Search Documents

By James D. Pile

Following a methane ignition in the active panel of a longwall coal mine, the affected panel was successfully isolated from the rest of the mine. This allowed for the remainder of the mine to return to regular operation, and the conventional practice of having to seal the portals for a defined period of time was avoided. After the affected panel had remained isolated for a regulatorily mandated period of time, it was reopened in preparation for longwall face recovery. As it was not possible to move the shields from their existing positions to facilitate the installation of recovery mesh prior to shield recovery, alternative methods had to be considered to stabilise the gob and minimise flushing, thereby improving operator safety. The objective of the paper is to show how stabilisation of the gob was achieved during shield recovery, thereby minimising flushing, and improving operator safety. Phenolic foam was chosen and injected from between the shields into the gob behind them. This is a technique that has been used to great effect in Germany, to a lesser extent in Australia, but not knowingly to date in the United States. To ensure nothing was left to chance and thereby guarantee the project?s success, the procedure used in Germany was employed, down to the application of equivalent hardware, which was sourced through the North American supplier.

Jan 1, 2013

By Frank E. Chase

Clay veins, also referred to as clay elastic dikes, have been responsible for numerous underground injuries and fatalities. These hazardous structures are also responsible for increased production costs during all phases of mining. For these reasons, the Bureau of Nines has investigated the physical characteristics of and roof instability problems associated with clay veins in order to make support and other mining recommendations. In addition the occurrence and origins of clay veins were examined to determine whether or not the structures could be projected into unmined portions of the coalbed. This investigation included portions of the Arkoma, Illinois, Northern Appalachian, Southern Appalachian, and Uarrior Coal Basins. Virtually a11 clay veins observed or documented occurred in the Illinois and Northern Appalachian Basins. Observed clay veins ranged in sire from 1 inch to 16 feet In cross-section and were found under shale, siltstone, sandstone, and limestone roof rock. Individual clay veins were predominantly composed of claystone; however, limestone. siltstone. and sandstone infilled clay veins do occur. Clay vein formation has been associated with the infilling of fissures which result from compressive, tensile, or shear ground failures. These gaping fissures were propagated by compactional processes and/or tectonic stresses active during and subsequent to coal iff cation. Associated fault, fracture, and slickenside planes commonly parallel clay veins and disrupt the lateral continuity of the immediate and, sometimes, main roof. When clay veins parallel or subparallel the direction of face advance the roof is segmented into cantilever beams causing unstable conditions. Therefore, the strata on either side of the clay vein must be bolted and strapped together to form a beam.

Jan 1, 1984

By Kazem Oraee, Mehran Gholincjad, Navid Hosseini

"Chain coal pillars are pans of the structure of longwall mining system that play a significant role in the stability of the entries. With mechanization and developments in the various aspects of the method, higher efficiency in optimization of the design of chain coal pillars seems appropriate. In this paper the three main methods of chain pillar design, namely the empirical analytical and numerical methods arc compared. Real data from the Tabaslran coal mines have been used in order to make the comparison process reliable. It is concluded that the most apparent advantage of the empirical method is the reliability of the results while the use of numerical methods enjoys the advantage of flexibility. On the other hand the analytical methods are complex unless simplifying assumptions arc made that can substantially decrease the accuracy of result which is thought to be the main advantage of the design method. A new method is therefore introduced here that combines all of the three presently used methods and by doing so the new method has the advantages of the three while minimizing complexities and inaccuracies associated with the use of the individual methods.INTRODUCTIONLongwall mining is a high production method that can use mechanization to its full extent. Its initial development can be traced to 17th century European collieries but it was not until the second half of the 20th century with the development of self advancing support systems that the method gained popularity in the USA (Oraec. 2001). During the last decade, the production of longwall faces has increased significantly (Peng. 2006). The ability for mechanization along with good safety condition is the main reasons for such development. In the longwall mining method a good design for panel and entries on both sides, are two essential parameters. In this method, the thickness of overburden (depth of mine) nom1ally ranges from 60 to 20 m (197 to 2.7 9 ft) (Hartman, 2000) and with increasing mine depth designing for stabilizing the entries on both sides of the panel become more difficult. Thus, for safety and stability the size of chain pillar must increase. This causes the overall coal recovery to decrease and increase mining costs per ton. As such wide pillars hinder the air flow and hence ventilation costs increases too. Therefore with accurate identification of loading conditions and stress analysis. pillar that are a minimum size and sufficient safety factor are carefully designed."

