Search Documents

By Hideki Shimada

In underground coal mines, grouting method is employed in order to reinforce the floor and to control the movement of groundwater into the roadway. However, the seepage and the reinforcement behavior of the grouting material into the floor are not clearly understood. Therefore, grouting is today normally based on empirical relationships and on the experience of the grouting personnel. To assist grouting projects, it must be acknowledged that many of the flow and the hardening processes occurring during grouting so far defy mathematically analysis. From this point of view. this paper discusses the behavior of grouting material, when it is injected into the roadway floor, by means of 3-D Eulerian-Lagragian seepage analysis. Moreover, the effectiveness of reinforcement grouting on the mechanical properties of slaking-prone mine tunnel floor are studied by means of several laboratory tests. Keywords: Mine tunnel floor, Grout, Seepage, Reinforcement

Jan 1, 2002

By Richard C. Repsher

The U.S. Bureau of Mines has developed a method and device designed to detect lose rock material in underground mines. The technology is designed to be an aid to mine workers in detecting hazardous roof conditions in underground mines which can complement or replace the traditional roof sounding techniques where the miner relies on experience to determine whether rock conditions are sound. The leading cause of accidents and fatalities in underground mines is falls of lose rock pieces or rock slabs from the mine roof. The device is an electronic roof sounding device that acoustically determines the integrity of mine rock. In previous research the Bureau of Mines found that loose rock, when impacted, vibrates at a much lower frequency than intact rock material. A major problem in determining rock stability using this technique has been the repeatability of the matt signal. This difficulty baa been greatly reduced in the current design by measuring the power spectra contained in two separate frequency bands of the signal produced by striking the rock in question. The ratio of the energy contained in each band is computed. This process minimizes any striking force differences, producing accurate, repeatable results for solid rock as well as loose, drummy material. The prototype has been successfully- tested in a variety of underground environments including coal, uranium, molybdenum, silver and salt. The technology has been investigated by the U.S. Mine Health and Safety Administration and the Department of Energy for use in detecting detached tunnel lining areas in nuclear repositories. The paper will discuss the technique, applicable results, and future applications.

Jan 1, 1990

By Francis Kendorski

A longwall coal mine in Appalachia about 1,500 ft deep encountered a fault while developing a new longwall panel. The fault extended from mining depth to the surface near a secondary road and drainage. The fault was located inside the anticipated angle of draw within the mined panel and gob. The fault extended vertically out and up, away from the panel, caved zone, and gob at nearly the angle of draw: the fault very nearly following the angle of draw. It was initially thought that "fault reactivation" could possibly occur. Fault reactivation is the phenomenon of having mining subsidence localized along a fault leading to a "reactivation" of the fault and shearing and displacement along the fault. Such fault reactivation would disrupt and deform the fault plane beyond the normal angle of influence of the subsidence trough, and may provide a conduit for any ground and surface waters to reach the mine. We contacted all operators of longwall mines in Appalachia to determine if any Appalachian longwall mines had ever experienced fault reactivation, and teamed that none had experienced the phenomenon. After studies of possible water intrusion quantities and rates based upon in-fault pump tests, which indicated that water intrusion rates should be manageable, and the prior experience that faults in this particular area were usually barriers to water flow, mining proceeded with caution and monitoring. Mining was successful with no noticeable increase in water inflow rates, and no measurable off-setting of the fault exposure on the surface. It can be concluded that the fault did not reactivate due to its relationship to the mining sequence.

