Search Documents

By Ben Mirabile

Over the past three decades, the U.S. coal mining industry has widely used cable supports to supplement traditional primary bolting systems, especially in difficult ground conditions. However, increased mining activity in adverse conditions has underscored the limited effectiveness of the non-tensioned, partially grouted cable supports used to supplement primary bolts. Roof failures in conditions such as corrosive environments, highly laminated strata, low overburden depth and water intrusion have demonstrated that the need for cable technology has reached beyond the traditional non-tensioned, partially-grouted cable tendon. Furthermore, declining market conditions and increased competition for coal customers has demanded that new cable bolt technology be costeffective and readily adaptable to the mining cycle. Jennmar Corporation has developed several cable bolt technologies that can be used as stand-alone solutions or in concert with one another to mitigate adverse conditions. These technologies include rapid tensioning of cable supports, structural surface control and polyurethane injection. The case studies presented in this paper use one or more of these technologies to address adverse mining conditions or special ground control problems.

Jan 1, 2013

By Dwayne C. Kicker

This paper introduces the concept of design theory and methodology as applied to rock mechanics for more innovative and efficient design. This is a "frontier" research area in rock mechanics because although design is a fundamental foundation to all engineering branches, very little attention has been paid to this aspect in mining. In discussing the theoretical premise of design, this paper identifies the principles which form the basis of design activity. Also, from a practical viewpoint, the findings from a series of interviews with mine design engineers are presented. These findings lead to the identification of needs arising from overlooked design methodology in practice.

Jan 1, 1989

By Yongjie Yang

Experimental study on the strength and deformation characteristics of coal under cyclic loading provides guidance for designing coal pillar which is subjected to repeated mining influence during mining. This paper studies the strength, deformation and fatigue process of No.3 coal from Xinhe Colliery under cyclic loading by the MTS815.03 servo-controlled rock mechanics test system. The results indicate that coal is more susceptible to fatigue damage than other hard rocks. Under uniaxial cyclic loading, the fatigue failure ?threshold value? of coal is smaller than 78% of its uniaxial strength, and there is also some fatigue damage when cyclic loading and unloading experiment is carried out below the fatigue failure ?threshold value?. Axial deformation can be divided into three stages: Initial deformation, steady-state deformation and accelerating deformation. Transverse deformation can be divided into two stages: Stable deformation and accelerating deformation. When the transverse deformation begins to increase rapidly and the deformation recovers only slightly upon unloading, it?s a precursor to failure of coal. Under cyclic loading, fatigue failure develops through a process of compaction, strain hardening, and strain softening.

Jan 1, 2006

By John R. Koehler

Available barrier pillar design methods do not adequately account for overburden caving characteristics, the timing and magnitude of associated load transfers, the occurrence of unusual geologic features, or the effects of multiple-panel/multiple-seam mining. To address this problem, the Bureau of Mines, in cooperation with Cyprus Plateau Mining Corporation, conducted a barrier pillar study in a multiple-seam mine setting. Insufficient barrier width resulted in excessive load transfer to an adjacent/underlying section. Consequent entry and pillar deterioration resulted in the section being prematurely abandoned. This paper proposes an approach based on in situ measurements, which includes mine-specific loading conditions in the barrier design process.

Jan 1, 1989

By Stephen P. Signer

This paper presents the results of a case study conducted in a two-entry gateroad in a coal mine where excessive roof deformation and bolt loading resulted in failure of many roof supports. The instruments consisted of 16 fully grouted, strain gaged resin bolts, load cells on both full and partially grouted cable bolts, and vertical deflection multipoint extensometers. These instruments were installed on-cycle to measure loading on bolts in an existing support pattern and to determine if cable bolts could be used to improve roof stability. Results showed significant amounts of movement within the bolted zone. In sonic cases, these movements were enough to load the supports past their ultimate strength. Geology appeared to be a significant factor in localized roof degradation; that is, a very weak rock layer in the immediate roof overlain by a very strong rock layer contributed to the development of shear planes. Only one instrumented bolt had a maximum strain of less than 2,000 microstrain, which was the yield point of the steel. The average maximum strain on all bolts was 20.000 microstrain. However, electrical continuity to many gages was lost, and a pattern was noted that would indicate possible bolt failure. Wire mesh and concrete cans installed as secondary support performed very effectively.