Jan 1, 2010

By Fernando O. L. Xavier

"The Barro Branco coal mine was located in the southern region of Brazil, in the state of Santa Catarina. In 2002, an incident occurred at the mine, leading to a violent, massive pillar failure, resulting in almost 100 failed pillars in less than 3 hours, totaling nearly 700 collapsed pillars after a period of 6 weeks. The paper outlines the geological and operational conditions before the accident and analyzes the primary factors leading up to the event. This paper also discusses and examines the unusual characteristic of violent, uncontrolled pillar bursts that occur over a longer timespan, in comparison to other equally violent but rapid events, such as those that occurred at the Crandall Canyon Mine, at a Book Cliffs District mine, and at the Solvay Mine. INTRODUCTION The southern region of Brazil holds 100% of the coal reserves for the country, and half of it is located within the state of Santa Catarina. Almost the entire Brazil’s coal production, around 8 million tonnes/year, is consumed for electricity generation. Most of the coal mines in Santa Catarina are underground room-and-pillar mines, and most are shallow mines, with depths of cover ranging from 20 to 400 m. The Barro Branco mine, near the city of Criciuma, experienced a violent mine collapse at the end of March 2003, which was analyzed and discussed by Zingano, Koppe, and Costa (2004). The event consisted of violent failure of 100 pillars in less than 3 hours, and a subsequent failure of approximately 700 additional pillars over the next 6 weeks. After the panel collapsed, the mine was closed due to unsafe conditions as a consequence of the seismic event. A map of the collapsed area is shown in Figure 1. GEOLOGY AND MINING METHOD There are two coal seams mined at Barro Branco mine. The first is the 1.5 m to 2.3 m thick Barro Branco Seam, under about 75 m of cover. The second is the Bonito Seam, where the collapse occurred. The Bonito Seam is 2.5 to 5.5 m thick located at a depth of approximately 80 m, with an average dip of 0° to 15°. Various major faults and inherent joints are present in the area."

Jan 1, 2017

By Andrew Hyett

Over the last 30 years, a transition away from end-anchored bolts to fully grouted rock bolt systems has occurred in many underground mines. It seems geomechanically intuitive that the success of such bolts, which interfere with rock movements around underground excavations through a variety of complex interactions, is precisely why they remain challenging to instrument and monitor. Whereas measuring the load profile for an end-anchored mechanical bolt is trivial, for a fully grouted system, the load may vary dramatically due to discrete rock movement at cracks and joints. Despite the challenges, measuring the strain (i.e., load) along fully grouted rock bolts remains very appealing, and a lot of valuable research has been conducted using foil resistance strain gauges, particularly in US coal mines (Signer and Jones, 1990). Despite good intentions, more widespread adoption of this instrumentation remains unlikely for the following reasons: (i) The technology is expensive, partly because Intrinsically Safe (IS) requirements limit the number of suppliers and solutions. (ii) The technology is perceived as challenging to successfully implement except by those who are skilled in the art. (iii) The reliability of the technology is questionable in harsh environments. (iv) The technology relies on discrete pairs of strain gauges that may not capture the complete strain distribution along the bolt. No existing alternative technology can offer a solution to all of these limitations. However, in this paper, we introduce results from a new Distributed Optical Sensing technology that promises significant potential. Since the technology is capable of distributed sensing, our results suggest that this new technology can, for the first time, reveal the detailed strain profile along fully grouted rock bolts.

