Search Documents

By Michael Amick

Due to the importance of maintaining open airways on a longwall panel, mine management decided to install cribs made of foamed cement. Foamed cement had been used at other company operations on several projects. A recent test at a sister operation had proven the crib installation technique and established that foamed cement cribs could provide better support than wooden cribs. The area to be supported was in a remote location; the limited material needs of foamed cement cribs offered a substantial advantage. In mid February 1993, 75 foamed cement cribs were installed on the tailgate of the active longwall panel. The 75 cribs resisted both horizontal and vertical stresses while successfully supporting the entry.

Jan 1, 1993

By Axel Preusse

On the basis of the Law on Financing Hard Coal Mining dated 28 December 2007, the subsidized German hard coal mining industry will be shut down to the end of the year 2018 in a socially acceptable manner; in 2012 this decision will be reassessed. Even after the abandonment of all mining activities subsequent burdens are inevitable. In this paper, the possible long-term effects resulting from a mining industry history, which is spanning more than 200 years, and their possible consequences are pointed out, in particular in connection with the abandonment of mine water drainage measures which is economically meaningful in the long term. According to the decision situation as it presents itself today, this point in time will be far beyond 2018. In preparation for this, an action framework is to be developed in areas possibly affected.

Jan 1, 2008

By A. T. Iannacchione

Recent fatal injuries occurring during pillar retreat coal mining call for better identification of the hazards and recognition of risks. Ground control hazards associated with room-and-pillar retreat mining tend to intensify with depth, requiring extra precautions in the form of additional controls. In many locations these activities are further complicated by local complexities often associated with unique or novel circumstances, such as over-mining or under-mining. One technique recently studied by NIOSH, Major Hazard Risk Assessment (MHRA), may help mine operators to mitigate the risks associated with pillar recovery operations. The approach was trialed at two underground coal mines in southern West Virginia that are currently practicing pillar recovery. The first step in the MHRA process involved reviewing the segments or parts of the pillar extraction mining system and identifying associated hazards and threats to the operation. Some of the high risk hazards at these two sites included: ? Rock fall during pillar extraction covers equipment and injury ? occurs during recovery operations, Rock fall above the roof bolt horizon, potentially injuring ? workers and/or requiring recovery action,Rib fall under deep cover, potentially injuring workers, and; ? Strata instabilities associated with subsidence of the ? interburden due to simultaneously mining two seams in close vertical proximity to one another. The mines? risk assessment teams then considered each threat individually in order to systematically identify potential unwanted events. The top unwanted events were examined individually using structured risk analysis tools. The output from the process includes a list of priority existing controls for monitoring and auditing, and a second list of potential new controls. These controls consisted of: ? Examples of best practices, ? Enhanced communication, ? Implementing standard operating procedures (SOP), ? Protocols for emergency response actions, ? Effective layouts, ? Efficient monitoring, and; ? Successful audits. This paper documents the process as it unfolded at the two mines, and analyzes the strengths and weaknesses of the MHRA technique as it applies to pillar recovery operations. This work was part of a larger NIOSH research project. NIOSH was responsible for: 1) facilitating the risk assessment process known as Major Hazard Risk Assessment (MHRA), 2) documenting the risk assessment process, and 3) providing mine management with a written draft summary of the risk assessment process. The results of the risk assessment represent the thoughts and opinions of the individual risk assessment teams and should in no way be construed as an endorsement of the risk assessment output by NIOSH or the University of Pittsburgh.

Jan 1, 2009

Coal mass strength properties must be estimated to obtain realistic estimates of coal pillar strength. The limitations of existing techniques for approximating these properties are discussed. The coal mass is anisotropic. The Hoek and Brown approach to rock mass property estimation is modified to allow for this. This approach requires the Rock Mass Rating (RMR) for the strata. In the normal case where bedding is sub-horizontal, these major planes of weakness have little effect on the strength of pillars. As a result of this the RMR must be measured parallel to bedding. This means that a significantly higher rating than that usually obtained for coal is observed. The use of mass strength property estimates in extant empirical relationships is outlined. At high width to height ratios, an acceleration in the rate of increase in pillar strength with increasing width to height ratio has been observed. The empirical relationship developed by Salamon (the so called squat pillar formula) takes account of this. This relationship was found to have significant limitations with respect to its universal application. Modifications arc made to Bieniawski's empirical formula to extend its use to large width to height ratio (squat) pillars. This new squat pillar formula has none of the disadvantages associated with Salamon's relationship. Strain softening was incorporated into non-linear finite difference numerical modelling to estimate pillar strengths. The technique outlined above is used to obtain peak coal mass properties. Modelled pillar strength was found to be sensitive to both peak and post peak mass strength properties. Post peak properties were found to be difficult to obtain and required some back analysis. Modelling results were used to estimate both the strength of squat pillars and parameters for use in a now squat pillar empirical strength relationship.

