Search Documents

By Winton Gale

"The aim of this paper is to summarise the results and conclusions of Australian Coal Association Research Project (ACARP) Report Cl3013 which relate to water inflows into a mine which occur through the overburden above and adjacent to longwall panels. The study assessed available data of inflows into underground coal mines and utilised computer simulation of water flow through fracture networks. The study concluded that flow into mines is typically via an interconnected network of pre-existing and mining induced fractures. The height above the coal seam that mining induced fractures extend is typically related to the width of the panel. However the potential for those fractures to form a connected network which can facilitate flow, is related to the amount of subsidence and the depth of mining. The study compares model simulations with measured data and provides guidelines to estimate the average hydraulic conductivity of the overburden above extracted longwall panels in Australia.INTRODUCTIONWater inflow into coal mines has been a design issue for many years. Guidelines as to the potential for water inflow have been developed in many countries based on local experience and the form of mining being undertaken. In most instances, the guidelines relate to inflows which would endanger underground personnel and operations.In more recent times, water inflow criteria for mines has been widened to include lesser inflows which may not impact on mine safety or operations, but have the potential to reduce water flow within streams and surface aquifers. For the purpose of this paper the larger inflows which are readily measured in a mine or may impact on mining safety are defined as mine inflow and the lesser inflow relating to aquifer water loss as environmental inflow.The water losses referred to are those which enter the mine from the surface or from near surface aquifers.The empirical relationships developed as mine design guidelines or regulations typically relate to high flow (mine inflow) situations and in this paper, these have been reviewed as to their application to environmental inflow. In many cases environmental inflows were unlikely to have been noted or recorded in many mining operations in the past."

Jan 1, 2010

By Lorraine Kent

Comparison of in-situ stress overcore measurement results with those determined from laboratory evaluation of Acoustic Emission (AE) testing on oriented sub-core samples has been carried out for a variety of mining environments. These include UK and German Coal mines at moderate depth, shallow-level South African Coal mines and deep-level South African gold mines. Results show that the `Kaiser Effect' or 'Stress Memory-Damage is readily determinable throughout the brittle deformation process, although particular care is required in interpretation of results during the 'bedding-in' phase of testing and the region associated with unstable crack growth prior to failure. The results suggest that AE provides a useful complimentary method for comparison with existing methods of stress determination. The success of the method can, however, be dependent on both rock type and the likely magnitude of in-situ stress in comparison to the strength of the rock. Keywords: in-situ stress, acoustic emission, Kaiser Effect

Jan 1, 2002

By Brad R. Blair

This paper will review impacts on longwall design and ground stability assessment due to advances in mine automation and sensing technology. Several new approaches to the prediction and monitoring of longwall panel and gateroad stability have recently become mature, and are ready for application in problematic ground control situations. These methods are revealing significant detail regarding deformation and failure mechanics of critical underground structures. Examples of how these technologies have worked successfully will be given, and applications for the use of these tools for cost-effective engineering design and monitoring will be suggested.

Jan 1, 1996

By Vincent A. Scovazzo

"The most significant study on the effects of longwall mining on gas and oil well integrity was completed by a consortium of coal and shale gas industry participants. A field study was conducted in 2013 and 2014 and is referred to by its location on Well Pad NV-35. The experiment site was located at the CONSOL Enlow Fork Mine in Washington County, Pennsylvania.The experiment was completed to verify John T. Boyd Company (BOYD) calculations and studies completed under contract by for the Pennsylvania Department of Environmental Protection Gas Well Pillar Study Update. The findings of the original study were presented by BOYD at the 32nd Conference, while numerical analysis of the Well Pad NV-35 field study was presented by Dr. Su at the 35th Conference.This paper addresses the findings of the experiment and how it confirmed the conclusions of the original study.INTRODUCTIONA field study was conducted in 2013 and 2014 by a consortium of coal and shale gas industry members to test the effects of longwall-induced ground movement on the stability and integrity of wells drilled through a gateroad abutment pillar. The project was initiated to test initial John T. Boyd Company (BOYD) findings of the Gas Well Pillar Study Update (Scovazzo and Moran, 2014), completed for Pennsylvania Department of Environmental Protection, Bureau of Oil and Gas Management (PDEP). Background and initial findings on this project were presented at the 32nd Conference (Scovazzo and Moran, 2012). The field work and numerical analysis were spearheaded by CONSOL Energy, Inc. (CONSOL) with participation by Chevron, EQT, Noble Energy, Range Resources, Marcellus Shale Coalition, and the Pennsylvania Coal Alliance.Dr. Wen H. Su of CONSOL was the leader of the field experiment with input from the participants. Dr. Su also completed numerical analysis of the results and model casing deformation. Analytical results were presented by Dr. Su at the 35th Conference (Su, 2017)."

