Search Documents

By Andre Cezar Zingano

"The objective of this paper is to estimate the coal seam strength and the pillar safety factor for low coal seams using back analysis and rock mass characterization. The coal seam strength is very important to estimate both pillar capacity and mine section design. There are two approaches to estimating coal seam strength: (i) by geomechanics characterization of the boreholes cores; and (ii) by back analysis from pillars successes and failures, or some in-situ tests. For low coal seams (1.2 m, or 47 in.), the confinement of the center of the pillar is very important to defining global pillar strength because the low seam height increases the confinement of the pillar core, even in small pillars. We used in this case study one underground coal mine in the Parana State where the coal seam thickness is 0.8m the pillar height is 1.3m, the entry width is 5m and seam depth is 130m. A panel test was prepared to study the pillar behavior for use of the retreat mining method. The designed pillar size was 6x5m and 1.3m high with a predicted safety factor of 1.0 based on the Hoek and Brown failure criterion is 5.3 MPa. Once no pillar failure was observed, the pillar safety factor was assumed at 1.0 and the coal seam strength was backcalculated. The back analysis estimated the coal seam strength to be 6.2MPa. The confinement of the pillar center directly affects the coal pillar strength, and also the coal seam strength estimated by back calculation.IntroductionThe coal seam strength is very important to estimating pillar strength and mine section design. There are two approaches to estimating coal seam strength: (i) by geomechanics characterization of the coal seam using borehole cores; and (ii) by back analysis from pillar successes and failures, or some in-situ tests like panel test or ultimate pillar capacity (Salamon and Munro, 1967; Maleki, 1981; Peng and Dutta, 1992). For the first approach, lab tests (mainly triaxial tests) and borehole geomechanics descriptions (quality and quantity of the discontinuities) determine the coal seam strength by the Hoek and Brown failure criterion (Hoek and Brown, 1997). For the second approach, a panel test to study the pillar behavior can be built to define coal seam strength by back calculation. The safety factor for the pillars in the test is 1.0, based on the estimated coal strength from the geomechanics characterization. In this case, the probability of failure is 50%. If some pillar failure occurred, and the real pillar size was measured, the back analysis could be applied to define pillar strength and the coal seam strength."

Jan 1, 2015

By Robert B. Francini

Longwall mining and pipelines have coexisted since longwall mining was introduced into the United States. How the pipeline operator reacts to longwall mining under their line depends on many factors. This paper outlines the process the pipeline operator goes through to determine the appropriate response when their pipeline is being undermined. Typical mitigation procedures are reviewed. Finally, the paper looks at current design practices for new pipelines that are expected to be undermined during their lifetime.

Jan 1, 2011

By Erik Westman, Benjamin Mirabile

"Quantitative evaluation of secondary support performance in longwall tailgates in U.S. coal mines was introduced with the U.S. Bureau of Mines (USBM) Wood Crib Performance Model. This model evaluated crib performance based on load capacity, stability, and convergence characteristics. The introduction of a large variety of alternative secondary supports in the 1990s prompted a full-scale load-displacement testing program conducted by the USBM and, subsequently, NIOSH. The application of the ground response curve concept to secondary supports provided a more complete estimation of secondary support loading in longwall abutment zones. Secondary support loading from floor heave, horizontal stress effects, and pillar yield are captured by the ground response curve. A point on the ground response curve can be measured by instrumenting a secondary support with load and convergence measurement devices. A segment of the ground response curve can be measured by instrumenting two secondary support types of varying stiffness. Numerical models have been used to construct complete ground response curves for longwall tailgates based on measured secondary support performance. The ground response curve concept can be used as a design methodology for secondary supports in the #2 entry, as well as the longwall tailgate. Extending published evaluation and design methodologies for secondary support in longwall tailgates, a ground response curve unique to the loading conditions and required functionality of the #2 entry can be developed. Numerical models can be used to construct full ground response curves based on measured data in the #2 entry.INTRODUCTIONA longwall ventilation system is designed to continuously dilute and move methane-air mixtures and other contaminants from the active face, to bleeder systems, and out of the mine. The #2 entry of the tailgate gateroad serves to transport contaminated air from the longwall face to the bleeder system. The #2 entry is required to function as an air course between two longwall gobs and is subject to significant ground movement and loading. Current ground support design and evaluation practices are based on empirical evidence and little to no quantitative data on support performance exists for these entries. Substantial volumes of research have been conducted on ground movement and support performance in longwall tailgate entries. Following the successful ground support evaluation and design practices established for longwall tailgate entries, a practical and efficient design methodology can be adapted for supporting the #2 entry of a three-entry gateroad system."

