Search Documents

By John C. Stankus

The success of cable bolts for mine ground control have been well documented in papers presented at this conference too numerous to reference. Cable bolts have proven effective over the years mainly utilized in the form of supplemental support. Some limited work has been conducted on the use of cable bolts as primary support This work has been mainly confined to the West and the bolts utilized were of a non- tensioned type MSHA requirements for primary support have been that the bolt system he tensioned or if non-tensioned, then fully encapsulated with resin. Many operators are now interested in using cable bolts as primary support Further, despite the enormous success of cable bolts, there have been questions raised about the longevity and corrosion characteristics of the cable itself particularly for long tern applications. To improve the corrosion characteristics of cable bolts, galvanized cable has been used for some applications However. although improving the corrosion resistance of cable, galvanized cable for mine ground control does not provide complete protection under certain types of situations and mine environments. Realizing a need for a cable bolt that can be used for primary support and provides consistent installed tension, complete corrosion protection, and a fast installation, Keystone Mining Services. LLC (KMS), an affiliate of Jennmar Corporation, has developed the INSTáL CableOx system. This paper will detail the development and specifics of this system including two underground case studies

Jan 1, 2000

By Frank E. Chase

During the past quarter century, coal mine geologists have evolved from providing a qualitative description of drill core and coal reserves into quantitative geotechnical specialists who bridge the gap between geology and engineering. In the late 1970?s and early 1980?s, hazard prediction mapping was in its infancy. At best, hazard maps identified rudimentary structures and conditions such as stream valley locations, sandstone/shale transition zones, and lineaments. A ?technical disconnect? had existed between geologists and mining engineers as each profession operated largely independent of each other. Engineers did not readily integrate geology and geologic conditions, with the exception of coal thickness, into mine planning. Geologists were relied upon for reserve estimates and did not participate in mine planning or design. The employment and market slump of the 1980?s and 1990?s combined with mining more challenging reserves mandated that this gap be bridged and forced geologists to learn to speak more ?numerically? to engineers so they could be understood. The purpose of this paper is to describe the procedures and thought processes used by coal mine geologists when determining various mineability and reserve extraction feasibility issues. The paper will also address underground geologic hazard mapping and prediction techniques. To achieve these objectives, the opinions and experiences of leading coal mine geologists, geotechnical and strata control specialists across the United States were solicited.

Jan 1, 2006

By J. R. M. Hill

The U.S. Bureau of Mines is involved in research to improve geological sensing (or geo-sensing) techniques. This paper presents results from field trials of two research projects concerned with new technologies for geosensing. The goal of the first project was to develop a "smart" roof bolter drill so that it could probe into roof rock to evaluate rock conditions. The goal of the second project was to modify an existing mine-wide monitoring system in a continuous mining operation so that the system could interface with geotechnical instruments to provide near real-time geosensing. Integration of this mine-wide monitoring system with the smart roof drill to collect, reduce, and analyze geotechnical data and the potential applications of the resulting technology in mining, are described.

Jan 1, 1992

By Naj Aziz

The shear behaviour of reinforced rock joints is investigated for the bolt-grout-rock interaction and for failure mechanism. The effectiveness of the bolt application under lateral and axial loading conditions within surrounding materials is investigated in different medium strength. Double shearing testing of bolts were studied in concrete blocks of 20, 40, 50 and 100 MPa strengths, subjected to different pretension loads of 0, 5, 10, 20, 50 and 80 KN respectively. The experimental study was complemented with three-dimensional numerical analysis. Parameters examined include: shear resistance, shear displacement, induced strains and stresses during bolt bending process and its ultimate failure across the sheared joint planes. The conclusions drawn from the study were; the level of bolt resistance to shearing was influenced by the bolt profile configuration, the strength of the rock or medium influenced the level of load generated on the bolt, and the increase in bolt pretension has contributed to the increased shearing load of the bolted medium.

