Search Documents

By David A. Newman

Severe roof control problems have plagued a West Virginia underground mine since its initial development in the late 1970's. Adverse roof conditions in the Eastern portion of the reserve result from a combination of mining: - perpendicular to the major principal horizontal stress direction, - near lineament intersections, - in areas where the ratio of horizontal stress to vertical stress exceeds 2.00 to 4.00, and - where laminated strata are present in the immediate roof. The focus of this study is to identify the engineering (mine orientation, roof safety factor) and geological parameters (lineament and horizontal stress orientation, horizontal to vertical stress ratio, and immediate roof lithology) causing poor roof conditions and to quantify their influence on projected mining conditions in the Western portion of the reserve Rose diagrams were used to illustrate the correlation between the orientation of eight hundred thirty-six (836) roof falls with that of forty-four (44) lineaments and the principal horizontal stress Similarly a composite map was used to demonstrate the relationship between roof falls and the ratio of horizontal stress to vertical stress The immediate roof strata across the property were categorized as either laminated or non-laminated based upon a thorough examination of one hundred sixty-two core logs. The presence or absence of fireclay, a rider coal, and carbonaceous shale was also noted because of the historic correlation with poor roof conditions. Rock strength and physical property tests were conducted on selected immediate roof strata recovered from coreholes drilled along the mains projected to the Western portion of the reserve Potential roof control problems in the Western reserve were quantified based upon the correlations developed by analyzing engineering and geological data The main conclusion is that laminated roof strata, the rider seam, and its associated fireclay will have the greatest influence on mining conditions. Roof problems attributable to horizontal stresses will not be as severe in the West due to an increase in overburden depth and corresponding decrease in the stress ratio. Recommendations are provided for mining orientation, the layout of mains and submains, panel location, and roof support based on intended service life.

Jan 1, 1999

By Jeffrey Whyatt

Mining coal in deep, gassy strata is difficult, particularly in deep mines of the west. Dynamic failure (bumps, bounces, etc.) is commonplace, particularly where strong sandstone strata are encountered in the overburden. The disaster potential posed by dynamic failure in these mines is examined and found to be significant. Recent trends in MSHA reportable bumping of deep western coal mines have been increasing. Recent clusters of bumps are explored, a number of which have ended badly. The mechanisms of these bumps and their interactions with geologic structures are explored. Significant progress in controlling these hazards depends on a full understanding of their interaction with geologic conditions. It is apparent that not all MSHA reportable bumps have the same mechanism. These reports describe bumping of pillars, rolling of ribs, outbursts of coal, heaving of floor, shaking-induced roof falls, etc. Progress depends on understanding the underlying mechanisms of these events, and then determining which are potentially active at a particular location. Designs and other protective measures can then be adapted and deployed appropriately. Explicit consideration of mechanisms also supports extrapolation beyond experience as design extends into new mine geometries, geologies, mining methods and increasing depth. Finally, the goal should not be only to design hazard out of mines, but also to provide assurance that this, in fact, has occurred. Pursuit of this goal has been taken up by a major NIOSH research project. The centerpiece of this project is development of a Dynamic Failure Control Program to monitor evolution of dynamic failure hazards with changing geologic conditions to assure that control and protective measures are appropriately deployed.

Jan 1, 2008

The effects of corrosion upon the load bearing capacity and ultimate tensile strength of galvanised friction bolts were determined. Corrosion rates were measured by overcoring of the reinforcement elements in situ. Overcoring was achieved at several sites using a specifically designed overcoring drill rig. This rig has the capacity to drill up to 3.0m long 140- diameter core in any orientation and up to a collar height of 7.0m. The recovered core and friction bolt elements were pull tested in the rock mechanics laboratory at the WA School of Mines (WASM) in order to determine their load-displacement characteristics for various embedment lengths. The friction bolt elements were then analysed for rates of corrosion and tested for their ultimate tensile strength. Relationships were formed between these data and the environmental conditions to which the friction bolts were exposed, in order to determine the major factors affecting the corrosion process and how they affect bolt performance.

