Search Documents

By Danny J. Van Roosendaal

An investigation was undertaken to determine hydrogeological effects of subsidence over a longwall coal mine in the Illinois Basin. At this mine, approximately 200 ft of bedrock overburden is overlain by up to 150 ft of glacial till and localized water-bearing glacial sediments within a buried bedrock valley that overlies the longwall panel. A finite-element mechanical model of the subsided longwall panel shows sufficient strain to enhance permeability throughout the bedrock portion of the overburden. However, examination of the actual surface subsidence profile indicates that the overburden deformation is localized in narrow zones at the panel edges. The aquifer units at the base of the glacial sediments are confined by glacial clays (above) and weathered shales (below). Elevated water levels were observed in the glacial aquifers during subsidence, which indicates that the clays and shales maintained confinement as the overburden subsided and deformed. A three-dimensional ground-water flow model was used to simulate the effects of subsidence on the hydrogeologic system and to estimate inflows into the mine. Longwall retreat was simulated by several model runs, each representing a new longwall face position. Simulated heads and mine inflows were calibrated with recorded water levels and observed inflow conditions by modifying the hydraulic conductivity of particular model layers. Model calibration indicates that the permeability of certain lithologies, such as plastic underclays and weathered shales, is not significantly enhanced by subsidence. A worst-case scenario was simulated by inserting a deeply incised, sandfilled valley into the model, which had only minimal impact on the simulated mine inflows.

Jan 1, 1995

By P. K. Kaiser

The purpose of deformation monitoring for the evaluation of the stability of underground openings is reviewed briefly and some results from laboratory tests of small tunnels are presented. The ground behaviour is described by comparison with the response of structural systems and illustrated by the data from the testing of small tunnels. It is concluded that the main objective of a deformation monitoring system for stability evaluation is to determine the actual process of deformation and instability in the area surrounding the opening. Only when this process has been established is it possible to use deformation measurements to design support systems or to improve construction or mining procedures. Present monitoring practice is not sufficiently orientated toward the aim of process description.

Jan 1, 1981

By Shosei Serata

Serious floor heave of up to 2.4 m in a 2.4-m high mine entry was eliminated by applying the stress control method of mining, as a last resort, at the No. 5 coal mine of Jim Walter Resources, Inc., in the Black Warrior coal basin near Birmingham. Alabama. Underground observation of the first 3-room entry created using the stress control method is discussed here. The behavior of the test entry, which eliminated the heave problem, is analyzed in relation to similar studies conducted in a salt mine under similar ground conditions by utilizing finite element analysis.

Jan 1, 1984

By Stephen P. Signer

A method to assist in the evaluation and selection of roof bolts using in situ measurements of roof bolt loading has been developed by researchers of the Spokane Research Center, National Institute of Occupational Safety and Health. Both axial and bending forces are measured by strain gauges at many locations along the length of fully grouted bolts during various stages of mining. This information is then used to ( I) predict bolt loading for variations in bolt spacing, grade, and diameter, (2) calculate the design changes necessary in zones where bending loads are high, and (3) determine if bolt length is adequate. Results from several case studies of full-column bolt loading in coal mine gate roads are used to illustrate the design method. This knowledge will give design engineers a tool for the selection of roof support systems that will improve underground safety by reducing roof bolt failures.

Jan 1, 1997

By Yunqing Zhang

The 3-D numerical modeling using ABAQUS is performed to analyze the mechanisms of the tensioned bolts by taking into considerations excavation sequence, pre-tension, bedding planes and in-situ horizontal stresses. The effect of the pre-tension and the mechanisms of the tensioned bolts are analyzed based on the results from the modeling. Based on field observations, the failure modes for the tensioned bolted strata are classified by their causes and failure mechanisms. The support design consideration for each failure mode is given. Finally, a new design approach is proposed to do the tensioned bolting design using numerical method.

