Search Documents

By Jaco J. van Vuuren

Modikwa Platinum Mine, in the Eastern Bushveld of South Africa's Limpopo Province, is a new operation employing a hybrid mining method where mechanised methods are used for the main developments and the narrow, 60cm reef is conventionally stoped using a down-dip conventional mining method. Throughout the mine, the hanging wall immediately above the reef comprises 3 jointed and laminated layers of varying thickness, commonly known as the triplets, below a non-cohesive leuconorite parting plane. At North shaft, using pre-stressed standing support and mechanically anchored rockbolts, it was found difficult and hazardous to hold all three triplets in the hanging wall, however bringing them down caused a significant increase in dilution and therefore cost of mining. A novel solution was conceived whereby two of the triplets are kept up using short, stiff resin anchored rockbolts installed systematically within 0.5 m of the face. This resulted in both safety and productivity benefits. The rockbolts create a stable and safe hanging wall and allow the mine to extract UG2 reef more economically. New drilling equipment, developed locally from available drilling technology, can be operated from a safe position, and in situ tests and measurements are made to confirm effective support. The technology and underlying concepts were successfully tested in a trial stope prior to rolling out the new support system across all the stopes at North Shaft. This has involved an extensive training programme to ensure that the rockbolt system is installed correctly and that the conditions are appropriate for this technology. The paper describes the motivation behind the project, the underlying technology and its application to Modikwa, and the benefits now being realised.

Jan 1, 2004

By Jeffrey K. Whyatt

Estimation of the initial vertical stress carried in a coal seam is an important first step in virtually all methods of evaluating the required size of pillars in coal mines. Such estimates are a trivial exercise in coal fields overlain by gently undulating topography. The LaModel program is easily and routinely applied in such cases to efficiently estimate mining-induced stresses throughout the coal seam. However, application of LaModel to coal mines operating under rugged topography and/or in tectonically disturbed regions is more difficult. LaModel estimates stresses in a twostep process. Topographic and multi-seam mining effects on insitu stresses are estimated in an initial step, and then mininginduced stresses are estimated in an independent second step. A LaModel program function has recently been introduced that decouples these two steps, allowing in-situ stresses to be directly entered from a file rather than calculated. One application of this function is to streamline sensitivity studies by avoiding repeated recalculation of in-situ stress. The function also allows importation of in-situ stress estimates developed by other means. There are no constraints on the imported stress field, which may include significant stress perturbations due to topography, faults, etc. Hence, the range of geologic environments that can be examined by LaModel is significantly increased. This study uses the new decoupling function in an exploration of in-situ stress estimation in mountainous terrain. One option is to use the topographic stress estimation feature included within the LaModel program, and the influence of important parameters in this routine is explored. Another option explored is importation of results from a detailed volume element model. Results of this study suggest that the method used to estimate in-situ stress, and the details of its execution, can have a significant impact for mines in mountainous terrain with strong overburden. More generally, decoupling is an efficient and flexible function that should be considered for most design studies.

Jan 1, 2011

By Gexin Sun

This paper overviews the recent research progress in predicting cutting performance using fracture mechanics principles. It is emphasised that rock fragmentation due to cutting is mainly a process of chip formation resulting from crack initiation and propagation or crack interaction for multi-tool cutting. This process can be simulated by using the well developed fracture mechanics criteria coupled to numerical methods. Fracture toughness is shown to be an important and useful parameter in quantifying cutting performance and in designing cutting tools. The paper concludes with discussions on the dynamic effects involved in rock cutting processes which should be taken into account for optimum cutting efficiency and tool design.

Jan 1, 1992

By Hamid Maleki

A new failure criteria is proposed for assessment of roof stability in underground sedimentary rocks. Unlike other stability assessment techniques, this method is simple and practical, having improved mine safety and productivity in several mines. It is shown that roof movements accelerate to a critical rate prior to actual roof collapse. Critical rates vary between 0.025 inches per day to 0.2 inches per minute depending on rock mass - pillar mechanical properties. Specific critical rates are determined for three rock mass - pillar categories which are common to mining in sedimentary rocks. Time-to-caving varies from one minute to ten days on rock structural controls and type of primary support utilized.

