Search Documents

By V. V. Nazimko

Abandoned coal mines cause subsidence and structural damages. Shallow abandoned mines induce the most severe and harmful damages. In addition, they produce time-dependent subsidence which is difficult to predict. Backfilling of underground cavities with waste materials have been used to prevent the time-dependent subsidence or to mitigate its effect. However, this procedure is expensive. A new drill and blast technique has recently been proposed to prevent surface damage from time¬dependent subsidence over abandoned mines. It utilizes the principle that blasting in the caved rock and roof in the vicinity of a cavity will dilate the ground and create a self-supporting effect owing to increase in the volume. Physical modeling has demonstrated that artificial dilation of caved rock using the drill & blast technique creates positive effects due to the following sequence of events: the dilated rock creates a supporting effect for the suspended rock strata and reduces its span which decelerates 3.4 times the process of caving. The roof span is reduced by the next caved layer, which causes the hole boundaries to incline to each other. This effect converts the process of caving from a developing mode to a reduction mode. Finally, the sinkhole zone assumes a triangular shape with a negative angle of draw 64-700 in contrast to a rectangular shape of the chimney zone for natural caving. Vertical dimension of the triangular zone is 3.87 times of the room height. Final surface subsidence decreases at least 2.09 times; displacement 1.31 times, slope 2 27 times; curvature 3.42 times, horizontal strain 1 21 times in comparison to natural caving of the ground over an abandoned mine.

Jan 1, 1999

By Dennis R. Dolinar

Controlling coal mine roofs subjected to high-horizontal stress conditions has always been difficult and uncertain. Traditional supports such as wooden cribs and posts, concrete donut cribs, and standing supports collapse and fail when the roof and floor move horizontally as mining progresses. The former U.S. Bureau of Mines (USBM) (currently the U.S. Department of Energy (DOE)), in cooperation with Western Fuels-Utah, Incorporated, conducted research to provide an alternative for traditional secondary support systems in a 3-entry gate road system subjected to high horizontal movements. The support system used in several other coal mine operations, consisted of internal high-strength galvanized resin-grouted cable supports. The system virtually eliminates the necessity for external crib, timber, or concrete supports. The support system consisted of 2.4 m (8 ft) full-column resin grouted bolts and 4.8 m (16 ft) long cable supports installed in conjunction with wire mesh and "Monster-Mats." Cable loading and roof deformations were monitored to evaluate the behavior of the immediate and main roofs during first and second panel extractions. Additionally, cable trusses were installed on the longwall headgate to protect the coal conveyance system from roof and pillar falls created by the formation of cutters and gutters. The test results indicated that the designed support system successfully maintained the roof during the extraction of two longwall panels and dramatically reduced the cost of secondary support. This paper describes the theory of high-horizontal roof movements, the advantages of vertical cable supports and cable trusses, and presents the roof and cable measurements made to assess the support performance during longwall retreat mining.

Jan 1, 1996

By Kot F. Unrug

Strength of coal is one of the governing factors in size determination of mine pillars, and therefore affects the percentage of extraction and thus, utilization of reserves. Coal strength is also important from the subsidence control standpoint, where mine pillars with appropriate safety factors should be designed for long term stability. Determination of coal seam strength has been addressed through the extrapolation of the coal strength obtained from a small number of samples on the whole section of the seam. This procedure often gives unreliable results. Presented in this paper is a method of in-situ strength testing of coal, allowing for a realistic determination of seam strength. Results of a field case study dealing with the coal seam, where samples for the laboratory strength tests could not be obtained due to the dense cleat, are presented. However, in these conditions, the in-situ testing was successful. A comparison of both conventional and the in-situ penetrometer method was carried out. It was found that the penetrometer data not only improve the accuracy of strength determination of the entire seam, but also prove to be much more cost effective than the conventional method on a per test basis.