Jan 1, 2002

By C. C. White

Much benefit can be achieved by a mining company and a manufacturer if both parties can communicate effectively with each other and assist in product development; mutually beneficial ideas and products will develop. This communication can best be achieved if both parties have the opportunity of having on their respective staffs, specialists whose function is to improve the use of products used in mine development. Although a great wealth of roof control knowledge has long existed among mine operators, until recently there was not an abundance of joint development of roof control material by manufacturers and mine operators. This was perhaps due, in past lean years, to the preoccupation of mine management with other overwhelming problems that arise in mining. Manage¬ment had little time for the lengthy process of product development. Until recently, only a few of the largest mining companies had fulltime personnel devoted to roof control. A bolt manufacturer who is invited to work with an operator's roof control people in developing new material is lucky indeed in that he learns what is wanted and he acquires the benefit of the operator's knowledge and experience. He has only to come up with a satisfactory product at an acceptable price - which is not always easy: The development of new products is usually costly and time consuming, and many new products fall by the wayside. In the case of point anchors, however, this product is here to stay. The advantage of point anchors over mechanical anchors is now a proven fact. This advantage is due to less bleed off and higher ultimate load capacity of the resin point anchors. Point anchored bolts have proven to be superior to fully grouted bolts in many areas. We at Birmingham Bolt Company are fortunate in that we have been involved in joint efforts to develop point anchors with several coal companies from whom excellent advice and direction was received. It is appropriate to mention before continuing that the use of point anchors began in the 1960's in Europe and became widespread only recently in the United States. They fall in two categories, point anchors and combination point anchors. These categories have been defined by the Bureau of Mines as follows: (1) point anchors having 24" of grouted length and (2) combination anchors having 24" or more of grouted length. In the present nomenclature, all are anchored with resin or some sort of cementing compound between the rebar or tensioned element and the wall of the hole. The latest development includes an expansion shell as well as rebar, the purpose of the expansion shell being to facilitate installation without the delay necessary in use of types that require a waiting periond for setting of the resin before tightening. (See figures #1 and #2.

Jan 1, 1982

By Karl H. Brandt

In the Auguste Victoria mine a bolted rectangular roadway has been kept open for the first time in the seam D/C after retreat. The target of the project was to gain a basis for planning and experience for future mining layouts in the same scam in view of the reuse of boated rectangular roadways. For this the roadway was additionally secured in sections with longbolts before the influence of the retreating panel had taken place. On retreat a concrete sidepack was concurrently put in place on the face side. The installed monitoring systems consisted of endoscopic devices, multiple extensometers (Tell-Tales), shear-tales, extensometers and convergence measurements. The experience that was gained was carried over into a physical and numerical model.

Jan 1, 2001

By Baisheng Zhang

The definition of Ultra-close multiple seams as defined by the floor disturbance depth, h, due to mining in the upper seam is proposed: it refers to those coal seams that are spaced very closely, i.e. h,, the distance between seams, is small or equal to h, , and mining of any one of the seams will significantly affect the others. Those seams are called the ultra-close multiple seam group. Theoretical formula for defining it and practical examples are given in this paper. Underground measurements and numerical analysis show that in ultra-close multiple seam mining, the characteristics of ground pressure due to lower seam mining is different from that of single seam mining. The major differences is that the roof, as a result of damaged caused by the upper seam mining, is full of factures; the roof broke up in the belt entry and fell down easily; support loading at the face was small without clear periodic weighting phenomenon. Based on these results the roof structure model and roof control theory for ultra-close multiple-seam are established.

Jan 1, 2005

By Leo L. Van Sambeek

Specification of properly sized pillars to support the overburden is one of the most challenging aspects of salt mine design. Interest in salt pillar design is heightened by the recent flooding of the Retsof salt mine, water inflows to the K2 potash mine, and closing of the Belle Isle salt mine because of ground control problems. A series of numerical modeling analyses show that a simple pillar design equation for salt pillars adequately reproduces results of extensive modeling efforts. The paper describes (1) the basis for the pillar design equation, (2) equation verification by comparison with numerical modeling results, and (3) equation validation by comparison with measurements and observations of salt pillar behavior.

