Search Documents

By Christopher Mark

A coal burst is defined as the sudden, violent ejection of coal or rock into a mine opening. Coal mines in the North Fork Valley (NFV) of Colorado?s Gunnison River have a long history of coal bursts in a wide variety of settings. These have included longwall and room-and-pillar, development and retreat, and single- and multiple-seam mining. In contrast to other coalfields, where bursts are typically associated with strong, massive sandstone and extremely high stress, many bursts in the NFV have occurred beneath shale roof and some distance from the most highly stressed locations. The goal of this paper is to attempt a systematic study of the entire burst history in the NFV, in order to gain insight into their characteristics and causes. The primary sources of information are the reports of investigations conducted by the Mine Safety and Health Administration (MSHA) Roof Control Division over the past 15 years. This paper provides details on the geologic mapping conducted as part of these investigations, as well as a regional plot of burst locations using a Geographic Information System. The mapping indicates that many of the NFV bursts have been associated with structural features, including low-angled faults and well-defined zones of high-density jointing that exhibit little or no displacement. Some of these features appear to extend for several miles, impacting more than one mine.

Jan 1, 2012

By T. P. Mucho

Over the past several years, two types of roof control problems have been en- countered at Beth Energy's Eighty Four Complex mine in Southwestern Pennsylvania. These problems have been (1) poor roof conditions encountered while advancing submain entries and longwall panel entries and (2) deterioration and failure of long- wall gateroads, principally the tailgate entry. This paper discusses the efforts by mine personnel to analyze the origins of the various attempts to-deal with the problems, and the success (or failure) of these efforts. Highlighted are the use of various common roof Control materials, variations in mining techniques, cementatious pillars, and changes in pillar design using yield and abutment pillars to address these problems.

Jan 1, 1986

By Ken Mills

A program of stress change and roadway deformation monitoring was undertaken to measure the forward abutment load distribution about a retreating longwall panel at Dartbrook Mine. The results of this monitoring allow roadway conditions observed at various stages of mining to be ranked according to the estimated vertical stress they have experienced. This ranking also provides a means to predict and visualise future roadway conditions at various stages of mining. This paper presents the results of the monitoring and describes the approach developed to predict future roadway conditions. The monitoring results show the vertical stress distribution associated with the front abutment from a longwall goal decreases exponentially away from the goaf edge. The vertical stress distribution peaks at the goaf edge at 5 to 6 MPa stress increase and decreases to 1 MPa within 50 m becoming imperceptible beyond 100 m By scaling this measured distribution to reflect the loading environment, the vertical stress can be estimated for different overburden depths and different stages of mining. Photographs of roadway conditions at particular vertical stress levels provide a way to visualise roadway conditions at various stages of mining in the future

Jan 1, 2000

By Yuanwci Shi

This paper discusses the results of research on the interaction between roof strata and shield supports including the active and passive supporting functions of the shield supports which prevents roof strata separation; pressure distribution on the canopy and under the base plate as measured in the laboratory and underground; comparison between various shield structures regarding their effectiveness on roof and floor control; and determination of optimum support capacity under given geological and mining conditions including hard-tocave roof

Jan 1, 1997

By Jon Bowler

Daw Mill Colliery, UK Coal, near Coventry in England, mines the Warwickshire Thick Seam at 800 m/2500 ft depth using longwall retreat with gateroads supported by rockbolts. Over the last eight years the mine has worked longer and wider panels with extraction heights of over 5 m. Recently the mine has experienced high deformation conditions principally from the rib sides resulting in operational issues and production delays. Investigation of rib deformation was undertaken using new inspection and measurement techniques, including systematic laser surveying, and improved rib support consumables were developed and introduced. A new rib trussing system using textile webbing has proved very successful.. A rib support management system was also developed and introduced for face retreat. This allowed rib support to be more effectively managed both for production and safety. For the current developments, new 28-mm-diameter roof and rib bolt systems have been introduced and rib bolt length has been increased to 3 m, with the aim of achieving gateroad stability over the life of the panel. Significant reductions in roof and rib deformation have been confirmed by the latest monitoring results. These ground control innovations are allowing Daw Mill?s potential to be realised. Production from 302?s face in 2008 set new UK and European records. However the support enhancement process continues and further innovations are planned.

