Search Documents

By Weidong Pan, Yinchao Yang, Baodong Zuo

Fully mechanized mining technology, with a large cutting height in thick coal seam, has been developed to be large-scale, mechanized, and intelligent. Furthermore, it is also superior to other mining methods because it operates more efficiently and has higher recovery rates of coal resources. Dongpang coal mine (located in north China) is one of the largest coal mining productions in Hebei province. It is significant because it is the first set of coal mines in China to adopt fully mechanized mining technology that has large cutting height potential. When looking at the coal seams of deep mining, specifically in the mine No. 2612 where the working face is 4.5–6.5 m cutting height, the coal walls have low stability due to the way the coal seam fluctuates in a large working face. This paper adopts mechanical analysis, numerical simulation, and field observation research methods to control the rib fall of coal walls in a coal mine. By adopting research methods that analyze the mechanical characteristics of face roof, we are able to conclude the main roof structure of the masonry seam stability criterion in overhead mining with large cutting height. This is done through employing the numerical simulation method, which helped to determine the main factors that influence the rib fall of a coal wall and weighting factor. Through field observations, we discovered the technology method to relieve, control, and mitigate rib falls of coal seam in a coal mine. We also discovered methods that would ensure the smooth mining of the working face of the mine by strengthening the bolting and grouting reinforcement methods used to improve the working face of stope surrounding rock conditions. This paper discusses research results that enrich the stope wall rock control method by expressing how fully mechanized mining technology, with a large cutting height, is meaningful to solve the complex conditions of rock fall caused by thick coal seam.

Jan 1, 2017

By Brian Clifford

Thoresby Colliery is in the process of recovering an old roadway that was flooded following the closure of an adjacent mine. The aim is to re-use the roadway as a gate road for a longwall retreat panel and it is therefore important to establish the condition of the existing rockbolt support during the recovery operation. Two NDT methods, ultrasonics and RMT's newly developed RF (Radio Frequency) system were used in combination to interrogate the rockbolts to determine their condition. This paper describes the condition of the rockbolt supports, the NDT methods used and the problems that had to be overcome to successfully apply the two methods.

Jan 1, 2002

By Keith Heasley

An eastern longwall mine was required to mine through a set of three entries located midway down the length of a panel. Of course, the mine desired to design a successful support system for the mine-through area at the least cost. To further complicate the design process, the mine-through entries were located directly under the end of a previously mined, overlying longwall panel and the entries were close enough to be subject to stress interactions from the overlying seam. In order to accurately evaluate the multiple-seam stresses and modify the mine-through support system appropriately, the boundary element program LaModel was used to model the stress and displacements in the two mines. Using the results of the model's stress analysis, the support density was systematically varied throughout the mine- through entries for optimum sup@ efficiency and economics. During the actual mining of the cross panel entries, the longwall experienced few, if any, additional delays, and overall, the support and mine through of the cross-panel en- tries at Harris #1 was very successful, saving the mine confineable time and money.

Jan 1, 2003

By L. Z. Wojno

Tunnels in South African gold mines are developed at depths down to 3 600 m below surface where the virgin rock stress approaches 100 MPa and, on occasions, through rock where the field stresses exceed 150 MPa. In addition, many tunnels are subjected to increases in field stress of over 50 MPa during their useful lifetime. As a consequence, the walls of most tunnels are fractured causing the rock to dilate into the tunnel. Quantitative data on the extent of this fractured zone are presented. The function of support in these circumstances is to reinforce and maintain the integrity of the fractured rock. In 80 per cent of the 800 km of tunnels developed annually, the support methods used are capable of maintaining the stability of the tunnels. However, the remaining 20 per cent of tunnels is subjected to severer conditions where dilation in excess of 250 mm occurs and/or where the probability of strong seismic ground motion is high. In these tunnels, additional support is required. The type and pattern of support for both normal and severe conditions is described. In spite of the improved support used, damage to tunnels may occur. To minimize this damage, the concept of a rock reinforcing tendon that will yield and do work, when subjected to quasi-static or rapid deformation, has been put forward. Specifications for such a tendon are presented and the development of certain yielding tendons are described.