Jan 1, 2007

By Peter Fischer

Reducing mining costs has become such an important factor in the German coal industry that operators are forced to work only those areas where production costs can be kept low. These areas will normally be located close to the mine shafts because they are easily accessible. Even the shaft pillar is now being considered as part of the winning zone. Before working coal in shaft pillar zones it is essential to assess the impact this will have on the shaft lining. There is a huge difference between sliding and strata-anchored shaft systems. However, if the overburden comprises lightweight soil both types of shaft will have a tendency to protrude from the surrounding ground. This paper presents the geomechanical reasons underlying this reaction and the methods used for predicting and measuring it.

Jan 1, 2007

By Kevin M. Connor, O&apos

An example application is presented in which Time Domain Reflectometry (TDR) was utilized to monitor roof strata movements during pillar extraction in a potash mine. The study was initiated when Western Ag-Minerals decided to implement secondary mining of pillars in order to extend the life of their Nash Draw Mine. A prototype operation was conducted in one mine panel to assess mining equipment and procedures, and to determine if ground control problems would develop. An instrumentation array was installed by personnel from New Mexico Tech and Western Ag to monitor strata movements, changes in pillar stress and surface subsidence, and these data are being analyzed by the Bureau of Mines. This paper is limited to a discussion of roof-floor convergence and roof strata movement to illustrate the application of TDR to ground control. Plots are presented which demonstrate the capability of distinguishing location, magnitude and mode of rock movement using TDR to interrogate coaxial cables grouted into holes drilled in the roof.

Jan 1, 1990

By Guy Reed, Russell Frith, Kent Mctyer

"Coal pillar design has historically been based on assigning a design factor of safety (FoS) or stability factor (SF) to coal pillars according to their estimated strength and the assumed overburden load acting on them. Acceptable FoS VALUES (have been assigned based on past mining experience, and at least one methodology includes the determination of a statistical link between FoS and probability of failure (PoF).The role of the pillar width-to-height (w/h) ratio has long been established as having a material influence on both the strength of a coal pillar and its potential mode of failure. However, there has been significant professional disagreement on using both FoS and w/h ratio as part of a combined pillar system stability criterion, as compared to using FoS in isolation. The argument is that, as w/h ratio is intrinsic to pillar strength, which, in tum, is intrinsic to FoS, it makes no sense to include w/h ratio twice in the stability assessment. At face value, this logic is sound.However, this paper will argue that there is a valid technical reason to bring w/h ratio into system stability criteria (other than its influence on pillar strength), as it is related to the post-failure stiffness of the pillar, as measured in situ, and its interaction with overburden stiffness.When overburden stiffness is bought into pillar system stability considerations, two issues emerge. The first is the width-to-depth (W/H) ratio of the panel, in particular whether it is sub-critical or super-critical from a surface subsidence perspective. As a minimum, this directly relates to the accuracy of the pillar loading assumption of full tributary area loading. The second relates to a reevaluation of pillar FoS based on whether the pillar is in an elastic or non-elastic (i.e., post-yield) state in its as-designed condition, as relevant to maintaining overburden stiffness at the highest possible level.The significance of the model presented is the potential to maximise both reserve recovery and mining efficiencies without any discernible increase in geotechnical risk, particularly in thick seams and higher depth of cover mining situations. At a time when mining economics are, at best, marginal, removing potentially unnecessary design conservatism without negatively affecting safety is of interest to all mine operators and is an important topic for discussion amongst the geotechnical community."

Jan 1, 2016

By Gang Chen

Conventional methods designate a factor of safety, a deterministic number, to indicate the stability of a mine excavation. However, this deterministic description of excavation stability is frequently insufficient or inaccurate and, sometimes, misleading. Employing the probabilistic analysis to determine the likelihood of mine excavation failures will lead to a better understanding of ground control problems and result in more rigorous designs of the excavations. Based on the theory of probability, two approaches are taken in this study for the probabilistic analysis of excavation stability. The first one utilizes direct integrations for the estimation of failure probabilities of mine excavations. Due to the complexity of the integration, this approach can only be applied to solve relatively simple problems. In order to overcome the limitation of the direct integration method, the second approach employs the first-order second-moment approximation of the failure probabilities for more complex ground control problems. The probabilistic analysis offers a deeper insight into the uncertainty associated with the stability of mine excavations. The study indicates that the distributions of parameter values play a significant role in the mine excavation stability, which can not be disclosed by the conventional methods of stability analysis. Greater dispersiveness of the parameter values will lead to a different probability of failure, although the factor of safety estimated by conventional methods stays the same if the mean values of the parameters are constant. By taking consideration of the probabilistic distributions of the parameters, the probability model can provide more reliable designs of mine excavations.

