Search Documents

By Y. Luo

An extensive subsidence research program conducted by the authors has greatly improved the accuracy and the capabilities of subsidence prediction under complicated mining and surface conditions. The techniques developed for assessing and mitigating subsidence influences on various surface structures have been applied in numerous cases with a very good re- cord of success.

Jan 1, 1997

By Madan M. Singh

Mining under bodies of water such as oceans, lakes, rivers, streams, ponds, and other impoundments, is not a new technique. However, in the United States it has been fairly restricted to date. In order to recover the maximum amount of the nation's reserves, in the future, it is important that further mining under such bodies of water be planned. However, it is imperative that this is not done at the expense of danger to the nation's miners or appreciable property damage. If all the bodies of water are considered large, and it is assumed that these constitute a hazard when mining in their vicinity irrespective of their size and geometry, a significant percentage of the coal reserves are likely to be sterilized. How- ever, by adopting special mining plans and procedures, it may be possible to release reserves for exploitation that would otherwise be unmineable since the surface of bodies of water below which they lie are relatively small in size. In 1977, the Bureau of Mines issued Information Circular (IC) 8741, entitled "Results of Research to Develop Guidelines for Mining Near Surface and Underground Bodies of Water". This document was based on the work done by Skelly and Loy (under Contract No. H0252083) and K. Wardell and Partners (under Contract No. H0252021). How ever, these guidelines have limited application, because these did not (1) define the bodies of water of concern, and (2) take into account the nature of the strata being encountered. These guidelines assumed that all bodies of water which would be undermined were large. For the purposes of this discussion, water bodies may be divided into three categories, depending upon their potential to cause damage to the underlying mining activity: ? catastrophic ? major ? limited Bodies of water which pose the threat of catastrophic destruction in the mine, should there be an inrush, include oceans, large lakes, big inland reservoirs, and rivers that could flood the mine complete- ly in a short period. Those with major potential for damage would include lakes and streams which might present a danger to both life and property if not considered in the mining plans. Finite bodies of water which have a volume considerably smaller than the mine volume offer a limited potential for damage in the case of an inrush. These include flowing streams which have a relatively small rate of replenishment and which can be dealt with by pumping or isolation in the event of a breakthrough into the mine. Such bodies of water may be inconvenient and cause a temporary disruption of production, and could even cause some damage to equipment, but only in rare instances would personal injuries occur. The scope of this paper is limited to the exploitation of stratified mineral deposits with overlying -face bodies of water. Vein and dessiminate ore deposits are not discussed, nor are breakthroughs into adjacent mines in the same horizon. Overlying, water-logged strata also pose a serious threat to mining, but are not treated in this discussion. Pending further investigation these strata may be considered as bodies of water with catastrophic potential for damage, with the base of the strata being considered the bottom of the water body. When the body of water is large, so that it may cause catastrophic damage to the mine in the event of an inrush, the guidelines suggested in IC 8741 are applicable. In order to develop criteria and procedures for mining under smaller bodies of water, however, it is necessary that the nature of the strata disturbance due to underground mining be examined.

Jan 1, 1981

By Marek J. Mrugala

Coal strength based on scaled uniaxial compressive strength from the laboratory and back calculations from in-mine observations of pillar stability indicate that material strength scaling rules are open to debate. Analyses presented indicate that the application of scaling factors lower than 0.5 provide a better correlation with field observations of pillar stability.

Jan 1, 1989

By Erdal Unal

In order to define the support parameters, by use of empirical approaches, it is particularly important to analyze the rock-load height that should be controlled by supports. The controlling mechanism however, depends on the type of support used there- fore, the rock loads should be treated differently. In this paper, an empirical equation is introduced which relates the rock-load height (ht) to a quantitative rock quality index (REIR), and roof span (B) as fallows:

