Search Documents

By Kot Unrug

Mine seals are necessary in nearly every mine to isolate mined-out areas from the ventilation network. There is a large number of seals in active mines and that number continually increases as the development spreads across the reserves. The recent accident caused by the failure of seals in the Sago mine resulted in new regulations. These regulations have been set based on a principle of eliminating the risk of failure, rather than the sound engineering and understanding of the conditions that may cause seal failure during an explosion of methane in sealed areas of the mine including the probability of such occurrences. This paper discusses the following subjects related to mine seals: The potential causes of methane explosions and the dynamic effects of pressure wave propagation. Seal materials and methods of construction in view of the interaction of the seal with the host rock environment as well as requirements for gathering geotechnical data. The design of seal dimensions is based on loading conditions, therefore the probable ranges of such loading is reviewed. There is also discussion of possible methods for shielding of seals from pressure pulses following an explosion. Particular seal?s types are examined in reference to the conditions at the seals location. A novel design is presented that will be a low- cost solution for the sealing of mined out areas. Recommendations are given for further research leading to a rational engineering system for design of new seals in coal mines.

Jan 1, 2008

By David L. Kuck

This paper describes a system for providing structural, support in underground mines, employing water ice for pillars. packwalls and brattices. It consists of a refrigeration brine chiller, brine circulation system, and disposable plastic containers. The system provides for the timely freezing of uniform ice pillars, and for ice maintainance and/or melting on demand. Unique, useful ice properties include: expansion upon freezing, resilience to dynamic loads, and plasticity. Ice will not dilute or contaminate coal or ore. Economic advantages include: 1) lower labor and material costs (water can be piped to the ice pillar site through mine-water, spray-water, or drill-water lines); 2) replacement or supplementation of timber. concrete or other roof support equipment; and 3) potential use of ice brattices as ventillation control; and 4) conversion of ice bratices to ice pillars upon retreat. See Figure . A safety advantage for personnel and equipment is that ice pillars can be placed in hazardous sites, by remote control, if neccessary, without human entry. All filling, freezing and melting operations can be controlled from a safe distance.

Jan 1, 1987

By Richard Campbell

Effective strata control, utilising fully encapsulated resin grouted roof bolts is dependent on the installed quality of the reinforcement elements. Resin based grouts are the main form of rock bolt anchorage in the underground coal industry in Australia and New Zealand. To be effective the system requires the mixing of the catalyst and mastic components of the resin as well as shredding of the cartridge that contains the resin. Over the past six years Solid Energy New Zealand Ltd (SENZ) has pioneered an extensive work programme quantifying the effects and extent of poor installation quality due to gloving, poor mixing and loss of encapsulation (Pastars 2003, Campbell et al 2003, Mould et al 2004, Campbell et al 2005 and Pastars & MacGregor, 2005). The One-Step Bolt (OSB), an innovative bolting solution designed and manufactured by Hilti Pty Ltd offers a self drilling, single pass bolting method that eliminates gloving, guarantees mixing quality and encapsulation performance of the installed product while not jeopardising the mechanical performance of the bolt. This paper details recent work undertaken by SENZ designed to understand and quantify the system performance of the Hilti OSB in New Zealand?s thick coal seam mining environments.

Jan 1, 2006

By Kevin Jinrong Ma

Underground mines often experience roof falls in entries, crosscuts, and intersections of active mining sections, main travel ways, and belt entries. Roof fall heights greater than 20 ft (6 m) make re-bolting of the newly exposed roof dangerous and impractical. To protect mine personnel, belts, moving vehicles, and other facilities, mine operators typically install steel structures such as square or arch sets in the roof fall areas. Wood lagging is usually installed between the steel-sets to enclose the area and protect the entry from recurring falls. Usually the void space above the steel-sets and laggings is backfilled. However, backfilling high roof fall voids is costly, which causes some operators to leave the voids open. In this case, durability of wood over time and the capability of the steel-set and wood lagging to resist falling rocks are unknown. During the last few years, Keystone Mining Services, LLC (Jennmar Corporation affiliate engineering company) designed, tested, and developed an impact-resistant lagging system to protect steel-sets1. Various steel-sets protected with the impact-resistant lagging were approved by MSHA and installed in different underground roof fall rehabilitation projects. This paper presents (1) design, development, and laboratory testing of the patent-pending impact-resistant lagging panel, (2) steel-set design methodology according to the American Institute of Steel Construction (AISC) national standard, and (3) impact-resistant steel-set design method based on Law of Conservation of Energy. Two underground cases are reviewed to demonstrate the successful application of the impact-resistant lagging system.