Jan 1, 2013

By Dennis R. Dolinar

Controlling coal mine roofs subjected to high-horizontal stress conditions has always been difficult and uncertain. Traditional supports such as wooden cribs and posts, concrete donut cribs, and standing supports collapse and fail when the roof and floor move horizontally as mining progresses. The former U.S. Bureau of Mines (USBM) (currently the U.S. Department of Energy (DOE)), in cooperation with Western Fuels-Utah, Incorporated, conducted research to provide an alternative for traditional secondary support systems in a 3-entry gate road system subjected to high horizontal movements. The support system used in several other coal mine operations, consisted of internal high-strength galvanized resin-grouted cable supports. The system virtually eliminates the necessity for external crib, timber, or concrete supports. The support system consisted of 2.4 m (8 ft) full-column resin grouted bolts and 4.8 m (16 ft) long cable supports installed in conjunction with wire mesh and "Monster-Mats." Cable loading and roof deformations were monitored to evaluate the behavior of the immediate and main roofs during first and second panel extractions. Additionally, cable trusses were installed on the longwall headgate to protect the coal conveyance system from roof and pillar falls created by the formation of cutters and gutters. The test results indicated that the designed support system successfully maintained the roof during the extraction of two longwall panels and dramatically reduced the cost of secondary support. This paper describes the theory of high-horizontal roof movements, the advantages of vertical cable supports and cable trusses, and presents the roof and cable measurements made to assess the support performance during longwall retreat mining.

Jan 1, 1996

By Jessica M. Wempen

Differential Interferometric Synthetic Aperture Radar (DInSAR), a satellite-based remote sensing technique, has been demonstrated as a potentially practical method for measuring mining induced surface subsidence. Unlike traditional methods of subsidence monitoring, DInSAR has the capacity to generate subsidence data on a regional mining scale with a relatively high data density. Using DInSAR to evaluate subsidence over large regions with relatively long time scales has the potential to help quantify the impact of subsidence in the mining region, and provide a means for validating whole-mine geotechnical models. In this study, nine pairs of interferometric data from the Japanese Advance Land Observing Satellite (ALOS) were processed using DInSAR to generate displacement maps for a group of trona mines in southwest Wyoming. The data cover a time span from December 2007 to March 2011. The maximum subsidence for one of the mines totaled 1.3 meters for this period. Cumulative DInSAR displacement maps show the development of subsidence over time. In this mining region, surface subsidence is generated primarily by extraction of trona using retreating longwalls. Additionally, trona is extracted by solution mining, which also generates measurable surface subsidence.

Jan 1, 2014

By Amirhossein Molavi Tabrizi

In this paper we introduce a realistic model for mine openings that explicitly considers the effects of local irregular topography. Also, we consider the effect of entry orientation and rock anisotropy on the induced stress fields around mine openings under the given in-situ stress field. A triangular mesh formulation is derived for representing complicated irregular surface topography and underground openings. Each element contains three internal collocation nodes. Parts of the surface which are far from the mine openings are discretized by infinite elements. The rectangular infinite elements with three internal nodes are introduced specifically for this problem so they are compatible with the triangular elements. With the corresponding boundary element method (BEM) formulation, we then investigate the combined effect of the topography and entry orientation on the stress fields induced by openings in anisotropic rocks under in-situ stresses. A single rectangular opening in the anisotropic ground with topography and in-situ stresses is simulated using data from the Carroll Hollow mine in Ohio. The results of these simulations show that topography, rock anisotropy, orientation of the regional stress field and mine opening geometry all have appreciable effects on the stress fields around underground openings, yet these factors can all be accounted for in an efficient code with no need to discretize the model domain. Future applications using this new BEM formulation will provide useful guidance on selecting the optimal opening orientation in the mine in order to minimize undesirable stress concentrations around underground mine workings.

Jan 1, 2014

By Kevin W. Harris

Multiple-seam coal mining is a major issue in underground coal mining that adds additional complexity to the practice of ground control. As reserve exploitation is driven by economics, it is now difficult to mine coal without the existence of previous workings above and/or below the active seam; this is particularly true in the Appalachian coalfields. The frequency in which problematic multiple-seam interactions are now encountered has resulted in significant research regarding the underlying mechanisms of the problems and methods of mitigation. In the last few decades, a great deal has been learned about these interactions and the ability to minimize problems associated with these hazards has greatly advanced, resulting in better economics and improved safety. Minimizing the adverse effects of stress interactions often requires a thorough understanding of site-specific geotechnical parameters and previous mining geometry. This is especially evident in bump-prone ground, where pillar behavior is highly dependent on local conditions. This paper presents a case study in a deep cover, Central Appalachian coal mine where three bump events occurred. Initially, empirical design software was used in an effort to analyze the situation and prevent further instability. The empirical study proved ineffective. A detailed investigation of the bump events using the boundary element software LaModel 3.0 was then performed. This study resulted in a site-specific calibration standard that will be applied in numerical pillar design for the remaining reserve.