Jan 1, 1986

By Peter Zhang, Todd Minoski, Mark Van Dyke, Daniel W. H. Su

"This paper presents the results of a 2017 study conducted by the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Mining Research Division (PMRD), to evaluate the effects of longwall-induced subsurface deformations within a longwall abutment pillar under deep cover. The 2017 study was conducted in a southwestern Pennsylvania coal mine, which extracts 1,500-foot-wide longwall panels under 1,185 feet of cover. One 650-foot-deep, in-place inclinometer monitoring well was drilled and installed over a 150-foot by 275-foot center abutment pillar. In addition to the monitoring well, surface subsidence measurements and underground coal pillar pressure measurements were conducted as the 1,500-foot-wide longwall panel on the south side of the abutment pillar was being mined.Prior to the first longwall excavation, a number of simulations using FLAC3D™ (Itasca, 2017) were conducted to estimate surface subsidence, increases in underground coal pillar pressure, and subsurface horizontal displacements in the monitoring well. Comparisons of the pre-mining FLAC3D simulation results and the surface, subsurface, and underground instrumentation results show that the measured in-place inclinometer casing deformations are in reasonable agreement with those predicted by the 3D finite difference models. The measured surface subsidence and pillar pressure are in excellent agreement with those predicted by the 3D models. Results from this 2017 research clearly indicate that, under deep cover, the measured horizontal displacements within the abutment pillar are approximately one order of magnitude smaller than those measured in a 2014 study under medium cover.INTRODUCTIONDue to a recent shale gas boom, approximately 1,400 unconventional shale gas wells have been drilled through active and future coal reserves in Pennsylvania, West Virginia, and Ohio over the past 15 years. These shale gas wells have penetrated many coal seams, such as the Sewickley, Pittsburgh, Upper Freeport, and Kittanning seams. These unconventional gas wells, whether tapped into the Marcellus or Utica formations, contain very high gas pressure. Strata deformations associated with longwall and other high extraction techniques could induce high stresses and deformations in the shale gas well casings. This could seriously compromise the mechanical integrity of the production, intermediate, and coal protection casings (Figure 1). Damaged well casings could potentially introduce high-pressure, explosive gas into underground mine workings, particularly during an extended well shut-in period, which could seriously jeopardize underground miners’ safety and health."

Jan 1, 2018

By Robert A. Stansbury

The No. 14 Mine of United States Steel Corp- oration is located at Munson, West Virginia, in &Dowell County. The mine was originally assigned 7,530 acres of Pocahontas 3, 4 and 5 Seams. Production began in 1948 with a listed reserve of 64,500,000 in place tons. It was originally intended to superimpose the 4 Seam workings with the 3 Seam and mine the two simultaneously to minimize the effects of one seam on the other. Roof control problems and economic conditions led to the discontinuance of 4 Seam workings in 1958 and again in 1980, after reopening in 1972. With room and pillar mining continuing in the 3 Seam, the majority of the 4 Seam reserves have been undermined. The mine began operation using track mounted conventional equipment. Off-track conventional equipment was next used, and in 1957 continuous miners were introduced. Since this tie, continuous miners on room and pillar work have been exclusively used with the exception of a brief shortwall trial in the 4 Seam in 1975. By mid 1982, 3 Seam mining will have been completed, leaving an estimated 42 million in place tons of 4 and 5 Seam coal as the focus of mining efforts. Plans for the subsequent reopening of the 4 and 5 Seam workings have been scheduled for June of 1981. With the resumption of mining, management is faced with solving the roof support problems caused by both the inherent physical conditions and undermining.

Jan 1, 1981

By R. F. Valene

This paper is not available for inclusion in the Proceedings at the time of printing. but it will be included as an insert

Jan 1, 1984

By Ulrich Langosch

In the 1990s the German mining industry introduced a new generation of shield supports. The new design of support has a maximum load capacity of 10,000 kN, making these units as strong as the shields used in Australia and in the USA. DMT took more than 3,100 underground observations in order to verify the roof fall frequency by statistical analysis. The results of this work have led to practical recommendations for roof control and the required shield support system on longwall faces. The underground observations have been correlated to Rock Mass Classification, to stress calculations and to the angle between the direction of the fissures and the direction of longwall mining_ The analysis work yielded the following two sets of results: 1. There is a critical distance between the canopy tip and the coal face (Tip to Face TF,n,). The TF,n, is predictable and relates to: the thickness of the first roof layer and its uniaxial compressive strength. The face support should have a TF that is less than the TFcrtt in every underground longwall situation. Exceeding the TF crit call immediately result in a roof fall. 2. Using the obtained regression equation DMT is able to calculate the probability of the roof fall frequency (FF), which describes the roof fall sensitivity. When TFcr;, is exceeded the predicted roof fall FF relates to: the measured support resistance (MSR) of the shield support the calculated vertical stress (p?) the fissure-direction index (DI = angle between main fissure direction and direction of mining) and the distance by which TFcrit is exceeded (ATF). Armed with these results DMT is now able to predict the critical distance between the tip of the canopy and the coal face (TFcrit), as well as the roof fall frequency, for all shield designs. By applying the new calculation method it is now possible to compare alternative longwall layouts and different shield support types under pre-set geological conditions. Mining engineers on site are therefore in a position to make the necessary roof control preparations required to run the longwall operation to maximum efficiency. The results provide a useful basis for making practical recommendations and for selecting the most effective design of shield support. The paper uses practical examples to demonstrate the R&D results and present the various methods now available for calculation and prediction in longwall roof control.