Jan 1, 2005

By Clifford J. Roblee

In this paper, various seismic indicators are evaluated for ability to discern fractures induced into a rock mass by blasting. This is accomplished by presenting results from in situ crosshole seismic studies performed prior to and after a sequence of controlled blasts within limestone and dolomite rock near Austin, TX. Indicators investigated are compression (P-) and shear (S-) wave travel times, first peak and maximum amplitudes, first arrival rise rate, and the linear spectrum of the received signal. Compression wave travel time yielded the most consistent results, while the various amplitude indicators yielded the poorest results for the equipment configuration utilized. In addition, this study documents magnitudes of change in seismic measurements which occurred following blasting. Both P- and S-wave travel times exhibited a wide range of variation due to blasting. Near blast centers below the surficial fractured rock, velocity decreases of about 10% were noted, significantly less than the 50% decrease observed for previously fractured near-surface rock through which the explosive energy was vented. Signal amplitude measurements also varied in magnitude but were less consistent.

Jan 1, 1989

By Larry Howe

Second, or retreat mhng with Mobile Roof Supports (MRS) has now been part of coal mining in the United States for a decade Their utilization has evolved into mining applications which vary in seam heights from 38 inches to 170 inches, and overburden depths from outcrop to beyond 1200 feet This paper will detail the pillaring plans, lift sequences, and mnchky utilized in these operations and the rational for the plans A comparison of the current productivities achieved will be outlined

Jan 1, 1998

By B. N. Whittaker

The paper briefly reviews the type of support and stability problems encountered in mining tunnels in U.K. Carboniferous rock conditions, particularly the Coal Measures where almost all such tunnels are located. Stability prediction of mining tunnels is discussed and a computer-based model which deals with stratified rock conditions is described. Various schemes for monitoring the stability of mining tunnels are examined and the application of the results discussed. Comparisons between predicted and measured Closure values are presented for a major Coal mining tunnelling project at Selby in the North Yorkshire Coalfield. Conclusions are drawn concerning the application of the present prediction technique together with the importance of underground monitoring. Examples of different types of mine tunnel stability problems encountered in the U.K. Coal Measures are discussed and comments made on the secondary effects of tunnel peripheral rock weathering and corrosion of the associated support systems.

Jan 1, 1987

By David Dye

Good morning, everyone, and thanks Syd for that fine introduction. I am honored to be here to help you celebrate 25 years of advancement and success in the important field of ground control. I would also like to recognize Dr. Peng for his significant contributions in longwall mining and ground control. His contributions have had a major impact on improving safety and reducing fatalities in America?s mines. Thank you, Dr. Peng, for the important work you have carried on throughout the years. Many miners are alive today because of your dedicated work to protect them.

Jan 1, 2007

By Xun Luo

In this paper we report on the use of microseismic monitoring techniques to investigate the fracturing process associated with longwall mining. The study was carried out at three mines in Australia and concentrated on some major concerns of the mines, such as failure patterns and growth rate associated with mining progress, their implications to water ingress and gas emissions, caving processes in the goaf and precursors of roof falls. The results have shown that a zone of shear fracturing has occurred further ahead of the longwall face than predicted using conventional longwall geomechanics theory. Failure patterns in the roof and floor vary from mine to mine and this appears to be dominated by geological structures. The reaction of faults, the formation of fractures which allow gas emissions and precursors roof falls have also observed. Results from this work have opened up new understanding of longwall caving processes and proved that microseismic monitoring is a very useful technique for studies of longwall geomechanics and hazard controls.