Jan 1, 2014

By Mostafa Sharifzadeh, Ebrahim Ghasemi, Kourosh Shahriar

"The Tabas Central Mine (TCM) is one of the underground coal mines located in the Tabas coal region, in the mid-eastern part of Iran. This mine is the first mechanized coal mine in Iran that uses the room and pillar method. Pillar design is one of the most important issues in underground coal mines, especially in room and pillar mining. In this paper, a new method for coal pillar design in the main panel of TCM is presented. This method is able to estimate the magnitude of the various loads (both development and abutment loads) that pillars might experience throughout the mining process. Also, the method reduces the pillar failure risk. Based on this method, proper pillar sizes in TCM are obtained (11.6 x 11.6 m (38.l x 38.1 ft)).INTRODUCTIONPillar design and stability are two of the most complicated and extensive mining problems related to rock mechanics and ground control subjects. Although these problems have been investigated for a long time, to date only a limited understanding of the subject has been gained. Prior to this, the dimensions of a pillar were largely determined by experience based on trial and error, intuition, or established rules of thumb; any research available tended to be isolated and sporadic. But nowadays, various pillar design formulas have been developed based upon laboratory testing, fullscale pillar testing, and back-analysis of failed and successful case histqries. In 1980, a number of ambitious field studies conducted by the U.S. Bureau of Mines developed the ""classic"" pillar design methodology. It consisted of three steps (Mark, 1999, 2006):1. Estimating the pillar load using tributary area theory2. Estimating the pillar strength using a pillar strength formula3. Calculating the pillar safety factorAlso, Bieniawski (1981) presented a step-by-step method to determine coal pillar dimensions in room and pillar mines. In this method, similar to the classic method, pillar load is estimated by using tributary area theory.Currently, in mqst of the room and pillar mines, remnant pillars in panels are recovered by retreat mining (pillar recovery). Hence, the above mentioned methods are not appropriate for pillar design, because in these methods pillar load is estimated by the tributary area theory, and the effects of abutment loads, which result from retreat mining and the creation of a mined out gob, are ignored. Abutment loads affect the pillars in the adjacent of pillar line and a load greater than what is estimated by tributary area theory is applied on the pillar. So, pillar design without considering the abutment loads leads to pillar failures during retreat mining. Pillar failures continue to be one of the greatest single hazards faced by underground coal miners. Pillar failures are responsible for unsatisfactory conditions, which include the following (Mark et al., 2003):"

Jan 1, 2010

By Kristine L. Pankow, Keith D. Koper, Michael K. McCarter, Jared R. Stein

"The Wasatch Plateau region of central Utah contains a number of active underground coal mines in an area of well-documented natural seismicity. As a result, there are several hundred seismic events recorded in this region every year that may or may not be attributed directly to mining activity. Previous studies have linked the majority of this seismicity to mining activity through various means, but have not attempted to develop a method for categorizing individual events within a seismicity catalog. This study uses both relative relocation and waveform cross-correlation to separate events based on hypocentral depth and waveform similarity, respectively, in the area surrounding a single longwall coal mine within the Wasatch Plateau. We conclude that relative relocation can help with depth discrimination, but there are some unavoidable limitations caused by sparse seismic network coverage. The cross-correlation technique is more promising, with the ability to group events by waveform similarity and track mining progress over both space and time. With cross-correlation based clustering, we confirm that the vast majority (97.6%) of events in the study area are directly related to mining activity, but that a small population of natural seismicity is present as well. Eliminating this natural seismicity from the catalog of seismic events, leaving only those events related to mining, can give operators valuable information about the changing conditions as mining progresses and eliminate concern over events unrelated to mining activity.INTRODUCTIONA number of underground coal mines are located in the Wasatch Plateau region of central Utah, and have been in operation since the late 1800s. This activity has resulted in a well-known history of mining induced seismicity (MIS) (Wong, 1985). Additionally, this area is situated near the border of the Basin and Range and Colorado Plateau physiographic provinces, where naturally occurring tectonic earthquakes also occur (Arabasz et al, 1980). Seismicity separating these physiographic provinces is part of a larger band of seismic activity known as the Intermountain Seismic Belt (ISB) that runs from Montana to Arizona and cuts through the western boundary of the central Utah coalfields (Smith and Arabasz, 1991) (Figure 1)."

