata management therefore enables operators to identify and control geotechnical hazards and the risks they pose to the mining operation, including risks to personnel safety and mine production. The paper considers recent developments in strata management in the New South Wales underground coal mining industry. Points covered include the statutory requirements stipulated in the Coal Mine Health and Safety Regulations, Geotechnical Hazard Plans, tiered support plans, the Authority to Mine concept, Trigger Action Response Plans and monitoring. Several successful and unsuccessful case studies are included which make specific reference to roadway development and longwall retreat and in doing so, the unique demands imposed by these two different aspects of the mining operation on strata management.

Jan 1, 2007

By S. Yamashita

Recently in Japan, unexpected degradation (surface subsidence) at old underground quarry sites, such as 'Ohya-Ishi' (pumice tuff) pit field has often been occurred. At these quarry sites, the excavation was started 20 or 30 years ago with mechanical chain cutter and the Room and Pillar method, and stopped 7 or more years ago. Therefore, a reliable method has been required for an estimation of long term mechanical properties of the rock and for an observation of a stability of rock-pillars or structures. In this study, creep tests under uniaxial compressive load were carried out on the 'Ohya-Ishi', with the aim of estimating the long term stability of the rock. From these results, a creep mechanism of the rock was discussed using the failure mechanism hypothesis proposed by Bieniawski and by others. On this basis, critical time to failure was predicted by the relationship between the logarithm of life time and stress ratio of the sustained axial creep load. Additionally, outline of the monitoring system of AE/MS activity in the field, which have set by the Ohya Aria Consolidate Public Corporation and the others to predict or to prevent the degradation of those residual pillars, is to be reported. Key words : Ohya-ishi, Pumice tuff, Mine pillar, Long term stability, Creep, Critical time

Jan 1, 1996

By Zhijie Zhu

In order to determine the overburden failure characteristics of extra-thick seam mining, EH4 electromagnetic image system and borehole televiewer survey were applied to panel 8100, Tongxin coal mine. EH4 electromagnetic imaging system was used to map the overburden strata before and after mining. Analysis of the distribution of the electrical conductivity showed that the fractured zone height was 492-558 ft (150-170m); Observation through the borehole televiewer showed that the fractured zone height of water conductivity (or water flowing fractured zone height) was 110m-142m. The results of the two methods showed that the fractured zone height of water conductivity was 492-558 ft (150- 170m) or 10-11.3 times the mining height.

Jan 1, 2014

By W. M. Pytel

The applicability of the beam theory in analysis of roof- pillar-weak floor interaction in partial extraction room-and-pillar mining is presented. The mine structure is modeled as an equivalent multi-indeterminate overburden elastic beam supported by elasto-plastic pillars; resting on a viscoelastic layer of immediate weak floor strata underlain by a competent rock mass. The developed analytical model was initially utilized to conduct sensitivity analyses of different variables affecting the mining system, such as the deformability of coal and weak floor strata, thickness of weak floor strata, number of pillars in a panel, width of pillars, width of panel etc. These analyses were then extended to three overburden strata - coal pillar - floor strata lithologies typical of active coal mining areas in Illinois.

Jan 1, 1989

By Eric C. Poeck, Ryan Garvey, Ugur Ozbay, Kun Zhang

"A coal bump is characterized by the sudden failure of one or more pillars and an associated release of kinetic energy. Although the geologic conditions surrounding coal bumps are often similar, their occurrence and magnitude are difficult to predict. This paper presents the development of an approach to assess the potential for coal bumps in room and pillar mines through the use of energy concepts and special consideration of the interface properties between the coal and overlying rock. Back analyses were performed on the widespread collapse of a room and pillar mine with an associated 3.9 local magnitude seismic event. Pillar and mine-scale models were constructed using the distinct element method to simulate the mining stages leading up to the collapse. A variety of loading conditions, material properties, and interface properties were evaluated for their effect on unstable failure of single pillars, and the mine-scale model was used to study the evolution of failure during progressive mining. The extent of unstable failure was quantified in these models by calculating the total kinetic energy released during each mining stage. Through the parametric analysis of single pillar models, it was found that softening parameters in either the coal or the coal/ rock interface can individually facilitate unstable failure of pillars, but the combination of the two in a single model produced a much higher release of energy during failure. The results of the minescale model further illustrated the trend as the combination of softening parameters in the coal and coal/rock interface produced a series of failures that most accurately reflected the collapse event at the mine. The method of room and pillar stability analysis demonstrated in this study effectively explores the potential for large coal bumps.IntroductionThe analysis of coal pillar behavior is challenging because natural variability in geologic conditions requires estimation of material strengths and predicted loads for a given mining situation. Large width-to-height (w/h) ratio pillars and deep overburden present an additional challenge, as the failure behavior of such pillars is more complex and may involve unstable, sudden collapse. Empirical methods have improved the success of coal pillar design for a wide range of conditions, but, for deep cover and squat pillar (w/h > 10) geometries, pillar performance predictions are not as accurate (Mark, 2000). As with any empirical approach, more back analysis and the consideration of new variables may help improve understanding and accuracy of future designs."