Jan 1, 2003

By Thomas M. Barczak

A survey of the longwall industry was conducted to examine the performance of modern shield technology. The results of this survey indicate that state-of-the-art shields perform better and last longer than ever before, but premature failures do still occur. In addition, longwalI operators are now using shields longer than ever before and a greater number of fatigue related failures on aging shields are now occurring. A generic assessment of these shield failures is provided, describing the nature of the failures and how widespread they are throughout the industry. An engineering assessment of shield design and factors that cause shield failures is made using both strength of materials and fracture mechanics principles. From this analysis, design practices to improve structural margins of safety and extend the life of the shield are proposed. The existence of unexpected shield failures indicate that current shield performance testing is at times inadequate. Recommendations are made relative to improved shield performance testing protocols including the benefits of testing in an active load frame such as the National Institute for Occupational Safety and Health's (NIOSH) Mine Roof Simulator. Even the most rigorous shield testing procedures, which strive to simulate in-service loading conditions, fail to consider key environmental issues, such as corrosion which is often the cause of structural fatigue failures in modern shields. The survey also indicated that hydraulic failures occur much sooner in the life cycle of a shield than structural failures, and although they can significantly degrade support capability, often go undetected for long periods of time. Methods to detect the hydraulic failures are also provided. The paper concludes with key points to maximizing shield design and life expectancy and ideas for future generation shield designs.

Jan 1, 1999

By Yoshiaki Fujii

Displacement Discontinuity Method (DDM), which was originally developed by Crouch,S.L., is a powerful tool to calculate mechanical disturbances due to tabular excavations. Three topics on DDM applications to strata control problems in Japanese deep coal mines are described. First, is numerical simulation of microseismicity induced by longwall mining in Horonai Coal Mine. Microseismicity in the mine had been monitored by a mine-wide seismic array. Location of microseismic events and intensity of seismicity were well simulated. In the simulation procedure based on DDM, first, zones where a failure condition is satisfied by the advance of mining are detected. Then, the seismic moments, which indicate the intensity of seismicity, at the failure zones are evaluated. Second, is prediction of the shaft damage due to mining in Sumitomo Akabira Colliery. In this mine, the limit angle of the shaft pillar was changed from 600 to 800 to increase the amount of minable coal volume without increasing mining depth. Displacement of the shaft axis has been measured to assess the damage due to mining around the shaft pillar. In the calculation based on DDM, a fault intersecting the shaft and the ground surface are considered. Observed and predicted displacement of the shaft axis agreed well. Third, is the roadway deformation in Taiheiyo Coal Mine. Attainable maximum stress for a roadway was calculated considering three faults intersecting the roadway. It was realized that the roadway's convergence is related to the calculated stress by simple equations.

Jan 1, 1992

By S. I. Al-Ameen

Monolithic packing systems have gained in popularity as a gate side packing method, However, there has been no detailed investigation to assess their underground strength behaviour. This work includes the laboratory and in situ investigation for strength behaviour determined on various monolithic packing materials namely Tekpak-XX, Hydropak-20, Hydropak-30, Astrapak-3R, Flashpak, Thyssen pack and Aquablends. A simple technique for assessing the pack strength was developed at the laboratory by using a penetrometer, of which penetration resistance can be directly correlated with the uniaxial strength of the pack. The in situ strength investigations were made on core samples obtained from three pipes inserted inside the pack, while the penetration test were made on the pack surface. The in situ results indicated that the packing material develops an inconsistent strength on various part of the pack which was mainly related to an inadequate mixing of grouts inside the pack.