Jan 1, 2018

By Jon Bowler

Daw Mill Colliery, UK Coal, near Coventry in England, mines the Warwickshire Thick Seam at 800 m/2500 ft depth using longwall retreat with gateroads supported by rockbolts. Over the last eight years the mine has worked longer and wider panels with extraction heights of over 5 m. Recently the mine has experienced high deformation conditions principally from the rib sides resulting in operational issues and production delays. Investigation of rib deformation was undertaken using new inspection and measurement techniques, including systematic laser surveying, and improved rib support consumables were developed and introduced. A new rib trussing system using textile webbing has proved very successful.. A rib support management system was also developed and introduced for face retreat. This allowed rib support to be more effectively managed both for production and safety. For the current developments, new 28-mm-diameter roof and rib bolt systems have been introduced and rib bolt length has been increased to 3 m, with the aim of achieving gateroad stability over the life of the panel. Significant reductions in roof and rib deformation have been confirmed by the latest monitoring results. These ground control innovations are allowing Daw Mill?s potential to be realised. Production from 302?s face in 2008 set new UK and European records. However the support enhancement process continues and further innovations are planned.

Jan 1, 2009

By Gamal Rashed

This research is divided into two parts: the first part of this research focuses on understanding coal mine bump mechanisms, and the second part focuses on mitigating the violent failure associated with a bump. Many researchers believe that the coal bumps happen because of sudden loss of constraint between pillar/ roof and pillar/floor or the hammering effect due to the breaking of thick, massive strata above the coal seam, creating a sudden impact load on the pillars and causing them to bump. However, very little work has been done to explore and understand the consequences of these proposed mechanisms for coal bumps. In the first part of this research, computer simulation of coal specimen behavior have been used to explore two issues: 1) How would an instantaneous loss of constraint or a small sudden impact load cause violent failure? 2) How does the strength of the coal specimen control coal mine bumps? Eliminating or reducing the violent failure is the main objective of the second part of this research. The coal specimen needs to be softened either in the rib zone or the core zone and then its mode of failure studied to see whether it is violent or not. Instantaneous loss of constraint and the hammering effect are associated with sudden release of elastic energy, increase in the kinetic energy, and very rapid transient vertical stresses of the coal specimen. These are three of the major proposed mechanisms for bumps. The potential for violent failure increases with increasing the unconfined compressive strength, UCS, of the coal specimen. Failure of the rib zone is not the main factor for the violent failure of a coal specimen. The energy stored in the core zone is the key factor for the violent failure.

Jan 1, 2013

By Alan J. Zeni

Drainage of water from abandoned underground mines has become important in recent years because of safety concerns when mining near abandoned works or reentering abandoned mines for further development. Seepage from inundated mines causes environmental damage and may threaten homes and communities. Where topography permits, horizontal drilling can provide a quick and cost effective method for solving trapped water problems. The mechanics of the horizontal drilling operation as applied to water drainage are discussed in this paper.