Jan 1, 1987

By Robert W. Bruhn

A 125 foot high steel lattice frame tower supporting a 500 kV EHV transmission line and located over the gateroads of a longwall mining operation was subjected to ground movements from the mining of adjacent longwall panels. Under an agreement with the owner of the powerline, the mine operator was required to minimize mining impacts on the transmission line. In view of this requirement, the mine operator prepared a forecast of the expected subsidence ground movements prior to the onset of mining. These forecasts, in conjunction with finite element analyses of the tower superstructure under the imposed ground movements and wind loadings. suggested that the structural capacity of the tower would probably be diminished little, if at all, by mining. Ground movements determined by survey during mining of the two longwall panels were found to be in close agreement with predictions. Strains measured in selected tower members during mining generally agreed with values calculated by the finite element analyses. The study confirmed a methodology to predict subsidence and to assess its effects on steel lattice transmission towers.

Jan 1, 1990

By L. Mahony

This paper describes the design, construction and commissioning testing program for a laboratory facility at the School of Mining Engineering, UNSW, Australia, aimed at evaluating reinforcement tendon performance when subjected to shear loading. The project has been financially supported through the coal industry ACARP research initiative. The single failure plane design adopted in the test rig has been successful in allowing shear loading to be directly applied to fully installed (and where relevant, pre-tensioned) rock bolts. Initial results are extremely encouraging, and illustrate a significant axial component of load development as shearing takes place - particular in lower strength, softer material types. The paper also outlines future plans for use of this facility.

Jan 1, 2005

By Kot F. Unrug

Since the introduction of longwall systems, the prediction of roof behavior and support requirements have become the major issue referring directly to safety as well as productivity. In more recent times, and especially in the USA where longwalls are exclusively equipped with costly hydraulic self- propelled support systems, a decision whether a longwall is applicable in a given condition, and when so, what kind of equipment should be selected, is of primary importance. There are numerous examples where lack of experience, and subsequently wrong selection of supports or winning machines, resulted in considerable losses. It should be emphasized that careful studies of prevailing geological and mining conditions, especially in a new area, are required to assure a successful operation. An evaluation of the conditions can be carried out in different ways utilizing such methods as: - Theoretical approach. applicable when geological conditions comply with the theoretical assumptions. - Empirical relationship which gives satisfactory results where the coefficients could be adequately determined. - Structural geological studies which must be undertaken in all cases, since the frequency of fractures and their orientation have a prevailing influence on roof behavior. - Scale model study on equivalent material for determination of failure conditions in the roof and mechanism of movement (flow) of broken rock matter. Coefficients for empirical formulas can be determined by these types of studies, as can boundary limits for mathematical modeling. - Mathematical modeling, e.g., finite element analysis. - Measurements and observations taken underground during the development period end utilization of experience for previous longwall panels in the area. Usually it is the most practical method where mining and geological conditions are comparable. An application of me or more of the above approaches remains to be a matter of judgement for particular conditions, however, the utilization of a practical experience, when available, is usually the safest way for planning a successful longwall operation.