Jan 1, 1992

By Gexin Sun

This paper presents the physical modelling results of subsurface fracture development associated with longwall mining operations and an application of image processing techniques to interpretion of the results. Physical modelling results have been obtained by employing a large sand and plaster model loaded purely by gravity as a means of fracturing the subsurface strata above the longwall excavation. The results have shown fracture development and crack propagation as a longwall face advances and demonstrated that the strength of stratified rocks, the presence and position of a weak band-, and the extraction thickness, have significant effects upon the overall fracture patterns above the excavation. Binary images of fracture patterns were scanned from the black and white photographs of the tested models using an image analyser coupled to a video camera. These images were manipulated by a custom written C program which allows the images to be processed in both vertical and horizontal direction. The images were filtered to quantitatively differentiate between vertical and horizontal fracture intensities. The vertical fracture intensity is particularly important as vertical fractures are considered to provide the main avenues for surface and subsurface water inflow into the excavation. The use of the image analysis techniques has shown a promising improvement in image enhancement and in model results interpretation in a quantitative manner. The numerical nature of the image analysis results will allow further statistical comparison with other modelling techniques to be undertaken and significantly increase the scope for use of the modelling technique results.

Jan 1, 1992

By K. Y. Haramy

Deep coal mines with strong roof and floor strata frequently encounter face and rib bursts. The burst problem becomes more severe with increased depth. While the exact causes of bursts are often difficult to determine, localized high stress zones are common to their occurrence. This Bureau of Mines report describes a study at a mine using longwall systems that experienced both face and floor bursts. The study correlates shield loading, entry closure, and forward abutment pressure increases to observed burst occurrences. The results indicate that strong roof strata that overhang behind the longwall supports create additional abutment stress. When caving lags behind the face and the abutment zone does not advance ahead of the face during mining, stresses on the face may increase to a critical level, resulting in a burst. The critical level occurs when the stress in the abutment zone exceeds the ability of the coal and/or adjacent strata to store strain energy. Caving characteristics may be improved by inducing fractures in the roof or by providing sufficient support resistance to shear the roof. Data analysis of a major burst indicated a dramatic increase in floor heave, with a maximum occurring 80 to 100 ft inby the face, and a lag in the cave line behind the face supports. Analysis of the effects of caving characteristics and floor heave on burst occurrences is presented.

Jan 1, 1987

By Erdal Unal

In underground mining today, safety and economical aspects demand a better understanding of the rock-mass conditions, particularly for design of underground mine openings excavated in weak and stratified rock mass. The rock mass classification systems, in essence, are empirical approaches utilized during preliminary design stage. These systems have been developed for specific purposes and rock mass types, therefore, direct utilization of the classification systems in their original form, for characterization of complex rock-mass conditions is not always possible. This is probably one of the main reasons why designers continue to originate new systems, or modify and extend the ones already existing. RMR and Q systems, for example, although widely used in mining and tunnelling, can not fully describe the specifications of the weak, stratified and flay bearing rock mass. Consequently, the engineering applications that would be carried out based on original RMR and Q ratings could be inadequate for making design decisions even during the preliminary design stage.

Jan 1, 1990

By Kenny D. Basnett

An analysis of the Roof Falls Data Base (RFDB) for underground coal mines in Illinois for the period 2004?2008 indicated that about 80% of the roof falls occur at intersections and are associated with geologic anomalies or a rapidly changing geologic environment. Most falls are associated with anomalies such as clay dikes, differential compaction faults, shear zones, joints and fractures, and geologic structure. Therefore, a better analysis of the geology with emphasis on mapping anomalies such as joints and fractures and their application is necessary to improve ground conditions and safety. Such studies within Illinois Coal Basin are limited. This paper presents a mapping study of the joint orientations with documentation of dip of the several lithological units that lie directly above the Herrin No. 6 Coal seam around southern Illinois. These units include the Energy Shale, Anna Shale, and Brereton Limestone. The mapping was done in three mines and the data were plotted on a stereographic projection to determine the average characteristics of joint planes. The study mines included two deep underground mines and one shallow highwall mine. This study has helped identify favorable mining and support orientations in areas of highly variable geology. These are currently under review by the cooperating coal company for experimental roof control studies.