Jan 1, 2015

By Andre Cezar Zingano

"The objective of this paper is to estimate the coal seam strength and the pillar safety factor for low coal seams using back analysis and rock mass characterization. The coal seam strength is very important to estimate both pillar capacity and mine section design. There are two approaches to estimating coal seam strength: (i) by geomechanics characterization of the boreholes cores; and (ii) by back analysis from pillars successes and failures, or some in-situ tests. For low coal seams (1.2 m, or 47 in.), the confinement of the center of the pillar is very important to defining global pillar strength because the low seam height increases the confinement of the pillar core, even in small pillars. We used in this case study one underground coal mine in the Parana State where the coal seam thickness is 0.8m the pillar height is 1.3m, the entry width is 5m and seam depth is 130m. A panel test was prepared to study the pillar behavior for use of the retreat mining method. The designed pillar size was 6x5m and 1.3m high with a predicted safety factor of 1.0 based on the Hoek and Brown failure criterion is 5.3 MPa. Once no pillar failure was observed, the pillar safety factor was assumed at 1.0 and the coal seam strength was backcalculated. The back analysis estimated the coal seam strength to be 6.2MPa. The confinement of the pillar center directly affects the coal pillar strength, and also the coal seam strength estimated by back calculation.IntroductionThe coal seam strength is very important to estimating pillar strength and mine section design. There are two approaches to estimating coal seam strength: (i) by geomechanics characterization of the coal seam using borehole cores; and (ii) by back analysis from pillar successes and failures, or some in-situ tests like panel test or ultimate pillar capacity (Salamon and Munro, 1967; Maleki, 1981; Peng and Dutta, 1992). For the first approach, lab tests (mainly triaxial tests) and borehole geomechanics descriptions (quality and quantity of the discontinuities) determine the coal seam strength by the Hoek and Brown failure criterion (Hoek and Brown, 1997). For the second approach, a panel test to study the pillar behavior can be built to define coal seam strength by back calculation. The safety factor for the pillars in the test is 1.0, based on the estimated coal strength from the geomechanics characterization. In this case, the probability of failure is 50%. If some pillar failure occurred, and the real pillar size was measured, the back analysis could be applied to define pillar strength and the coal seam strength."

Jan 1, 2015

By Soheil Bahrampour

Development of measurement while drilling (MWD) systems for ground control applications in mining applications has recently been an active research topic. The main goal is to utilize the drilling information for characterizing the ground condition. Such characterization is the key to the accurate and efficient mapping of hazards and proper planning of ground support. However, most of the existing drilling units and measurement while drilling systems are mainly developed for joints and voids detection, and much less research is done to estimate rock strength. This paper focuses on rock classification based on estimated strength from the drilling data. For this purpose, data from J.H. Fletcher roof bolters instrumented with the vibration and acoustic sensors as well as torque, thrust, penetration rate, RPM and position signals is used. All the available data was utilized for rock classification using pattern recognition algorithms. The algorithms were developed based on data from drilling, and into three different rock types. The classification is performed using a simple feature extraction algorithm with a well-known pattern recognition algorithm. The results demonstrate the suitability of the proposed algorithms in identifying the rock types based on their strength properties, which can be adopted in measurement while drilling systems.