Jan 1, 2011

By Nikolaos Polysos

For the planning and driving of gateroads supported by roof bolts a practical concept has been developed in order to determine the geological and rock mechanical parameters derived from exploration drillholes. Based on this, an assessment scheme for the design of roof bolting has been established. The new methods of investigation comprise of geotechnical logging of drill cores for the determination of structural-geological rock characteristics and complementary geophysical well-logging which enables the evaluation of petro-physical and rock mechanical properties. The tools and their measurements will be briefly presented. The relationship between the geophysical log readings and the geotechnical parameters will be illustrated. The aim of the data acquisition is to improve roof bolting design which is based on the assessment scheme. This will be adjusted to the prevailing rock mechanical conditions and stands up to the required stability of the gate roads. In order to ensure consistent data acquisition, a method of core logging has been standardized for the respective demands. To achieve this it was necessary to introduce specific parameters and new methods. For the recording of linear and planar structural elements at the drill core, a special system for the documentation of the angles in relation to each other has been set up. The rock mechanical parameters and their acquisition will be explained. In order to carry out an objective analysis as fast as possible, software has been developed for the acquisition, management and presentation of the data. These programs and their functions will also be presented. The software is characterized by being user-friendly and the flexibility of its interfaces, Different options for the combined presentation of input and evaluated data give a more objective basis for the planning of roof bolt design. Examples will illustrate the operational implementation of the results during the planning and driving phases.

Jan 1, 2001

By Brian G. D. Smart

A scheme is presented whereby the complexities of design and operation of a hydraulically powered coalmine support are modelled using the finite element method. This enables predictions to be made of the interaction of the support with its environment in a variety of operating conditions. The model is a two dimensional representation. The modelling scheme was applied in two case studies. In the first, the performance of a four leg support was uprated by increasing the front leg force. The finite element model enabled changes in overall support performance to be verified. In the second case study, the change in lateral force developed by a two leg support was assessed with changes in support operating height and floor foundation stiffness. The modelling scheme is capable of further development with the possibility of extending the model into three dimensions and the addition of control elements that would enable an actual mining sequence to be represented.

Jan 1, 1992

By John C. Stankus

ldentifcation of potential roof problems in coal mines has long been a complex issue due to the wide variety of mining and geological conditions. It is well known that mine roof falls are related to many different factors such as roof strata properties, sandstone channels, regional and localized horizontal stress, vertical stress, and tectonic stress. Many times, a combination of these factors causes roof problems. Through years of ground control experiences, Keystone Mining Services LLC, (KMS) has developed a Roof Instability Rating (TUR) system to predict potential roof problems. The first RIR analysis was presented at the 19th Ground Control Conference (Watts, et al., 2000). The RIR system includes: quantifying each individual factor, weighting each factor, combining individual factors, finalizing the RIR, and setting the criteria for the areas where special support is needed. In this paper, the application of the Roof Instability Rating (RIR) system at Enlow Fork mine will be presented.

Jan 1, 2001

By Karsten Zimmermann

Surface deformation monitoring is required all over the mining industry. For example oil and gas companies need this information to support exploration and production activities and to detect impacts from surface subsidence of existing hydrocarbon fields. Also opencast mines require large area information of subsidence due to dewatering of the overburden. Because of this, a lot of surface deformations measurements with GPS or traditional geodetic measurement techniques have been conduced during the last decades. This paper presents the actual capabilities to analyze GPS data using the state of the art Bernese GPS Software for GPS post processing. A new way of monitoring subsidence is a combination of GPS and satellite InSAR data. Considering this it is hoped that a combined strategy will permit receiving overall more information by integrating high point density of InSAR and accuracy of GPS. DMT is one of the leading actors on GPS services especially for monitoring surface movements from underground activities e.g. mining, water pumping or oil and gas exploitation. The paper will discuss preferences and problems of this approach on results of a current project of DMT.

Jan 1, 2008

By Nicholas Chlumecky

One of the most dangerous jobs in mining is that of resupporting the roof after a fall has occurred. The resulting cavity may be more than 30 feet high, with relatively unstable sides and roof. It is often impossible to proceed with rehabilitation without exposing men and equipment to unsupported rock. Temporary supports provide margin- ally effective protection because of the lack of available footing. Furthermore, the usual supports in rehabilitated fall locations are not permanent, require frequent maintenance, and fail to eliminate some remaining serious safety hazards. This is typically the case for high cavities where loose rock drops from considerable heights from between roof bolts. Supports made of cribbing, beams and additional cribbing to the high points of the fall in many cases do not provide good protection due to the deterioration and shrinkage of timber. In mines, high cribbing frequently loses contact with the roof and thus provides no protection against rocks peeling off the sides. This is true in spite of the fact that at time of installation the cribbing was wedged tightly to the roof. Therefore, when considering the difficulties which occur with current practices, the objective is to find alternate methods of resupporting the high roof after a fall.