Jan 1, 1982

By Mostafa Sharifzadeh, Ebrahim Ghasemi, Kourosh Shahriar

"The Tabas Central Mine (TCM) is one of the underground coal mines located in the Tabas coal region, in the mid-eastern part of Iran. This mine is the first mechanized coal mine in Iran that uses the room and pillar method. Pillar design is one of the most important issues in underground coal mines, especially in room and pillar mining. In this paper, a new method for coal pillar design in the main panel of TCM is presented. This method is able to estimate the magnitude of the various loads (both development and abutment loads) that pillars might experience throughout the mining process. Also, the method reduces the pillar failure risk. Based on this method, proper pillar sizes in TCM are obtained (11.6 x 11.6 m (38.l x 38.1 ft)).INTRODUCTIONPillar design and stability are two of the most complicated and extensive mining problems related to rock mechanics and ground control subjects. Although these problems have been investigated for a long time, to date only a limited understanding of the subject has been gained. Prior to this, the dimensions of a pillar were largely determined by experience based on trial and error, intuition, or established rules of thumb; any research available tended to be isolated and sporadic. But nowadays, various pillar design formulas have been developed based upon laboratory testing, fullscale pillar testing, and back-analysis of failed and successful case histqries. In 1980, a number of ambitious field studies conducted by the U.S. Bureau of Mines developed the ""classic"" pillar design methodology. It consisted of three steps (Mark, 1999, 2006):1. Estimating the pillar load using tributary area theory2. Estimating the pillar strength using a pillar strength formula3. Calculating the pillar safety factorAlso, Bieniawski (1981) presented a step-by-step method to determine coal pillar dimensions in room and pillar mines. In this method, similar to the classic method, pillar load is estimated by using tributary area theory.Currently, in mqst of the room and pillar mines, remnant pillars in panels are recovered by retreat mining (pillar recovery). Hence, the above mentioned methods are not appropriate for pillar design, because in these methods pillar load is estimated by the tributary area theory, and the effects of abutment loads, which result from retreat mining and the creation of a mined out gob, are ignored. Abutment loads affect the pillars in the adjacent of pillar line and a load greater than what is estimated by tributary area theory is applied on the pillar. So, pillar design without considering the abutment loads leads to pillar failures during retreat mining. Pillar failures continue to be one of the greatest single hazards faced by underground coal miners. Pillar failures are responsible for unsatisfactory conditions, which include the following (Mark et al., 2003):"

Jan 1, 2010

By Jingyi Cheng

Many longwall panels in China are laid out along the dip direction such that the direction of longwall retreat mining is along the strike direction of coal seams. Downward mining longwall panels in steeply inclined seams refers to those that are laid out in a non-uniformly developed fold structure where the seam is not only steeply dipping, but also highly undulated along the strike direction, causing longwall mining extremely difficult because it has to deal with large dip angles that vary both in the mining and faceline directions. Obviously, the characteristics of mine pressure and overlying strata movement in downward mining longwall panels in steeply dipping seams have unique patterns that are very much different from those cases of mining the flat or gently inclined coal seams. The effects of those unique patterns presented a big challenge to production and safety. Almost all previous and current researches on ground control have been concentrated on issues related to the flat and gently inclined coal seams. Conversely, research on steeply inclined coal seams, especially those with large angle variation both along the seam dip and strike directions is almost none. Therefore, it is very important to initiate a study to better understand the characteristics of mine pressure and overburden strata movement for this special type of geological condition. The objective of this paper is to monitor and analyze the characteristics of mine pressure and overlying strata movement in downward mining longwall panels in steeply inclined seams, the angle of which varies greatly along both the seam dip and strike directions. The measured data has conclusively demonstrated that the characteristics of mine pressure and overlying strata movement in downward mining longwall panels in steeply inclined seams are different from those for the flat and gently inclined coal seams. The large downward angles of coal seam undulation along the strike (mining) direction can obviously affect the roof movement and reduce strata pressure. Study in this research showed that appropriately increasing the rate of mining (or face advance) is positive to roof control.

Jan 1, 2013

By Monte R. Hieb

Study of moisture-induced swelling strain in Pennsylvanian Period rocks of the Appalachian Plateau in West Virginia shows a 2:1 biaxial horizontal anisotropy which trends NW-SE. Oriented in-situ slabs of coal mine roof rock were collected across West Virginia, dry-sawed to size, air-dried to stability, and then monitored for moisture changes and deformations in the horizontal plane through one wetting cycle and drying cycle. Biaxial swelling strains were exhibited in nearly all rocks tested, with maximum horizontal deformations occurring normally-incident to the strike of regional geologic fold structures. This relationship persists as fold strike varies across the study area. A connection with Alleghanian fold development and/or post-Alleghanian fold relaxation is suggested. Deformations were largest in shales, but occurred in sandstones and siltstones as well. During testing, moisture-induced fractures (MIF) developed parallel to the regional fold structure and ranged in size from hairline cracks to sample-destroying cracks that were orthogonal to the observed biaxial swelling strain direction. Preferential wetting and swelling of clay minerals along NE-trending fractures, related to a fold-parallel fracture fabric of regional extent across West Virginia, is the most likely reason for the observed systematic NW-oriented biaxial swelling strains. The testing methods used in this study are simple and inexpensive and produce robust results that offer insight into a regional, anisotropic mechanical weakness that imparts a dynamic, asymmetrical horizontal stress to moisture-sensitive coal mine roof rocks over time. Because a similar mechanical fabric has been reported in Devonian-age shales, these findings may have implications for shale gas developers in the Appalachian Basin challenged by rapid aperture closure rates along horizontallydrilled induced fracture networks in Devonian rocks like the Marcellus Shale. The paper concludes with an example of how the concept of a preferred swelling strain direction might be applied to improve the effectiveness of roof trusses.