Jan 1, 1995

By Bingjie Huo

"China is a major coal producer and consumer. It is necessary to mine the steeply pitching coal seams due to development of the coal industry to meet the increasing needs for coal. Flexible shield supports mining is a safe and efficient mining method for steeply pitching coal seam that was first applied in HuaiNan mining area in the 1970s. The coal seams are steeply pitching in DaAnShan Colliery, so mining is mainly done by the flexible shield supports method. The roadway lay-out and extraction technology are researched in order to improve the safety, yield and work efficiency in the flexible shield supports working face. Optimization of the flexible shield supports mining method is discussed. The main optimization aspects are as follows: (1) the angle of working face and mining track roadways are increased from 23° to 28°, and (2) the technology and parameters of coal breaking are optimized. Applicable conditions, as well as advantages and disadvantages are also discussed. Finally, a comparison is made of the two different flexible shield supports mining methods, namely ""bench blasting . technology"" and ""piecewise blasting technology"".INTRODUCTIONChina is the largest producer and consumer of coal in the world and relies heavily on coal for energy production. At present, Chinese production is about 42% of the worldwide production, and coal has accounted for 76% of primary energy production. Coal plays a dominant role in the structure of energy production and consumption, which is fuel and an important industrial raw material but it is non-renewable. In recent years, the high inclined seams (35°< angle of coal seam < 45°) and steeply pitching coal seams (angle of coal seam >45°) have drawn increasing attention in the mining sector along with the growth of coal mining. There are two reasons. First, there are abundant reserves of high inclined and steeply pitching coal seams in China, which account for 15- 20% of total reserves (Xie, Dong-hai, 2007). Highly inclined and the steeply pitching coal seams are mined in more than 50% of the western mining provinces such as Sichuan, ChongQing, YunNan, GuiZhou, XinJiang, GanSu, NingXia, etc. As the mining of mineral resources continues west in the 21st century, the study of coal mining in high inclined seams and steeply pitching coal seams will be of great importance. Secondly, better quality coal has become scarcer in the eastern mining areas after years of exploitation, so steeply pitching seam mmmg is growing more prevalent. In short, carrying out research on steeply pitching seam mining technology plays an important role in sustaining the development of the Chinese coal industry."

Jan 1, 2010

By Brian Daniels, James Farroni

"Draw rock (small rock that forms/falls when bolting the roof and/or rib) is the cause of numerous injuries annually. These injuries result in lost work hours and low morale. The report below explains how ""Mine Safe Draw Rock Shields"" (Pans) are used in an underground operation. This report will chronicle the application of these pans in a Southern West Virginia coal mine along with testing data that measures their effectiveness. Since the introduction of these pans in 2002 the amount of reportable accidents relating to draw rock has decreased by 80%. The report below reinforces that perimeter contact is critical to the performance of these pans. In addition the strength of these products at the perimeter will determine their effectiveness. The results of the testing data outlined in this paper, along with the physical records at the study mine, confirm that the use of pans has significantly reduced draw rock falls at this facility.BACKGROUNDSupplemental support is defined as ground control that is used in addition to required support in an underground mine. Some examples of supplemental support are:• Pans• Mesh/Geogrid• Mats• Half Headers• Boards• ChannelA typical roof condition that warrants the use of pans is when loose small rock is dislodged while bolting. If the top is very scaly (loose, thin rock) additional supplemental support can be used in conjunction with pans such as mesh or geogrid (See Figure 1). Pans will provide protection where used and approximately 12 in (250 mm) out from perimeter. This is achieved by contact with a surface which will put scale in tension up to 12 in (250 mm) from perimeter of pan.INTRODUCTIONThe ease of applying a roof support system is critical to effectively operating a deep mine. Figure 2 shows how a pan is installed in conjunction with a roof bolt and bearing plate. The Mine Safety and Health Administration (MSHA) requires that supplemental support cannot decrease the performance of required support. The goal of using all supplemental support is to provide additional safety for the miner which equates to increased productivity.The ability of skin control products to contact a surface is the single most critical characteristic (Figure 3 and Figure 4). If the material does not contact the surface it cannot be effective. Therefore, the flexibility, design and proper installation of the products are critical in determining their effectiveness. Figure 5 shows the proper installation of the roof pan.To reiterate, all skin control must be applied in conjunction with a roof bolt and ASTM approved bearing plate as shown in Figure 4."

Jan 1, 2010

By David Newman

The latest version of the Surface Deformation Prediction Software (SDPS) package is presented through its application to a number of case studies. The package now exploits all the benefits of the Microsoft Windows platform and has a direct interface to CAD software, thus facilitating input and output. Also, the package features advanced calibration routines to handle predictions over specific regions. The case studies presented highlight the features and capabilities of the new package.