Jan 1, 2018

By Jesse Puller, Ken W. Mills, Owen Salisbury

"An underground coal mine located in New South Wales has a target coal seam located 160-180 m deep directly below a 16-20 m thick conglomerate unit that has been associated with significant periodic weighting events on the longwall face. As part of the investigations to better understand the causes of periodic weighting at the mine, inclinometers capable of measuring horizontal shear movements through the full section of the overburden strata were installed ahead of mining at two locations approximately 1 km apart above the centre of two longwall panels. These inclinometers were monitored as the longwall approached each site. This paper presents the details of the installation, the results of the inclinometer monitoring at both sites, and the insights that these measurements provide for overburden behaviour about longwall panels.Horizontal shear movements were observed to develop on shear horizons that correlate closely across the two sites suggesting a mechanism that is consistent across a large area of the mine. Shear movements were observed to develop on a single horizon near the top of the conglomerate strata that was mobilised almost immediately after initial formation of the longwall goaf at a distance of 425 m ahead of the longwall face. The direction of horizontal movement was consistent with the relief of the major principal horizontal stress. As the longwall face approached each inclinometer, other horizons within the upper part of the overburden strata begin to shear with the upper strata moving toward the approaching goaf more than the lower strata. Within the last 30 m of longwall approach, tilting of the strata associated with the increase in vertical subsidence toward the extracted goaf caused a change in the style of deformation with tilting and reverse shear offsets.INTRODUCTIONLongwall mining is recognised from subsidence monitoring, surface extensometer measurements, and various other observations to cause significant disturbance to the overburden strata directly above the extracted goaf of each longwall panel. Disturbance to the overburden strata beyond the limits of each longwall panel is not so well understood. Subsidence monitoring indicates that horizontal movements beyond the edges of the extracted longwall panel are generally greater in magnitude than vertical subsidence and horizontal movements may extend up to several kilometres from the edge of the panel in some circumstances (Reid 1998, Reid 2001, Hebblewhite et al 2000, Mills 2001, Mills 2014). The mechanics of how these movements are accommodated within the overburden strata is only poorly understood and there are few direct measurements."

Jan 1, 2015

By Brian E. Perrine

Underground mining requires a variety of specialized equipment. With ever-changing mining conditions and methods, some mines have had to resort to purchasing existing industrial equipment and adapting it for underground use. Since this equipment is not made for underground mining or their specific task, the result is often lost time, money, and sometimes an unsafe working condition. One such application is the setting of a CAN. A CAN is a type of cylindrical secondary roof support made from a cement composite and encased in steel. The CAN has become popular because of its simple one-piece design that can handle heaving and sagging better than other available designs. ?Because of this exceptional ability to sustain load through extended convergence and displacement, the CAN is one of the most robust and stable standing supports in use today.?It also promotes better air flow due to the size and shape of the CAN. CAN size and weight have increased over time to handle more difficult mining conditions. Significant down time and inefficiencies with existing CAN setting machines at Twentymile Coal were directly due to the item in use not being designed to be task-specific. They were undersized with very limited movement. The miners had to take extra steps and precautions when setting CANs. Maintenance delays were significant. Twentymile Coal Company realized that they required a safer, more reliable and more efficient machine to handle and set CANs, and looked for a partner to develop a new design-specific machine. They worked jointly with J.H. Fletcher® engineering and sales to design and manufacture a machine specifically made for setting CANs. The objective was to produce a machine that would handle the conditions and methods that the mine required for setting CANs during longwall retreat. The resulting design had to be safe, stable, have a wide range of motion, be ergonomic, simple to use, and easy to maintain. The machine also had to improve efficiency. The resulting machine has been operating for approximately one year at Twentymile Coal and has been proven to improve safety, reliability, and efficiency. In conclusion, with the task-specific CAN Manipulator, the mine is able to better plan daily tasks with the knowledge that the machine will be available throughout a shift, and the employees will be safer because of the machine?s ergonomics, stability and safety. This has resulted in better productivity and a safer environment.