Jan 1, 1996

Results of direct shear tests on rock discontinuities and triaxial compression tests on intact rocks are presented and - discussed. The main parameters considered area stress functions, angle of internal friction and cohesion variations. Primary objective of this work is to determine relationships that adequately describe the rock behaviour for design of mining excavations, while still maintaining a certain degree of simplicity.

Jan 1, 1987

By Daniel W. H. Su

This paper presents a retrospective assessment of ground control research and its successful application by CONSOL Energy over the past 25 years. Recognizing the need to improve the understanding of coal pillar design mechanics under shallow, medium, and deep covers, an extensive underground coal pillar instrumentation program was initiated in the mid 1980s. Combined with sophisticated numerical modeling technique and laboratory tests, results from this instrumentation program were used to advance the concept of coal pillar design and to demonstrate that numerical modeling can be used to predict in situ coal pillar strength, especially under non-ideal conditions where interface friction and roof and floor deformation are the primary controlling factors. To evaluate the impact of longwall mining, a 10-year subsidence research program was initiated in 1986 that encompassed surface, subsurface, and underground measurements, as well as a sophisticated numerical modeling technique. Results from the research revealed that interface friction and shearing between rock layers within the overburden had a profound effect on surface subsidence development and the resulting strain. Recognizing the impact of horizontal stresses on CONSOL?s mining operations, extensive horizontal stress measurements were conducted using the USBM Borehole Deformation Gage and the CSIRO Mininfrac system in the mid to late 80s. Roof extensometers and CSIRO HI Cells were used to measure roof displacement and roof stress concentration in longwall headgates and tailgates, which resulted in the definition of right-hand and left-hand longwall panels. Pillar design modifications, combined with cable bolt application and innovative standing support installation, were then successfully employed to mitigate horizontal stress impact on the right-hand longwall headgates and left-hand longwall tailgates. An in-house floor bearing capacity test apparatus was fabricated and employed underground to determine mine-specific floor bearing capacities which, along with other geotechnical parameters, were then used in the mine-specific shield design. To promote caving of thick, massive sandstone immediately behind longwall face supports and to improve face conditions, the hydraulic fracturing technique was successfully employed by CONSOL to pre-fracture the sandstone prior to longwall mining. Face monitoring and numerical modeling confirmed the effectiveness of the hydraulic fracturing technique. A roof geology reconnaissance program was initiated by CONSOL in the early 1990s to improve roof control, safety, and production. Information obtained from the reconnaissance program was used successfully to guide mine planning decisions and daily roof support practices.

Jan 1, 2011

By Dave Forrester

Mining subsidence over shallow abandoned coal mine workings is unfortunately not an uncommon experience in the coalfields of North America and there is a significant knowledge and literature base addressing the phenomenon and related issues. From time to time, however, a case history arises which is outside the more routine occurrence. This paper addresses one such case and presents an overview of a subsidence Event above abandoned coal workings, which badly damaged a two-story High School building. The subsidence at the Cape Breton & Victoria Regional School Board (CBVRSB)'s MacDonald High School in Dominion, N.S., Canada on October 30, 2002 led to a detailed investigation. It was concluded that the ground movement and associated building damage had been caused by mining subsidence in underlying old underground coal mine workings of the 1890s, only 150 ft deep at the School. The Event was not isolated and a similar but smaller event happened nearby a few months later. The paper describes the events and summarizes the subsequent investigations and findings. The 17-year old High School building was eventually demolished.