Jan 1, 2013

By Erdal Akyol

The rockbolting method of support is employed widely in several countries in different of mines. Hard rock mines use this method extensively. Soft rock mines, such as coal mines, have employed standing supports (steel sets) as the main method, although some countries such as the U.S.A. and Australia have preferred rockbolting. There is increasing interest in extending the rockbolting method in coal mines. The application of rockbolting techniques in an industry which traditionally has not applied such techniques, has required the development of a systematic design approach. This design approach uses extensive monitoring, to asses the viability of the support system in differing conditions. Currently at a number of new and existing mine developments in the U.K., rockbolting is being successfully applied. Although, inevitably some localised geotechnical problems have been encountered and have needed to be taken into account. The effect of faulting on roadway conditions is discussed in this paper and a design approach has been applied using a numerical analysis method, namely the Finite Element Method. The results presented in the paper serve as a useful guide to roadway support designers, and in particular the role played by different bolts in a range of conditions.

Jan 1, 1992

By Chris Mark

Perhaps the most significant development in coal mine ground control during the last century was the introduction of roof bolting during the late 1940's and 1950's. From an engineering standpoint, roof bolts are inherently more effective than the wood timbers they replaced. Roof bolts promised to dramatically reduce the number of roof fall accidents, which then claimed hundreds of lives each year, and they were initially hailed as "one of the great social advances of our time." Roof bolting also emerged at a time of rapid technologic transformation of the coal industry, and greatly accelerated the transition to trackless, rubber-tired face haulage. The U.S. Bureau of Mines quickly became the new roof support's strongest advocate. Some state agencies and miners were skeptical at first, but nearly everyone was soon won over. Case histories were reported showing that roof falls could be largely eliminated while productivity increased dramatically. Little wonder that, in the words of one contemporary observer, "roof bolting has been adopted more rapidly than any other new technology in the history of coal mine mechanization." Yet by the end of the 1950's, it was clear that roof fall fatality incidence rates had actually increased. It would be another decade before the superior ground support provided by roof bolts would clearly save lives, The story of how roof bolting was implemented by the mining industry, but took so long to live up to its promise, is a fascinating example of the interaction between economics, technology, regulation, and science. It still has important lessons for today.

Jan 1, 2002

By Ryan Garvey

A numerical investigation is made into unstable failures of coal pillars (i.e. coal bumps) using the finite difference software FLAC3D. A static energy balance is first derived to calculate the excess energy released as a consequence of unstable failure in rock. Two- and three-dimensional mining layouts are then assessed on their bump-potential based on the magnitudes of excess energy released during simulated pillar failures. A three dimensional pillar model is developed to represent tributary area loading of an infinite room-and-pillar layout. Pillar strength and brittleness characteristics are calibrated using a Mohr-Coulomb strain-softening constitutive law to simulate width-to-height ratio coal pillars ranging from 1:1 to 5:1. Width-to-height ratio pillars 1:1 to 3:1 release large magnitudes of excess energy as the pillars fail, representing massive collapse of room-and-pillar layouts. The larger pillars maintain their residual strength during failure; however significant excess energy is still released during temporary reductions in pillar strength. A two-dimensional model is then constructed of a gate road pillar failing due to elastic rebound of the surrounding rock mass. Soft loading conditions initiate unstable failure for all pillar widths, while the total magnitudes of excess energy increase with the size of pillar being modeled. The results from these tests indicate that excess energy may be used as a direct assessment of the bump potential of simulated mine layouts.