Jan 1, 1998

By Gennaro G. Marino

Site conditions at several shallow room and pillar mines in Illinois are described and compared with the charac¬teristics of the subsidence profiles at the ground surface. The shape and magnitude of the subsidence profiles were found to be closely related to the thickness of the soil and rock over-burden the percent extraction of the coal, and the shape of mine pillars. The room and pillar mines were located at a shallow depth (from 112 to 220 ft), beneath flat to gently rolling terrain. Thickness of the coal seams ranged from 5 to 9 ft and at all sites was underlain by underclays. This information has been developed in order to improve techniques for evaluating the subsidence potential at sites within the Illinois coal basin. he results presented form a small portion of the work carried out by the University of Illinois with Illinois Abandoned Mined Lands Councils and the U. S. Bureau of Mines at the Minneapolis Research Center in Minnesota (Marino and Mahar, 1985). Presented in the paper are the modes of mine failures observed for Illinois room and pillar mines, an overall summary of the site geologic and mining condi¬tions, case histories of each mode of failure, a comparison of sag profiles, and then an empirical relationship between the site conditions and the maximum sag subsidence. The most ideal case histories are presented to illustrate fundamental behavior. A brief of the Paper is given in a summary and conclusions section.

Jan 1, 1984

By Kenneth L. Johnson

The effects of underground longwall coal mining on flow in perennial streams within the Pittsburgh seam basin were evaluated. Four streams above four different longwall mines were studied. Overburden depths at the study sites ranged from 500 to 600 feet. At all four locations, premining streamfow measurements were made to establish baseline flow conditions. Measurements were then repeated at each location after the longwall face passed beneath the stream. At one location, in which the longwall panel axis was roughly parallel to the stream, the streamflow was monitored as the longwall face advanced. Measurements at this location showed that temporary flow reduction occurred as the face advanced underneath; however, after the tensile portion of the traveling subsidence profile passed, this effect was lessened. At two of the sites in which the stream was roughly perpendicular to the panel axis, postmining streamfow increased across the panel and decreased over the development headings, such that the net lateral change in streamflow across the fully subsided panel and associated development headings was small compared to the measured flow.

Jan 1, 1997

By James M. Kramer

This paper introduces an analytical approach for the determination of the vertical stress in the chain pillar system between two adjacent longwall panels. The development of this approach is based on the principles of fracture mechanics and superposition. Some empirical formulae have also been incorpomted into the development of the mathematical model. The mine entries and longwall gobs are treated as Mode I cracks in an infinite plate while the resistance of gob material and the characteristics of the pillar yield zone are considered as the distributed forces on the surface of the cracks. An user- friendly computer program has been developed to facilitate the calculation involved in this task. This approach is as accurate as the numerical analysis methods but requires much less expertise and computer hardware and software to apply

Jan 1, 1998

By Hakan Gurgenli

Many coal seams have weak shale immediate roofs that cause ground control problems. Therefore, it is important to know the properties of these shales so that preventive measures can be developed in advance. However, it is sometimes hard to understand this rock type due to its unpredictable behavior. A good example of this situation is found in two shale coal mine roofs located in the Illinois coal basin (Herrin No. 6 seam). Although, these mines are located very close to each other, one of them has many roof falls, whereas the other has no measurable ground control problems. The aim of this paper is to explain why and how one shale roof behaves worse than the other. Laboratory tests, including point load strength index, slake durability index, moisture activity index, weatherability index, water content determination, swelling strain and x-ray diffraction tests were performed to analyze the shale properties. According to these analyses, some useful correlations were found between the engineering properties, moisture-sensitivity indices, and weathering properties. Finally, mine and support design considerations based on the test results were discussed and recommendations to prevent ground control problems were given.

Jan 1, 2006

By Steve P. Signer

A study of rock support interaction mechanics was conducted by the U.S. Bureau of Mines at the Jim Walter Resources No. 7 Mine, Brookwood, AL. Bolt loads and entry deformation were monitored at four sites in a tailgate roadway. Two sites were areas supported by fully grouted resin bolts, and two sites were supported by tensioned bolts that used resin-assisted mechanical anchors. The yield capacity of the tensioned bolts was 37 pct higher than that of the grouted bolts. To monitor loads, instruments were mounted on 16 bolts, which were installed during entry development in the standard bolt pattern. Additional instrumented bolts were installed as supplemental support just prior to the headgate pass of the first longwall. Instruments to measure roof movements included three-point roof extensometers and convergence stations. Readings were taken during section development and as each longwall panel passed the test area. The fully grouted bolts showed localized loads that were higher than loads on the tensioned bolts; however, overall loading magnitudes were similar. Many sections of the fully grouted bolts passed the yield point of the bolt steel (98 kN or 22,000 lb). However, the maximum strain measured at any loca¬tion was 50 pct of the ultimate strain, and there was adequate bolt length to transfer the high loads into the rock. Significant bending was detected at many points along the length of the bolts and seemed to be the most significant mechanism in support-rock interaction. Loads on the tensioned bolts did not exceed the yield point of 160 kN (35,000 lb). Entry deforma¬tion, supplemental bolt loading, and general entry degradation appeared to be slightly less at the tensioned bolt sites. Local geology and in situ horizontal stress were also observed to affect con¬ditions at the test sites.