Jan 1, 1990

By Jimenez Leon, Christopher Newman, Boede Gabriel, Zacharias Agioutantis

"Ground movements due to longwall mining operations have the potential to damage the hydrological balance within as well as outside the mine permit area in the form of increased surface ponding and changes to hydrogeological properties. Recently, the Office of Surface Mining, Reclamation and Enforcement has completed a public comment period on a newly proposed rule for the protection of streams and groundwater from adverse impacts of surface and underground mining operations (80 FR 44435). With increased community and regulatory focus on mining operations and their potential to adversely affect streams and groundwater, there is now a greater need for better prediction of the possible effects mining has on both surface and sub surface bodies of water.As mining induced stress and strain within the overburden is correlated to changes in the hydrogeological properties of rock and soil, this paper investigates the evaluation of the hydrogeological system within the vicinity of an underground mining operation based on strain VALUES (calculated through a surface deformation prediction model. Through accurate modeling of the pre- and post-mining hydrogeological system, industry personnel can better depict mining induced effects on ground water flows through the overburden material aiding in the optimization underground extraction sequences while maintaining the integrity of surface and subsurface bodies of water.INTRODUCTIONThe utilization of high-recovery underground mining methods, such as longwall or high-extraction room-and-pillar operations, have the potential to cause adverse impacts to both surface and subsurface bodies of water as strata movement and deformations propagate from the mined seam through the overburden to the surface (Peng, 2008).Previous research has indicated that mining induced strains are the most damaging to surface streams (Singh, 1992) as well as greatly affecting the integrity of subsurface bodies of water and groundwater flow conditions (Booth, 1986). On the surface, adverse effects to the stream can occur due to the development of either tensile or compressive strain in the stream bed. The development of tensile cracks along the bedrock allows for a potential loss of stream flow through developed fissures. In fact, water flow in the Cataract River of Australia ceased in 1994 as a result of mining-induced strains from longwall operations in the Bulli seam 430 meters (1320 feet) below the river gorge (McNally and Evans, 2007). On the other hand, the development of compressive strains within the rock layers can cause rupturing or buckling of the stream bed, blocking stream flow and/or diverting flow into the fractures at the base (Iannacchione et al, 2010). While these localized fractures can contribute to the loss of stream flows, given time, damaged streams have the ability to self-heal through the regeneration of near-surface aquifers as well as the sealing of mining-induced fractures with rock debris, gravel, sand, clay or other soil particles carried from upstream sources and deposited in the river bed (Waddington and Kay, 2002)."

Jan 1, 2016

By John H. Perry

Strata III is a full-spectrum roof control system which provides the mine operator the ability to upgrade his roof control in place. The procedure is easily adaptable with current roof bolting techniques. To use the system, the operator starts by installing a special hollow core mechanically anchored roof belt during the roof bolting cycle. This bolt can be upgraded to a fully grouted tensioned rebar bolt by injecting StrataGee G-300, a special polyurethane grout, around the bolt through an injection port in the roof plate. This same bolt can then be used to inject RokLok binders for roof consolidation by pumping the binders through the core of the bolt. This concept in roof control was developed to provide the mine operator a flexible way to maintain roof control in areas which deteriorate over time, or must be kept open for long periods of time. Possible locations of use would be: longwall set-up rooms, recovery rooms, headgates, intersections, and belt entries.