Jan 1, 2004

By Kikuo Matsui

In a difficult economic environment, the coal mines in Japan have been making extensive efforts in order to survive by rationalizing the mining operations. Introduction of a new longwall mining system is one of these efforts to establish the rational production structure. In the high production longwall mining system, gateroads should be developed rapidly and maintained effectively during their lifetime. Strata bolting support system has been employed in the gateroads to raise their stability levels and reduce their maintenance cost. However, excessive gatemad closure caused by longwall mining is still occurring, impeding the passage of equipment, personnel transportation, and ventilation air in the longwall panels. This paper describes the development system of gateroads and proposes a new mining method to control the excessive roadway closure problem.

Jan 1, 1995

By John D. VandeKraats

Yielding rock bolt systems have been developed to provide ground support while accommodating shifting, creeping, or swelling ground movements. The Dywidag Systems, Inc. (DSI) Slip Nut System is one such system. It has been tested in the laboratory and installed and monitored in the interbedded halite and anhydrite at the Waste Isolation Pilot Plant (WIPP) since 1994. The Slip Nut System is installed on a point anchored threaded bar or on a threaded bar coupled to a cable bolt. At a pre-engineered load the nut acts as a die and cuts through the thread on which it rests, thereby reducing the load and coming to rest on the next thread where the process repeats. Two types of laboratory tests were performed using slip nuts on DSI's threaded bars and their Tensionable Cable bolts. Straight pull tests exceeding 0.3m (1 ft.) of displacement were performed on the systems. Also, offset tests were performed on these bolt systems in a test frame designed to simulate WIPP geologic conditions. A room scale test area consisting of 186 threaded bars began in 1994. Select bolts were instrumented to track bolt load. All bolts were tracked through time for operation. Through three complete years since installation over twelve slips, corresponding to approximately 0.15m (6 in.) of ground movement, have been observed in some areas. Since installation strata offset has exceeded 0.08m (3 in.) at a supported clay layer in the roof. No bolt failures have been observed. Slip loads observed underground generally approximate those observed in the lab. To date, the slip nut systems tested and installed have performed as expected.

Jan 1, 1998

By Michael Gauna, Christopher Mark

"Underground coal mining in the U.S. is conducted in numerous regions where previous workings exist above and/or below an actively mined seam. Miners know that overlying or underlying fully extracted coal areas, also known as gob regions, can result in abutment stresses that affect the active mining. If there was no full extraction, and the past mining consists entirely of intact pillars, the stresses on the active seam are usually minimal. However, experience has shown that in some situations there has been sufficient yielding in overlying or underlying pillar systems to cause stress transfer to the adjoining larger pillars or barriers, which in turn, transfer significant stresses onto the workings of the active seam. In other words, the overlying or underlying pillar system behaves as a ""pseudo gob."" The presence of a pseudo gob is often unexpected, and the consequences can be severe. This paper presents several case histories, summarized briefly below, that illustrate pseudo gob phenomenon:• Pillar rib degradation at a West Virginia mine at 1100-foot (335 m) depth that contributed to a rib roll fatality.• Pillar rib deterioration at a Western Kentucky mine at 570-foot (175 m) depth that required pillar size adjustment and installation of supplemental bolting.• Roof deterioration at an eastern Kentucky mine at 1300- foot ( 400 m) depth that stopped mine advance and required redirecting the section development.• Coal burst on development at an eastern Kentucky mine at 1700-foot (520 m) depth that had no nearby pillar recovery.• Coal burst on development at a West Virginia mine at the relatively shallow depth of 1100 feet (335 m) that also had no nearby pillar recovery.The paper provides guidance so that when an operation encounters a potential pseudo gob stress interaction the hazard can be mitigated based on an understanding of the mechanism encountered.INTRODUCTIONThe U.S. underground coal mining industry has conducted mining in multiple seam environments, where the active mining has underlying or overlying old workings at varying interburden distances, throughout its history. Often no serious consequences arise from the multiple seam mining. However, sometime mines have been confronted with hazards from underlying or overlying workings that include localized roof and rib failure, pillar system failures through propagating roof falls and floor heave, and also pillar bursts."