Jan 1, 1998

By Ryan Garvey

A numerical investigation is made into unstable failures of coal pillars (i.e. coal bumps) using the finite difference software FLAC3D. A static energy balance is first derived to calculate the excess energy released as a consequence of unstable failure in rock. Two- and three-dimensional mining layouts are then assessed on their bump-potential based on the magnitudes of excess energy released during simulated pillar failures. A three dimensional pillar model is developed to represent tributary area loading of an infinite room-and-pillar layout. Pillar strength and brittleness characteristics are calibrated using a Mohr-Coulomb strain-softening constitutive law to simulate width-to-height ratio coal pillars ranging from 1:1 to 5:1. Width-to-height ratio pillars 1:1 to 3:1 release large magnitudes of excess energy as the pillars fail, representing massive collapse of room-and-pillar layouts. The larger pillars maintain their residual strength during failure; however significant excess energy is still released during temporary reductions in pillar strength. A two-dimensional model is then constructed of a gate road pillar failing due to elastic rebound of the surrounding rock mass. Soft loading conditions initiate unstable failure for all pillar widths, while the total magnitudes of excess energy increase with the size of pillar being modeled. The results from these tests indicate that excess energy may be used as a direct assessment of the bump potential of simulated mine layouts.

Jan 1, 2013

By Phillip E. Gramlich

Through extensive practical experience and multiple studies, tensioned roof control systems have proven beneficial in difficult mining conditions. Due to increased mining of less desirable seams, tensioned roof control systems have claimed a progressively larger share of the total number of roof bolts installed in the US coal industry. Each tensioned roof control system has its benefits, but also has problems concerning cost, cycle time, stress concentration, load retention, and protrusion into the mine opening. For example, resin-assisted mechanically anchored bolts (also known as resin point anchor bolts) have a fast cycle time and the potential for high tension loading, but the stress from the mechanical shell is concentrated in a small area and can create concerns with certain roof structures (Zhang and Peng, 2001). Resin point anchor bolts can be difficult to fully grout. The cost of resin point anchor bolts can be an issue; a two-piece resin point anchor bolt has a large number of parts (10) and manufacturing steps (9), adding to its higher cost. Tension rebar bolts can achieve high loads and are easier to fully grout but have longer cycle times. In addition, a high percentage of the installed load can ?bleed off? if the resin mixing time or the ?hold time? before tensioning is short-circuited. Tension rebar bolts can be notorious for protruding into the mine opening, creating an obstruction for man and machine (Figure 1), in particular, with reduced mining heights. A new tensioned roof control system has been developed that doesn?t have moving parts, is cost effective, provides fast cycle times, has a low profile, and is simple t install.

Jan 1, 2014

By G. J. Hasenfus

Although theoretical and conceptual knowledge regarding the impact of horizontal stress on underground coal mining excavations have existed since at least the mid-1900s, it wasn?t until the late 1970?s that the theory and practical understanding began to mesh. Since that time, particularly over the last 25 years of this Conference, increased empirical study, as well as advances in measurement technology, computer simulation, and bolt design, has significantly improved our understanding of horizontal stress impact, and provided coal mine operators with tools to reliably predict and manage it. This paper provides a retrospective review of some of the more important horizontal stress-related advancements made during the 25 years of Conference proceedings, particularly those for predicting and controlling horizontal stress impacts within underground coal mines. Relevant and significant CONSOL experiences and studies will be presented in context, with particular attention to horizontal stress considerations for longwall faces and gateroads. The significance of horizontal stress will also be placed in context with respect to local geology and structure, ground support measures, and mining configuration, method, and sequence.

Jan 1, 2006

By Kristineq Pankow

The August 2007 Crandall Canyon mine disaster raised national awareness of mining-induced seismicity (MIS) in Utah as well as general interest in how seismic monitoring might improve mine safety in the region. Unlike the situation in most other mining areas in the U.S., local seismographs in Utah?s Wasatch Plateau (WP) and Book Cliffs (BC) coal fields are an integral part of a modern real-time earthquake information system developed by the University of Utah Seismograph Stations (UUSS) as part of an Advanced National Seismic System. The UUSS earthquake catalog contains a continuous record of MIS at all active mine sites in the WP-BC region since 1978 (more than 18,000 seismic events = M 4.2). We describe characteristics of MIS and current seismic monitoring capabilities in the WP-BC region. We then demonstrate, using MIS from an example Utah coal mine, the ability to refine event locations with estimated absolute errors of ~200 m or less using a combination of (1) a double-difference relocation methodology and (2) ground truth information provided by mine operators. This approach enables sufficient spatial resolution to correlate MIS with mining activities, providing a useful tool to help improve mine safety.