Jan 1, 2009

By Jiacheng Wang

The current state of thick seam coal mining methods is illustrated in three typical cases of thick seam longwall mining, each pointing out the outstanding achievements in top-coal caving mining and large cutting height mining in China. At the same time, based on current thick seam mining practices in China, some problems urgently need to be solved. These include improving the recovery ratio of coal reserves, determination of overburden strata pressure, shield support selection, supporting methods for large cross-section in-seam roadways, top coal bulk flow theory, and gas flow and control technology. In addition, the rational production capacity should be studied from both economic and technological perspectives in order to optimize coal recovery and efficiency.

Jan 1, 2011

By Vasundhara

Underground coal mining in soft floor environments has often led to strata control problems ranging from small scale issues such as floor heave which disrupts traffic and ventilation, rib spalling and induced fractures in pillars, through to large scale instability and long term subsidence. Past investigations of the problems encountered in Newcastle Coalfields of New South Wales, Australia, have revealed that the soft floor unit comprises of claystone which is very sensitive to moisture. It is prone to swelling, reduction in stiffness and loss of strength in the presence of moisture. Long term stability of mine panels in such an environment is governed by the extent of deterioration of the floor strata. The paper reports the field investigations conducted at Cooranbong Colliery to assess the extent of softened floor zone in the roadway and under a pillar.

Jan 1, 2001

By David A. Newman

Strength and physical property testing of coal is conducted regularly by the Arch Mineral Corporation as part of reserve exploration. Pillar design and mine layout are the primary applications for the coal strength data. Distinct differences in pillar behavior were observed during longwall mining at a mine in Southeastern Kentucky. Horizontal and vertical variation in both triaxial and uniaxial compressive strength was observed within the four (4) benches of the Harlan seam. Similarly, geographical variations in coal strength were noted across the Harlan seam reserve. During the past three decades substantial research efforts have been focused upon coal pillar behavior and the refinement of pillar design methodologies. Ironically, little attention was directed to integrating the variability of coal strength into pillar design. The authors examine, through the presentation of case history data, i) typical industrial practice with respect to establishing a database of coal strength for use in pillar design and stability analysis, ii) approaches in which the observed variation in strength in the Harlan seam is integrated into pillar design and stability analyses, and to iii) propose standards for coal cube testing

Jan 1, 1993

By Peter Cain

The Phalen Colliery in the Sydney Coalfield is extracting the 2.6 m thick Phalen Seam by the panel and pillar longwall retreat method. Abandoned workings occur in the Harbour Seam 140 m above and overlie the Phalen Colliery. Parts of these workings are flooded, and pose a number of questions relating to the safety of operations in the Phalen Colliery. In order to answer some of these questions, the Cape Breton Development Corporation re-entered an abandoned non-flooded roadway in the Harbour Seam directly above a retreat panel in the Phalen Seam to allow the deployment of instrumentation to monitor interaction effects. Fifteen monitoring sites, each 4.5 m apart, were installed in the 5 East Top Level after it had been re-entered and made safe. Each monitoring station included a vibrating wire strain gauge piezometer and a potentiometric extensometer. The piezometers were attached to rock bolts anchored into the floor and were connected by a flexible standpipe to a constant head apparatus. Variations in hydraulic head due to subsidence were monitored to determine subsidence. The extensometer units were mounted on rock bolts anchored into the floor of the roadway beneath the ribside and monitored ground strains. The instrumentation was capable of remote reading in the event that access to the site was restricted after installation. This paper describes the instrumentation, the installation programme, and some preliminary results.