Jan 1, 1990

By Yi Luo

Subsurface strata movements and deformations associated with underground mining activities could cause problems to subsurface structures and water bodies. By incorporating the methods for surface subsidence prediction with the subsidence parameters derived from collected subsurface subsidence data, methods have been proposed for the prediction of final and dynamic subsurface movements and deformations induced by underground longwall mining. Two new' types of strata deformations in the field of subsidence research, vertical and total strains that could he useful in assessing subsidence influences to the subsurface structures and water bodies, have peen introduced.

Jan 1, 2000

By Jamal Hematian

Understanding the behaviour of rocks in a high horizontal stress field, such as that in Australia, is critical when analysing the stability of underground structures. This paper addresses the significance of the post-failure behaviour of rocks on the stability of underground structures which are under the influence of a high horizontal stress field. The research work was conducted through a combination of numerical modelling, laboratory testing and field investigation. A number of 2-D FE model of roadways were constructed based on the data obtained from laboratory testing and field investigations. The models were then analysed using three different solution techniques; simple linear-elastic, non-linear elastic-plastic and elastic-plastic with consideration of post-failure behaviour (softening model). Results indicated that the post-failure behaviour of rocks significantly influence the stress and displacement patterns around the roadway. The stress and displacement patterns as well as the extent of the yield zone around the roadway predicted by the softening model were in good agreement with that from the field study. Based on the results of the study, an appropriate support system has been suggested to govern the stability of roadways.

Jan 1, 1994

By John Shepherd

Pillar extraction carried out using various methods (split and lift, Wongawilli and old Ben) involves the formation of narrow fenders (commonly 7 m of coal) formed by driving "splits" for lifting off with a continuous miner. The strata above a split and fender adjacent to the goaf consists of a cantilever beam (usually >3 m thick) that extends from the solid coal and bridges across the fender. Lifting off the fender from the split in safe conditions depends upon the bridging capability of the cantilever and the fender strength. The nature and competence of the immediate and near roof, the support capability of the coal fender and the presence of faults and or joints can adversely affect the bridging behaviour of the cantilever. Insufficient knowledge of these parameters can lead to extraction under dangerous conditions. Remnants of fenders ("stooks") also support the cantilever and their dimensions are critical to obtain regular caving and goaf falls. Stook area, goaf roof span and roof stand-up time after lifting can be related and only a relatively small increase in Btook area of 10-15 m2 can lead to a significantly increased stand-up time, especially under a massive roof. Such conditions strongly influence the redistribution of abutment stresses and can create increased outbye pillar loading. Based on detailed underground geotechnical investigations, it is concluded that strata caveability, roof cantilever behaviour, fender H:W ratio and remnant stook size are all critical parameters for successful and safe pillar extraction.

Jan 1, 1992

By D. M. Shu

A two-dimensional finite element modelling technique is applied to predict the subsidence movements on a sloping ground surface above a completely mined panel. The modelling is carried out for the surface both directly and using a combination of an equivalent horizontal surface and a rays projection method and the result compared. The rays projection method provides the subsidence components on a sloping surface from the corresponding ones on an assumed equivalent horizontal surface through the point of mean elevation of the relevant part of the sloping surface. This method is used next to compare the subsidences, horizontal displacements and horizontal strains from the mining of a given panel at the surface for different inclinations. The results show that the magnitudes of the subsidence components are greater on the dip side of the slope from the point of the mean elevation, than the corresponding ones on the rise side and the asymmetry increases with the inclination of the surface. The findings are also compared with those of other research workers.