Jan 1, 1981

By Axel Preusse

To detect improper deformations of a roof bolted roadway in order to reduce inner mine damages in the most early stage and to initiate suitable countermeasures if necessary, several different measurement systems were used for monitoring a roadway's stability on the hardcoal mine "Auguste Victoria" (DSK AG). In this paper the different convergence measurement procedures are described and their respective results are introduced. Subsequently the results of the single measurement methods and procedures are correlated with each other.

Jan 1, 2000

By Michael Alber

Coal mining by the longwall method typically causes seismic events. This paper describes the research on mining induced seismicity around two specific longwalls at 1100m depth under several old longwalls. A local network featuring 21 geophones has been installed, underground core drilling and an extensive rock testing program were executed. A rock mechanical model featuring a multi-layer strata was created for use with numerical analyses. Seismic events were localized and three different event types are described. Focal analyses yielded distinct modes of failure. Those types are explained by different failure mechanisms, namely fault activation, remnant pillar punching and beam failure. The use of rock mass classification, rock mass strength criteria and in situ stresses together with 2D and 3D numerical analyses allows evaluating the findings from seismology approaches. Conclusions are drawn that the orientation of longwall with respect to the major horizontal stress orientation plays an important role in mine induced seismicity.

Jan 1, 2008

By Erdal Unal

In gate roads where supports are subjected to dynamic loading four times due to retreating longwall panels, it is a real challenge to replace the rigid arches with flexible reinforcement systems and yet to provide safety and stability of these openings within better economical limits. The results presented in this paper are based on a three years of research project aimed at developing safe and economical support systems for gate roads in Çayìrhan coal mine. Çayìrhan -Mine Project includes laboratory and field studies, design analysis, pilot scale design applications and performance monitoring. Based on outputs of the design approach developed, four types of bolts, namely, Split Set, Yielding Super Swellex, Sis-Resin, and Fosroc-Resin bolts were installed in a gate road together with widely spaced yielding steel-arches. In order to compare the performance of these flexible support systems and to provide feed back for the design approach, a monitoring program was initiated.

Jan 1, 1993

By Larry DeGraff

With the increase of new mine development in the past several years, many coal mines have decided to self- perform the design and construction for their slope development projects. The development process of determining the proper configuration is challenging, and a major economical consideration. Greenbrier Smokeless Minerals engineering staff and consultants, along with DSI/American Commercial, developed a support configuration that was best suited for their slope. The developmental process took into consideration the length of slope, depth of slope at the high-wall transition, economics of a single or multiple entries, waterproofing, stresses on the steel supports and lagging during the backfilling operation. This paper describes the developmental concept of using a single entry, side by side configuration, using steel ?Banjo String? supports with steel plank lagging, to develop a long term permanent installation in a cut and cover application.

Jan 1, 2009

By Maleki. Hamid

The U.S. Bureau of Mines implemented an inte¬grated static and geophysical monitoring program in a southern Wyoming mine to study changes in seismic wave propagation properties in roof strata. The purpose was to develop techniques to assess roof stability problems. The work consisted of record¬ing deformation and stress histories and calcu¬lating seismic velocity profiles. In addition. geology and roof conditions were mapped; the in¬struments were initially installed at the develop¬ment face; monitoring continued until the mecha¬nized retreat face retreated within 60 m of the instruments. Mining geometry consisted of a three-¬entry gate system using 5.2-m-wide pillars at depths of 426 m. Results were analyzed using stan¬dard history plots, velocity tomographs, and numer¬ical modeling techniques. Changes in velocity. frequency, amplitude, dynamic elastic modulus, and dynamic Poisson's ratio were related to roof defor¬mation, fracturing, and support requirements. A reduction in seismic velocity of 17 pct occurred after 60 mm of roof deformation following installa¬tion of supplementary support. Static measurements revealed significant dilation in the mine floor, spreading to the pillar and the mine roof. Failure was initiated in the floor as a result of uniform pillar penetration.

Jan 1, 1993

By Dennis R. Dolinar

A room and pillar coal operation in central Pennsylvania was experiencing roof cutters and long running roof falls caused by high horizontal stresses. The roof conditions created hazards for the miners, and caused several production panels to he abandoned prematurely. The mine requested assistance from the National Institute for Occupational Safety and Health (NIOSH) in applying the "advance and relieve" mining to reduce the affects of the horizontal stress during panel development. The "advance and relieve" plan that was developed called for removing a pillar on one side of the panel as it was being advanced, thus creating a cave. The caving then relieved a portion of the horizontal stress across the panel. Because the horizontal stress direction is key to the success of this method, stress mapping as well as mining experience was used to establish the direction of the horizontal stress. Subsequent field measurements provided an estimate of the stress magnitude. Three panels were mined using this technique, and good roof conditions were achieved in all these panels. Instrumentation was used to monitor the stress changes in the roof created by the cave. Stress relief of over 1.000 psi was measured 120 ft from the cave and to depths of 20 ft into the roof. The lateral extent of the stress relief zone across the panels appears to be about 400 to 500 ft. This case history has provided much insight into the practical application of the "advance and relieve" method discussed in this paper.