Jan 1, 2008

By P. A. Gray

Artificial ground support has developed into a relined science over the past 20 years. From reactive support systems such as timber props and steel supports, to active systems such as roof bolts and cable anchors, ground support technology has now developed efficient systems that work well in many instances. However this paper demonstrates that there is still a long way to go to develop optimum ground support systems. Some conventional rock bolts and cable anchors emphasise their tensile capacity only, without considering other factors such as their shear strength or shear modulus, or if the support member can transfer all of its support capacity to the surrounding rock. Examples are given of the use of ground anchors with high tensile and shear capacity in underground coal mining as well as examples of slope failures in open pits where the cable bolts have remained intact because they have been unable to transfer their full capacity to the surrounding weak rock mass. For underground coal mines, speed of installation is also of primary concern, but it must also have high tensile and shear capacity both in terms of strength and stiffness. Ground support systems of the future must therefore address these problems. An innovative new rock bait is discussed which goes some way towards solving these problems. This new rock bolt is screwed into the rock and thus has a direct mechanical interlock with the rock. Initial field results show that it has an extremely high anchor capacity and can be fully installed in approximately 30 seconds. It has considerable capacity to improve the productivity of the coal mining industry.

Jan 1, 1992

By Yoginder P. Chugh

Subsidence may be observed above partial extraction shallow room-and-pillar mines where the coal seam(s) is associated with weak and thick claystone in the floor. This paper presents results of subsidence studies at such a mine. During the 26-month study period, a time dependent subsidence causing a maximum vertical movement of 50 mn was observed. After a subsidence rate of 6.0-6.5 m/month for the first two months after development of mine workings, the rate decreased to 0.8-0.9 mm/month after 17 months. However, presumably due to settlement of barrier pillars, it increased therafter to 1.7 mm/month for the next 9 months. Angle of draw, based on zero subsidence, was calculated to be about 29 degrees. Maximum tensile strain and compressive strain values observed were 0.040 pct and 0.039 pct respectively. A hypothesis was fomlated to correlate surface subsidence movements with observed underground movments. The data collected to date fits reasonably well within the formulated hypothesis.

Jan 1, 1989

By Gabriel S. Esterhuizen

A survey of pillar conditions was carried out at 21 operating limestone mines that use the room-and-pillar method. The surveyed pillars were all located in rock that was classified as ?Good? to ?Very Good? using the RMR rock mass classification system. The average pillar width was 14.5m and the width to height ratio varied between 0.53 and 3.52. Pillar conditions were rated using a visual rating system that accounts for the effect of geological structures as well as stress related fracturing. Nine cases of pillar instability were recorded. Pillar instabilities were typically limited to individual pillars or small groups of pillars within an otherwise stable layout. Local geological structures such as inclined discontinuities or weak bedding planes contributed to instability in seven of nine cases that were observed. Elevated pillar stresses contributed to instability in the two remaining cases. All the unstable pillars observed had width-to-height ratios of less than 1.5. It is concluded that pillar instability is most likely to be caused by unfavorable geological structures in pillars with width to height ratios of less than 1.5. Stress related instability such as rib spalling becomes more prevalent when the average pillar stress approaches approximately 20 MPa.

Jan 1, 2006

By David Bigby

In the UK, it is becoming increasingly necessary to open new longwall mining areas above old, abandoned workings. In such cases, strategic and gate roadways must often be driven and maintained across highly stressed areas and pre-existing and sometimes only recently formed subsidence troughs. Ground control at the edges of the subsidence trough can be particularly problematic, with complex combinations of stress and rock conditions being encountered depending upon the precise position in relation to underlying pillar edges. For economic recovery of these reserves, it is essential that rockbolt support is used wherever possible. It is therefore very important to the industry to develop its understanding of ground conditions and support requirements in these areas. This paper describes; ? the historical background to these problems and a series of documented UK case studies from the last 20 years. ? the experiences at UK Coal?s Riccall colliery, where a number of longwall panels were worked at a depth of around 800m, some 65m above previously worked longwalls. Actual experience is compared with pre-mining expectations and model predictions. ? design considerations and experience to date at UK Coal?s Welbeck and Thoresby collieries, which are embarking upon a series of longwalls in the Deep Soft seam, 30-40m above previously worked longwalls. The paper outlines numerical modelling techniques used to optimise such mine layouts within the complex geological and geometric constraints of a mature coalfield. These involve combinations of 2D and 3D finite difference and 3D boundary element models. It also discuss new modelling approaches which will be investigated in forthcoming EU funded research.

Jan 1, 2007

By Axel Preusse

For the last 150 years, subsidence damage to the surface has been an unavoidable phenomenon associated with underground coal mining. In particular, the mechanization of mining methods in multiple seam mining and the concentration of mining activities in densely populated European metropolitan areas (e.g., Ruhr, Upper Silesian industrial region) have led to mining having a very strong influence on the earth?s surface. In both these regions, surface subsidence of more than 20m has been reported up to now in comparison to the original state. Underground coal mining in these regions strongly impairs all kinds of surface use, such as urban and industrial development, infrastructure (roads, waterways, and railways) and pipelines?without restricting the functionality of those objects to a greater extent. Demanding and, in some cases, globally unique engineering solutions have been developed and implemented for this purpose. The previously mentioned mining and industrial regions are still very strongly characterized by the (increasingly declining) coal industry and will remain dependent to a large extent and for an indefinite period on artificial drainage measures because subsidence that has already occurred is irreversible. This paper will primarily discuss the prediction of subsidence that is caused by intensive multiple seam mining and its influence on surface objects (e.g., underground pipelines). However, an approach for predicting ground uplifts due to rising mine water as a consequence of mine closures will also be described.