Jan 1, 1992

By Anton Sroka, Antoni Tajdus, Axel Preusse, Krzysztof Tajdus

"In Europe, the magnitude and range of mining deformation predicted on the surface have been, in most cases, determined using methods based on Gauss' influence function (e.g., Knothe's theory, Ruhrkohle method, Stochastic method). The increase in the application of numerical methods (finite element method FEM, finite difference method FDM, etc.) provides an opportunity to offer a different approach in describing mining deformations. However, this phenomenon is very complex, and due to numerical limitations, a two dimensional analysis was made (in plane strain) in most cases. Such 2D models could not accurately describe the mining geometry and geological conditions. The authors of this paper carried out the calculations in 3D models which describe a mining situation and the character of the strata in one Upper Silesian Polish mine. Furthermore, the authors include some tips for three-dimensional modeling.INTRODUCTIONThrough the years, many numerical models have been used to describe a phenomenon of underground mining exploitation influence on the ground surface. However, such rock masses are highly disturbed (cracks, fractures, changes in water conditions, etc.), and it is very difficult to suitably describe, in a mathematical manner, such materials. Therefore, many of the numerical models created have been corrected in various degrees.At first, models widely used to describe the behavior of strata in the region of exploitation appeared as elastic models, where scientests assumed that a whole strata behaved in a linearly elastic manner, according to Hook's law. Those models have been modifed to received suitable VALUES (of settlement and range of subsidence troughs. Scientests created this amongst others: elastic models with contact between the rocks layers (Shippam, 1975; Salamon, Chugh and Yang, 1993), elastic models with no tension (Chrzanowska-Szostak, 1988), and elastic models with a contact on the subsidence limit plane (Tajdus K., Tajdus A., 2005). However, in most cases, those models did not bring the expected results and the differences between shapes of measured and the calculated subsidence trough were substantial."

Jan 1, 2010

By Stephen C. Tadolini

The risk of injury caused by minor roof falls continues to increase in underground mining. Most ground control injuries result from small rock falls that occur in a supported area, but do not involve the failure of the support system. In the roof, these are the "skin failures" that occur between previously installed primary or secondary bolting systems. To minimize skin failures and the associated accidents, several devices were designed and tested in the laboratory to maximize stiffness, minimize material thickness and weight, and ease material storage and handling on roof bolting machines. The goal of this project was to design and evaluate devices that can be installed with traditional primary or secondary roof supports, and that arc easy to handle/install under temporary or previously supported roof.

Jan 1, 2001

By Hanjie Chen

Mining experiences have shown that in a pitching seam, roof behavior is significantly different from a flat seam. Uphill mining usually experiences more roof problems than downhill mining. Based on a case study at RAG American Coal Company, Willow Creek Mine, this paper presents the roof control problems experienced in a high pitching seam. Then, finite element modeling is conducted to analyze the roof stress distribution for an entry developed in different directions relative to the seam strike. The results shows that seam inclination has a significant effect on roof stability in terms of tensile stress. Uphill mining experiences higher tensile stress than downhill mining. The modeling technique utilized in this analysis presents a first of kind methodology.

Jan 1, 2000

By Don Berger

Highwall scaling, bolting and technical blasting are important aspects in the remediation of existing highwall exposures. Proper planning, design and research are important first steps in the development of long term stability. Research into old workings and their influence on highwall stability control the planning and design. These steps are followed by improvements in blasting techniques, highwall monitoring programs and constant evaluation of the results. Recently, due to a number of factors, the highwalls of the Open Cut Mine have started to deteriorate, creating both operational and potential safety problems. Geologic setting, highwall design, mining operations, old workings and weather have combined to create adverse conditions that have allowed sections of the highwalls to become unstable. Homestake Mining Company has developed a program to alleviate the existing ground control problems and to decrease the effect operations has on future highwall stability.