Jan 1, 1992

By Kot F. Unrug

Strength of coal is one of the governing factors in size determination of mine pillars, and therefore affects the percentage of extraction and thus, utilization of reserves. Coal strength is also important from the subsidence control standpoint, where mine pillars with appropriate safety factors should be designed for long term stability. Determination of coal seam strength has been addressed through the extrapolation of the coal strength obtained from a small number of samples on the whole section of the seam. This procedure often gives unreliable results. Presented in this paper is a method of in-situ strength testing of coal, allowing for a realistic determination of seam strength. Results of a field case study dealing with the coal seam, where samples for the laboratory strength tests could not be obtained due to the dense cleat, are presented. However, in these conditions, the in-situ testing was successful. A comparison of both conventional and the in-situ penetrometer method was carried out. It was found that the penetrometer data not only improve the accuracy of strength determination of the entire seam, but also prove to be much more cost effective than the conventional method on a per test basis.

Jan 1, 1995

By Daniel Su

Following several roof falls in the E3 longwall development of a Consol Pennsylvania Coal Company underground coal mine, an underground roof geology reconnaissance program consisting of twenty-nine 20-foot deep roof holes had identified the presence of thick sandstone layers with abundant shale and micaceous streaks. The base of the sandstone was 4 to 8 feet above the roof line within the fall areas. The presence of micaceous streaks created extremely pronounced planes of weakness in the sandstone. A structural irregularity, which extends into the E4 and E5 developments, exists between crosscuts I 1 and 30,where all roof falls occurred. Immediately to the east of this structural irregularity lies a huge syncline. The presence of thick sandstone units within the typically all shale environment and within such a structural irregularity helps to maximize stress concentration and creates closely spaced joints in the sandstone, which explains why many cracks are present in the macroscopically massive sandstone upon development. The approaching E2 longwall gob to the south and on the down-dip side, on the other hand, provided horizontal stress relief in the sandstone, which helps to explain the many roof falls in the E3 development that occurred during or immediately after the formation of the E2 gob. Finite element modeling confirmed the presence of such horizontal stress relief. Since the E3 longwall was a right-handed face, stress concentration was expected at the longwall headgate T -junctions, and further delamination of the sandstone was expected upon arrival of the E3 longwall face. Based on the results of the roof geology reconnaissance program and a roof stability analysis that took into account up to eleven parameters, supplemental headgate and track roof support consisting of 16-foot and 20-foot long cable bolts was successfully implemented within the zone of thick sandstone with micaceous streaks and structural irregularity and at other potential roof instability areas along the E3 development. The cable bolts were designed to be anchored at least 4 feet above the sandstone unit into the mostly competent sandy shale layers. No headgate roof control problem was reported within the sandstone and structural irregularity zone during E3 and the subsequent E4 longwall extractions.