Jan 1, 1997

By Richard C. Repsher

The U.S. Bureau of Mines has developed a method and device designed to detect lose rock material in underground mines. The technology is designed to be an aid to mine workers in detecting hazardous roof conditions in underground mines which can complement or replace the traditional roof sounding techniques where the miner relies on experience to determine whether rock conditions are sound. The leading cause of accidents and fatalities in underground mines is falls of lose rock pieces or rock slabs from the mine roof. The device is an electronic roof sounding device that acoustically determines the integrity of mine rock. In previous research the Bureau of Mines found that loose rock, when impacted, vibrates at a much lower frequency than intact rock material. A major problem in determining rock stability using this technique has been the repeatability of the matt signal. This difficulty baa been greatly reduced in the current design by measuring the power spectra contained in two separate frequency bands of the signal produced by striking the rock in question. The ratio of the energy contained in each band is computed. This process minimizes any striking force differences, producing accurate, repeatable results for solid rock as well as loose, drummy material. The prototype has been successfully- tested in a variety of underground environments including coal, uranium, molybdenum, silver and salt. The technology has been investigated by the U.S. Mine Health and Safety Administration and the Department of Energy for use in detecting detached tunnel lining areas in nuclear repositories. The paper will discuss the technique, applicable results, and future applications.

Jan 1, 1990

By Jinsheng Chen

To maintain the stability of longwall tailgate entries, they have to be supported by not only the primary roof support but also the secondary roof support due to the impact of the longwall mining¬induced abutment loads. Depending on the mining condition of a typical coal seam and its distance from the previous panel's gob, the longwall tailgate entry is often reinforced by the secondary roof support in the form of standing supports and/or cable bolts or trusses during longwall retreat, Even though lots of research work has been done to study the behavior of different standing supports in the laboratory. their function and requirements for a typical mining condition are still not fully understood due to lack of field data and correct assumptions about the behavior of the already-bolted entry roof under mining-induced abutment loads. Therefore, the application of the secondary roof support for tailgate entry roof control is still limited to trial and error, which often results in either higher cost for tailgate roof control if the design is too conservative or more production delays due to roof falls in the outby tailgate entry if the design is inadequate. To have a better tailgate roof control with reasonable roof control cost, RAG American Coal, NIOSH, and HeiTech have been conducting a joint research project to monitor actual roof loading, roof deformation, and entry convergence in the tailgate entry of 10 North panel at RAG Emerald mine. The actual roof loading data are used to calibrate and improve the roof control model for longwall tailgate entries, which has been developed by RAG American Coal, and to further reduce the roof control cost for longwall tailgate entries. The authors in this study attempt to discuss the Roof Control Model developed by RAG American Coal. in which some guidelines or important parameters for designing the secondary roof support for longwall tailgate entries are proposed.

Jan 1, 2003

By Tom Denton

The bolt design criteria, since it was first published by Dr. John Stankus (Stankus, 1997), has been recognized as an important tool in ground control design. This concept is based on the Optimum Beam Building Effect (OBE), which is defined as the roof beam that has no separation above or within the bolted range and having the shortest bolt possible. This paper will present an application of this concept at the American Coal Company. Galatia mine. This mine previously used a 6' and 7' length bolt. However, since seam thickness has gotten smaller in the Southern area of the nine, a two-piece bolt is required. A two-piece bolt increases ground control costs and delays production. Therefore, a one-piece, shorter bolt, if feasible, can reduce costs and expedite development. In this analysis, Computer modeling is first conducted to determine bolt length and installed load. Second, a special bolt is developed, that can achieve the proper installed load as determined by the computer modeling. Third, underground bolt pull and load cell tests were conducted to evaluate bolt performance. Finally, an underground "bench" test was conducted. The test results have shown that entry convergence in the short bolt (5) test area is less than the 6' bolt area. Overall roof condition in the test area was as good as the 6' bolt area. Based on this analysis, the mine has converted to a shorter bolt in the low seam area and it is working well.