Jan 1, 1993

By Y. L. Sun

The feasibility of using the ultrasonic wave attenuation method for measuring in-situ stress is examined theoretically and experimentally. The theoretical analyses show that for a given rock type the relation between stress and attenuation coefficient ratio can be approximated closely by second-order polynomials. Combining the elastic and statistical theories, the magnitude and direction of the existing principal stresses can be predicted by using the relations between stress and attenuation coefficient ratio obtained in the calibration of core specimens. Several experiments are conducted in the laboratory on two types of rock. The experimental study consists of two parts: the attenuation-coefficient measurements in core specimens under uniaxial stress and the attenuation coefficient measurements in boreholes drilled through blocks of sandstone and limestone subjected to uniaxial compressional stress. Compressional waves are used exclusively in the measurements.

Jan 1, 1989

By Hui Chen

The paper describes the use of a physical model technique to investigate the failure modes of mine tunnels with reference to the in situ stress field. The characteristics of stratification commonly encountered within UK coal mining conditions have been taken into consideration. The investigation has indicated that the weak floor strata in coal mining tunnels, under the action of high rock stresses, will be subject to the floor lift problem in both predominantly horizontal and vertical stress fields. However, the failure mode and mechanism varies between the two stress field patterns. In the predominantly horizontal stress field, the tunnel floor tends to fail by gradual bending of the laminations, whilst in the predominantly vertical stress field, the floor tends to fail by a shearing action with the failed material lifting in the form of a block. The failure mechanism is discussed with reference to mechanics theory.

Jan 1, 1993

By William Kendall

INTRODUCTION Stillwater Mining Company, with its two underground, hard rock mines in South Central Montana, is the largest primary producer of palladium and platinum in the Western Hemisphere. Platinum Group Metals (PGMs) are mined from a specific zone within the Stillwater Complex, a layered mafic/ultramafic igneous intrusion, named as the J-M Reef. Over much of the J-M Reef, the economically minable, mineralized horizon is contained at typical horizontal widths of 6.5 ft to 8 ft wide. This feature of narrow mining widths has made it challenging to safely and effectively mine these areas of the J-M Reef using mechanized cut and fill and sublevel sill development mining methods. Mechanization of most or all of the steps of the mining process is important to Stillwater in the continuous pursuit of high standards in safety and health. Mechanized bolting within the J-M Reef ore production headings is an important piece of reaching these objectives. In general, metal/non-metal mining requires varied mining techniques, as compared to more traditional bedded mineral/resource deposits. Narrow vein mining is a selective mining technique that generates a minimal amount of waste material while obtaining the more valuable ore deposits. Drilling and bolting in narrow vein mining has traditionally been performed with air-powered, hand-held ?jackleg? equipment because mechanized equipment is, typically, too large for the selective narrow vein techniques. In addition, traditional hand-held pneumatic equipment provides significant flexibility for small-opening, narrow-vein developments, reducing waste rock handling and improving ore recovery management. The hand-held equipment is also relatively inexpensive to purchase. Due to its simplicity, it is also relatively easy to train operators to use hand-held equipment. Hand-held equipment has been routinely used to safely install ground support and to develop production faces in hard rock mines for many years. Although it is effective, the hand-held equipment requires operator exposure to certain inherent hazardous conditions in the active face/development mine areas. These include falling rock, tripping hazards, bending/twisting/lifting hazards, high noise levels, and chemical fumes from the hammer exhaust. Based on health and safety statistics from the Stillwater mines, operation of the rotary-percussive hand-held equipment adversely affects the long-term health of the operator?continual jackleg operation frequently results in long term damage to hearing, shoulders, arm and wrist joints, and back injuries. This reduces the quality of life for the operator and also results in higher personnel turnover rates for the mining company.