Jan 1, 1987

By E. Bane Kroeger

For many years, researchers around the world have been investigating coal pillar stability. Many have focused on trying to optimize the size of the pillars by examining stable and failed pillars in underground coal mines. For mines that are already in operation or companies that are opening a new mine adjacent to an existing mine where the pillar dimensions and stability can easily be determined, this is the preferred technique. However, when a new mine is planned for an area where there has been relatively little mining, then samples of the coal need to be drilled and tested for strength. Because of the fractured nature of coal, this lab testing is often problematic and may often yield poor results because of the limited size and number of samples that can be obtained from the core. To remedy this problem, research was conducted in the labs at SIUC to determine if improvements could be made when optimizing the size of pillars for underground coal mining in Illinois. Through a greater understanding of the relationship between dimensions and strengths of coal samples tested in the lab, it was hoped the in situ strength of coal pillars could be determined with greater accuracy. This could allow the extraction ratio to be increased and more of the coal resources in Illinois recovered without impacting the safety of the mine workers. Many different agencies around the world have published recommended minimum numbers of samples for strength determination based on the size of the coal samples. For two inch cubes, uniaxial testing of at least seven samples is recommended and this minimum number decreases to four when testing four inch cubes. However, the laboratory testing of coal from two seams thus far has suggested this number should be almost doubled to accurately determine the coal strength. Testing also showed there is a pronounced decrease in the variation in the strength of the samples tested as the dimensions of the sample were increased. From the testing results thus far, it is recommended that a sample size versus strength curve be constructed for every coal seam for Illinois. Creating such a curve will better determine both the minimum number of samples and minimum sample dimensions for that seam or region of a particular scam. A second set of tests were conducted in the laboratory to determine the increase in strength with reduction in height for samples with the same width and length. In Illinois, typical pillar dimensions are 40 to 80 feet (12.2 to 24.4 m) wide and long, with coal thickness varying from about 4 to 9 feet (1.22 to 2.74 m). This provides width/height ratios ranging from 4.5 to 17.5. Coal samples having width/height ratios ranging from 0.5 to 13 have been tested thus far. As with most pillar design formulae, the strength of the Murphysboro coal versus width/height ratio was linear and closely matched shape factors published by other researchers. The laboratory testing thus far has identified three factors that affect the strength of laboratory samples, the number of discontinuities, the angles of critical discontinuities, and the shape of the samples. The factor that probably had the most pronounced effect on the strength of the coal samples was the angle of critical discontinuities. This testing has confirmed that there is still a gap that needs to be bridged between the strength obtained from laboratory testing and the in situ coal strength predicted.

Jan 1, 2004

By D. F. Scott

Seismic tomography, as used in mining, is based on the principle that highly stressed rock will demonstrate relatively higher P-wave velocities than rock under less stress. A decrease or increase in stress over time can be verified by comparing successive tomograms. Personnel at the Spokane Research Center have been investigating the use of seismic tomography to identify stress in remnant ore pillars in deep (greater than 1220 m) underground mines. In this process, three-dimensional seismic surveys are conducted in a pillar between mine levels. A sledgehammer is used to generate P-waves, which are recorded by geophones connected to a stacking signal seismograph capable of collecting and storing the P-wave data. Travel times are input into a spreadsheet, and apparent velocities are then generated and merged into imaging software. Mine workings are superimposed over apparent P-wave velocity contours to generate a final tomographic image. Results of a seismic tomographic survey at the Sunshine Mine, Kellogg, ID, indicate that low- velocity areas (low stress) are associated with mine workings and high-velocity areas (higher stress) are associated with areas where no mining has taken place. A high stress gradient was identified in an area where ground failed. From this tomographic survey, as well as four earlier surveys at other deep underground mines, a method was developed to identify relative stress in remnant ore pillars. This information is useful in making decisions about miner safety when mining such ore pillars.

Jan 1, 1996

By Michael Bayerl

The HILTI OneStep rockbolt was implemented for roadway development in German deep coal mines in 2004. The development by HILTI Company is based on a technical joint venture with RAG Deutsche Steinkohle AG. The technical development of a One-Step bolting system was required for weak strata conditions at the roadway development face. Standard resin bolting has reached the limit of performance when boreholes are squeezed and cannot be filled with capsules. In some cases the heading face is brittle and requires additional support for installation of the bolts and a person working immediately next to the borehole. The Hilti One-Step system allows automated and safe processing at the heading front and provides the key technique to avoid these problems.