Jan 1, 2003

By Peter Zhang

Shield recovery in a longwall move is normally conducted from tailgate to headgate. However, if the face is wide and the immediate roof is weak, difficult conditions with considerable roof sag, excessive shield load, and local roof falls could occur as the shield recovery proceeds to the middle of the face, causing delays in shield recovery. The situation could be aggravated when a pre-driven longwall recovery room is employed. Alternatively, a bi-directional approach for shield recovery, i.e. shield recovery starting from the middle of the face towards both tailgate and headgate, can alleviate the roof sag significantly by quickly withdrawing the shields towards the lower abutment pressure zones at the headgate and tailgate sides. In this case, the bi-directional shield recovery approach was used in a longwall move for a 1450 ft wide face under weak roof conditions. Shields were successfully withdrawn within five days without experiencing significant roof sag. The time-dependent roof-to-floor convergence, shield pressure, and roof conditions were monitored during shield recovery. 3-D finite element modeling was conducted prior to longwall move to evaluate the difference between a uni-directional and a bi-directional shield recovery during a longwall face move. Vertical stress, yield zone in and around the recovery room, load on the shields, and convergence at the center of the shield canopy were obtained from computer modeling, and compared with the data from field monitoring. Finally, the advantages of the bi-directional shield recovery are discussed.

Jan 1, 2007

By Axel Preusse

Due to a political decision, German hard coal mining will come to an end in the year 2018. By then, there will have been more than 150 years of industrial grade mining activities. Located in the western part of Germany is one of the most densely populated areas of Europe. Multiple coal seams have embossed the earth?s surface up to 20 meters (21.87 yards), as mining has subsided. The aftercare of hard coal mining will consist of three tasks: groundwater management, polder management, and groundwater treatment. The Ewigkeitslasten (cost in perpetuity) at the current groundwater level has been determined in the past. The actual cash value is calculated to be about 12.4 billion euros (approximately 16.5 billion dollars). The cost of groundwater management is directly related to the groundwater level. Rising groundwater levels will reduce the cost of pumping water. Known effects of rising groundwater are uplift of the surface, emission of methane gas at the surface, higher risk of cave-ins, and contamination of drinking water horizons. Each of those processes produces cost in order to prevent negative consequences (e.g., uncontrolled methane emissions) or to handle reparations (e.g., damages caused by surface uplifts). In the long run, it is the goal to minimize the Ewigkeitslast. As a first step, all cost-generating processes are specified, and a cost type based characterization is performed. The objective of this case study is to identify key parameters to determine the quality of a cost-generating process (proportional cost, fixed amount cost). Afterwards, it is intended to specify the quantitative impacts of each parameter and to set up an optimization model to minimize the overall cost. The quantitatively specified parameters will form the base out of which the optimization model is created.

Jan 1, 2013

By Pengfei Wang, Guorui Feng

With increase of cover depth, dynamic incidents, such as large gateroad convergences and coal bursts, are frequently encountered when mining deep longwall panels. It would be more adverse due to large inclination of the coal bed. Because of the shearer and armored face conveyor (AFC) sliding downhill, toppling of shields, disconnection of AFC to the stage loader are related to it. Tangshan coal mine is a typical deep, inclined coal mine situated in the east of China. The split-level longwall panel layout is being adopted for mitigating problems above, where tailgate entries of longwall panels are driven below gob edge and along the floor, while headgate entries are driven along the roof. Wire mesh and steel sets have been used empirically for support for tailgates for about a decade, which reduces the tunneling speed. In view of this fact, the paper serves to investigate the proper adjustment of the tailgate locations and to analyze the resulting stress and yield conditions according to support strategy. First, field measurements and observations were carried out. Stress data distributed within surrounding rock mass were obtained, especially within the roof since the roof consists of only a coal sheet with a thickness of 2–4 m. Roof pressure of the tailgate represents the pressure at the gob edge since it is below the gob edge. The convergence data were also collected. Numerical modelling using FLAC3D™ was conducted and validated by side abutment stress data. The double-yield constitutive model was used to simulate the gob. The finalized tailgate layout and design were determined through comparison of three scenarios. The research in this paper can help engineers choose the proper tailgate layout and support strategies for coal mines that are going to adopt a split-level longwall panel layout for mining deep, inclined longwall panels.