Jan 1, 1993

By Vladimir I. Klishin

Complex method of ruling of rock pressure is considered in conditions of rapid roof subsidence. The purpose of this method is elaboration of emergency devices into hydraulic props. Also method of unloading of solid roofs is worked out. An analysis of means of protecting hydraulic props of powered supports 6om dynamic loads made it possible to divide them into four classes according to principle of operation: emergency, operating hm an increase of pressure; emergency damping; emergency, operating according to the "plastic element" principle; inertial emergency, operating hm dynarmc loads. It was established that the overwhelming 'majority of designs of the first three classes of emergency devices (EDs) are based on !mditional approaches, which exhausted their possibiiities of high-speed response. Delay on their opening is caused mainly by inertia of the moving locking parts. In our opinion, the most prospective are EDs using the inertia of the moving locking parts for depressurizing the piston cavity of the hydraulic prop with a minimum delay (inertial EDs). The essence of the designs of EDs having an inertial principle of action is that into the hydraulic prop containing movable and immovable elements is additionally introduced a spring-operated contracting support, which is installed on the movable element. Under dynamic loading of such a hydraulic prop hm the roof, the support moves relative to the movable element, performing the role of an inertial mass, which leads to instantaneous depresswization of the piston cavity of the hydraulic prop. Technological measures for unloading of solid roofs consists in creating of long oriented cracks in rock massif. Description of method for creating cracks, demanding equipment and means for cone01 the progress of splits are included. Also technological schemes for realization of the method of saving underground mines and rock mass are included. The results of experimental realization of this method on the Kuzbass and Poland coal mines are also included.

Jan 1, 1997

By Joe E. Bryan, John P. McDonnell

"Underground mine rib stability is an ongoing safety issue in all mining applications. Rib-related accidents present at least as many problems as roof-related ground control. Underground coal mine rib safety is continually emphasized as a primary safety concern at every mining operation. The application of rib support materials is increasing as more difficult mining conditions are experienced due to deeper cover, more variable depositional environments, thicker seam heights, and multi-seam mining effects. As the coal seams become thicker, the need for rib control increases. A variety of rib control methodologies has been documented and research continues on mine design methods and support techniques to reduce or eliminate rib-related accidents.This paper presents an alternative rib bolting technology using proven conventional rib support systems that allows mine personnel to more efficiently install rib support during development operations. This alternative rib bolting method allows for additional rib support with a single support installation.INTRODUCTIONRib control continues to garner the watchful eye of both concerned operators and government officials due to many factors: inherent safety within entries and crosscuts, actual rib stability history, safety improvement, cost control, improved mining methods, and maintaining production goals. As demonstrated through many years of actual practice, desired outcomes can be achieved by scrutiny, innovation, and combining improved practice methodologies.Rib surface control continues to be a necessary part of the production process. However, production and safety issues persist at the point of installation using current control apparatuses and methods to install rib controls. Among others, current issues of rib control are quantity of bolts required, overall time required for installation, ease of apparatus installation, flexibility of the system for appendage installation and operator exposure. A need exists to decrease the time miners spend installing rib control apparatuses, while increasing the safety of such installation processes. At present, installing rib control devices (primary rib bolts, plates, mesh, and, in most cases, secondary rib bolts and plates) is performed in a very congested area and is time-consuming process at the primary coal-winning area: the face. The MatLok system addresses these problems."