Jan 1, 2013

By John Cassie

The condition of roadways in the Deep Main seam at Asfordby mine, operated by RJB Mining (UK) Ltd, is strongly dependant on drivage direction relative to the maximum horizontal stress. The mine is laid out with gate roads driven approximately parallel to the maximum horizontal stress giving favourable drivage conditions. This has led to particulary difficult conditions for face installation headings which have to be driven to an increased width and at a high angle to the horizontal stress. A solution to the formation of face headings is described making use of stress relief with the face heading being driven in the zone of reduced stress surrounding a previous heading. In implementing this solution use was made of results from computer modelling and detailed monitoring of roadway behaviour. High reinforcement densities including cable bolts were used in supporting the headings. The experience provides an example of a traditional technique being applied more scientifically. The results obtained demonstrate the effect of stress relief and reinforcement methods in altering drivage conditions and suggest possible alternative strategies for the formation of future face headings in these conditions.

Jan 1, 1997

By Weidong Pan, Yinchao Yang, Baodong Zuo

Fully mechanized mining technology, with a large cutting height in thick coal seam, has been developed to be large-scale, mechanized, and intelligent. Furthermore, it is also superior to other mining methods because it operates more efficiently and has higher recovery rates of coal resources. Dongpang coal mine (located in north China) is one of the largest coal mining productions in Hebei province. It is significant because it is the first set of coal mines in China to adopt fully mechanized mining technology that has large cutting height potential. When looking at the coal seams of deep mining, specifically in the mine No. 2612 where the working face is 4.5–6.5 m cutting height, the coal walls have low stability due to the way the coal seam fluctuates in a large working face. This paper adopts mechanical analysis, numerical simulation, and field observation research methods to control the rib fall of coal walls in a coal mine. By adopting research methods that analyze the mechanical characteristics of face roof, we are able to conclude the main roof structure of the masonry seam stability criterion in overhead mining with large cutting height. This is done through employing the numerical simulation method, which helped to determine the main factors that influence the rib fall of a coal wall and weighting factor. Through field observations, we discovered the technology method to relieve, control, and mitigate rib falls of coal seam in a coal mine. We also discovered methods that would ensure the smooth mining of the working face of the mine by strengthening the bolting and grouting reinforcement methods used to improve the working face of stope surrounding rock conditions. This paper discusses research results that enrich the stope wall rock control method by expressing how fully mechanized mining technology, with a large cutting height, is meaningful to solve the complex conditions of rock fall caused by thick coal seam.

Jan 1, 2017

By Timothy Batchler

"Standing roof supports help to provide a stable working environment in coal mine gateroads. NIOSH participates in the development of these support systems by conducting full-scale tests in their Mine Roof Simulator. These tests have established the performance characteristics of every coal mine support system currently in use in the United States. Through these tests, mine operators and regulatory officials have acquired a fundamental understanding of the various types of support performance that guides the assessment and use of these support systems. However, some little known factors that influence support behavior can lead to misconceptions and, perhaps, a poor assessment of support behavior at times. This paper highlights several of these factors and discusses their significance. The paper also examines a current longwall tailgate support and discusses the inefficiency with this approach. Finally, the NIOSH Mine Roof Simulator (MRS) is the world’s most powerful load frame built specifically to test full-scale roof supports, including longwall shields. are addressed in this paper to provide a more in-depth assessment of the limitations of the MRS and what the MRS testing protocol is designed to do. INTRODUCTION Over the years, considerable research has been conducted to develop standing support technologies and to evaluate their performance characteristics. The load and displacement characteristics of the standing supports have been determined from full-scale testing conducted using the National Institute for Occupational Safety and Health (NIOSH) Mine Roof Simulator (MRS) (Barczak and Tadolini, 2008) located in Bruceton, PA. Performance traits, installation patterns, and ground responses are observed in various geological and mining conditions and are evaluated to determine the support performance in the field (Dolinar, 2010; Campoli, 2015; Zhang et al., 2012). Despite widespread use of standing supports, not every aspect of their performance and resulting ground support capability are always well understood. This paper discusses 10 factors, several of which are surprising, that impact standing support performance."