Jan 1, 2014

By Naj Aziz, Peter Craig

"Double shearing tests were carried out on the 28 mm (1 in) hollow strand Jennmar TG cable bolt to gain a better understanding of the shearing behavior of the cable. The first test was limited to a 50 mm (2 in) travel on the testing machine and produced a shear load of 900 kN (92 t) at the maximum 50 mm (2 in) displacement. The axial load generated on the cable bolt was 238 kN (24.3 t). In the second test, the machine travel was increased to 75 mm (3 in), and first strand failure of the cable, due to shear loading, occurred at 1,354 kN (138 t) vertical load at a vertical displacement of 59 mm (2.3 in). The cable axial load was in the order of 385 kN (39.3 t). Analysis of the failure mode and loads achieved showed that the cable strands bent and the concrete crushed along the shear plane; the shear loading across the concrete and grouted cable then reached the tensile strength of the steel wires.INTRODUCTIONCable bolts were introduced to the mining industry around 1970, initially to surface mining and underground metalliferous mining and then to coal mining in the early 1980s, mainly for roadway reinforcement as a secondary means of support. Cable bolts have since been used as both primary and secondary supports. As primary support, Fuller et al. (1994) described the application of cable bolts, known as FLEXIBOLT, for strata reinforcement in both Angus Place and Ellalong Collieries, in New South Wales (NSW), Australia. As secondary support, cable bolts have also been used as cable trusses, which act to support the immediate roof in a sling-like manner (Fabjanczyk and Tarrant, 1988; Fuller, et al., 1991; O'Grady and Fuller, 1992), and for reinforcement at higher stratification and beyond the rebar bolt length, mainly for anchoring lower strata layers immediately above the coal seam to the higher, competent bedding formation above. Initially cable bolt anchorage was by cementatious grouting and, since the 1990s, by chemical resin. The dominant type of cable bolts used for secondary support in Australian underground coal mines are 588 kN (60 t) capacity cables which are point anchored, pre-tensioned and post-grouted. Point anchored refers to a cable resin anchor. The cables are tensioned on the resin anchor; then the same cable is grouted by cementatious grout pumped to ·fin the annular gap around the cable from the collar of the hole to the resin anchor. Bulbs are located within the resin anchor section for mixing of the resin chemical components and efficient anchorage. The installation of these typically 8 m long cable bolts involves a lot of manual handling of the cables, lifting of heavy hydraulic tensioners, and exposure to resin grouts. Table 1 shows the specification of various cable bolts currently marketed and installed in Australian underground coal mines."

Jan 1, 2010

By Kudret Tutuk, Serkan Saydam, Sungsoon Mo

"This paper presents an overview of the floor heave management at the Glencore Bulga Underground Operations and investigates the contributing factors to the behaviour of the floor. The mine experienced a number of major floor heave events in gateroads on development. As the longwall face approached the roadways, the magnitude of floor heave frequently increased, while new floor heave also developed. Furthermore, severe floor heave events took place along the longwall face. The most observed failure mode was buckling. While regular floor measurements were conducted to better understand the nature of the phenomenon, and various measures were considered to control the deformation of floor, the mining height was increased for the predicted floor heave domains, which facilitated effective management of the floor issues. The experience in the mine indicates that mainly high horizontal stresses with greater depths of cover and certain types of floor lithology configuration are likely to contribute to the failures of floor strata.INTRODUCTIONThe Glencore Bulga Underground is located in the Southwest of Singleton in the Hunter Valley of New South Wales, Australia. Blakefield South, part of Bulga Underground, commenced longwall mining in 2010, extracting coal from the Blakefield seam, while the overlying longwall panels were previously mined from the Whybrow seam. The coal seam ranges from 4.5 m to 8.0 m thick with the mining heights varying from 2.9 m to 3.5 m. The longwall panels are 320 m and 400 m wide and up to 3.5 km long.The mine experienced a wide range of floor issues around longwall panels LW7 and LW8, both 400 m wide. For instance, the concrete floor in the travel road failed and lifted as the longwall retreated in close proximity as can be seen in Figure 1. Figure 2 shows the beam stage loader (BSL) buried into the lifted floor, and Figure 3 shows a timber prop distorted due to the movement of the floor. In addition, severe deformation of the floor along the longwall face impeded the longwall operation, as shown in Figure 4."