Jan 1, 2015

By J. A. Nemcik

Although floor failure at longwall faces has been traditionally associated with a soft floor, in many csses floor buckling has been observed just ahead of the longwall supports, despite the floor being a competent rock The floor failure is associated with the presence of weak bedding planes in the floor and the movement of strata towards the goaf opening. This paper presents the principles of the floor failure based on numerical modelling and field observations and outlines the practical approach to estimate the risks involved with floor failure.

Jan 1, 1995

By Murali M. Gadde

Perimeter mining is a special form of very productive partial extraction method practiced at some mines in the United States. In the Illinois Basin mines where all major coal seams have weak underclay in the immediate floor, experience shows that any long-term ground control issues will arise due to floor failures rather than instability of the coal pillar itself. While there is a significant amount of work done on floor stability associated with regular pillars, no work has been done so far on the stability of perimeter pillars. This paper reports the results of a comprehensive study that was conducted for the first time on floor stability during perimeter mining in the Illinois Basin mines. A special plate template, which mimicked a common perimeter pillar configuration was created to conduct in-situ bearing capacity tests at five mines in three states of the Basin. Additionally, because of the complex shape of pillars created in perimeter mining that defies any closed-form solution, floor bearing capacity was studied using three-dimensional nonlinear numerical modeling. Based on these in-situ and numerical studies, some guidelines are provided for perimeter pillar stability analysis.

Jan 1, 2009

By Arthur Miller, Andrew Weakley, Heather E. Lawson

"IntroductionDynamic failure events in an underground coal mine, or “bumps,” are defined as “the sudden, violent bursts of coal from a pillar or pillars or a block of coal, resulting in a section, the whole pillars, or the solid block of coal being thrown into an open entry” (Peng, 2008). Reports of disastrous and often fatal dynamic failure events date back over one hundred years in the United States. Mining practices and technologies have significantly evolved over the course of the last century, yet these events continue to occur. The events at Crandall Canyon, Utah (Gates et al., 2007) and Brody No. 1 Mine in West Virginia (Barker and McNeely, 2014) are two recent failure events that resulted in a total of eleven fatalities. These events testify to the fact that dynamic failure remains an imperative safety concern. Furthermore, their continued occurrences indicate that engineering controls have proven inadequate at wholly mitigating the problem.Multiple conditions have been associated with the occurrence of dynamic failure phenomena, including• thick, competent strata that can create a bridging effect, resulting in high abutment stresses (Rice, 1935; Holland and Thomas, 1954; Iannacchione and Zelanko, 1995; Agapito and Goodrich, 2000; Peng, 2008; Whyatt, 2008; Whyatt and Varley, 2010)• overburden thicknesses greater than 500–700 ft. (Rice, 1935; Peng, 2008)• a strong coal that is resistant to crushing (Rice, 1935; Peng,2008) or that is “uncleated or poorly cleated, strong…sustains high stress and tends to fail suddenly” (Agapito and Goodrich, 2000)• the presence of sandstone channels or rolls that can serve to concentrate stresses (Iannachione and Zelanko, 1995; Agapito and Goodrich, 2000)• fracturing of strong units above or below the coal seam (Whyatt and Varley, 2010)• slip along pre-existing discontinuities (Peperakis, 1958; Whyatt and Varley, 2010)• multiple seam mining interactions (Campoli, Kertis, and Goode, 1987; Iannachione and Zelanko, 1995; Newman, 2002; Peng, 2008)• mining sequences that can cause anomalously high stress concentrations (Campoli, Kertis, and Goode, 1987; Iannachione and Zelanko, 1995)"

Jan 1, 2015