Jan 1, 1996

By R. Karl Zipf

Stress analysis programs such as MULSIM/NL, LAMODEL, MinSim 2000, and EXAMINE TAB are used in the mining industry to analyze stresses and displacements in coal mines, platinum mines, gold reefs, and tabular-type deposits. These relatively simple numerical models can efficiently simulate yielding and failure of a rock mass near a mine opening and subsequent stress transfer. The main input parameters for these models are a family of nonlinear stress-strain curves for the in-seam material. For many applications of these models, such as in coal mining, extensive field measurements and observations exist from which to estimate these stress-strain curves and calibrate the numerical models; however, such measurements are lacking for other types of mines. A three-step method is presented to determine nonlinear stress¬strain curves for boundary-element (BE) programs used in many mining applications. The method requires a suite of laboratory¬scale strength tests at various confining pressures. Note that this analysis uses laboratory-measured strength and modulus properties of alluvium. The dependency of the mechanical properties of alluvium on scale has not been established, although more tests are being planned. However, it is believed that the relative comparisons performed are valuable regardless of scale effects. First, the FLAC2D computer program is used to model the laboratory tests and determine cohesion (c) and friction angle (0) for a Mohr-Coulomb material model. Second, another FLAC2D model uses the c and 0 values to calculate vertical stress and strain around a single opening in the rock mass. This model calculates the stress-strain path of points at various distances from the opening boundary. Finally, based on these stress-strain paths, the stress-strain curves needed for a BE analysis are derived. This three-step method was demonstrated in a large, flat-lying underground test facility in very weak rock. The BE analyses agreed well with observations of failure at the test facility and provided a basis for evaluating the behavior of alternative layouts.

Jan 1, 2003

By Yingxin Zhou

Data from these field studies and previous case study data have been combined to define ultra-dose seam mining environments and relate them to observed failure conditions. A rating system for ultra-close multi- seam design has been developed and field studies have verified the applicability of the design criteria according to geologic structures, lithology and spatial data. This rating system has been combined with design and depth considerations to create a protocol for quantitatively predicting potential damage in ultra-dose seam mining conditions. A brief discussion of the characteristics of ultra-dose seam mining and its related failure mechanisms is also presented

Jan 1, 1990

By Michael Alber

Pullout tests on resin grouted rock bolts have been executed in coal mines and surface test sites. The goal of this study was to provide some qualitative information about the rock mass quality from mandatory tests with a bit little more effort. Movements of rock bolt head and steel plate at different load levels were analyzed and were found to yield information about the rock mass deformability. The tests were interpreted similar to plate bearing tests and a rock mass compressibility index C was assigned. This index reflects the complex interactions between the rock mass, resin grout and bolt under load. Although further research is necessary it may be concluded that those tests may aid in recognizing geological conditions.

Jan 1, 2003

By Gift Makusha

Pre-feasibility work at Goedehoop Colliery indicated that stooping of the undersized pillars could be undertaken safely and economically. In light of the findings a decision was taken in may 2003 to undertake the project in the 600 area where three panels (628, 630 and 632) were identified for pilot test sites. The findings of the pre-feasibility studies were presented in a paper to the 22nd International Conference on Ground Control in Mining held at Morgantown in 2003 (1). This paper is a progress report for the project 12 months down the line. Work commenced to prepare the sites for mining including, acquisition of equipment, equipping the panels, selecting and training people to undertake the project. Three monitoring sites were set up distributed evenly along panel 628. Each site comprised of a surface extensometer station in the overburden strata adjacent to a pillar underground containing hard inclusion vibrating wire extensometer cells. This combination would be used to record pillar loading ahead of stooping as well as the depth of caving and strata deformation in the goal zone behind the stooping face. In July 2003, support work began to secure the roof and rib sides. The support was required to be at least three-pillar center distances ahead of the mining front to ensure that the effective stooping zone is secured at all times. The NEVID method of pillar extraction developed at Sasol and described in detail by Ismet and Moolman (2) in a Coaltech 20-20 report was adopted for the pilot project. As part of training the selected stooping team was send for a week to Sasol's Bosmanskrans Colliery to familiarize with the NEVID method of stooping. Further training sessions were carried out on site especially on the use of Mobile Roof supports. The first cut was taken on 20 August 2003 by implementing a form of chequerbord mining taking every second row of pillars. Three rows were mined this way which period was considered training to get workers familiar with the new equipment and mining method. On the fourth row the full design span equivalent to mining 4 pillars in a row was implemented taking out all the pillars in successive rows. Production figures gradually increased from 300 to more than 1,000 tons run of mine coal per shift. Panel 628 was mined out at the end of December 2003 and the second of three panels (630) is being mined. Substantial data from the monitoring set up has been recorded since the start of the project. Monitoring will continue to the end of the pilot project and the data will be analysed and fed back into the design tools to improve the design in future undertakings. The pilot project has been a success so far and other old workings are being evaluated for stooping.