Jan 1, 2017

By Peter Fischer, Heinz-Jiirgen Kateloe, Anton Sroka, Axel Preusse

"Since mining in Germany has a long history, there are still many locations where the surface fracture problem has to be solved. Shallow mine workings from an earlier era can affect the surface in a discontinuous way. In many cases, due to light overburden load, those mine rooms did not collapse and a downfall can suddenly happen for many reasons, e.g., in connection with a changed load entry into the subsurface or by additional influence of water. This results in ground movements, which in extreme cases, appear as surface fractures.Depending on the use of the surface, ground movements caused in such a way constitute an endangerment by law. Particularly, within the southern Ruhr district, surface fracture and subsidence endangered ranges are determined on the basis of an empirical method that resulted from a systematic evaluation of surface fractures and rock disclosures. This method indicates maximum ranges within which impacts from abandoned shallow mine workings must be assumed.With a special emphasis on a risk management approach, RWTH Aachen University adapted the model of stochastic media to the conditions of abandoned shallow mining to compute and illustrate potential ground movements due to the collapse of shallow mine workings. Further investigations were concerned with the analysis of characteristic parameters which can serve for the assessment of the surface fracture probability in a comparative view of different cases. In recent years, more than 50 surface fractures in the southern Ruhr district were analyzed in order to develop a risk assessment of surface fracture endangered ranges over shallow mine workings. The results that have been obtained so far are described in this paper.INTRODUCTIONAbandoned underground mine workings of shallow depth can pose a threat to the surface. Due to small overburden rock loads, shallow excavations often remain intact for decades after the operations have ceased and may collapse abruptly (Braemer et al., 2005; Hollmann and Nuerenberg, 1972; Preusse et al., 2007). Several approaches for prognosis of surface fracture resulting from 97 subsurface collapse deal with this topic (Loebel and Sroka, 2001; Tajdus and Sroka, 2009)."

Jan 1, 2010

By Juan J. Monsalve, Nino Ripepi, Richard Bishop, Jon Baggett

"Terrestrial laser scanning (TLS) is a useful technology for rock mass characterization. A laser scanner produces a massive point cloud of a scanned area, such as an exposed rock surface in an underground tunnel, with millimeter precision. The density of the point cloud depends on several parameters from both the TLS operational conditions and the specifications of the project, such as the resolution and the quality of the laser scan, the section of the tunnel, the distance between scanning stations, and the purpose of the scans. One purpose of the scan can be to characterize the rock mass and statistically analyze the discontinuities that compose it for further discontinuous modeling. In these instances, additional data processing and a detailed analysis should be performed on the point cloud to extract the parameters to define a discrete fracture network (DFN) for each discontinuity set. I-Site Studio is a point cloud processing software that allows users to edit and process laser scans. This software contains a set of geotechnical analysis tools that assist engineers during the structural mapping process, allowing for greater and more representative data regarding the structural information of the rock mass, which may be used for generating DFNs. This paper presents the procedures used during a laser scan for characterizing discontinuities in an underground limestone mine and the results of the scan as applied to the generation of DFNs for further discontinuous modeling.INTRODUCTIONAccording to the Mine Health and Safety Administration (MSHA), between 2006 and 2016, the underground stone mining industry had the highest fatality rate in 4 out of 10 years, compared to any other kind of mining (MSHA, 2016). Additionally, during that same time, 40% of the fatalities were due to ground control issues, such as roof and rib collapses and pillar bursts. The National Institute for Occupational Safety and Health (NIOSH) developed guidelines for designing underground stone mines (Esterhuizen, Dolinar, Ellenberger, and Prosser, 2011). However, these guidelines do not apply to all underground stone mines.Monsalve, Baggett, Bishop, and Ripepi (2018) present a case study of an underground limestone mine experiencing a structurally controlled mode of failure. The authors analyze different methods to study that type of instability. They conclude that the integration of terrestrial laser scanning (TLS) with discrete element modelling (DEM) can be used to prevent rock falls in underground excavations to enhance worker safety. However, an adequate rock mass characterization and structural mapping must be performed in order to generate reliable models that allow the engineer to have a better understanding of the rock mass behavior."