Jan 1, 2014

By Peter Zhang, Gary Deemer, Rod Lawrence, Scott Peterson, Scott Wade, Mike Mishra, Rick Smith, Robert Bottegal, Ed Zeglen

"Thinly-laminated silty shale that falls like ""stack rock"" is always difficult to support in underground coal mines. With thin laminations of 2.5 to 52 mm (0.1 to 2 in) thick and weak bonding between laminations, the roof is much weaker under horizontal stress than under vertical load. Buckling of thin laminations and cutters are common signs of initial failure for this type of roof. When a roof fall occurs, it is mostly above the primary bolted horizon with a fiat top and steep breaking angle above the pillar ribs. Because silty shale is brittle, roof falls mostly develop without significant roof sagging. With thick, laminated silty shale, it is difficult to build a strong solid beam with short primary bolts. Longer bolts, straps, and supplementary cable bolts are required. Since installation of longer primary bolts in low seam mining is operationally inefficient, supplementary bolting is important to maintain overall roof stability. The bolting plan should also be chosen based on the geologic hazard map, which indicates the distribution and thickness of laminated silty shale, as well as the transition areas.To effectively support the thinly-laminated silty shale roof, an area with the same type of roof in a low seam mine was monitored for approximately four months. The mine had experienced roof falls while using different bolting systems and mine orientations in past years. The roof support in the area was studied through geologic mapping, roof scoping, and testing of different bolting plans. This paper presents the roof failure characteristics of the thinly-laminated silty shale, the correlation between failure and geologic condition, an evaluation of different bolting plans, and the requirements for primary and supplementary bolting for the silty shale roof.INTRODUCTIONThinly-laminated silty shale that falls like ""stack rock"" is always difficult to support in underground coal mines (Peng, 2007). With thin laminations of 2.5 to 52 mm (0.1 to 2 in) thick and weak bonding between laminations, the roof is much weaker under horizontal stress than under vertical load. Buckling of thin laminations and cutters are common signs of initial failure for this type of roof. When a roof fall occurs, it is mostly above the primary bolted horizon with a fiat top and steep breaking angle above the pillar ribs. Because silty shale is brittle, roof falls mostly develop without significant roof sagging. In low seam mining, it is difficult to install longer primary bolts, so supplementary bolts have to be installed to maintain overall roof stability. To effectively support the thinly-laminated silty shale roof, an area with the same type of roof in a low seam mine in western Pennsylvania was studied for approximately four months."

Jan 1, 2010

By Yundong Ma

In this paper the dynamic process of rock deformation and failure in the roadways of the #9 coal seam, Wuhushan Coal Mine by was simulated using the software "Rock Failure Process Analysis System (REPA)" [I]. Based on the simulation results, this paper analyzes the failure process, characteristics and weighting of the overburden as the longwall retreat mining proceeds. The roadway's behavior including deformation characteristics, failure mechanisms, stress distribution in the surrounding rocks and the effects of various support systems on roadway stability were analyzed and studied. While simulating the rock failure process with REPA, the model stresses can be obtained through two approaches: (1) the stress is reflected by the grayscale of pictures in the model failure process and (2) the model stress can be obtained by muti-element information, which is one of the commands in RFPA system. Data files of stress can automatically be created, and curves of stress and displacement of each element can be displayed in each step of computation. Keywords: Rock Failure Process Analysis System (RFPA); roof control; roof to floor convergence; combined support