Jan 1, 2018

By L. A. Sandbak, Yan Xing

"The purpose of this study is to evaluate the rock mass stability around the tunnels by three-dimensional (3-D) numerical modeling. Complex geological and tunnel features have been included in the model using the software package 3DEC™. Based on the available information on stratigraphy, geological structures, and mechanical properties of rock masses and discontinuities from the underground mine, 3-D stress analyses were performed on various cases with different K0 (lateral stress ratio) values, constitutive models, as well as support systems. Relations between these factors and the distributions of stress, displacement, and failure zones around the tunnels were obtained and discussed. Finally, comparisons between the field deformation measurements and numerical simulations are used as validations for the simulations, helping to determine the appropriate K0 value and material constitutive models for the underground mine.INTRODUCTIONThe case study site is an underground mine in the USA with a monthly ore production between 20,000 and 30,000 tons. The regional geology of the mine is structurally and stratigraphically complex. Rocks in the area include carbonaceous mudstone and limestone, tuffaceous mudstone and limestone, polylithic megaclastic debris flows, fine-grained debris flows and basalts, all part of the Cambrian-Ordovician Comus formation and related dikes. Both the mineralization and faults have general orientations striking N-S to NW-SE with high dip angles. The ore body in the mine has an incline of about 25---45 degrees located in relatively low quality rock; hence, cut-and-fill mining has been used.This underground mine has two vertical shafts used for ventilation, ore hoisting, and for personnel and material transportation. Development drifts were designed and driven to extract and transport the ore, as shown in Figure I. Bolts, mesh, and shotcrete have been applied in this mine for ground control. In order to reach various locations, the tunnel system is designed with different heading directions and inclines, which will be described in detail later. The area selected for modeling is a cubic region including all the tunnels inside the black square (Figure 1)."

Jan 1, 2016

By Anthony Iannacchionc, Jessica Benner, Harold Miller, Megan Witkowski

"Longwall bituminous coal mining has been practiced in Pennsylvania since the 1970""s. Hundreds of longwall panels have been mined during the last 40 years but only 24 have actually undermined Pennsylvania's Interstate Highway System. The impact to interstate highways are summarized in this paper and the factors that influence the magnitude of these impacts are examined.INTRODUCTIONOver the last 30 years, interstate highways in Pennsylvania have been undermined by portions of 21 bituminous coal mine longwall panels. From 2003 to 2008, three of the panel were extracted by the Emerald Mine and six by the Cumberland Mine both in Greene County and both owned by Alpha Resources. Previous assessments of longwall mining under Pennsylvania’s interstates have identified impacts to the highways but no danger to public safety. In general the magnitude and extent of impacts during the recent undermining of Interstate 79 or 179 appears to be similar as those identified in previous studies. The nine longwall panels are among some of the widest in the U.S. They are supercritical in character with overburdens ranging from greater than 152 m (500 ft) to less than 305 m (1,000 ft).The Pennsylvania Department of Environmental Protection (PA DEP) requested that the University of Pittsburgh summarize observations collected by their staff during the recent undermining of 179. Observations and photographs of impacts to the highway were made by PA DEP staff and entered into reports prepared by California District Mining Office (COMO) staff and statements written into the Bituminous Underground Mining Information System (BUMIS) database. In addition to the observations by the PA DEP, the Pennsylvania Department of Transportation (PennDOT) conducted a series of detailed land surveys along portions of the highway undermined from 2003 to 2008. To characterize the subsidence basin fanned by longwall mining. PennDOT information has been analyzed by another research group within the university (Guticrre7, et al., 20 I 0)."

Jan 1, 2010

By Srisharan Shreedharan, Gang Huang, Hongqing Song, Sijing Cai, Pinnaduwa H. S. W. Kulatilake