Jan 1, 2018

By Peter Zhang, Daniel Su, Essie Esterhuizen, Mark Van Dyke, Berk Tulu, Dave Gearhart

"Roof falls in longwall headgate can occur when weak roof and high horizontal stress are present. To prevent roof falls in the headgate under high horizontal stress, it is important to understand the ground response to high horizontal stress in the longwall headgate and the requirements for supplemental roof support. In this study, a longwall headgate under high horizontal stress was instrumented to monitor stress change in the pillars, deformations in the roof, and load in the cable bolts. The conditions in the headgate were monitored for about six months as the longwall face passed by the instrumented site. The roof behavior in the headgate near the face was carefully observed during longwall retreat. Numerical modeling was performed to correlate the modeling results with underground observation and instrumentation data and to quantify the effect of high horizontal stress on roof stability in the longwall headgate. This paper discusses roof support requirements in the longwall headgate under high horizontal stress in regard to the pattern of supplemental cable bolts and the critical locations where additional supplemental support is necessary.INTRODUCTIONLongwall mining is the primary underground coal mining method in the United States and currently accounts for more than 60% of the underground coal production. The longwall headgate, as a passageway for the longwall crew, intake air, material supplies, and coal belt transportation, is critical for both safety and continuous production of the longwall panel. A roof fall in the longwall headgate would not only result in substantial interruption of production but could potentially cause injuries or fatalities. Rehabilitation of failed roof in the headgate would also expose miners to the risk of injuries. Roof falls in the headgate, though infrequent, mostly occur in the belt entry near the face. Considerable research has been conducted to determine the effects of various factors on headgate roof stability, as well as effective measures to support the roof in longwall mines in the Pittsburgh seam (Mark, Mucho, and Dolinar, 1998; Chen et al., 1998; Su and Hasenfus, 1995; Su, Thomas, and Hasenfus, 1999; Su, Morris, and McCaffrey, 2002; Su, Draskovich, and Thomas, 2003; Hasenfus and Su, 2006; Van Dyke et al., 2015). Previous studies have demonstrated that high horizontal stress and transitional roof geology are primary factors that cause headgate roof failure. These studies also showed that panel orientation, retreat direction, pillar sizes, and roof support played an important role in the stability of a headgate.In underground coal mines located in the eastern United States, the magnitude of the maximum horizontal stress is typically three times greater than the vertical stress, and about 40% greater than the minimum horizontal stress. Mark, Mucho, and Dolinar (1998) studied seven cases of headgate failures caused by high horizontal stress in different coal seams in the United States and stated that roof stability is affected, to a large extent, by rock type, entry orientation, and longwall orientation. The effects of horizontal stress can be summarized in these statements: (1) A laminated roof is very vulnerable to high horizontal stress. (2) Entries that are aligned with the maximum horizontal stress will suffer less damage on development than those perpendicular to it. (3) Horizontal stress concentration and relief depends on panel orientation, the direction of retreat, and the sequence of longwall panel extraction."