Jan 1, 2016

By Gennaro G. Marino

Documented case histories of surface ground movements from mine subsidence were utilized to help determine when the initial collapse of the overburden occurred above longwall panels. By studying this relationship between initial movement at the surface and the amount of face advance, the least-complex conditions exist for empirically assessing the span capacity of the overburden. The objective of this work was to obtain a better understanding of the overburden response to longwall mining. This knowledge will give a better insight on the long-term effects that different overburden types have on the stability and the subsidence potential of room and pillar mines, as well as, the influence of the overburden on subsidence over longwall panels. Theory on the overburden span capacity was developed and correlated to field observations. Data were used on the overburden lithology, depth, width, and face advance of the panel, and the subsidence conditions that were noted on the surface. The subsidence measured on the surface was used to determine when complete failure in the overburden rock had occurred. According to spans predicted by theory and the subsidence measured in the field, the competent lower units failed at a face advance less than when significant subsidence was observed on the surface. In each case studied, there were competent lower beds; however, the full overburden weight was not sustained to the point of subsidence. The best correlation with the surface movement was found with the most shallow, competent bed. Elastic plate solutions with various support conditions were found to best monitor the surface subsidence of these upper roof units.

Jan 1, 1988

By Andre Vervoort

The roof in coal room and pillar panels is normally stratified and can be thought of as beams or plates supported by the pillar sides in the roadways and by pillar corners in the intersections Underground measurements showed the effect of the face advance on the additional total movement of the roof skin and on the relative movement between various layers in the roof. The latter consists of the opening of bedding planes and of the lateral sliding of layers over one another. Both phenomena increase locally the axial load along full column anchors. Four models have been used to come to a better understanding of the roof behavior: a beam either clamped above the pillar side or laying on the pillar sides and a three-dimensional boundary clement model with and without bedding planes. The shape ref the curvature of the roof deflection is host approached by a clamped beam: the other models overestimate the movement at the sides. The largest roof deflection for a given Young's modulus is estimated by the model incorporating bedding planes. This model estimates that the bed separation occurs close to the face (within the first meter) and within 0.2 m of the sidewalk. In some simulations, openings are even recorded just ahead of the face. Further underground measurements should focus on these findings, as the effectiveness of the support is directly related to the amount of bed separation and sliding, which have occurred prior to the support installation and which still cart occur abler installation.

Jan 1, 2000

By David Conover

The El Boleo Copper Project is currently in the final design stages for development of a 3-MM-tonne/yr underground copper mine located in Baja California, Mexico. The nearly horizontal mineralized zones are amenable to exploitation by conventional mechanized coal mining technology using continuous miners, shuttle cars, and belt haulage. The mine design resembles a typical full-extraction coal mining operation utilizing a sequence of mains, sub-mains and production panels. Due to numerous faults, mining will be conducted as several small adjacent mines accessed through adits from large arroyos cutting through the mine area. Up to four seams may be mined in some areas with a maximum overburden depth of about 250 m. The ore zone is relatively weak and plastic, subject to extensive creep over time. The mine workings will pass through areas of historical shortwall mining panels where the ground has flowed into old entries and gob areas, and then reconsolidated. A small test mine was developed to evaluate mechanical cutting performance, roof-bolt anchorage capacities, roof and pillar stability and caving behavior. In-mine measurements were combined with two- and three-dimensional FLAC models to evaluate alternative development and production pillar designs. The paper will discuss the various factors influencing ground stability at the El Boleo project and the strategies employed in developing a suitable ground control design.