Jan 1, 2018

By Houquan Zhang, Yu Wu, Yanlong Chen, Zhenfu Luo, Aihong Lu

"A non-destructive detection scheme for bolt installation quality was designed by adopting the method of non-destructive detection on bolt installation quality. Based on the field measurements, a random non-destructive detection method for determining the characteristic length including anchoring length, free segment length and initial axial load of bolt was discussed, and the characteristics of increasing bolt axial load in the initial stable stage was obtained. The results show that the bolt axial load and deformation of surrounding rocks correlate each other. Compared with the traditional detection technique for bolt installation quality, the non-destructive detection method has obvious advantages such as random, accuracy, and economic. The method provides a reliable basis for bolt support optimization and stability control of surrounding rocks.INTRODUCTIONBolt support in roadway can make the surrounding rocks and bolt form a structure in the early stage of roadway development through the bolt pre-tension, which can maximize the self-bearing capacity of surrounding rocks. Thus it is a form of active support (Kang, 2007). In order to make the bolt play an active supporting role, it needs to ensure the installation quality of bolting. Thus the bolts can supply a high initial anchoring force and control the deformation of surrounding rocks (Shan, 2009; Wei, 2012). Moreover, bolt supporting is a concealed work. Once installation quality problems appear; it will be difficult for effective detection and screening (Xie, 2008).THE PROBLEMS OF BOLT INSTALLATION QUALITY IN COAL MINE AND ITS DETECTIONThe Problems of the In Situ Bolt InstallationDue to the problems in installation environment, machine, and technique, and workers proficiency (Li, 2003), there are many problems exist in bolt installation. If the borehole depth is too long, the anchoring agent will accumulate at the bottom of the bore, which reduces the anchoring length. Furthermore, if the borehole depth is short due to the poor geological condition, the exposed part of the bolt will be too Jong and the pallet cannot cling to the rock face, which prevent the pre-tension from being applied. The pre-tension is very important for bolt installation. If pre-tension is insufficient the rock bolt cannot control the deformation of surrounding rock efficiently and the bolt anchoring force will decrease considerably. The bolt length is another important parameter for anchoring quality, which will affect the control area of bolt supporting. In addition, the cleanness of drill hole has a great influence on the effective anchorage length of bolt. If the drill hole cleaning is not enough, it will directly affect the anchoring agent and the contact area of surrounding rocks, which will decrease the effective anchorage length and initial anchor-force."

Jan 1, 2016

By Ben Mirabile, Alan Campoli, Rodney Poland

"The majority of U.S. underground coal mines use some form of cable bolt as supplemental support to a primary roof bolting system. Many coal operators employ the high load capacity of non-tensioned cable bolts, cable roof trusses, or solid bar trusses in an attempt to suspend the primary bolted horizon to overlying strata. However, in cases where many discontinuities exist in the roof strata or where pre-existing fractures are present, these passive supplemental support systems often cannot adequately control roof deflection. This paper examines the application of tensioned cable systems to minimize roof deflection in very laminated and fractured strata. Three underground case studies are presented to demonstrate the application of tensioned cable bolts. The first case study involves the rehabilitation of a longwall head gate in the Eagle Seam with highly laminated and fractured sandstone. The second case study examines the recovery of a longwall face in the Alma Seam. The final case study addresses rehabilitation of a longwall head gate in the Pittsburgh No. 8 Seam that was developed in a sandstone channel margin area and subjected to horizontal stress concentration.INTRODUCTIONDuring the previous decade, Jennmar Corporation has recognized coal operators' increasing interest in tensioned cable bolts. The majority of these tensioned cable bolt systems have been applied in adverse roof conditions including broken ground, high horizontal stress areas, and highly laminated roof strata. In most cases, qualitative data on roof conditions after application of tensioned cable bolt support indicate successful implementation of these systems. The qualitative evidence suggests that the combination of high load' capacity and applied tension provides superior supplemental roof support in adverse roof conditions. This research aims to quantify the effects of applied tension to cable bolts. This paper will review the types and installation of tensioned cable bolt systems, present initial laboratory test data, discuss successful case studies, and propose an instrumentation system for quantification of tensioned cable bolt performance."

Jan 1, 2010

By Donovan J. Benton

Photogrammetric methods are advancing rapidly and show considerable promise as a ground control research tool. The ability to quickly capture three-dimensional geometry, especially changes in geometry, in underground and laboratory settings is a significant advance from point distance measurements. Photogrammetry is being applied in both of these settings as part of the NIOSH ground control research. This paper describes these applications and the equipment and software being employed. It also describes tests conducted to quantify the accuracy of these systems. Accuracy varied with system specifics and procedures. A factory-calibrated camera produced results within 1/32 of an inch, plus 0.04%. A user-calibrated camera was found to be less accurate, at 1/20 of an inch, plus 0.24%. These calibrations demonstrate that photo grammetry can produce research quality measurements in laboratory and mine settings.