Jan 1, 2002

By J. S. Oram

Maltby Colliery, operated by RJB Mining (UK) Ltd is successfully mining the Parkgate seam in Yorkshire at a depth of 1000m using longwall retreat. Extraction in the Parkgate seam is influenced by interaction from previous workings in the Swallow Wood Seam 160m above. The paper describes in-situ stress measurements and simple gate road convergence measurements carried out to assess the extent of the interactive influence. The stress measurements, obtained using the stress relief overcore technique, were carried out from a maingate development roadway in an area where the stress redistribution under an overlying pillar and adjacent panel goat could be measured. The measured vertical stress distribution confirmed a significant interactive influence with high imposed vertical stresses under the overlying panel edges. Simple roadway convergence monitoring stations established in the gateroads of a retreating panel and in the development gateroads of the adjacent panel, confirmed higher rates of roadway deformation relating to overlying panel edges and pillars, particularly in the areas where a vertical stress window developed during panel retreat. In addition to highlighting a close relationship between closure rate and the measured vertical stresses, the convergence monitoring proved valuable in establishing characteristic deformation behaviour under specific interactive influences and also in defining the optimum location, extent and time of installation u£ additional roadway support and reinforcement. The information from the measurement programme has enabled the Mine Management to gain a better understanding of the interactive influences on roadway behaviour and was instrumental in designing the layout of panels in an area of the North East district of the mine where previous experience had indicated the combined influence of high interactive stresses and weak roof lithology resulted in difficult strata conditions both at development and on panel retreat. The planned location of panels and gateroads took into account both mining operational considerations and the need to avoid potentially high risk interaction zones as highlighted from analysis of the monitoring results. To obtain additional data on parameters influencing roadway deformation, extended roadway convergence monitoring has been established.

Jan 1, 1997

By Richard A. Allwes

A procedure is presented for the design of an arch canopy for the application of rehabilitating a high-roof-fall area. This procedure is specifically developed for evaluating an unbackfllled arch canopy, which Is subjected to an impact load (roof fall). Dynamic line loading of the arch canopy at its crown is only considered and the procedure does not account for an unsymmetrical loading condition. The evaluation of whether an arch canopy is suitable for a particular installation is dependent upon many variables, including in-nine conditions and the engineering properties of the structure. However, a general evaluation can be based upon a comparison of the arch's maximum crown deflection and a prescribed allowable crown deflection. A single spring-mass system is used as an idealized model to represent the dynamic behavior of the arch canopy at its crown. An energy approach is taken to determine the maximum crown deflection of an arch rather than solving a differential equation of notion derived from dynamic equilibrium. The design procedure is based on the concept that when an arch canopy is subjected to impact loading at its crown and deflects from its unloaded state to maximum crown deflection, the structure absorbs strain energy, both elastic and plastic. As a result, this strain energy can be calculated from a static load-displacement diagram for the structure. The significance of this design procedure Is that It gives mine personnel an analytical tool to select an arch canopy to meet the dimensional and functional requirements of a mine entry and a prescribed allowable crown deflection.

Jan 1, 1986

By Hamid Maleki

Roof falls are one of the leading ground control problems that adversely influence productivity and worker safety in underground mines, construction sites, and nuclear waste repositories. To control roof stability problems, the operator needs to have practical methods for measuring changes in strata conditions and criteria for defining the timing of secondary support installation. The objective of this study was to develop measurement techniques and criteria for assessing roof conditions at the mining face. An integrated rock deformation and tomographic imaging method was developed and applied at two sites in a western U.S. trona mine. It was shown that rock damage occurred at a deformation of 30 to 60 mm (1.2 to 2.4 in) (2 to 4 pct strain) and was associated with a significant (16 pct) reduction in wave velocity. Thus, supplementary support may be installed when there is a measured change in wave velocity of at least 16 pct. Tomographic measurements can be obtained in rocks rapidly, thus providing a powerful tool for analyzing growth of failure and for installing supplementary support systems in a timely manner.

Jan 1, 1996

By Vincent A. Scovazzo

Many accepted and useful methods have been developed and used for pillar design. Each method has its own particular strengths and weaknesses. Three methods addressed in this paper are; empirical, analytical, and numerical. Each of these methods have their place in pillar design. Analytical methods result in close approximation of the ideal pillar (most economical, stable, or yielding) and are suitable for use in final mine design and in analyzing existing problems. BOYD uses the analytical method to develop site specific mine pillars design equations. An analytical method, one of many developed by BOYD, is presented here and is based on the procedure used by Wilson (1) and others in development of their empirical equations.