Jan 1, 2009

By Andre Zingano

The coal seam strength and the failure criteria that represent the behavior of the coal seam are very important for mine section and pillar design. Additionally, mine section and pillar design take into account roof and floor layers, which form the roof-pillar-floor system. Therefore, underground ground control design begins, most importantly, with rock mass characterization. Another issue is the distribution or behavior of the coal seam strength for the whole mine area. Sometimes, the coal seam strength is assumed to be the same for an entire area, but this is not true because the coal seam is heterogenic and anisotropic, and also the coal strength is affected by faults and spacing between fractures. The objective of this paper is to demonstrate the use of the methodology for geomechanics characterization to determine the strength for the Bonito coal seam, and discuss the coal seam strength distribution around the entire mine area. The intact coal strength was determined by laboratory tests that were completed during the last 17 years, including triaxial and uniaxial strength tests. It was noted that there is a strong correlation between all laboratory strength tests with 90% confidence interval. The explanation for this coal seam strength variation is the presence of the discontinuities and their variation in quantity and quality at each location in the mine area, because the coal seam rock classification and its behavior will be affected by the quantity and quality of fractures.

Jan 1, 2014

Previously, a variety of risk rating systems were used on different mines. However, these were mostly site specific and geology based systems. The purpose of developing a uniform rating system, to be used on all Anglo Coal open cast mines, is to provide an unbiased, standard and quantifiable assessment of the risk from highwall and lowwall failures. This takes into account relative differences in the importance of hazards, as experienced on each mine as a result of different combinations of geotechnical factors and mining conditions. The system is based on critical geotechnical and other parameters that have been identified by mining personnel and rock engineers. The primary advantage of this risk rating system is that all open cast mines in Anglo Coal use an almost identical system, which enables the user to compare their risk to the risk at neighbouring mines and/or other open cast mines. The system can be adjusted to meet local, mine specific requirements. The implementation of this new system (a computer program that automatically calculates the risk) has been made as practical and easy to use as possible. Therefore, this tool can be used by personnel from other mining disciplines not directly related to rock engineering.

Jan 1, 2004

By K. F. Unrug

A new testing technique for the determination of the rock strength from portable rock tester is proposed. It is a quick and economical method that can determine the rock strength with reasonable accuracy in different conditions. This method is based on the application of portable rock tester working at the principle of forcing steel ball into the rock surface. The correlation between laboratory measured compressive and/or tensile strength and rack tester reading has been determined in terms of the three-controlling parameters: (1). diameter of indentation &'the testing sample, (2). diameter of indentation-on the reference bar, (3). Brine11 hardness number of reference bar.

Jan 1, 1990

By William Bookshar

The development of increasingly more sophisticated and powerful retreat longwall equipment has led to ever wider and longer panels. To maximize gateroad development efficiency, provide for effective face recovery, andlor reduce ventilation pressures, entries are cut across longwall panels in advance of longwall retreat mining. These entries must be supported to prevent falls of immediate roof in advance of the face. Recently, cut through entries and predriven recovery room entries have been supported with various combinations of roof bolts and passive support. The cost and relative success of these support systems has varied considerably. Eighty-Four Mining Company, Fosroc, and Sub-Technical have developed and implemented an efficient, yielding, multiple component, cement crib to support longwall panel cut through entries and pre-driven recovery rooms. The cutable crib consists of an inexpensive flyash cement pillar poured in a bag, within a temporary metal form. The form is moved to a subsequent cutable crib location after the initial hardening of the flyash pillar. The remaining entry height between the mine roof and the top of the flyash cement pillar is filled with a specially designed bag filled with Fosroc's Tekset cement formulation. The diameter of the pillar and thickness of the Tekset bag are designed to accommodate the anticipated front abutment loading and entry convergence.