Jan 1, 2015

By Eric Westman

Ground control problems caused by multiple-seam interaction frequently sterilize coal reserves. Interaction mechanisms differ for overmining and undermining and are controlled by mining, spatial. and geologic conditions at each site. A multiple-seam interaction analysis software program, UGLY (Uppersearn Gateroad Longwall Stability), has been used to evaluate sterilization of coal reserves due to overmining at three locations. Four case histories were reviewed to determine the effectiveness of improved ground control in mitigating interaction effects.

Jan 1, 1997

By T. P. Mucho

Strata behavior and support performance were evaluated in a longwall tailgate test area at the Eagle Nest Mine near Van, WV. The mine operates in the Eagle coalbed which ranges in height from 4 to 6 ft (1.2 to 1.8 m) on the mine property. Rugged topography results in rapid changes in overburden which ranges from 200 to 1200 ft (61 to 366 m). The immediate roof at this mine transitions from sandstone to shale. In some areas the sandstone appears to be massive while in many locations it is highly laminated, fossilized, and interspersed with coal streaks. Horizontal stress levels appear to be sufficient to create instabilities in the roof in some locations, especially where the roof is thinly laminated. Traditionally, hardwood cribs have been used at the mine to provide secondary support for longwall tailgates; Strata Products' Hercules cribs are installed on 8 ft (2.4 m) centers staggered left and right in the tailgate entry. In a 250 ft (75 m) tailgate test area, however, cable bolts were installed in lieu of cribs. The bolts were 12 ft (3.6 m) long tensionable cables anchored with 5 ft (1.5 m) of resin. Four cables were installed across the entry and rows were spaced on 6 ft (1.8 m) centers. Primary roof support was maintained in the vicinity of the test area using 42 in (1.1 m), grade 60, No. 6 (19 mm diameter) resin bolts installed on 4 ft (1.2 m) centers through T-2 channels. The cable test area was located under a stream valley in an area of relatively shallow overburden. Strata instabilities consistently had been associated with the stream valley in both the Eagle and the overlying Powellton coalbeds. In an effort to further expose the cables to the most difficult stress conditions available at the time of the test, the specific site chosen was directly beneath a barrier pillar remaining in the upper Powellton mine (approximately 150 ft (45 m) of interburden separates the two coalbeds).

Jan 1, 1996

By Swapan Bhattacharya

United States federal and state regulatory authorities require underground mine operators to adopt adequate measures to minimize material damage to the surface caused by nine subsidence. This paper presents an approach to define and determine the extent of material damage due to subsidence from underground coal mining. The basic steps involved in the development of adequate criteria have been enumerated together with the approaches and methodologies used.

Jan 1, 1984

By Takashi Sasaoka

Chain Conveyor Cutter (CCC) is a chainsaw-type machine and originally developed for the construction of underground walls and/or ground improvements. CCC was developed from the accumulated technology of coal mining, combining the cutting technology of a shearer and the fuctions of chain conveyor. The CCC can cut harder soils and soft rocks, and vertically mixes the cut soils/rocks with cementing material selected through the discharging port installed at the bottom of the machine. In Indonesia, highwall mining trials have already been conducted in several coal mines. However, full-scale and regular operations have not been done yet due to the ground and machine control issues from their geological conditions. In order to overcome these problems, the application of CCC to highwall mining systems was proposed, and its applicability and technical issues to be solved were investigated in this research. This paper discribes the characteristics of CCC system and discusses the application of CCC to highwall mining systems.

Jan 1, 2012

By Gary B. Petersen

The author has developed a seven-step process called the Applied Rock Mechanics (ARM) Protocol that the author has used to solve numerous roof stability problems in mines throughout North America since 1975. It is a practical evaluation process using trained observation, innovative data collection instrumentation, video borehole cameras, analytical processes, and controlled testing methods that have become highly effective in solving ground control problems in every type of underground mine. This paper will describe each of the steps of the protocol and how the rock mechanics engineer applies them to resolve a typical ground control problem.

Jan 1, 2012