Jan 1, 2005

By Liang Dong, Jinxuan Liu, Biao Qiu, Jing Chai

"The Cenozoic unconsolidated strata in the east area of China are composed of clay, sandy clay, fine sand, hardpan, etc. Numerous shafts of the coal mines in these areas have been damaged in various degrees since 1987. The main reason for this disaster is the vertical additional stress on shaft caused by the subsidence of the thick unconsolidated strata. In order to monitor the subsidence deformation of the unconsolidated strata, a sensing network system with multiplexed Fiber Bragg Grating (FBG) for monitoring settlement deformation of the unconsolidated strata in deep borehole is proposed. The field monitoring results show that, soil layers settle or expand with decrease or increase in ground water levels. The thick hardpan generates the main compressive deformation. This FBG strain monitoring method can take place of traditional ground water measuring method. This system is stable and reliable, and the monitoring results can show the subsidence deformation of different layers, which has significance for the predictive maintenance of the shafts.INTRODUCTIONSince 1980s, a specific geologic hazard has occurred frequently on the coal mine shafts in eastern China: non-mining-induced shaft deformation, involving up to 100 shafts located in Jiangsu, Shandong, Anhui and Herran province, distributed in Xuzhou, Datun, Huainan, Huaibei, Yanzhou and Yongxia coal fields. This kind of geologic hazard can lead to shaft wall deformation, water infiltration, cage stuck, water-sand burst or shutting down of coal mines, which seriously risks the coal mines. Zhangshuanglou coal mine, Haizi coal mine and Linhuan coal mine shut down for 2-8 months due to this hazard (Chen, 1997; Cui, 1998). The main reason for this geologic hazard is the subsidence of the super thick unconsolidated strata (Liu et al., 2007; Xu et al., 2006).An innovative structure health ·monitoring and damage estimation method has been developed in recent years, i.e., optical fiber smart material and structure (Nobuo, 2002; Wang et al., 2000). A Fiber Bragg grating (FBG) sensor is a device that can transfer the change of the measured strain or temperature to the change of Bragg wavelength. One of the most important applications of FBG sensors is to monitor the internal stress and strain distribution of material and structure (Philipp et al., 2000; Ansari et al., 1998). Compared to traditional electrical sensors, FBG sensors have many advantages; they are adaptable to harsh environments, abrasion resistant, immune to electrical magnetism (EM) interference, safe and reliable. They also offer integrated sensing and transmission on a single fiber, have simple structure and are convenient to use, which satisfies the requirements of long distance, distributional and long term use in monitoring mining and geotechnical engineering structure. Due to such advantages, the FBG sensor has already been applied in petroleum engineering (Kersey, 2000), rock mechanics testing (Cornelia et al., 2003; Yang et al., 2007; Wei et al., 2008), physical simulation experiments (Chai et al., 2007; Chai et al., 2006; Zhu et al., 2008; Li et al., 2008; Chang et al., 2008), strain sensor (Li et al., 2007; Chai et al., 2008) and construction structure damage diagnosis (Dong et al., 2004; Kerrouche et al., 2008; Whitten et al., 2001)."

Jan 1, 2010

By Rob Thomas

Main gate roof control during longwall retreat is subject to a significant increase in horizontal stress and risk. The implementation and management of an appropriate roof support design is as a result, an imperative requirement for any longwall mine and must in addition to the likely consequences of a roof fall, also consider the variables of the geotechnical environment, associated support costs and practicalities. This paper will therefore summarise a number of recent advances in main gate roof control in the Australian coal industry. Points considered include; (i) the ?Longwall Acceleration? concept, (ii) macro-scale horizontal stress notching, (iii) micro-scale horizontal stress notching, (iv) bedded versus laminated roof types and (v) the type of cable reinforcement used.

Jan 1, 2006

By Shengli Yang

Solid backfill mining, as a green mining technology, has the advantages of a higher resource recovery, less damage to the environment and the ability to dispose of waste underground. It has been applied successfully in the Xingtai and Xinwen mining areas in China. Strata behavior and the movement of overburden strata in this mining method are very different from fully mechanized longwall mining, which results in a natural caving, because the gob is filled with waste rock, fly ash and other backfill material. The results of field measurements showed that the periodic weighting interval of the main roof is longer; the magnitude of periodic weighting is smaller; the peak and zone of influence of the front abutment pressure are smaller than those in fully mechanized mining; that major deformation of mine roadways occurs within the influence zones of the abutment pressures; that the falling space of immediate roof is smaller, with the lower portion falling more sufficiently than the upper; that the main roof subsides slowly; and that the falling height of the overlying strata is greatly reduced.