Jan 1, 2013

By Kazem Oraee, Mehran Gholincjad, Navid Hosseini

"Chain coal pillars are pans of the structure of longwall mining system that play a significant role in the stability of the entries. With mechanization and developments in the various aspects of the method, higher efficiency in optimization of the design of chain coal pillars seems appropriate. In this paper the three main methods of chain pillar design, namely the empirical analytical and numerical methods arc compared. Real data from the Tabaslran coal mines have been used in order to make the comparison process reliable. It is concluded that the most apparent advantage of the empirical method is the reliability of the results while the use of numerical methods enjoys the advantage of flexibility. On the other hand the analytical methods are complex unless simplifying assumptions arc made that can substantially decrease the accuracy of result which is thought to be the main advantage of the design method. A new method is therefore introduced here that combines all of the three presently used methods and by doing so the new method has the advantages of the three while minimizing complexities and inaccuracies associated with the use of the individual methods.INTRODUCTIONLongwall mining is a high production method that can use mechanization to its full extent. Its initial development can be traced to 17th century European collieries but it was not until the second half of the 20th century with the development of self advancing support systems that the method gained popularity in the USA (Oraec. 2001). During the last decade, the production of longwall faces has increased significantly (Peng. 2006). The ability for mechanization along with good safety condition is the main reasons for such development. In the longwall mining method a good design for panel and entries on both sides, are two essential parameters. In this method, the thickness of overburden (depth of mine) nom1ally ranges from 60 to 20 m (197 to 2.7 9 ft) (Hartman, 2000) and with increasing mine depth designing for stabilizing the entries on both sides of the panel become more difficult. Thus, for safety and stability the size of chain pillar must increase. This causes the overall coal recovery to decrease and increase mining costs per ton. As such wide pillars hinder the air flow and hence ventilation costs increases too. Therefore with accurate identification of loading conditions and stress analysis. pillar that are a minimum size and sufficient safety factor are carefully designed."

Jan 1, 2010

By Michael Kelly

Current research in longwall mining in CSIRO Exploration & Mining is focused within five major projects and several minor projects. The major projects are: 1 3D Aspects of Longwall Geomechanics. This was reported to the conference last year and a final report will be available by mid-2001. 2 Mine Gas Control. This just completed project centred on Dartbrook Colliery which has a longwall gas make of more than 8 cubic metres per second. 3 Rapid Roadway Development This includes the construction of an autonomous conveying and bolting module (ACBM) that sits between the miner and haulage system. 4 Top Coal Caving In conjunction with the YanKuang group in China, CSIRO and the University of NSW are conducting a prefeasibility study of the Top Coal Caving method in Australian conditions. 5 Longwall Automation. In partnership with the Cooperative Research Centre for Mining Technology and Equipment (CMTE), the CSIRO has conducted a scoping study on this issue and will commence an initial three-year demonstration project in July this year. This paper describes these protects in more detail with particular focus on the last three in the above list.

Jan 1, 2001

By Gregory Hinshaw

Underground mine bolting machines have evolved since inception in the 1940's due to the need for increased safety and productivity. However, major design innovations historically came from changes in the mining plan and the mine environment. During the last ten years, productivity needs have outpaced the evolution of existing designs. J. H. Fletcher & Co. has responded with a commitment to research and development which has fostered several new designs. The most recent machine built is a walk through crawler frame powering four drilling units simultaneously with semiautomatic computer control using two operators. This machine utilizes technology to create a safer yet more productive roofbolter for continuous mining sections utilizing place changing methods.

Jan 1, 1998

By Takashi Sasaoka, Pinyo Meechumna, Hiroshi Takamoto, Pipat Laowattanabandit, Akihiro Hamanaka, Kikuo Matsui, Hideki Shimada