Jan 1, 2000

By Hideki Shimada

In underground coal mines, grouting method is employed in order to reinforce the floor and to control the movement of groundwater into the roadway. However, the seepage and the reinforcement behavior of the grouting material into the floor are not clearly understood. Therefore, grouting is today normally based on empirical relationships and on the experience of the grouting personnel. To assist grouting projects, it must be acknowledged that many of the flow and the hardening processes occurring during grouting so far defy mathematically analysis. From this point of view. this paper discusses the behavior of grouting material, when it is injected into the roadway floor, by means of 3-D Eulerian-Lagragian seepage analysis. Moreover, the effectiveness of reinforcement grouting on the mechanical properties of slaking-prone mine tunnel floor are studied by means of several laboratory tests. Keywords: Mine tunnel floor, Grout, Seepage, Reinforcement

Jan 1, 2002

By Kot F. Unrug

The shale response to moisture changes and the major finding of the appropriate research concerning this subject are briefly reported in this paper. Also described are mine ambient atmospheric conditions which are responsible for moisture changes in mines. The need for a quantitative measure of the weathering potential of roof. rock is demonstrated in relation to its influence on safety and the potential for increasing the cost of mine operations. The weatherability test presented in this paper has been developed and used in many mines. It imitates the natural process in a mine by subjecting the rock sample to alternating wet and dry cycles. The natural changes are thus accelerated, but are similar to the natural conditions to which the surrounding excavation rock will be exposed. The measure of the weatherability index is the percentage of the initial sample mass remaining after the test as the largest fragment of the sample. Thus, the index changes, from 100% for rock affected by moisture changes which disintegrates completely, to 0% for rock totally unaffected. In this paper, the apparatus and testing procedures are described. Also presented are examples of test results. with a discussion of the design implication to he considered by mine planners.

Jan 1, 1997

By Tim Ross

Slurry injection into mined-out panels is an attractive alternative for disposal of coal preparation plant fines. however, in areas where surface subsidence cannot be tolerated, either by law or necessity to protect surface structures or aquifers, special consideration trust he given to the effect of slurry injection on panel stability. Slurry injection can lead to panel failure and unplanned subsidence by degrading roof, pillar, and floor strength. Water degradation is of particular concern where clay is present in the floor. Recently. unplanned subsidence related to slurry injection occurred at an Indiana room-and-pillar coal mine subject to weak floor conditions. This paper discusses the efforts of the mine operator to determine the causes of the panel failure and to design panels and injection procedures to allow for future economic slurry injection without subsidence. The numerical and empirical/analytical techniques applied give the operator a rational approach to pillar panel design for future injection panels under various cover depths and weak floor conditions.

Jan 1, 1998

By Mikko Ahola

This paper describes recent innovative analyses conducted by the Bureau of Mines to demonstrate the application of the boundary-element method in evaluating the effectiveness of caving chambers or sacrificial entries to relieve the stress conditions initiating cutter roof failure in underground coal mines. The analysis assumes that cutter roof failure results when the shear strength of the roof rock at an entry corner is exceeded by the applied shear stress. The applied shear stress is due to large differences between the horizontal and vertical in situ stresses known to exist in many coal mining districts experiencing cutter roof failure. The results of boundary-element analysis suggest that driving an arched lead entry in advance of adjacent rectangular entries and allowing it to cave significantly reduces the difference between the principal stresses at the corner of the rectangular entry, thereby lowering the maximum shear stress. Slippage of the immediate roof along horizontal bedding planes into the caved entry is shown to further reduce the stress conditions in adjacent entries. Practical applications of this stress control technique to longwall and room-and-pillar mining are discussed.