"Subsidence prediction due to ore extraction and backfilling during open stoping operations for an underground iron mine in China is reported in this paper. Geologic complexities including faults and interfaces between different lithologies, and the stoping and backfilling sequence adopted from the mine plans are incorporated in building a 3-D discontinuum numerical model. The stoping was simulated in two vertically stacked horizontal layers (Fig. 6), with a total of 16 stopes. Large displacements of up to 50 cm were predicted by the model along the roof of the stopes, and a maximum surface subsidence of 22.5 cm was predicted by the model . Backfilling was found to control subsequent deformation and subsidence. The extraction of the upper orebody led to relatively higher deformations in extracting the lower orebody. Finally, the predicted subsidences at all locations along a subsidence profile on the surface are shown. INTRODUCTIONThe Luohe iron (pyrite) mine, located in Hefei city, Anhui, is an underground mine in China, being mined through the open stoping and backfilling method. The orebody lies at a depth of about 400 m and has an average thickness of 250 m (Magang Steel Company, 2012a). Discovered in the 1960s, the location has a reserve estimate of 300 million tonnes, which have been mined since 2007. The orebody has been divided by the mining company into an east and a west section to facilitate planning for ore extraction.Figure 1 shows the surface above the underground mine, which is seen to contain many human settlements including villages, pastures and other infrastructure. These locations are sensitive in that they need to be protected from potential adversities due to the underground mining, such as surface subsidence. While it may be near impossible to completely eliminate the subsidence due to ore extraction, operations such as backfilling have been adopted by the mine in an effort to substantially reduce it. Hence, this paper focuses on describing the stability of stopes in the mine and estimates future subsidence in a part of the mining region through numerical modeling."

Jan 1, 2016

By Yajie Wang

High horizontal stress and its adverse effects on longwall gate entries have been witnessed in many US coal mines for the past years. It can cause cutter roofs and leads to roof falls either in the headgate or tailgate entries depending on the relative orientation of the panel to the maximum principal horizontal stress. Underground observations have shown that if the maximum principal horizontal stress is perpendicular to the panel entries, the roof is in the worst condition and if the maximum principal horizontal stress is parallel to the entries, the entry is in the best condition. However, little has been done about the high horizontal stress effects on panel entries subject to different orientations of high horizontal stress. In order to design a longwall panel and control the roof effectively, the redistribution and concentration of high horizontal stress field must be fully understood. Using 3-D finite element analysis, this paper presents the high horizontal stress redistribution and concentration for a retreat longwall face with different orientations of high horizontal stress. Based on the results, possible roof failures for different orientations of high horizontal stress are analyzed. A panel design criterion is recommended.

Jan 1, 1996

By Takashi Sasaoka

Indonesia is the second largest coal exporter to Japan, accounting for about 30 M tons annually. They produced about 150 M tons in 2005, over 99% of which being from open-cut mines [1]. However, the conditions of surface mining are becoming worse each year: the stripping ratio is increasing, approaching the economic ratio and the infrastructure for coal transportation from inland mining areas is insufficient for such intense mining operations. To meet the demand for coal in Indonesia and the rest of the world, underground mines have to be developed. At present, there are only five small underground mines, three of which are old and the other two have only recently begun mining operations [2]. However, severe ground control problems have been occurring regularly, roof falls in particular. At a new mine developed from the highwall, a large bolted roof fall occurred at the heading face, killing two miners. Unfortunately, mining engineers and/or miners in this mine do not have a lot of experiences, expertise and know-how concerning the operations of underground coal mines. Since 2001, Japan has started a ?five-year plan for coal technology transfer? to fill Japan?s moral obligation as the largest coal importer in the world. The research team for this accident was organized and the on-site investigation was conducted in order to find the cause of this accident and make the solution. This paper describes the roof fall accident at the mine, discusses its causes and mechanism and suggests the introduction of some techniques for improving the current support system considering the strata and stress conditions by means of field observation and finite element modeling.