Jan 1, 2001

By Shengliyang Yang, Jinghu Yang, Jiachen Wang, Xiaomeng Li

"Safe and efficient mining of extremely inclined thick coal seams less than 20m thick is one of the new challenges in China coal industry. In recent years, the extremely inclined thick coal seams have been encountered in some old mines and western China, and currently the top coal caving longwall mining method has been successfully applied to this kind of coal seams. Accordingly, this paper studies the roof movement and its impact on shield supports of top-coal caving longwall mining in extremely inclined thick coal seams. The structure of main roof before failure was simulated by the fix-ended beam, and provided the solutions for determination of maximum compressive stress of the bottom beam end and maximum tensile stress of the top beam end. The failure mode on the upper end of working face is mainly a combination of compression and shearing, while that for the bottom end is tension and shearing. Roof fracture begins at the upper end of working and propagates downward. The shape of collapsed roof strata can be described as parabolic and divided into three segments from top to bottom, including no filling, uneven filling and densely filling segments. The roof loading conditions of no filling segment is more likely to have dynamic burst impacts.INTRODUCTIONExtremely inclined thick coal seam refers to that the dip angle of coal seam is greater than 45° and the thickness is greater than 3.5m (Wang and Zhang, 2015a; Wang and Zhang, 2015b; Wang, 2005; Xie, Gao, and Shangguan, 2005; Wu, et al., 2014; Deng and Wang, 2014; He, et al., 2015). This type of coal seams can be divided into three categories: 1. The extremely inclined thick coal seam, of which the thickness is less than 5m and the dip angle is less than 60°, is usually mined by fully-mechanized longwall mining method. 2. The extremely inclined thick coal seam, of which the thickness is 5 m-20m, is usually mined by top coal caving longwall method. And 3. When the thickness of extremely inclined thick coal seam is greater than 20m, it is mined by the horizontal section top coal caving longwall method. For example, the average angle ofWudong coal mine in Xinjiang province is 45°, and the thickness is 27m. Wudong coal mine is applying the horizontal section top coal caving longwall mining, producing 3 million tons annually per working face (Figure 1)."

Jan 1, 2016

By Yi Luo

A longwall mining operation went under a tall, self-supporting and free-standing wireless communication transmission tower. In anticipation of that the ground subsidence process might affect the transmission tower, the mining company took a proactive approach to mitigate the expected subsidence influences. The efforts include prediction of surface subsidence process at the location of the tower, assessment of stability, structural integrity and functionality of the tower structures, and design and implementation of mitigation measures. The intension of this paper is to demonstrate the techniques that can be used to assess and mitigate the subsidence effects on tall self-supporting and free standing tower structures.

Jan 1, 2008

By David H. Tang

Massive pillar failures were observed at two underground coal mines. The results of stability analysis using traditional pillar design formulae did not agree with the underground observations. Finite element models were used to analyze the causes and mechanisms of the pillar failures. The results were confirmed by the underground observations. Finally, the improved mine plan for each case was derived to ensure the stability of the underground structure.

Jan 1, 1990

By Dae S. Young

A new probabilistic approach is introduced for slope stability analysis including adverse impact of blasting vibrations. The material strength within a slope area is randomized in this bi-variate joint probability analysis. To be a completely general engineering method, the new probabilistic approach employs the random variable transformation technique; the Hermite model of the Gaussian transformation function, which transforms the experimental histogram of strength values to the standard Gaussian variables. Because bi-normal joint probability is analyzed on the true probability region projected on the Gaussian transformed variable plane, it is an exact solution of slope stability based on the available sample data. Details of the probabilistic approach are given through a case study on an iron ore mine. The case study demonstrated that the probabilistic approach is effective and simple enough to be a routine engineering practice for slope analysis.

Jan 1, 1984

By I. V. Baklashov

Geomechanical conditions of mining operation are determined by varying in time and space mechanical properties and initial state of the rock mass, by geological and technological factors. We define adaptive mining technology as a technology capable of adjusting to changing geomechanical conditions of mining operation. The ongoing research at Moscow State Mining University consisting of laboratory, theoretical, and field investigations aims at the development of theoretical basis and methodology of the system of geomechanical support of adaptive mining technology for the bedded salt deposit in the Urals, mined by room-and-pillar method. This system of geomechanical support is capable of - dynamically assessing mechanical properties and state of the rock mass varying within the panel; - mapping mechanical properties of the rock mass within the panel; - assessing and predicting mechanical condition of load-bearing elements of the rock mass and its changes due to the adjustment of the parameters of mining operation considering the in-situ geomechanical conditions.