Jan 1, 1998

By Yoginder P. Chugh

Subsidence may be observed above partial extraction shallow room-and-pillar mines where the coal seam(s) is associated with weak and thick claystone in the floor. This paper presents results of subsidence studies at such a mine. During the 26-month study period, a time dependent subsidence causing a maximum vertical movement of 50 mn was observed. After a subsidence rate of 6.0-6.5 m/month for the first two months after development of mine workings, the rate decreased to 0.8-0.9 mm/month after 17 months. However, presumably due to settlement of barrier pillars, it increased therafter to 1.7 mm/month for the next 9 months. Angle of draw, based on zero subsidence, was calculated to be about 29 degrees. Maximum tensile strain and compressive strain values observed were 0.040 pct and 0.039 pct respectively. A hypothesis was fomlated to correlate surface subsidence movements with observed underground movments. The data collected to date fits reasonably well within the formulated hypothesis.

Jan 1, 1989

By S. P. Singh

Destress blasting is commonly used in the mines to minimize the occurrence of rockbursts. The fracturing created by destressing in the vicinity of the face reduces the stress concentration by pushing the zone of high stress deeper into the rock mass. But the destressing practice by blasting may be devastating near the faults or other sensitive high stress zones. To avoid severe rockbursts in such situations, the application of chemical destressing has been proposed in this paper. A laboratory investigation was conducted on the rocks in the Sudbury basin to examine the change in the material properties with an aim of assessing the feasibility of destressing by chemical means. The favourable change observed in the rock properties led to the suggestion that the injection of surfactants in boreholes would enhance fracture propagation similar to what is currently done by blasting but in a safer, inexpensive and non-violent manner. The current destressing practices in Ontario mines have also been reviewed in this paper.

Jan 1, 1987

By Vincent A. Scovazzo

Many accepted and useful methods have been developed and used for pillar design. Each method has its own particular strengths and weaknesses. Three methods addressed in this paper are; empirical, analytical, and numerical. Each of these methods have their place in pillar design. Analytical methods result in close approximation of the ideal pillar (most economical, stable, or yielding) and are suitable for use in final mine design and in analyzing existing problems. BOYD uses the analytical method to develop site specific mine pillars design equations. An analytical method, one of many developed by BOYD, is presented here and is based on the procedure used by Wilson (1) and others in development of their empirical equations.

Jan 1, 1995

By Joel Bradley, Kot Unrug, Kyle Perry, Mark Klimek

"A West Kentucky mine operation in No. 11 seam, encountered floor heave, due to the localized increase of the thickness in the fireclay mine floor. Floor heave has overridden seals installed in two mined out panels. The third seal’s location was planned for isolating that area from the Mains. A plan of support has been developed to prevent repetition of the floor heave and related problems outby the seals. The applied ground control measures were successful. An attempt of a 3D numerical modeling was made, that it would match the observed behavior of the mine floor and could be used as a design tool in similar conditions. In the paper described are sequence of events, a mitigation ground control system applied, and the first stage of numerical modeling.IntroductionWest Kentucky coal mine operation in the No. 11 seam has approached an area where the fireclay floor thickness increases to about 5 ft. Delayed floor heave has been observed. In the first sealed area (Panel KK), floor heave has overridden the seals and has begun to progress outby. This could not be allowed at the new seal location PP described in this paper because such override would affect the mains. Previously numbers of standing support systems were used, but their effectiveness was not satisfactory as is illustrated in Figure 1, Figure 2, and Figure 3. Therefore, with sealing of the next area approaching, mine management was looking for a better solution that would eliminate the problem. In that stage, our team looked closely at the geology and strength of roof and floor, as well as the characteristics of ground failure around the seal at the first site. The technical literature has been searched as well Haramy et al. 1986 Hsiung and Peng 1987, Peng 2008, Santos & Bieniawski 1987. This led to the identification of factors responsible for the ground failure. It has been determined that increased fireclay thickness from typically less than 2 ft to about 5 ft, when compared to the previously mined parts of reserve, and the strong limestone strata just above the immediate roof composed of 2 ft of black shale, created conditions of failure. It appeared that, when pillars were punching into the mine floor, the strong roof did not break but was bending, exerting high pressure on outby pillars, causing rib failures and closure. This is a similar mechanism to a strong roof affecting longwall shields. The remedial action planned was additional support."

Jan 1, 2015