Jan 1, 2007

By D. G. Lynch, M. R. Martin, R. J. Coutts

"Broadmeadow Mine is an underground longwall mine located in Central Queensland, Australia. The mine introduced a top coal caving (TCC) longwall face in 2013 but since then has experienced severe convergence events at the start of each panel after 60–70m of retreat, resulting in equipment damage and the longwall almost becoming iron bound. A significant geotechnical monitoring effort during LW10 and LW11 to characterise the caving mechanics and operational changes during LW11 were successful in mitigating the risk posed by these initial convergence events. This paper describes the geotechnical monitoring programme undertaken during LW11, the operational methods used to mitigate these initial convergence events, and the contribution to these events of the TCC technique.A thick sandstone unit close to the extraction roof was likely the cause of the convergence events at the start of each longwall panel. However, stress change monitoring cells, surface extensometers, an inclinometer, and the blockage of holes designed for pre-conditioning using hydraulic fracturing indicated that the convergence events were not caused by the sudden collapse of sandstone bridging across the goaf. Rather, they were caused by the propping action of strong units within the overburden strata. Equipment design modifications were made to allow the longwall to remain operational during the convergence events and an operational strategy was implemented to mitigate convergence in LW11. The initial convergence event was successfully negotiated, and Broadmeadow went on to be the highest producing longwall for CY16 in Australia.INTRODUCTIONBroadmeadow Mine is an underground longwall mine located in Central Queensland, Australia, owned and operated by BHP Mitsubishi Alliance (BMA). The mine is a punch longwall mine using open cut pit access provided by Goonyella/Riverside Mine. Broadmeadow commenced longwall operations in 2005 using a conventional high reach longwall, but later changed to the top coal caving (TCC) method of extraction. Broadmeadow extracts the easterly dipping 5.5–7.5m-thick Goonyella Middle Seam in ranging in depth from 90m to 330m. The coal is washed and blended at the adjacent Goonyella/Riverside open cut mine to produce a premium coking coal product for export."

Jan 1, 2018

By Don Kay

A two year study into the effects of coal mining induced subsidence on cliff lines was undertaken by the Department of Mineral Resources with the support of a grant under the National Energy Research, Development and Demonstration Program. A new monitoring technique, using an Electronic Distance Meter and acrylic reflectors attached to the cliffs, provided safety for the surveyors and extensive and accurate three dimensional displacement data on the movement of the cliffs as they were being undermined. The study report included many graphs showing the measured vertical and horizontal displacements, differential subsidence, tilts and strains and included analysis of these movements with various parameters, such as, seam thickness, depth of cover and distances between the reflectors, longwall face and the edge of the chain pillar. Some of these graphs are presented in this paper and could be used, with caution, to predict subsidence movements around other cliff lines, after allowing for differences in geology and mining layout. A mechanism is suggested as an explanation for the observed high horizontal movements around the cliff lines. Sixteen percent of the overall lengths of cliffs that were undermined during the monitoring study fell and the contributions of various factors that appeared to influence the cliff falls are discussed. It is concluded that no single factor dominated as the major cause of the cliff falls and, often, many factors combined to cause cliff face instability.

Jan 1, 1992

By Kazem Orace, Navid Hosseini, Mehran Gholinejad

"Selection of the optimum support system for underground openings such as tunnels is a complex process. In this paper a new approach, based on a combination of the Analytical Hierarchy Process (AHP) the Technique for Order Preference by Similarity to Ideal Solution (TOPSIS) and the Preference Ranking Organization METHod for Enrichment Evaluations (PROMETHEE), is introduced. For this purpose, the selection process is assumed to be a multi criteria decision-making problem. First different support systems using FLAC3D numerical code, based on technical safety and stability parameters of the tunnel are specified. Then taking economic and performance parameters as the decision criteria by using the combination of Al-IP, TOPSIS, and PROMETHEE the optimum support system is selected. As a real mine case study this approach is used in the main access entry to the C, coal scam of Tabas collieries. Results clearly demonstrate that the proposed support system selection method is more advantageous than other alternatives.INTROD CTIONGenerally, the support system for a tunnel is selected primarily with the aid of design engineers experience. In other words personal judgment instead of intellectual and scientific criteria is mostly the main basis (Oracc. 2005). However since various support systems can be applied in any particular situation, accurate selection of the optimum support method depends on the integration of many technical, economical and performance parameters, and also on the analysis of the intensity of influence by each of the criteria.In this paper an applicable approach for se lection of tunnel support systems based on Multi Attribute Decision Making (MADM) techniques including: Al IP (Orace et al.. 2009a; Saaty, 1980), TOPSIS (Hwang and Yoon, 1981: Yoon and Hwang, 1995), and PROMETHEE (Brans and Vincke. 1985; Brans and Mareschal. 1992) is introduced. As a field study, this approach was applied to tunnel C1 as one of the main entries in the Tabas coal mine which is the major collieries in the central pan of Iran (Hosseini, 2008).Due to the coal seam conditions coal is mined by mechanized longwall mining (Hosseini 2008). This method requires the 58 excavation of several entries some of which will be used for many years and even for the entire life of the mine (Peng, 2006). Therefore the selection of the support system in these entries is·very important in mining design."