Jan 1, 2009

By Gabriel Esterhuizen

Underground stone mines in the United States make use of the room-and-pillar method of mining. A prerequisite for a safe working environment is that the pillars should adequately support the overburden and the pillar ribs and rooms should remain stable during mining. At present pillar dimensions are either based on experience at neighboring mines or on strength equations that were developed for metal or non-metal mines. This paper presents a pillar design methodology that was developed from a study of pillar performance in operating stone mines. Data were collected that describe the rock mass quality, pillar conditions, mining dimensions and intact rock strength. The results showed that current mining practices have resulted in generally stable pillar layouts with no recent cases of extensive pillar collapses. However, a small number of single failed or failing pillars were observed in otherwise stable layouts. Numerical analyses were used to supplement the observations and develop a pillar strength equation that describes the stable and small number of failed pillars observed. The developed strength equation can be used to design stable pillar layouts provided the factor of safety is greater than 1.8 and the width-to-height ratio of the pillars is greater than 0.8. The paper concludes with guidelines for applying the developed equation and selecting appropriate input parameters.

Jan 1, 2008

By Peter Hatherly

As a discipline, geophysics covers an enormous range of scales and applications - from planetary geophysics through to the monitoring of acoustic emissions of rock samples. Although it is not a core discipline within the mining industry, geophysics has a useful role in providing information on the nature of the rock mass and the way it is responding to the mining process. For coal mining purposes, geophysical studies mainly seek to - delineate boundaries between the coal and the various layers within the surrounding strata - determine the physical properties of the rocks in-si tu, and - monitor the response of the rocks to the mining process Some of these applications may be associated primarily with mine planning, but once a mine is underway, most geophysical results can be used for the purposes of ground control. For example, insights into the nature of a geological fault mapped by a 3D seismic reflection survey will be relevant to determining support requirements while mining through it. In some instances there are parallels in the use of geophysics by the petroleum industry. Seismic reflection and wireline logging techniques have mainly been developed for petroleum exploration where their on-going development continues to provide spin-offs for the coal industry. The 3D seismic survey techniques that we now routinely employ were in their infancy 25 years ago and, almost certainly, the high quality borehole scanning tools that are now available would not have been developed without the need for petroleum well evaluation. Mining has also led to the development of specific techniques. An example is microseismic monitoring for the management of roof conditions during longwalling, and also the prediction of rock and coal bursts. The use and success of this technique have grown greatly over recent years. Another example lies with the use of geophysical wireline logs to predict rock strength and in rock mass classification. Coal seams also provide an unusual geophysical situation in that they form seismic and electromagnetic waveguides. The in-seam seismic and radio imaging methods have been developed to exploit these geological properties. In this paper I address the development and application of geophysical methods such as these with a particular emphasis on their role in ground control. We will see that there have been many developments over the past 25 years but we should also think about the future and how geophysics needs to be developed. From a miner?s perspective, one obvious area of need is in the detection of voids in the vicinity of current mine workings, be they old workings or karsts within nearby carbonate beds.

Jan 1, 2006

By Chris Mark

Perhaps the most significant development in coal mine ground control during the last century was the introduction of roof bolting during the late 1940's and 1950's. From an engineering standpoint, roof bolts are inherently more effective than the wood timbers they replaced. Roof bolts promised to dramatically reduce the number of roof fall accidents, which then claimed hundreds of lives each year, and they were initially hailed as "one of the great social advances of our time." Roof bolting also emerged at a time of rapid technologic transformation of the coal industry, and greatly accelerated the transition to trackless, rubber-tired face haulage. The U.S. Bureau of Mines quickly became the new roof support's strongest advocate. Some state agencies and miners were skeptical at first, but nearly everyone was soon won over. Case histories were reported showing that roof falls could be largely eliminated while productivity increased dramatically. Little wonder that, in the words of one contemporary observer, "roof bolting has been adopted more rapidly than any other new technology in the history of coal mine mechanization." Yet by the end of the 1950's, it was clear that roof fall fatality incidence rates had actually increased. It would be another decade before the superior ground support provided by roof bolts would clearly save lives, The story of how roof bolting was implemented by the mining industry, but took so long to live up to its promise, is a fascinating example of the interaction between economics, technology, regulation, and science. It still has important lessons for today.

Jan 1, 2002