Jan 1, 1995

By Renn Oler

Corrosion can often cause significant strength reduction and failure of steel rockbolts, thus demanding continuous rehabilitation and posing challenges to underground mines in maintaining long term ground support. The mining industry has traditionally applied galvanized and epoxy coatings for protection of ground support and reinforcement in corrosive environments due to cost considerations. However, under a harsh and corrosive groundwater condition with extreme pH levels, failure of the existing coated rockbolts often results in failure and falls of the mine roof, especially in long-term mine drifts or entries. To prevent the roof falls induced by corrosive bolt failure, DSI developed a new polymer coating, called ?Obduro AP coating,? to combat harsh and corrosive ground conditions. The new polymer coating was tested in extreme conditions to identify weaknesses and was found to be capable of handling highly corrosive mine water solutions. This paper highlights the challenges faced by underground mines with corrosive bolt failure and shows that the DSI Omega BoltTM can withstand the most corrosive ground conditions when it is coated in the new, economic Obduro AP coating.

Jan 1, 2014

By Jessica M. Wempen, William G. Pariseau, Michael K. McCarter

"Quantitative analysis of mine-wide subsidence at the kilometer scale and details of stress distribution about an advancing longwall face are estimated using an adaptation of the finite element method. The method is well suited to the tasks at hand. For greater realism, variability of strata properties is taken into account as are the effects of joints and cleats on elastic moduli and strengths. Evolution of pillar stress and entry closure remote from the face is readily quantified in a series of analyses that simulate face advance. Computed results compare favorably with the evolution of closure measurements about an instrumented pillar in a two-entry headgate. The appropriateness of the finite element method is confirmed. This method is based on first principles that avoid empirical schemes of uncertain applicability and numerical models “calibrated” by fitting computer output to mine measurements.INTRODUCTIONMine-induced seismicity is intimately related to strata mechanics associated with longwall coal mining and room and pillar mining, as well. Strata deformed beyond an elastic limit often tend to fail rapidly by brittle fracture and, thus, to emit acoustic signals in the form of elastic waves. Understanding the induced seismicity in coal mining offers the potential for early warning of hazardous conditions. Many years of experience with seismic phenomena associated with hardrock mining suggest considerable complexity should be expected. However, recent coal mine studies (Pariseau, 2014; Pariseau, 2015; Pariseau and McCarter, 2015; Pariseau and McCarter, 2016) have shown high correlations of seismicity with element failures in finite element simulations. The main lesson learned from these studies is one elaborated by Iannacchione et al (2005); deviation from normal activity is an early warning of ground control difficulty. For example, an abrupt increase in seismic event rate, or equivalently, an increase in element failure in finite element simulation of panel advance, is a cautionary indication for ground control. Present and past study results demonstrate the effectiveness of finite element simulations for mine design and early detection of potential ground control issues."

Jan 1, 2018

By Nic Slatalla

Acoustic emission monitoring techniques are a powerful tool for analysing deformation behaviour and fracture characteristics of rock samples under uniaxial loading. Uniaxial compression tests were carried out on three different types of sandstone for a better understanding of acoustic emission response with respect to rock deformation and damage develop-ment. All sandstone samples revealed congruent characteristic acous-tic emission patterns which correlated directly with distinct stress-strain stages. However, the acoustic response and development within the individual stages proved to be entirely different due to variations in their microstructure.

Jan 1, 2008

By Hamid Maleki

A geotechnical monitoring program has been implemented at Energy West Mining Company for enhancing site-specific evaluation of longwall stress conditions. This program consists of underground measurements at five locations in two neighboring mining districts located in the Hiawatha and Blind Canyon Coal Seams under moderate to deep cover. Within the last five years, additional measurements, including data on recorded seismic events and face conditions, have been incorporated into the data collection program together with detailed geologic mapping of longwall gateroads. In conjunction with the measurement program, the authors have completed detailed boundary-element stress analyses of the mine plans. Models have been calibrated using the data from in-mine instrumentations and then routinely used for evaluation of mine plans at depths approaching 2,600-ft. The work has improved our understanding of load transfer, seismicity and yield pillar performance. It has identified areas of potential increased stress levels at certain longwall face positions and provided guidance to measures that could be considered to mitigate the potential for these increased stress levels.