Jan 1, 2010

By Gift Makusha

Total extraction mining of coal is being undertaken on a small scale by Anglo Coal South Africa. Longwall mining has been done in the group at New Denmark colliery since the 80s and recently the company started experimenting with pillar mining at Goedehoop colliery. Total extraction mining methods result in caving of the overburden strata that is often accompanied by displacement of air causing wind blasts. The windblasts can cause injuries to underground mining personnel, damage to mining equipment, and ventilation disruptions. Some incidents of windblast damage and injuries have been recorded at both New Denmark and Goedehoop Colliery that prompted mine management to experiment with the goaf warning device, an instrument developed by CSIR mining technology to give early warning of impending god. The initial version of the Goafwarn was originally developed to operate as a stand-alone unit, with LED lights mounted on the device that would flash if the unit was triggered'. That set up would be effective in small working areas where the flashing lights are visible to all workers. This requirement is more difficult to satisfy in longwall application of the unit where mining activities are spread over large linear distances of up to 250 m and the flashing lights would not be visible to all workers in the longwall face. It was also found that the single unit had limitations in distinguishing between man made vibrations and cracking in rockmass leading to an unacceptably high incidence of false alarms. The case studies describe the experiments that were carried out to ameliorate the two issues mentioned above through networking more than one unit. This was achieved through the development of radio communication from the warning devices to a central control (Trollex Data Acquisition Unit) from which the alarms are issued once the prescribed triggers are satisfied. The operating system was made up of 4 Goafwarn units installed 30 m apart with 2 in the tailgate and other 2 in the main gate. The alarm state was defined where 3 or more units were triggered simultaneously. The concept was applied successfully in real time during longwall mining, and management procedures have been developed to achieve safety through the system including switching off the shearer, and flicking the lights to warn people.

Jan 1, 2005

By J. A. Nemcik

Although floor failure at longwall faces has been traditionally associated with a soft floor, in many csses floor buckling has been observed just ahead of the longwall supports, despite the floor being a competent rock The floor failure is associated with the presence of weak bedding planes in the floor and the movement of strata towards the goaf opening. This paper presents the principles of the floor failure based on numerical modelling and field observations and outlines the practical approach to estimate the risks involved with floor failure.

Jan 1, 1995

By Peter Zhang

"Room-and-pillar mining with pillar recovery has historically been associated with more than 25% of all ground-fall fatalities in the underground coal mines of the United States. The risk of ground falls during pillar recovery increases in multiple-seam mining conditions. The hazards associated with pillar recovery in multiple-seam mining include roof cutters, roof falls, rib rolls, coal outbursts, and floor heave. When pillar recovery is planned in multiple seams, it is critical to properly design the mining sequence and panel layout to minimize potential seam interaction. This paper addresses geotechnical considerations for concurrent pillar recovery in two coal seams with 70 ft of interburden under about 1,000 ft of depth of cover.The study finds that, for interburden thickness of 70 ft, the multiple seam mining influence zone in the lower seam is directly under the barrier pillar within about 100 ft from the gob edge of the upper seam. The peak stress in the interburden transfers down at an angle of approximately 20° away from the gob, and the entries and crosscuts in the influence zone are subjected to elevated stress during development and retreat. The study also suggests that, for full pillar recovery in close distance multiple seam scenarios, it is optimal to superimpose the gobs in both seams, but it is not necessary to superimpose the pillars. If the entries and / or crosscuts in the lower seam are developed outside the gob line of the upper seam, additional roof and rib support needs to be considered to account for the elevated stress in the multiple seam influence zone. INTRODUCTION Room-and-pillar mining accounted for about 40% of underground coal production in the United States in 2016. Pillar recovery, practiced in about one-third of the room-and-pillar mines, represents about 10% of the coal mined underground, yet it has historically been associated with more than 25% of all ground fall fatalities (Mark, Chase, and Pappas, 2003). In some U.S. coal fields, particularly central Appalachia, many coal mines are operating under geological conditions with multiple coal seams. The risk of ground falls during pillar recovery increases under multiple-seam mining conditions. The hazards of pillar recovery associated with multiple-seam mining include roof cutters, roof falls, rib rolls, coal outbursts, and floor heave (Mark and Tuchman, 2007; NIOSH, 2010b). Pillar retreating creates abutment pressure, not only in the currently mined seam, but also in the overlying or underlying seams. Multiple-seam interactions become more pronounced as overburden depth increases and interburden thickness decreases. To safely recover the pillars in multiple seams, it is critical to properly plan the mining sequence and panel layout to minimize potential multiple-seam interaction."