"The EGAT Mae Moh coal mine is an open-cut coal mine in Thailand that produces about 16 million tons of lignite annually to generate 2,400 mw of electricity. The surface mine pit covers is 4 by 7 km (2 by 4 mi) with mining depths ranging up to 260 m (853 ft). A large pit slope is formed with the progression of the mining operation. However, massive slides in the pit slope often occur due to weak planes, such as faults and bedding, and the weak mechanical properties of the rocks. Hence, a 200-300 m (656-984 ft) boundaries of rock block including coal seams is left in front of faults in order to prevent slides and maintain the stability of the pit slope. As a result, there are significant coal reserves beneath the abandoned area along the pit slope.The focus of this paper is on the applicability and design of the highwall mining for recovering much of the coal left along the pit slope.INTRODUCTIONThe EGAT Mae Moh Mine is located about 630 km (186 mi) north of Bangkok, Thailand (see Figure 1). It is the largest coal mine in Thailand and produces about 16 million tons of lignite annually from open-cut mining (70 % of the total coal produced in Thailand). The coal is used to generate 2,400 mw of electricity at the Mae Moh power plant, which is situated near the mining area. The mine pit covers an area of 4 by 7 km (2 by 4 mi) at varied depths up to 260 m (583 ft) as shown in Figure 2. As the mining operation progresses, the pit becomes to be deeper and deeper. In the year 2035, the bottom of the pit is expected to reach depths of 500-600 m and the open-cut mining operation will be finished. The possibility of an underground mining operation is being investigated.A large pit slope is formed with the progression of open-cut mining. However, massive slides often occur in the pit slope along weak planes including faults and bedding planes due to the weak nature of the rock. As a result, 200 to 300 m (656 to 984 ft) boundaries of rock including coal seams are left in place in front of faults to prevent slides and to maintain the stability of pit slope. Moreover, the dip of the slope is less than that of the planned design. As a result, there significant coal reserves abandoned along the pit slope."

Jan 1, 2010

By Maynard O. Serbousek

The mechanics of load transfer of fully-grouted roof bolts in coal mines has been investigated in laboratory and analytical studies. The purpose of this research is to increase the understanding and better interpret data from pull tests which are routinely performed in the field. Laboratory work includes variation of bolt length, hole diameter and grout type in pull tests. Four-foot bolts were tested in holes of 1- and 1-3/8-inch diameters. Both polyester resins and inorganic grouts were used as the anchorage medium. The bolts were strain gauged at six locations to observe the rate of load transfer from the bolt to the rock mass when a force was applied at the bolt end using standard Jack pull testing procedures and equipment. Analytical studies using closed form solutions and finite-element techniques were compared to experimental results. The models are for the elastic regime only but do include slip elements. A detailed analysis of the load transfer mechanisms from the bolts through the grout to the rock mass is presented.

Jan 1, 1984

By Kot F. von Unrug

One of the major difficulties in the proper characterization of rocks surrounding excavations is the lack of data. The existing method for strength determination requires core drilling for sample collection, which, when performed from the surface is costly, and when performed underground, in addition to its cost, interferes with the mine operations. I-landling samples tested in the laboratory is troublesome and also influences the obtained results. Over several years. the author has been interested in developing a method of in situ strength determination that could rapidly generate strength data at low cost without a negative effect on mining activities. The recently developed borehole penetrometer is an improved version of the initial design ( 3 inches in diameter), which was used mainly for strength determination of coal pillars. The new penetrometer has been designed to work in 1.5 inch diameter holes. Such holes can be drilled at low cost with either hand held drilling machines or roof bolters. eliminating limitations of the previous system and opening the possibility of broad application. Strength testing of roof rock around longwall pillars is an example of an obvious benefit when designing secondary roof support. In the paper are given the principles of work of the apparatus and examples of the obtained strength data.

Jan 1, 1998

By André Zingano

This paper analyses possible causes for floor heaving in room-and-pillar coal mining. The coal mines are in the southern part of Brazil, where the Barro Branco Coal Seam varies in depth from 20m to 400m, and a very thick volcanic formation overlies part of the sedimentary basin. The erosion of part of the volcanic formation causes this large range of overburden thickness, which formed large V-type valleys. The mine in study is located near the slope of one of these valleys. The mine inclined shaft is at the lower overburden thickness area of the valley and the mining is developing toward the thicker overburden area. The floor heave occurred in the crosscuts, which are parallel to the slope valley direction. Numerical modeling was applied to study the stress distribution around the openings; and fieldwork on the floor heaved entries was carried out. The geometry of mining (pillar and openings width) also was analyzed. The results showed that the very weak rock and the high horizontal stress were the causes of floor heave. As the mining gets near the valley slope, the stress distribution around the crosscuts changes considerably. In addition, the stress distribution changes as the mining goes far from the crosscut. Keywords: floor failure, room and pillar, finite element model

Jan 1, 2002