Jan 1, 2009

By Anthony T. Iannacchione

Longwall mining produces surface subsidence basins that affect streams by water diminution and contamination. These effects can ultimately impair the biological character of the plants and animal communities living in the streams. The combination of flow, water quality, and ecological effects threaten the environmental sustainability of longwall mining and, ultimately its social acceptability. Pennsylvania has developed new standards, released in 2005 and implemented in 2007, to help protect the commonwealth?s valuable streams from the detrimental effects of subsidence. These standards are aimed at eliminating environmental problems and will therefore help to make underground bituminous coal mining more sustainable. The engineering solutions necessary to comply with these standards are fundamentally affected by the geologic nature of coal-bearing strata, the existing in-situ stress conditions, and the ability of selected species to survive and adapt to changes in their environment caused by longwall coal mining subsidence. Needless to say, geologists, biologists, and engineers are all playing a pivotal role in developing prevention controls and recovery measures necessary to protect streams and sustain underground coal mining. The challenges facing scientists and engineers in sustaining the development of underground coal mining in Pennsylvania are examined through case studies. These challenges all arise from the subsidence effects of longwall mining. The key effects of subsidence, discussed through case studies, are: a) tension cracks, b) springs in headwater stream areas, c) stream gradients and subsidence basins, and d) stream compression ruptures and horizontal stress. All of these potential threats demonstrate the need for high-level scientific knowledge and innovative engineering solutions. One could argue that Pennsylvania?s stringent stream protection standards put the coal mining industry at a competitive disadvantage compared to other coal producing states. It is equally likely that compliance with these standards help to mitigate the effect of subsidence, thereby helping the coal industry achieve a sustainable future.

Jan 1, 2011

By Madan M. Singh

Mining under bodies of water such as oceans, lakes, rivers, streams, ponds, and other impoundments, is not a new technique. However, in the United States it has been fairly restricted to date. In order to recover the maximum amount of the nation's reserves, in the future, it is important that further mining under such bodies of water be planned. However, it is imperative that this is not done at the expense of danger to the nation's miners or appreciable property damage. If all the bodies of water are considered large, and it is assumed that these constitute a hazard when mining in their vicinity irrespective of their size and geometry, a significant percentage of the coal reserves are likely to be sterilized. How- ever, by adopting special mining plans and procedures, it may be possible to release reserves for exploitation that would otherwise be unmineable since the surface of bodies of water below which they lie are relatively small in size. In 1977, the Bureau of Mines issued Information Circular (IC) 8741, entitled "Results of Research to Develop Guidelines for Mining Near Surface and Underground Bodies of Water". This document was based on the work done by Skelly and Loy (under Contract No. H0252083) and K. Wardell and Partners (under Contract No. H0252021). How ever, these guidelines have limited application, because these did not (1) define the bodies of water of concern, and (2) take into account the nature of the strata being encountered. These guidelines assumed that all bodies of water which would be undermined were large. For the purposes of this discussion, water bodies may be divided into three categories, depending upon their potential to cause damage to the underlying mining activity: ? catastrophic ? major ? limited Bodies of water which pose the threat of catastrophic destruction in the mine, should there be an inrush, include oceans, large lakes, big inland reservoirs, and rivers that could flood the mine complete- ly in a short period. Those with major potential for damage would include lakes and streams which might present a danger to both life and property if not considered in the mining plans. Finite bodies of water which have a volume considerably smaller than the mine volume offer a limited potential for damage in the case of an inrush. These include flowing streams which have a relatively small rate of replenishment and which can be dealt with by pumping or isolation in the event of a breakthrough into the mine. Such bodies of water may be inconvenient and cause a temporary disruption of production, and could even cause some damage to equipment, but only in rare instances would personal injuries occur. The scope of this paper is limited to the exploitation of stratified mineral deposits with overlying -face bodies of water. Vein and dessiminate ore deposits are not discussed, nor are breakthroughs into adjacent mines in the same horizon. Overlying, water-logged strata also pose a serious threat to mining, but are not treated in this discussion. Pending further investigation these strata may be considered as bodies of water with catastrophic potential for damage, with the base of the strata being considered the bottom of the water body. When the body of water is large, so that it may cause catastrophic damage to the mine in the event of an inrush, the guidelines suggested in IC 8741 are applicable. In order to develop criteria and procedures for mining under smaller bodies of water, however, it is necessary that the nature of the strata disturbance due to underground mining be examined.

