Search Documents

By Chris Haycocks

The relevant literature concerning ground control, mine planning and reserve conservation in multi- seam mining is reviewed. Factors affecting interaction, interaction mechanisms, and design guidelines are presented in detail. The impact of multi-seam mining on future mining, measures for ameliorating negative interaction effects, and future research needs are also discussed.

Jan 1, 1990

By D. W. H. Su

Following a roof fall in the B12 headgate of a CONSOL Pennsylvania Coal Company (CCPC) underground coal mine in February 1998, CONSOL R&D and Exploration initiated an underground roof geology reconnaissance program along the B13 and B14 developments to define potential roof instability areas and to recommend appropriate supplemental headgate support. This reconnaissance program revealed the presence of a thick, massive Pittsburgh sandstone channel overlying the B13 and B14 panels. Surface and underground core holes confirmed the close proximity and the very massive, nonlaminated nature of the sandstone. To mitigate anticipated adverse conditions at the B 13 and B 14 longwall faces due to delayed caving of the massive sandstone behind the shields, a task force consisting of Operations, Exploration, and R&D personnel was formed in May 1998. Several operational adjustments were made by mine management, including repairing damaged lemniscate links, maintaining immediate forward shield support, and implementing measures recommended by the task force intended to boost the shield set load density at the face. After reviewing available geotcchnical information, the task force also recommended fracing of the massive sandstone over the B13 and B14 panels to enhance caving characteristics and further reduce the bending-induced stresses in the sandstone near the face. Horizontal fracs were created at a horizon about 25 feet above the Pittsburgh seam main bench over the two panels in June and November 1998, respectively. To evaluate the effect of sandstone fracing and operational adjustments on the bending-induced stresses in the sandstone, three finite element models were constructed and analyzed. Results from the finite element analyses indicate that one horizontal frac, 25 feet above the Pittsburgh seam, would reduce the bending-induced stresses in the sandstone by approximately 50 percent, maintaining them at a level below the ultimate strength of the sandstone. Operational adjustments to increase the support set load density and support stiffness could reduce the bending-induced stresses in the sandstone by a maximum of an additional 10 percent. Shield pressure monitoring at the B14 midface confirmed the presence of a lower roof pressure zone inby and outby the 1314 frac holes. This lower face pressure significantly contributed to improving the B13 and B14 longwall productivity and safety. The total production downtime due to bad top at the B 12 face within the interval of channel influence was 30,600 minutes compared to about 3,500 minutes each for the B13 and B14 faces. The average longwall advance per machine shift for the B13 and B14 faces within the channel was about 70 percent higher than that for the B 12 face.

Jan 1, 2001

By Keith A. Heasley, Jian Yang

"LaModel uses a laminated overburden boundary-element model and can calculate not only seam-level stresses and displacements but also surface subsidence for thin tabular deposit such as coal seams (Heasley, 1998). Up to this point in time, the material property wizards in LaModel have primarily been designed for calculating accurate stress distributions in single- and multipleseam situations, and for investigating and optimizing pillar sizes and layouts in relation to overburden, abutment, and multipleseam stresses. However, the critical input parameters that will give the most accurate seam-level stress distribution do not necessarily produce the best surface subsidence prediction. The objective of this paper is to develop a methodology for calibrating the critical input parameters in LaModel to optimize surface subsidence prediction.For optimum surface subsidence prediction, it was found that the gob convergence (as defined by the final gob modulus) and the overburden stiffness (as defined by the lamination thickness) were the two most critical parameters that needed to be calibrated (Heasley, 2016). By calibrating numerous panels with various widths and depths, a formula that provides the optimum final gob modulus to use for subsidence prediction was developed. Also, three different empirical formulas for optimizing the lamination thickness as a function of overburden depth and/or the panel width to- depth ratio were determined for the three cases: supercritical panels, and subcritical panels with and without offsets. Further, if the user has measured data for subsidence factor and angle-of draw, the optimum final gob modulus and lamination thickness can be determined from the measured data. These new subsidence prediction formulas are being implemented into new material wizards in LaModel.INTRODUCTIONIn the past few decades, with the increased need for highly productive mining techniques, full extraction mining methods have been increasingly employed in the U.S. coal mining industry. These total extraction mining methods, which include both longwall mining and room-and-pillar retreat mining, normally cause immediate roof caving and the associated surface subsidence. These methods can be highly productive and cost-effective, but the associated surface subsidence can cause damage to surface structures and negatively impact the surface environment (Peng, 2008). Therefore, a reliable program for predicting the surface subsidence associated with full extraction mining is required for appropriately engineering and managing the surface subsidence impacts of full extraction mining."