Jan 1, 1996

By Keith A. Heasley

In the past, numerous displacement-discontinuity (DD) models of stratified rock masses have been proposed using a homogeneous isotropic elastic overburden. In this paper, it is postulated that a laminated overburden model might be more accurate for describing the displacements and stress in these stratified deposits. In order to investigate the utility of using a laminated overburden in a DD model, the fundamental mathematical basis of the laminated model is presented and graphically compared with the fundamental behavior of homogeneous isotropic elastic overburden and with field data. Specifically, the stresses and displacements surrounding an idealized longwall panel as determined from the laminated overburden model are presented and compared with results from the homogeneous isotropic overburden and with measured abutment stress data. Also, the remote displacements and surface subsidence as calculated by the laminated overburden model are compared with homogeneous isotropic calculations and with measured subsidence data. The results of this investigation show that the laminated overburden is more supple, apt to propagate displacements and stress further, and better able to fit observed data than the classic homogeneous isotropic overburden. Ultimately, it is suggested that the laminated model has the potential to increase the accuracy of displacement and stress calculations for a variety of mining situations.

Jan 1, 1996

By Y. M. Jiang

A users friendly PC Computer Program has been developed to implement a systematic design of the powered support. The required input data are: (1) thickness, RQD, and compressive strength of the immediate roof; (2) mining height; and (3) type, thickness, and tensile strength of the main roof. Several important parameters for support selection under a given geological condition are generated through the implementation of the program, including type of support most favorable for the geologic condition, minimum inclination angle of the legs with respect to the horizontal axis, suitable setting load ratio of the front to rear leg for the 4-leg supports, optimum setting load, and support capacity.

Jan 1, 1989

By Chris Mark

Fully-grouted roof bolts comprise more than 80% of the primary roof supports used in U.S. coal mines. However, nearly 1,500 MSHA reportable, non-injury roof falls occur each year, and most of these are attributable to failure of the roof bolt system. Anchorage failure is one failure mechanism for fully-grouted bolts. As roof deformation works its way upward, the bolts can become heavily loaded near their upper ends, If the applied load exceeds the anchorage, the bolts will simply pull out. Research dating back 30 yrs indicates that this type of anchorage failure is most likely when the roof rock is weak, just where roof support is most critical. In soft shale or coal roof, the small amount of data available in the literature indicates that 20-30 in of resin anchorage may be required to achieve the full capacity of the bolt. In other words, the "full resistance zone" of a 60 in bolt may actually be just 30-40 in. Despite its potential importance, there is no widely accepted anchorage test for fully grouted bolts. Standard pull tests have sometimes been employed, but they provide no information on the anchorage near the top of the bolt. An alternative, first described more than 25 yrs ago in the U.S., is the short-encapsulation pull test (SEPT). With this test, the bolt is installed with only a short (1 ft or less) tube of resin. In recent years variations of this test have become international standards. This paper describes recent studies using short encapsulation pull tests in the U.S. Tests were conducted in the National Institute for Occupational Safety and Health (NIOSH) Safety Research Coal Mine at Bruceton and at underground mines in Pennsylvania and West Virginia. The study found that the SEPT can be used to make a simple evaluation of resin bolt anchorage. Suggested procedures for conducting SEPT are included. The study also confirmed that poor anchorage can be an issue, particularly where the roof rock is very weak. Some simple techniques for improving anchorage, and thereby the effectiveness of fully grouted bolts, are discussed.

Jan 1, 2002

By David Newman

Multiple seam underground coal mining is ubiquitous in Appalachia. Many coal properties have from two to ten or more economically mineable coal seams. Because of the ability to penetrate 600-feet to 1,000-feet or deeper into the mountainside leaving panels of web pillars separated by barrier pillars, highwall mining is a hybrid between surface and underground mining. As a result, many of the ground control problems commonly associated with multiple seam underground mining exist with multiple seam highwall mining. These include: i) superjacent mines, subsidence and caving propagating to overlying seams and ii) mines, pooled water and the potential for inundation resulting from a iii) breakthrough between an active highwall mine and abandoned underground mines in the same or superjacent seams, the presence of overlying or underlying mine workings where iv) pillar columnization in the active mine is not possible, and v) the question of whether to mine ?top-down? or ?bottom-up.? Case histories are presented from southeast Ohio where the Middle Kittanning No. 6 and Lower Kittanning No. 5 seams are successfully highwall mined with 20-feet to 40-feet of largely shale interburden. A highwall miner was caught in a highwall collapse in the Middle Kittanning No. 6 seam when it was overmining auger workings in the Lower Kittanning No. 5 seam. Multiple seam interaction caused by the overmining transferred overburden stress onto the Lower Kittanning No. 5 seam. The overburden concentrated through web pillars initiated auger web pillar failure, resulting in roof collapse and subsidence in the Lower Kittanning No. 5 seam that propagated up to the Middle Kittanning No. 6 seam. A second case history involves multiple seam highwall mining in southeast Kentucky. The A3 Rider, A3, B2, and C1 seams are being highwall mined around abandoned underground mines in the A3 and B2 seams and augering in the A3 Rider. Because of spoil storage constraints for the surface contour mines, the highwall miner follows the active pits in each seam so a standard sequence of ?top-down? or ?bottom-up mining does not exist. The planning and engineering design considerations associated with each case history is presented along with geotechnical information. In the case of the highwall collapse a back analysis is presented of the stability and safety factors for the auger webs, highwall miner web pillars, and barrier pillars.