Jan 1, 2018

By Rob G. Jeffrey, Ken W. Mills, Jesse W. Puller

"A coal mine in New South Wales is longwall mining 300m wide panels at a depth of 160-180m directly below a 16-20 m thick conglomerate strata. As part of a strategy to use hydraulic fracturing to manage potential windblast and periodic caving hazards associated with this conglomerate strata, the in situ stresses in the conglomerate were measured using ANZI strain cells and the overcoring method of stress relief. Changes in stress associated with abutment loading and placement of hydraulic fractures were also measured using ANZI strain cells installed from the surface and from underground. This paper presents the results of in situ stress measurements and stress change monitoring undertaken as part of the hydraulic fracturing program.Overcore stress measurements have indicated the vertical stress is the lowest principal stress so that hydraulic fractures placed ahead of mining form horizontally and so provide effective pre-conditioning to promote caving of the conglomerate strata. Monitoring of the full-scale hydraulic fractures has confirmed the hydraulic fractures grow horizontally.Stress changes monitored during hydraulic fracturing formed part of a broader program to investigate fracture geometry and growth rates to confirm the characteristics of the hydraulic fractures placed. This monitoring showed that vertical stress in the conglomerate strata was being increased by up to 1 MPa in close proximity to the hydraulic fracture and had the effect of tending to promote asymmetrical growth of subsequent fractures about the injection borehole.Monitoring of stress changes in the overburden strata during longwall retreat was undertaken at two different locations at the mine. The monitoring indicated stress changes were evident 150 m ahead of the longwall face and abutment loading reached a maximum increase of about 7.5 MPa. The stresses ahead of mining change gradually with distance to the approaching longwall and in a direction consistent with the horizontal in situ stresses. There was no evidence in the stress change monitoring results to indicate significant cyclical forward abutment loading ahead of the face consistent with the observations of face conditions underground adjacent to both measurement locations. The forward abutment load determined from the stress change monitoring is consistent with the weight of overburden strata overhanging the goaf indicated by subsidence monitoring."

Jan 1, 2015

Previously, a variety of risk rating systems were used on different mines. However, these were mostly site specific and geology based systems. The purpose of developing a uniform rating system, to be used on all Anglo Coal open cast mines, is to provide an unbiased, standard and quantifiable assessment of the risk from highwall and lowwall failures. This takes into account relative differences in the importance of hazards, as experienced on each mine as a result of different combinations of geotechnical factors and mining conditions. The system is based on critical geotechnical and other parameters that have been identified by mining personnel and rock engineers. The primary advantage of this risk rating system is that all open cast mines in Anglo Coal use an almost identical system, which enables the user to compare their risk to the risk at neighbouring mines and/or other open cast mines. The system can be adjusted to meet local, mine specific requirements. The implementation of this new system (a computer program that automatically calculates the risk) has been made as practical and easy to use as possible. Therefore, this tool can be used by personnel from other mining disciplines not directly related to rock engineering.

Jan 1, 2004

By Christopher Mark

Coal bursts are typically associated with highly stressed coal. Most bursts occur during retreat mining (longwall mining or pillar recovery) in highly stressed locations like the tailgate corner of the longwall panel. Others are associated with multiple seam interactions. However, a small but significant percentage of coal bursts have occurred during development or in outby locations unaffected by active mining. Most development bursts have been relatively small, but some have been highly destructive. No theory of coal bursts can be complete if it does not account for this type of event. This paper focusses on the development mining coal burst experience in the US, putting it into the context of the entire US coal burst database. The first documented development coal burst occurred almost exactly 100 years ago during slope drivage at the Sunnyside Mine in Utah. Sunnyside subsequently had a long history of bursts, mainly during retreat mining but also during development. Several Colorado mines have also experienced multiple development bursts. Some, but by no means all, of the development bursts in these western US coalfields have been associated with faults. In the Central Appalachian coalfields, most development bursts have occurred in multiple seam situations. In some of these cases, however, there was no retreat mining in either seam. The paper closes with some lessons from this history, with implications for preventing such events in the future.