Jan 1, 2014

By Dongsheng Zhang, Xufeng Wang, Wei Zhang, Gangwei Fan

"Large-scale longwall mining of shallow coal seams could cause mining-induced fractures to communicate with the surface immediately in Northwest China, leading to a series of mine safety and environmental issues, including crack formation, water loss, vegetation deterioration, land desertification, and spontaneous coal combustion. Therefore, an accurate and effective understanding of the spatiotemporal evolution law of mining-induced fractures in overlying strata and its relationship to upper aquifers is critical. In this paper, the application of the geophysical-chemical properties of radon in mining engineering is explored as a potential solution to the shortcomings of existing surveying methods. A radioactive measurement method is proposed for the detection of the development of mining-induced fractures in overlying strata in the Baoshan Coal Mine (BCM). The on-site trial indicated that the first weighting step is approximately 60 m, the average periodic weighting step is approximately 20 m, and the influence coverage of the advanced abutment pressure is approximately 30 m. The presented method could be used as an indirect technical support to increase the safety of coal mining by acting as a simple, fast, and reliable method of detecting mining-induced fractures in overlying strata.INTRODUCTIONAccording to the latest coalfield prediction results provided by China’s National Administration of Coal Geology (CNACG) (Zhou et al., 2013), China’s coal resources are mainly distributed throughout the West, e.g., Inner Mongolia, Xinjiang, Shaanxi, Shanxi, Ningxia, and Guizhou. Two major coal mining areas have been established in the Northwest and the Southwest, and are typically represented by Inner Mongolia and Guizhou (Zhang et al., 2010). Northwest China is an arid to semi-arid area, where the coal seams are typically shallow and covered by a thin layer of bedrock. In its natural state, the surface’s ecological environment is fragile. Large-scale longwall mining of shallow coal seams could cause mining-induced fractures to communicate with the surface immediately, leading to a series of mine safety and environmental issues, including crack formation, water loss, vegetation deterioration, land desertification, and spontaneous coal combustion. This can propel any potential ecological fragility into a state of actual destruction (Zhang et al., 2011). Therefore, an accurate and effective understanding of the spatiotemporal evolution law of mininginduced fractures in overlying strata has become the theoretical basis of solving the above issues."

Jan 1, 2015

By Wei Yin, Yu Wu, Xiexing Miao

"For engineering problems of “three under” coal (coal trapped under buildings, waters-bodies and railways) exploitation, environment protection and gangue separation from raw coal underground exist in Tangshan Coal Colliery. By analyzing concrete technical problems, a technical approach of closed cycle “coal mining-gangue washing-backfilling-coal mining”, i.e. integration of coal mining, gangue separation and solid backfilling, is put forward with key technologies including gangue transportation with great depth, gangue separation from raw coal underground and integration of coal mining and backfilling. Based on the specific geological conditions of Tangshan Coal Colliery, 591m vertical feeding transportation system with great depth is designed; meanwhile, for efficient gangue transportation, ancillary wear-resisting pipe size and buffer equipment are optimized. Underground gangue separation system is created to be joined with the existing production system and backfilling system; besides, as per separation characteristics of coal and gangue, buddle jig is adopted for gangue roughing of raw coal underground. By cooperation of backfilling hydraulic support and other key equipment, the designed stope backfilling system completely realizes integration of coal mining and backfilling. Engineering practice shows that, through the research and implementation of the above key technologies, integration of coal exploitation, gangue separation and solid backfilling is successfully implemented in Tangshan Coal Colliery; moreover, it completely solves the three major engineering problems and realizes waste disposal, underground washing and separation, and ground surface subsidence control.INTRODUCTIONSo far, “three under” coal (coal trapped under buildings, watersbodies and railways) and key state-owned coal resources trapped under villages in China have reached 13.7 billion t and 5.22 billion t, respectively. With the development of coal enterprises, China currently has more than 1,600 gangue dumps (Miao et al., 2010a) with accumulated stack amount of 4.5 billion t, occupying a land area of 150,000 km2; moreover, surface subsidence caused by mining activities has damaged the environments of industry, agriculture, transportation and living, while new environmental pollution sources formed by coal related industries also result in damage to ecological environment (Huang et al., 2011a). On the one hand, due to large scale coal mining, some coal collieries suffering from resource exhaustion are faced with survival problems; on the other hand, coal mining has caused and been faced with increasingly prominent environmental problems, such as “three under” coal exploitation, waste disposal and ground surface subsidence control (Miao et al., 2010b; Zhang et al., 2009)."

Jan 1, 2015