Jan 1, 1987

By Kevin M. Connor, O&apos

An example application is presented in which Time Domain Reflectometry (TDR) was utilized to monitor roof strata movements during pillar extraction in a potash mine. The study was initiated when Western Ag-Minerals decided to implement secondary mining of pillars in order to extend the life of their Nash Draw Mine. A prototype operation was conducted in one mine panel to assess mining equipment and procedures, and to determine if ground control problems would develop. An instrumentation array was installed by personnel from New Mexico Tech and Western Ag to monitor strata movements, changes in pillar stress and surface subsidence, and these data are being analyzed by the Bureau of Mines. This paper is limited to a discussion of roof-floor convergence and roof strata movement to illustrate the application of TDR to ground control. Plots are presented which demonstrate the capability of distinguishing location, magnitude and mode of rock movement using TDR to interrogate coaxial cables grouted into holes drilled in the roof.

Jan 1, 1990

By Gift Makusha

The Witbank Coalfield in South Africa contains up to five economically viable coal seams. These seams have been mined continuously for over 100 years and the reserve in now becoming depleted. The normal mining method has been bord and pillar with examples of stooping. The situation now occurs where the formed pillars, left to maintain stability, have a higher quality than the coal that is left in the unmined reserves. Where the reserves are less than 70m deep and continuous over several kilometers, opencast mining is being successfully applied. After several years of investigation, Anglo Coal has identified blocks of coal that warrant investigation with regard to pillar extraction by underground methods The proposed method is pillar extraction using Mobile Roof Supports (MRS) It is proposed to mine three panels at a depth of 120m, by keeping the panels narrow and sub-critical. The sub-critical layout does not allow caving to surface and more stress is thrown onto the barrier pillar rather than the face pillars. The sub-critical span is anticipated to be 100m. The paper describes the full geotechnical investigation, including numerical modelling, instrumentation and drawing on the local South African experience of shortwall mining. The project will be unique in that pillars were not designed for pillar extraction and have low factors of safety (l.4 - 1.8) and width to height ratios of less than 4. The mining height will be approximately 4-4 5m, and this represents "new" operating heights for Mining Roof Supports. The required equipment was ordered in late 2002 and pillar extraction is anticipated to begin in June 2003.

Jan 1, 2003

By Stanislaw Prusek

In this paper, results of underground measurements conducted in gateroad 3, seam 615, at the Bobrek-Centrum Colliery are presented. The Bobrek-Centrum Colliery is owned by Kompania Weglowa, the largest hard coal producer in the European Union. Yearly production at the colliery, including the longwall system, is about 2 million tonnes. Gateroad 3 was used simultaneously for two retreating longwall faces, No. 1 and No. 2. This working was also employed for the conveyor belt for longwall No. 1 and served as a transport road for longwall No. 2. Approximately 100 meters of gateroad 3 was maintained behind the face of longwall No.1 and then, with the progress of longwall No. 2, it was liquidated. In this paper, we present the results of underground measurements of vertical and horizontal convergence in gateroad 3. We also present the results of numerical modeling for deformation of the working. Finally, we analyse the accuracy of the numerical calculations by comparing them to the actual deformation of gateroad 3.

Jan 1, 2014

By Michael J. Friedel

The fundamental problems associated with ground control reflect the inability of mining personnel to "see" the development of anomalous conditions. Toward this end, the U. S. Bureau of Mines is investigating the application of seismic refraction tomography for imaging the process of pillar yielding, at the Foidel Creek coal mine, near Steamboat Springs, CO. The inherent three-dimensional problem of imaging coal pillar stress is reduced to a single plane by considering only the stress transmitted from the pillar to the adjacent floor rock. This approach exploits the fact that refracted seismic energy is essentially confined to the adjacent higher velocity sandstone strata. The tomographic analysis using ray-tracing based on wavefront migration resulted in a robust P-wave tomogram from which regions of high velocity indicate zones of high stress concentration, whereas low velocity zones indicate regions of stress relief. The interpreted region of high stress concentration occurs at the pillar end nearest to the working face of the adjacent longwall panel. This finding is corroborated by vertical pressure cell measurements recorded in the pillar. The stress diminishes toward the pillar perimeter with local minima correlating to the locations of observed pillar spalling. Time-sequence monitoring, as the longwall face advances, is recommended for evaluating changing stress conditions.

Jan 1, 1993