Jan 1, 2017

By Bruce K. Hebblewhite

BHP Billiton Illawarra Coal operates Dendrobium Mine in an area 10-20km west-northwest of Wollongong in the Southern Coalfield of New South Wales, Australia. The mine recently completed longwall mining in Area 3A adjacent to an overhanging rock feature known as Sandy Creek Waterfall, which had been identified as a significant, and potentially sensitive natural surface feature of the environment. This waterfall lies within the Sydney drinking water catchment area, in a surface terrain of variable topography where non-conventional subsidence behaviour such as valley closure, and far-field horizontal movements are known to occur, over and above conventional subsidence responses to mining. As a part of the conditions of approval to mine, Illawarra Coal undertook to protect the waterfall and the section of Sandy Creek immediately upstream of the waterfall from the effects of longwall mining using an innovative management process and an array of very high resolution monitoring systems. This paper outlines the type of non-conventional subsidence effects that can occur; the range of different monitoring regimes adopted in response to such effects in order to develop an understanding of the valley closure phenomenon in proximity to the waterfall and provide suitable early warning data. The paper also describes the management processes that were adopted, incorporating the use of these monitoring regimes in order to successfully protect the waterfall from the valley closure effects of mining four adjacent longwall panels in close proximity to the waterfall while continuing to maximise recovery of the coal resource in the area. The management structure adopted involved a technical committee, a steering committee, and an external independent reviewer. The technical committee was responsible for design of the monitoring systems, interpretation of the results, and making timely recommendations to the company steering committee who were then able to make informed decisions on when to cease mining each adjacent panel. The steering committee comprised Illawarra Coal management and technical personnel. Although the steering committee took advice from the technical committee, all decisions relating to mining were made by the steering committee. An external reviewer was engaged by the steering committee at the end of each longwall panel to review the results, interpretation and management decisions. This management structure was effective in successfully protecting the very sensitive structure of Sandy Creek Waterfall from potential impacts of nearby mining in the midst of active ongoing natural erosion processes.

Jan 1, 2014

By Marvin B. Thompson

"The depositional model for major Illinois Basin coalbeds is well documented and defined on a regional scale. The model was a driving force during past exploration for lower sulfur and thicker coal deposits. The most attractive coal reserves were known to lie along the flanks of contemporaneous sandstone filled stream channels and were overlain by thick silty gray shale roof. At various distances away from the channels, the depositional model transitioned to black shale I limestone roof, sulfur content of the coal bed increased, and the coal bed often thinned. Understanding the character of roof rock types associated with this depositional model is essential to predicting ground control factors on both a regional scale, and on resolving roof control problems at the mine-site. Additionally, horizontal stress and overburden depth are significant factors that impact roof rock quality and ground control in Illinois Basin mines.Determining the character of several rock types, and defining the primary horizontal stress direction were crucial to a recent successful project at New Future Mine, located in southern Illinois. An inclined slope was constructed from the Illinois No. 5 Coalbed up to the Illinois No. 6 Coalbed through strata that ranged from extremely weak ""stackrock"" and a weak underclay unit, to a massive sandstone unit. Engineering geology, operations management, and Jennmar technical services personnel teamedup to select and install roof support for each strata transition. The project was completed with no injuries and no roof falls.INTRODUCTIONAbundant published information concerning coal deposition, geographic distribution, quantity, quality, and mining conditions exists for Illinois Basin coal reserves. The State of Illinois, through its State Geological Survey (ISGS), has provided decades of research, record keeping, and service to the coal industry. Other excellent sources of Illinois Basin coal information include the Indiana Geologiq1l Survey and the Kentucky Geological Survey. Past research by the U.S. Bureau of Mines (USBM) supplemented the work by the geological surveys, especially in the area of horizontal stress and mining hazards. The National Institute for Occupational Safety and Health (NIOSH) continues to produce publications focused on roof control issues common to many coal basins, including the Illinois Basin. Many of the illustrations in this paper originated in ISGS and USBM publications."

Jan 1, 2010

By Victor V. Nazimko

Long term stability of the pillars that have been remained after R&P extraction causes postponed subsidence. To prevent unforeseen subsidence and to diminish postponed subsidence 25-50% new method for its control has been developed by the author. It supposes to use drilling and blasting technology and other original approaches. New method has been fulfilled through the holes being drilled from the surface or from the active underground openings. Explosives had been charged into the holes and were blasted. This had increased bulking factor dramatically and prevented natural caving of the strata. Physical scale modeling corroborated efficiency of the new approach. The bulking factor has grown from 0.0623 to 0.1185 and surface subsidence has been diminished from 1.1 m to 0.2 m or 5.5 times.