Jan 1, 2009

By Weidong Pan, Yinchao Yang, Baodong Zuo

Fully mechanized mining technology, with a large cutting height in thick coal seam, has been developed to be large-scale, mechanized, and intelligent. Furthermore, it is also superior to other mining methods because it operates more efficiently and has higher recovery rates of coal resources. Dongpang coal mine (located in north China) is one of the largest coal mining productions in Hebei province. It is significant because it is the first set of coal mines in China to adopt fully mechanized mining technology that has large cutting height potential. When looking at the coal seams of deep mining, specifically in the mine No. 2612 where the working face is 4.5–6.5 m cutting height, the coal walls have low stability due to the way the coal seam fluctuates in a large working face. This paper adopts mechanical analysis, numerical simulation, and field observation research methods to control the rib fall of coal walls in a coal mine. By adopting research methods that analyze the mechanical characteristics of face roof, we are able to conclude the main roof structure of the masonry seam stability criterion in overhead mining with large cutting height. This is done through employing the numerical simulation method, which helped to determine the main factors that influence the rib fall of a coal wall and weighting factor. Through field observations, we discovered the technology method to relieve, control, and mitigate rib falls of coal seam in a coal mine. We also discovered methods that would ensure the smooth mining of the working face of the mine by strengthening the bolting and grouting reinforcement methods used to improve the working face of stope surrounding rock conditions. This paper discusses research results that enrich the stope wall rock control method by expressing how fully mechanized mining technology, with a large cutting height, is meaningful to solve the complex conditions of rock fall caused by thick coal seam.

Jan 1, 2017

By Stankusm John C., Xiaoting Li

"Quantitatively identifying the load on a steel king beam set is a complicated issue in designing the king beam structure at the slope bottom area. From an engineering perspective, understanding the nature and support mechanism of the king beam structure as a standing support is critical in identifying the calculation input parameters for the structure design software. Based on design practices in recent years and successful applications in several slope bottom intersections, the authors present a king beam design methodology, including qualitative analysis, quantitative calculation with a structural design software, and computer Finite Element Analysis (FEA) verification.Especially important is the concept of interaction and the confinement effect between the king beam structure and surrounding rocks, which is essential in designing a proper steel structure in terms of maintaining the roof stability, as well as saving the steel materials and costs of manufacture, labor, and delivery. This paper details the design methodology and applications in several underground slope bottom intersection designs, reaching the goals of improving roof stability and reducing costs.INTRODUCTION AND DESIGN METHODOLOGYCurrently, the load on a square or arch set is typically determined by either past empirical design experiences or known heights of roof falls in current or adjacent mines. These methods work but sometimes are too conservative from an engineering perspective. For example, when designing a king beam structure for an intersection, these methods may lead to a design with extremely large and heavy steel beams, which are not convenient for delivery and installation on-site, not to mention, costly. Therefore, accurately identifying the potential maximum load on the king beam structure is important for designing a safet, effective, and cost-efficient steel structure. Based on past several years’ practices and fundamentals of ground control and structural design engineering, the authors propose a design methodology including the following components:The nature and mechanism of effective roof support (qualitative analysis),Ground reaction curve,Interaction and confinement effect between bolts and steel standing support and surrounding rocks,Factors affecting the load conditions of the king beam set"