Jan 1, 2004

By Christopher Mark

The past decade has provided a wealth of practical experience with longwall pillar design. Design formulas developed specifically for longwalls have proven their value in numerous applications. Analytic methods, including numerical models, have a1 so made important contributions. These advances have been based on basic research into abutment loads, coal pillar mechanics, and the interaction between pillar performance and entry stability. The goal of this paper is to review the state of the art in longwall pillar design from the standpoint of the practitioner. Actual case histories are presented to illustrate the current capabilities and limitations of pillar design methods. The paper also discusses the advances that can be expected in the future.

Jan 1, 1990

Case study data were analyzed to develop and quantify empirical stress transfer relationships between seams for both longwall and room and pillar mines. Layering in the innerburden and the distance between seams were determined to be the controlling factors. To evaluate the effect of bedding planes on stress transfer, laboratory studies were conducted using layered, low modulus gravity loaded photoelastic models. Parameters investigated were thickness, number of discrete layers, modulus and friction between layers. Results showed that there was significant distortion of the pressure bulb in highly laminated conditions which correlated with the results of empirical analysis. Relationships developed were used to modify the results obtained from numerical modelling between multi-seam longwall operations. Research conclusions were demonstrated using case studies.

Jan 1, 1995

By C. Babcock

This Bureau of Mines report considers some equations for mine pillar design from 1833 to the present. Most of the equations are of essentially the same kind, using pillar width to height relationships. The effects of end constraint and test volume size, that were implied in some of these early equations have received special emphasis in recent years. Experimental testing in the laboratory throughout the period given has been on prisms or cubes of coal or rock. Most of the present concepts have been known since about 1912. Wilson has recently emphasized the effect of end constraint in his confined core concept, but a number of other earlier relationships have indicated an awareness of the effects of constraint as well.

Jan 1, 1981

By Mario G. Karfakis

Mining related subsidence is a major concern over abandoned shallow coal mines. Many of the subsidence prone areas are presently used or will be used in the future for residential housing development. Concern over mine subsidence is inhibiting the development of surface land uses on previously mined area. This concern prompted public officials to realize the need to develop guidelines which can be used to assess and reduce the risk of mine subsidence damage to building and other improvements. Subsidence and the associated ground movements must be defined before one can relate them to building damage. Surface movements resulting from underground coal mining occurs in two phases termed as: active subsidence and residual subsidence. Active subsidence refers to all surface movements occur in^ simultaneously with the mining operations, while residual subsidence is-that part of the surface deformation which occurs following the cessation of mining. Residual subsidence is the major concern over abandoned mine lands. The duration of residual subsidence is of particular importance from the standpoint of damage at the surface to structures built after the mine has been abandoned. Time spans during which surface subsidence may occur, vary markedly with the mining method being used. In total extraction methods, such as longwalls, subsidence is induced rapidly, beginning almost immediately after mining. Subsidence concurrent with coal extraction is desirable for a safe longwall mining operation. Usually subsidence is complete within a relatively short time. The remaining settlement occurs as residual subsidence due to the gradual compaction of the subsided ground. The relative proportion of the residual subsidence movements is dependent upon the presence of remnant pillars and roadside packs. rate of face advance and depth of workings. In partial extraction methods, such as with room-and-pillar systems. major occurrences of surface subsidence may be delayed for decades until the support pillars and/or the roof have substantially deteriorated and collapsed. The actual time involved depends on a number of factors such as the strength of coal, roof, and floor, extent of fracturing. presence of water, depth of workings, pillar size and percentage extraction. Consequently residual subsidence is more likely to occur over abandoned room-and-pillar mines. The following sections define subsidence over abandoned mines, review the proposed mechanisms, identify the controlling factors and examine the prediction methods.

Jan 1, 1987