Jan 1, 1996

By Heather E. Lawson

Recent field data providing measured pillar loading from a deep western mine revealed that an increased load transfer distance existed compared to expected values (Larson et al., 2012). Additionally, recent work by Tulu and Heasley (2012) has shown that the abutment angle in deep longwall mines can be significantly reduced as the depth of mining increases. The load transfer distance and abutment angle are both used as parameters to estimate pillar loading in longwall design. To investigate the potential implications of these observations on pillar loading in deep longwall mines, a parametric study using ALPS loading estimation procedures was performed. A supplemental study was conducted using LaModel to further investigate pillar loading at the tailgate. The study found that the abutment angle is particularly important for panels with supercritical geometries. As panels reach a subcritical geometry with increasing depth, the primary influence of the abutment angle is reduced and matched by other factors, including load transfer distance for tailgate loading. An extended load transfer distance was shown to potentially reduce loading on pillars adjacent to the longwall as the loading is spread over a larger area. The results of these studies indicate a need for further field verification and research toward regional geologic influences on pillar loading and how these may impact ground stability.

Jan 1, 2013

By Dave Bigby

Hatworth Colliery, operated by RJB Mining (UK) Ltd, is successfully mining the Deep Soft Seam at a depth of 1000m using single face retreat longwalling. The seam is characterised by a weak roof generally comprising 4 to 6m of well bedded carbonaceous mudstones overlain by weak siltstones. The paper describes the layout and support design strategies which have enabled the colliery to adopt sole support by rock reinforcement techniques for its longwall gateroads. To achieve this success the colliery layout has had to be radically modified to take account of the in-situ horizontal stress field. The layout is also closely controlled by environmental considerations, the seam being one of the gassiest in the UK Economic support by strata reinforcement has been achieved using a combination of rockbolting of the roof and sides installed at the face of the heading, and systematic double birdcage cable bolting installed on drivage and supplemented ahead of the retreating panel. The layout and support strategies have been developed through a combination of detailed underground measurement of support and stress parameters backed up by numerical modelling using FLAC. The FLAC modelling has paid particular attention to careful representation of bedding properties and validation through underground stress measurement.

Jan 1, 1996

By Nicole E. Evanek, Anthony T. Iannacchione

"Over the past 36 years, a great deal of information has been presented and discussed at the International Conference on Ground Control in Mining (ICGCM). The topic of surface subsidence engineering has resonated throughout each of the 36 conferences, producing 155 related papers. These papers have come from many countries. The major focus has been underground coal, especially longwall mining, but hard rock mining has also received attention. This impressive collection of reports presents a unique opportunity to reflect on the progress made towards understanding subsidence basin characteristics and developing methods to predict and mitigate its impact.In the initial meetings, the focus was on measuring subsidence and developing prediction methods. As understanding increased, predictive methods were developed and tested, especially in North America, China, Australia, Europe, and India. Efforts were made to understand how structures, aquifers, and surface waters were impacted by the formation of subsidence basins. As time progressed, the number of papers dropped slightly and became more focused on site-specific conditions. Most recently, advanced monitoring techniques have revealed new information, spurring a resurgence in research activity. Another recent focus has been on anomalous horizontal deformations occurring in sites with significant relief. Several reports from Australia and one from the US have brought this issue to light. In closing, all of these surface subsidence engineering papers have chronicled the maturing of this most important topic and, in the process, highlighted the importance of the ICGCM in the evolution of our current state of practice.INTRODUCTIONThe aim of this paper is to examine the role of ICGCM in 1) shaping our understanding of the mining induced subsidence phenomena, 2) developing tools to help predict its impact on the surface, and 3) evaluating controls to mitigate these impacts.This analysis involved the consideration of 155 papers available within the ICGCM conference proceedings and listed under the subsidence topic. Three of the papers where only available as abstracts and were not included in this analysis. Four other reports were focused on topics other than underground coal mining-induced subsidence issues and were also not included. It should also be noted that papers dealing with overburden behavior were not included in this analysis. As a result, 148 papers were reviewed and analyzed (Figure 1)."

Jan 1, 2018