Jan 1, 1981

By Dr. Daniel W. H. Su

t is both an honor and privilege for me to nominate Dr. Daniel W. H. Su for the inaugural Syd S. Peng Ground Control in Mining Award. I can think of no better candidate than Daniel that is deserving of this award ? an award to recognize technical excellence in advancing ground control technologies [and] approaches. Daniel?s education and career spans over three decades. Having graduated from National Cheng Kung University in Taiwan in 1972 with a B.S. degree in Mining and Petroleum Engineering, he spent the next four years in the Taiwanese military and mining industry, before moving to the United States, where he enrolled in West Virginia University?s Mining Engineering Department. He received his M.S degree in Mining Engineering from WVU in 1978; then in 1982 became the first person to ever receive a Ph.D. in Mining from WVU. His thesis was titled, ?Development of Ultrasonic Techniques for the Measurement of In Situ Stresses?.

Jan 1, 2006

By Barry Voight

The law [ ] where [ ] is a measurable quantity such as strain and A and cu are empirical constants, describes the behavior of materials in terminal stages of failure under conditions of approximately constant stress and temperature. Applicable to intact rock and rock masses, the relation may be extended to conditions of variable stress and cyclic stress, and may be used to predict time to failure. Applications in rock mechanics include slope and excavation stability and various topics in ground control.

Jan 1, 1989

By John Rusnak

The Coal Mine Roof Rating (CMRR) is a practical rock mass classification system for use in design of mine openings. Data can be obtained for this purpose from exploration drill cores if simple geotechnical logging and rock mechanics testing is conducted. The CMRR is an excellent method to quantify rock characteristics for engineering purposes. It bridges the gap between geologic description and engineering design. The CMRR was utilized in the design of a 10,000 fl. long coal belt conveyor tunnel connecting an Eastern Associated Coal Corp. mine and preparation plant in Boone County, West Virginia. Data gathering and analysis techniques are discussed involving the calculation of the CMRR and its application in the design of the tunnel, which was driven through a thin coal bed zone. The preliminary findings have correlated well with actual roof and mining conditions encountered during driving the tunnel and it is concluded the CMRR is an effective method to utilize geologic data from exploration core holes for engineering analysis and design.

Jan 1, 1998

By Benjamin Mirabile

"Current and emerging practices to ventilate longwall gobs are prompting increased design and analysis of standing support requirements related to longwall mining. Specifically, additional design methodologies are being employed to evaluate standing supports in the #2 entry of a 3-entry longwall system.Numerical modeling will be used to evaluate the performance of standing support in the #2 entry between gobs of longwalls in the Herrin No. 6 seam. The performance of standing support in the #2 entry will be evaluated based on the following: (1) The effectiveness of standing support in maintaining an open airway in the #2 entry; (2) The interaction of standing support in the #2 entry with standing support in the longwall tailgate; and (3) Loading conditions of longwall pillars. Initial numerical modeling activities are focused on evaluating the roof to floor convergence in the #2 Entry and using the ground reaction curve concept for support design.Numerical modeling indicates that, like standing support in tailgates, supports in the #2 entry require some type of yield mechanism to withstand initial uncontrolled convergence. Numerical modeling also suggests that support density can be lower than that used in a tailgate support application. The numerical models used for initial investigation of support performance in the #2 entry are limited in their ability to evaluate support performance. The magnitude of uncontrollable convergence can be estimated with LaModel software. Near-seam conditions have not been investigated in this research since the LaModel software does not have the ability to evaluate inelastic rock behavior.IntroductionDuring the past three decades, many researchers have investigated standing support performance in longwall tailgate entries. Very little attention was paid to the middle entry of a threeentry longwall gateroad. As longwalls retreated, no personnel would travel the #2 entry, and the entry was considered part of the longwall gob. In response to recent mine disasters, regulatory agencies and operators have devoted more attention to these entries. Prior to the Upper Big Branch mine disaster, little or no secondary support was applied in these entries. Unlike secondary support in longwall tailgates, there is little empirical knowledge or quantified research specifically applied to secondary support in the #2 entry. This paper outlines initial steps used to develop a design methodology for secondary support in the #2 entry."

Jan 1, 2015