Jan 1, 2018

By David P. Conover, Jake Bain, Christopher M. Ross

"Highwall mining of thick (up to 100 ft) steeply dipping (20° or more) coal seams provides many challenges, both geotechnically and operationally because seam dips near or in excess of highwall mining machine capabilities are encountered. Maximizing coal recovery while maintaining highwall stability requires innovative techniques with regard to web and barrier pillar layout, depth of penetration, and choice of mining horizon within the seam. Stability of highwall mining slopes, openings, and pillars are typically analyzed using the ARMPS-HWM program, as well as LAMODEL, UDEC, and Slope-W modeling. Highwall stability can be maintained and highwall mining production optimized by applying design criteria in creative ways, including alternating miner penetration depths and initiating mining of thick seams toward the bottom of the seam. Highwall mining of thick, steeply dipping coal requires careful planning and execution, including close cooperation between geotechnical design engineers, the mining company, and the highwall mining contractor. This paper describes the application of creative design techniques to a specific pit arrangement at the Westmoreland Kemmerer Mine, Kemmerer, Wyoming. Highwall mining was accomplished by UGM ADDCAR Systems, LLC, on a contract basis. INTRODUCTION Highwall mining is a technique for attaining additional coal recovery after the economic strip limit is reached in surface mining. It involves remote deployment of a continuous miner in openings beneath the final highwall, with no personnel entry. Many candidate areas for highwall mining have thick and steeply dipping seams. Mining downdip presents challenges related to the maximum pulling capacity of the machine, traction of the cutting head, and material conveying, all of which limit penetration depth. Maximum penetration is greater for flatter slopes and decreases for slopes nearing the threshold of the maximum machine operating angle. Most highwall mining operations are relatively flat with slight undulations within the seam; therefore, the highwall mining pillar design criteria applies fairly equally to the entire mining area. However, in steeply dipping deposits, design criteria based on higher overburden loads at the far end of the penetration are excessively conservative for the shallower portions of the openings near the highwall."

Jan 1, 2017

By Dave Bigby

Hatworth Colliery, operated by RJB Mining (UK) Ltd, is successfully mining the Deep Soft Seam at a depth of 1000m using single face retreat longwalling. The seam is characterised by a weak roof generally comprising 4 to 6m of well bedded carbonaceous mudstones overlain by weak siltstones. The paper describes the layout and support design strategies which have enabled the colliery to adopt sole support by rock reinforcement techniques for its longwall gateroads. To achieve this success the colliery layout has had to be radically modified to take account of the in-situ horizontal stress field. The layout is also closely controlled by environmental considerations, the seam being one of the gassiest in the UK Economic support by strata reinforcement has been achieved using a combination of rockbolting of the roof and sides installed at the face of the heading, and systematic double birdcage cable bolting installed on drivage and supplemented ahead of the retreating panel. The layout and support strategies have been developed through a combination of detailed underground measurement of support and stress parameters backed up by numerical modelling using FLAC. The FLAC modelling has paid particular attention to careful representation of bedding properties and validation through underground stress measurement.

Jan 1, 1996

By Michael Gauna

In 2010, the number of fatal rib falls in U.S. underground coal mines exceeded fatal roof falls for the first time ever. While recent trends have seen roof fall fatalities reduced by about 62% since the 1990s (from an average of 9.6 per year in the 1990s to 3.6 per year during the last five years), the incidence of rib fall fatalities has remained approximately constant (about 1.5 per year). In addition, injury incidents associated with pillar rib failure have been steady at approximately 100 per year. The persistence of rib fall injuries, underlined by the recent increase in rib fall fatalities, has led to this investigation of the coal rib failure parameters and methods available to mitigate rib failure in U.S. underground coal mines A detailed study of the 21 fatal rib fall incidents that have occurred since 1995 (excluding coal burst incidents) indicates that the two most important risk factors are the mining height and the depth of cover. The depth of cover was 700 ft (213 m) or greater in 81% of the fatalities, and the mining height was at or exceeded 7 ft (2 m) in every instance but one. Other risk factors included multiple seam interactions, rock partings in the seam, and retreat mining. The accident history reveals that joints or slickenside features within the rib increase the hazard. Approximately threequarters of the rib fatality victims were roof bolting machine operators and continuous mining machine operators. This paper includes a brief overview of techniques for rib control; including bolts, standing support, bent steel straps, and rib strapping. The available mining equipment features for installing rib support and protecting operators from rib falls are also discussed. A proactive approach to rib control using available technologies will lower the risk to miners and is an endeavor that must be pursued to reduce rib fall accidents.

Jan 1, 2011