Jan 1, 2012

By Alan A. Campoli

The mining industry has long been searching for an effective structural application that prevents weathering and falls of loose rock, debris, and sediment. J-Crete is a fiber-reinforced, engineered, cementitious composite rock application that is designed, tested, and successfully utilized as such a material. Laboratory evaluation of J-Crete material properties has shown the final compressive strength to be in excess of 7,300 psi (50.34 MPa), with 24 hour strength in excess of 1,500 psi (10.34 MPa). The flexural tensile strength is in excess of 600 psi (4.1 MPa) and is provided through a unique combination of polyvinyl alcohol (PVA) fibers activated by a proprietary liquid additive that prevents them from clumping and enables even distribution throughout the grout. Tensile bond strength in excess of 350 psi (2.4 MPa) at 28 day cure tightens the strata and holds loose material in place. Practically impervious to gas and liquids, J-Crete protects strata against long-term weathering, does not require screening to be effective, and has proven to be a successful waterproofing material. J-Crete has demonstrated the potential to alleviate coal mine roof cutters in soft, wet clay formations. J-Crete reinforces coal mine ribs by bonding directly to the rib, conforms to the strata, strengthens the rib, and eliminates sloughing due to long-term weathering; stabilizes coal mine entries by bonding directly to the brow and roof, and creates a monolithic shell with double reinforced corners.

Jan 1, 2012

By Da Zhao Gu

An important problem in rock engineering is to control the properties of artificial rock. A compaction technique for casting artificial rock specimens with controlled properties is described, i.e. using a compression-testing machine to compress the mixture. Uniform density is necessary to achieve uniformity of properties of the specimens, and uniform density can be obtained by using the specific pressing method presented. Rebound and borax content are important to the technique and have been studied as well.

Jan 1, 1992

By R. W. Hill

Multiseam mining has been carried out at many collieries in South Africa. It the seams are In close proximity difficult and dangerous mining conditions may arise. In the Witbank area multiseam bord and pillar mining has been carried out, while in Natal where the seams are thinner and of a higher quality, total extraction methods are common. Several combinations of multiseam mining have been carried out. The paper highlights a number of case studies and the strata control problems that can arise.

Jan 1, 1995

By Michael Alber

Pullout tests on resin grouted rock bolts have been executed in coal mines and surface test sites. The goal of this study was to provide some qualitative information about the rock mass quality from mandatory tests with a bit little more effort. Movements of rock bolt head and steel plate at different load levels were analyzed and were found to yield information about the rock mass deformability. The tests were interpreted similar to plate bearing tests and a rock mass compressibility index C was assigned. This index reflects the complex interactions between the rock mass, resin grout and bolt under load. Although further research is necessary it may be concluded that those tests may aid in recognizing geological conditions.

Jan 1, 2003

The applicability of four empirical strength criteria for rock masses, namely, Hoek and Brown, Bieniawski - Yudhbir et al., Rarnamurthy - Arora and Johnston - Sheorey et al. has been tested against the triaxial test data for jointed plaster of Paris of Arora. The following modified Bieniawski criterion shows best agreement with the triaxial test data for jointed plaster of Paris:- where st = axial compressive stress at failure, MPa; s3 = confining pressure, MPa; scm = uniaxial compressive strength of jointed plaster of Paris, MPa; and B = - 3.988 + 9.674 (scm )-0? 185 The modified Bieniawski strength criterion can be used to estimate the strength of a coal pillar, based on a knowledge of stress distribution in it.

Jan 1, 1992

By Michael Gauna

Ground fall injuries and fatalities in United States underground coal mines have shown a diminishing trend. Advances in bolting and standing support systems have led to improved safety in underground coal mines. However, the Crandall Canyon Mine disaster in 2007, in which 9 individuals were fatally injured as a result of a widespread collapse, emphasized that proper mine design is a critical issue that must be addressed. The Mine Safety and Health Administration (MSHA) has instituted technical review procedures structured to facilitate the implementation of safe mine designs in underground coal mines. The technical review process and the typical information required are outlined in this paper. The range of mining situations that lead to a technical review, common design methods submitted for review, and their relevant guidelines and limitations are also discussed. Additionally, the relationship between design criteria and mine site historical experience is discussed.

Jan 1, 2011