Jan 1, 2011

By Thomas W. McClain

This paper describes the importance of considering ground control measures when importing U.S. continuous mining technology in foreign countries. Important ground control factors are discussed. Each year the USA exports a significant amount of continuous miner equipment (i.e. continuous miners, roof bolters, coal haulers, shuttle cars, continuous haulages, scoops and feeder-breakers). International customers see the opportunity to significantly improve their productivity and increase their longwall gateroad development rates by implementing the room-and-pillar (place changing) mining systems used throughout the USA. However, a number of issues are often overlooked or not thoroughly evaluated when selecting the equipment, often resulting in lower than expected productivity. Ground control is one of the critical factors that must be addressed. Since 1993, the author has assisted numerous international customers and manufacturers with implementing or improving the performance of continuous miner and room-and-pillar systems in Australia, India, Mexico, South Africa, and the United Kingdom. An essential first step is to conduct a thorough ground control study, and then integrate its findings into mine layout, equipment selection and section operating plans. Based on actual case histories, the author will present a number of examples and "Do's and Don'ts." Another key to success is the involvement of manufacturers and suppliers with customers when implementing new systems and technology. The importance of allowing for cultural evolution by both management and workers for acceptance and successful implementation of any new system is also discussed. Over the past ten years, the global coal industry has gone through some very dramatic changes. Countries that previously experienced a freight advantage, such as Australia shipping coal to Japan and Korea versus the United States, are finding they are now in a world coal market similar to other commodities and products. Today, coal prices arc stated F.O.B. at the consumer, and the origin is often irrelevant. Also, previously state-run coal industries have been privatized, such as the United Kingdom, and others such as Poland and India are currently going through the same transition from state-run to the private sector. In all cases, the key to continued viability, or survival, depends largely on reducing costs in order to compete for a market share. Two ways exist to reduce costs. First, almost everyone tries to reduce expenditures. Depending on the circumstances at a given mine or in a specific country, this helps to some point. However, most find that secondly, production must be increased to achieve the necessary cost reductions to compete in today's global coal market. As a result, over the past ten years, foreign companies and countries have looked to the USA for new mining methods and systems to significantly increase productivity. Thus, a major portion of American equipment manufacturers and suppliers sales have been exports, which has played a major role in helping to "keep-the-doors-open" for a number of companies through the lean 1990's, when American coal companies were postponing capital expenditures and expansions. As foreign companies and countries have looked to the USA for ways to improve productivity, they have become particularly interested in continuous miner equipment systems and most often "room-and-pillar," "bord-and-pillar" or "place changing" mining systems for four reasons. First, in countries such as the United Kingdom and Germany, who have been longwall mining for generations, there remain numerous remnant small pockets of reserves in existing mines that are either too small or too difficult to longwall mine, and are conducive to the flexibility of continuous miner systems. Second, for countries such as Australia, who have experienced the constant problem of developing longwall gateroads in a timely manner to avoid longwall move delays, new or alternate methods are required. Third, companies and countries using roadheader machines on coal production are recognizing the increased productivity potential of continuous miner equipment. Fourth, countries such as South Africa and India, where a substantial amount of the production comes from conventional mining methods, "drill-and-blast", companies are recognizing the opportunity to improve by implementing continuous miner technology. Colliers & Associates, Inc. has found that over the past eight years too often foreign companies or countries purchase American continuous miner equipment without first conducting a thorough geologic, geotechnical and ground control study for the reserves to be mined. The problems are compounded by not developing mine plans, and submitting them to the regulatory authorities for approval prior to purchasing and even implementing the equipment.

Jan 1, 2001

By Liang Yin-Huai

In Fuxin Coal Mines, there are more than 20 million tons of coal buried under seasonal streams. The coal seams are mostly shallow. We have mined more then 50 mining blocks distributed in 5 coal mines. Their natural conditions are different, and the consequences are also more or less different. However, no stream-water-inrush accidents under regular mining conditions are the same. There were 3 exceptions. They were caused by unexpected roof caving which made valleys or alluvia subside as funnel-like cavities and let in inrush of stream flow. The key to our success in mining shallow under-stream coal seams, according to our analysis, is that valleys or alluvia subside gently and basically evenly with contractible tension fissures and that fissures both in valleys or alluvia and in rock seams are blocked up or sealed by cohesive deposits either from alluvia or rock. This paper treats: (1) some typical illustrations of mining shallow coal seams of different occurrences under streams of different sizes, flowing capacities and valley structures, (2) observations of the height of caved and fissured zones and subsidence of valleys or alluvia, (3) observations of underground water flow before, during, and after mining and the fluctuation with respect to stream flow, (4) observations and analyses of blocking up of fissures caused by mining, and (5) feasibility of mining shallow under-river coal seams.