Jan 1, 2017

By D. W. Evans

Mine subsidence problems due to coal extraction have occurred in a number of areas throughout the United States. Depending on the local geology, the depth of the mined seam, the type of mining method employed for extraction, and other related factors, subsidence can result in anywhere from slight displacements to a total loss of ground. These conditions can have serious consequences on the health and safety of the people living above the mined areas. A number of methods exist to provide support for the ground overlying mines. All of these methods employ some mechanism for providing additional support to either the roof of the mine or the sides of the pillars. Since failure usually occurs due to overburden stresses which are transmitted to the roof and pillars, these methods employ techniques to counteract stresses induced due to the coal extraction. The applicability of any particular method will depend on the availability of backfill material, the areal extent of the affected area, and of course, the cost. The primary use of coal ash for subsidence control has been as a backfill material for the stabilization of large areas. Large scale backfilling projects for subsidence control have been performed in Rock Springs, Wyoming, Wilkes-Barre and Scranton, Pennsylvania, and in Fairmont, West Virginia. Some of these projects have utilized sand, as well as, coal ash as backfill material. Much of the backfilling work performed in the United States has been done in an effort to control mine subsidence in abandoned mines. South Africa, on the other hand, has used backfilling extensively both for ash disposal and to increase extraction in active mines. The utilization of repetitive fill and mine techniques has resulted in extraction increases of as much as eight percent in shallow mines and as much as twelve percent in deep mines.(1) The coal ash injection system which can be used for backfilling depends largely upon whether the mine voids are dry or submerged. For dry mines, hydraulic or pneumatic conveyance systems can be used, while submerged mines are limited to backfilling by hydraulic methods. The use of coal ash as a backfill material has a number of advantages, such as: 1. Coal ash is available in areas throughout the United States and in many instances is conveniently located near areas requiring backfilling. 2. Coal ash is available in significant quantities since many coals when burned will result in about 15 to 30 percent ash by weight. 3. Coal ash as backfill is, in many instances, the most economical alternative fill material. Due to the costs associated with above ground disposal, power companies will often times give the material away to lower their overall operating expenses. 4. Coal ash is usually pozzolanic in nature, that is, this material results in cementitious bonding within the backfilled matrix of material.

Jan 1, 1982

By Hani S. Mitri

The behaviour of grouted cable bolts used for rock reinforcement as a means of ground control in hard rock mining is investigated. The study utilizes an analytical model which is based on the variational principle to calculate the shear bond stress distribution along the embedded length of cable bolt. In this paper, a comprehensive parametric study which covers both geometric and mechanical design parameters involved is presented. Special emphasis is placed on studying the characteristics of the grout model represented by Winkler springs. This involved varying the maximum shear strength of the grout, its residual strength and the slip occurring between the cable and the borehole wall.

Jan 1, 1990

One of the most important parameters in rock/resin/bolt load transfer mechanism is the surface property of the bolt. Although there are various bolt surface configurations available in the market, very little work is reported on the bolt/resin interface failure mechanism. This paper examines the behaviour of bolt surface roughness under constant normal stiffness conditions which is considered as being a realistic way of evaluating bolt surface roughness. A series of shear tests have been conducted on the flattened bolt surface to study the shear behaviour of bolt/resin interface. Based on the experimental results, a mathematical model has been developed to predict the shear resistance of the bolt/resin interface at various normal stress levels for the bolt types used in the study.

Jan 1, 1999