Jan 1, 2000

By S. P. Singh

Destress blasting is commonly used in the mines to minimize the occurrence of rockbursts. The fracturing created by destressing in the vicinity of the face reduces the stress concentration by pushing the zone of high stress deeper into the rock mass. But the destressing practice by blasting may be devastating near the faults or other sensitive high stress zones. To avoid severe rockbursts in such situations, the application of chemical destressing has been proposed in this paper. A laboratory investigation was conducted on the rocks in the Sudbury basin to examine the change in the material properties with an aim of assessing the feasibility of destressing by chemical means. The favourable change observed in the rock properties led to the suggestion that the injection of surfactants in boreholes would enhance fracture propagation similar to what is currently done by blasting but in a safer, inexpensive and non-violent manner. The current destressing practices in Ontario mines have also been reviewed in this paper.

Jan 1, 1987

By Changsheng Song

With increasing depth of coal mining in China, the number of coal and gas outbursts has been increasing for years. By means of destressing the protective seam, the gas in the protected seam is drained to reduce gas concentration in the high gassy seams, thus ultimately attaining simultaneous extraction of coal and gas. Base on the simulated material scale modeling and numerical simulation, the protective seam mining method was practiced at No. 8 coal mine in Pingdingshan city. After extracting the No. 15 seam, the overlying strata movement and the deformation of No. 9-10 protected seam were studied. The experiments showed that it was feasible to destress the protected seams with large interburden thickness. As the protective seam was being mined, the protected seam experienced dynamic movement process and the change in vertical stress in the No. 9-10 seam assumed ?W? shape. When the face had advanced 656 ft (200m) from the setup room, the No. 9-10 seam was fully destressed, resulting in easy gas drainage in the destressed zone. Recommendations on mining sequence of multiple seams mining in the Pingdingshan coal areas were made.

Jan 1, 2008

By David Bigby

A remote reading dual height telltale system has been developed to provide mine management with early warning of impending roof failure. This system is a logical development from the visual dual height and triple height telltales which are increasingly being used worldwide for routine monitoring of mine roof. The paper describes the principles and history of telltales from their origins in France, their refinement and routine use in the UK and their subsequent spread around the world. They are now being used in various forms in USA, Canada, Germany, Spitzbergen (Norway), Poland, Ukraine, Russia, Australia, South Africa, Mexico, India, Egypt and China. The remote reading telltale system has coal mine intrinsic safety approval in Europe and the United States (MSHA) and the first commercial system was installed in a German colliery at the beginning of the year. Up to 100 dual height telltales can be connected, in a simple "daisy chain" configuration, to each of 4 underground interrogation units. These are connected through a twisted pair link to a surface computer which displays the readings, updates the database, generates warnings and provides the user interface. The paper describes the features and principles of operation of the system which differs considerably from conventional mine-wide monitoring systems. A European Community funded research programme is currently underway with the aim of developing improved alarm generating algorithms including evaluation of interfacing a neural network to the system. The paper concludes by exploring other potential applications of the system for ground control monitoring currently in development, including extensometry, stope closure monitoring and support load measurement.

Jan 1, 2001

By Khaled Morsy

The studied mine extracts the Sewickley seam using room-and-pillar method. The overburden at study site ranges from 400 to 800 ft. Eight years earlier, the Pittsburgh seam was mined 80 ft underneath the Sewickley seam. Parts of the mains at the study site experienced problems of rib spalling associated with floor heave. Numerical modeling was used to explain the mechanism of ground control problems encountered at the mains of the upper seam. The modeling results show that the ground control problems encountered were caused by multiple seam interactions with the previously mined longwall panel of the lower seam. Based on the modeling results, a criterion to predict the probability of multiple seam interactions was proposed.

Jan 1, 2006

A high strength steel strand bolt has been developed by Barrett, Fuller & Partners as a replacement for conventional rigid bars for primary roof support in coal mines. It is based on a 23mm diameter multiwire steel strand with a tensile strength of 55 to 60 tonnes, The paper summarizes the development of FLEXIBOLT flexible roof bolts, their reinforcement performance and their potential to provide operators, currently reliant on medium to high density roof bolting systems, with a viable, low density roof bolting system offering high roof reinforcement capacity along with the option of installing bolts longer than headroom, in a single pass at the face.

Jan 1, 1993