Jan 1, 1990

By E. Bane Kroeger

In underground coal mining, there is often a need for supplemental support for mine openings. In the past, one of the most common types of supplemental support was wooden posts that were installed against the roof using opposing wooden wedges. Underground, wood has the tendency to shrink from moisture loss and dislodge if not under load. Another drawback to using wood is the variability in strength between posts. Defects in the wood such as knots can cause weaknesses that often lead to premature failure of supplemental support. Many mines that install large amounts of supplemental support in certain areas of the mine such as bleeder entries in longwall mining have switched to using steel props rather than wood posts or cribbing. The reactions of steel props under loading are well- defined and there is little variability in strength between props. Steel props and can be fabricated so they can be used in a variety of roof heights without modification. Wooden posts often have to be cut to a usable length underground before installation. This adds to the installation time of the wooden posts. Steel props are more compact and can be lighter than their wooden counterparts, depending on the length and carrying capacity. Often times it is desirable to prestress the supplemental support to improve roof stability. This is often problematic and time consuming with some types if supplemental support. With these factors in mind, research was undertaken at Southern Illinois University Carbondale (SIUC) to design a new steel roof prop. Several new clamping designs were developed and prototypes were fabricated and tested in the labs at SIUC in the spring of 2003. The designs were modified and refined and the first full-size prototype roof prop was tested in January 2004. With the success of the full-size prototypes, a cooperative research program was established between SIUC and Excel Mining Systems, Inc. to further develop the new prop. Development went smoothly and the prop has performed as expected. In February 2005, SIUC and Excel entered into an exclusive licensing agreement. The prop design under license, the K-Prop, will be installed using a lightweight portable hydraulic jacking system under design that can be used to prestress the props, applying load to the roof and floor during installation. By varying the installation load, the prestress load can be varied from about 1,000 to 10,000 pounds (4.448 to 44.48 kN) and at the same time, the carrying capacity of the K-Prop can be varied from 10,000 to 100,000 pounds (44.48 to 444.8 kN). The K- Prop is composed of only 3 pieces and laboratory testing has suggested that it can be installed by a pair of workers in less than two minutes. The speed of installation of the K-Prop should significantly reduce the total installed cost for supplemental support and should provide a safer working environment by prestressing the prop, which will add support load to the roof and floor during installation.

Jan 1, 2005

By J. K. Whyatt

A comprehensive survey of mine seismicity and rock bursting during development of two sublevels at the Lucky Friday Mine, Mullan, ID, USA, was conducted to better define rock failure mechanisms and sources of ground control hazards. Survey data included rock burst damage reports, seismic event locations and magnitudes and, for the most energetic events, first-motion information. Several subsets of this database, including large seismic events, rock bursts, and microseismic activity near the face, were analyzed. Elements of the large-event and rock burst data sets were nearly independent. That is, there was no relationship between the risk posed by a seismic event and its energy, although such a relationship is well established for the mine as a whole. All data sets showed that certain geologic features appear to control the spatial distribution of events and the spatial distribution of rock burst risk. The data also suggest that. within the scope of this study, the greatest risk of injury occurs when a pocket of heightened rock burst risk is first encountered and that this risk is controlled when miners adapt their practices to these conditions. Recognition of the role of particular geologic features in the spatial distribution of rock burst hazards provides an opportunity for anticipating, rather than only reacting to, a changing level of rock burst hazard. However, much work will be required to make good on this promise.

Jan 1, 1998

By D. W. H. Su

A two-year study was conducted by CONSOL in a northern West Virginia coal mine to evaluate pillar design and support requirements to improve roof control in right-hand longwall headgates subject to high in situ horizontal stresses. Horizontal stress measurements conducted within undisturbed areas of the subject mine revealed a pre-existing regional horizontal stress field with a significant difference in magnitude between the east-west maximum and the north-south minimum stresses. Three¬dimensional stress cells installed to monitor horizontal stress concentration in the headgate roof during mining revealed that a narrow (60-foot center) headgate pillar reduces the east-west horizontal stress concentration in the roof ahead of the face such that the headgate is more stable and requires less support. This 60 foot x 140-foot pillar design, which has been employed in subsequent panels, still provides adequate stress attenuation to protect future tailgates under a maximum cover depth of 1000 feet. Roof geology derived from underground roof reconnaissance and underground bolt load and roof displacement measurements confirmed the effectiveness of 12-foot long cable bolts for controlling the headgate roof subject to high horizontal stresses. With the new headgate pillar design and the supplemental cable bolts, headgate roof conditions in the subsequent panels improved significantly, longwall production delay due to adverse headgate roof condition was totally eliminated, and record coal production was achieved by the subject mine in the subsequent years.

Jan 1, 2003