Jan 1, 2011

By Duk-Won Park

A vast majority of the operating longwall sections use shield-type face supports to provide ground control in the United States. As a co-operative research program between the University of Alabama (UA) and Jim Walter Resources, Inc.(JWR), a joint research program is underway to study interaction of shields with surrounding rock masses. A series of analyses on the response of shields are performed using monitored data at a longwall face in a deep coal mine. In this paper, various effects of parameters, such as leg pressure, setting load, developing load, maximum loading rate, pressure in capsule, and convergence between canopy and base, are discussed and recommended as stability indices. A microcomputer program is being developed for instantaneous interpretation of the shield monitored data, and for giving warnings of potential problems. The preliminary results define the effects of the setting load, developing load, and rate of developing load or leg closure rate. The objective of the study is to understand the shield characteristics and their interaction with surrounding strata in real time, then develop a reliable program for maintaining longwall stability.

Jan 1, 1992

By Rob Thomas

Adequate load transfer is considered essential for optimum ground support and is increasingly important in weak roof and/or high stress environments. If adequate load transfer is achieved not only can this have a positive impact on the resulting roof behavior, but it may also allow the use of lower and hence more economic densities of roof support. A wide variety of post-groutable cable bolts are currently in use in the Australian coal mining industry, each of varying capacity, design, and grouting methodology. Though all of the cables are supplied with the appropriate steel specification, strength, and modulus data, the Australian coal mining industry does not have access to a comprehensive and comparative database on the corresponding load transfer performance, which is a critical problem. On the basis of the above, this paper describes the methodology and results of a laboratory pull testing program that aims to assess the impact of cable bolt design on load transfer, and specifically, the impact on the capacity and stiffness of the anchorage. As part of the testing program, 19 cables were tested including (1) plain-strand cables installed in holes drilled with 28 to 55 mm diameter drill bits and (2) bulbed and nutcaged cables installed in holes drilled with 42 to 64 mm diameter drill bits. Other parameters assessed included the significance of smooth and profiled wire, wire packing, and expanded geometry bulbs. The main results of the testing indicate that in comparison to plain-strand cables, if the cable is bulbed or nutcaged, the capacity of the anchor can increase by up to 400%, and the peak stiffness by between one and two orders of magnitude. The results also indicate that increasing hole diameter may have a positive impact on load transfer in the case of bulbed or nutcaged cables and a negative impact on plain-strand cables. No conclusive results were obtained with regard to the impact of grout strength on load transfer.

Jan 1, 2012

By N. P. Kripakov

This paper presents a brief overview of current bump mechanics theories and pillar design methodologies, and relates these concepts to experiences at two mines located in a north-central Utah coalfield where different pillar designs were used to control mountain bumps. Experiences gained at the first mine demonstrated the successful implementation of a two-entry, 9.8 m (32 ft)-wide, yield-pillar design. A U.S. Bureau of Mines field study quantified the timing of chain pillar yielding and resulting load transfer from the gateroad. In-mine pillar response, although apparently sensitive to site-specific conditions, compared favorably to estimates derived using two yield-pillar design methods. A second study conducted at another mine located in the same district, but subjected to different geologic conditions, documents the unsuccessful attempts to employ progressively narrower three-entry pillar designs based on successes achieved at the first mine site. This second mine never achieved a true yield-pillar design. Use of pillar widths ranging between 9.1 m (30 ft) and 27.4 m (90 ft) always resulted in violent bumps in the tailgate pillars. The pillars were either too large to yield, or too small to support peak operational loads. Hypothetical gateroad systems were evaluated using both analytical and empirical approaches for configurations comprised of two rows of conventional pillars, and systems incorporating both yield and abutment pillars. Analysis concluded that yield pillars less than 6.1 m (20 ft) wide and abutment pillars ranging between 30.5 m (100 ft) and 39.6 m (130 ft) square would be required to achieve a stable gateroad design. However, results of a field study conducted on a two-entry, 36.6 m (120 ft)-wide abutment pillar concluded that abutment pressures from the first panel overrode the pillar, and that a still larger pillar may be required to preclude bumps in the tailgate during second panel mining. Without the benefit of a demonstrated in-mine success, it is not clear which design would ensure elimination of gateroad bumps.

Jan 1, 1992