Jan 1, 2016

By Thomas Barczak

Pumpable roof supports provide an alternative longwall tailgate roof support and have grown in usage during the past few years. Heintzmann Corporation has been installing pumpable roof supports at the RAG Resources Emerald Mine in western PA since 1998, where they have provided effective roof control in their longwall tailgates. Despite the success of these supports in this application, questions remain regarding critical design issues for optimizing the use of this support technology. The support loading profile is characterized by a high initial stiffness with peak loading occurring at less than one inch of convergence, followed by significant load shedding with a post failure capacity comparable to that of wood cribbing. Therefore, the key to optimizing the support utilization is to provide sufficient load density to prevent convergence from occurring beyond the peak loading capacity. This requires an understanding of how the supports interact with the ground conditions, hence measurement of the ground reaction curve. In order to obtain this information, pumpable roof supports were instrumented to measure support loading. Roof deformation and roof-to-floor convergence measurements in the vicinity of the instrumented supports were also made. The experimental parameters for the installation were the support spacing and water¬to-solids ratio of the grout, which controls the grout strength and ultimately the maximum capacity of the support. The study clearly shows that at this mine a 24-inch diameter support is fully capable of providing adequate ground control under depths of cover of 750 ft as only 50 pct of the available support capacity was utilized outby the longwall face. It was also shown that the 2.00 to 1 water¬solids ratio, despite providing a slightly softer support response, is sufficient for maintaining the same degree of roof control provided by the traditional 1.75 to 1 grout mix. The 10-ft spacing of the supports did not cause any ground control problems outby the face. However, inby the face the performance of the support is degraded once the peak capacity of the supports is exceeded. It appears that the large load shedding behavior, which is characteristic of this support following peak loading, allows the immediate roof to separate. When this happens, the support is unable to regain control of the roof in time to prevent failure of the immediate roof beam.

Jan 1, 2003

By Karl Jr. Zipf

The famous Homestake gold mine in Lead, SD. closed recently alter 125 years of operation. However, the mine may receive a new lease on life as a National Underground Science Laboratory (NUSL) supported by the National Science Foundation (NSF) and dedicated to high-energy physics experiments involving neutrinos. These experiments require the construction of many large underground chambers tells of meters wide at depths of over 21 18 m. Construction of such large openings at such extreme depths has few precedents m civil-engineering-type construction. The Spokane Research Laboratory has a long history of ground control research at the Homestake Mine and has supported NSF and the physics community in their efforts to develop a NUSL at I Homestake or other suitable location. This paper will summarize underground science and describe proposed underground science laboratories ill the United States, in particular tile proposed NUSL at Homestake. Next, the paper describes an empirical design approach using the Q system of rock mass classification for these large Openings. .M initial site investigation that produced three good case histories is described. The actual support system used at the three sites agrees well with support recommendations from current support design charts, giving credibility to estimates of the classification parameters and Q. Feasibility of, and support requirements for, 25-, 50-, and 100-m spans arc estimated in the anticipated rock mass. This analysis indicates that 25- and 50-m spans are probably feasible, but a stable 100-nn span may be unachievable. The empirical predictions are then compared to detailed numerical analyses. The paper concludes with preliminary support recommendations and necessary site investigations needed to make a proposed NUSL a successful reality. These studies have been important input to NSF for their decisions on the technical feasibility of developing the proposed NUSL. If NUSL is developed, it could enable scientific experiments in areas beyond high-energy physics. 'the laboratory could also enable research in rock mechanics. ground water hydrology. mining engineering, nine safety and health, and ground control.

Jan 1, 2002

By R. Karl Zipf

Multiple seam mining interactions caused by full extraction mining, whether due to undermining or overmining, frequently involve tensile failure of the affected mine roof. The adverse ground control conditions may prevent mining for both safety and economic reasons. Prior researchers have identified the geometric, geologic and mining factors controlling multiple seam mining interactions. This numerical study examines the mechanics of these interactions using a modeling procedure that 1) incorporates the essential constitutive behavior of the rock such as strain- softening of the intact rock and shear and tensile failure along bedding planes and 2) captures the geologic variability of the rock especially the layering of weak and strong rocks and weak bedding planes. Specifically, the numerical study considered the effect of vertical stress, interburden thickness, and the immediate roof quality of the affected seam in both undermining and overmining situations. The models show that for overburden-to-interburden thickness (OBAB) ratios of less than 5, interactions do not occur, and that for OBAB more than 50, extreme interaction is a certainty. In between, the possibility of an interaction was found to depend on gob width-to-interburden thickness ratio, site specific geology and horizontal stress to rock strength ratio in addition to the OBIIB ratio. The models also showed that horizontal stress was profoundly altered well above or below a full extraction area and that these changes are likely to influence the success or failure of multiple seam mining. The role of horizontal stress in multiple seam mining interactions has received little attention in prior investigations. Four factors control the mechanics of multiple seam mining interactions: 1. vertical stress concentration 2. horizontal stress concentration 3. stress re-direction 4. bedding plane slip bands A combination of vertical and horizontal stress increase and high stress gradients in the vicinity of full extraction areas re-orients principal stresses into a very unfavorable direction. This seemingly small stress re-orientation has a profound adverse effect on bedded rock.

Jan 1, 2005

By Dakota D. Faulkner

Cable bolts have been very effective in mine ground control. Non-tensioned and tensioned cable bolts are now used for both primary and supplemental bolting (Suder, 2001; Mirabile, 2010). In the United States, cable bolts are typically installed in either 1 or 1-3/8 in. (25 or 35 mm) diameter drill holes and, if point anchored only, are utilized with 4 - 5 equivalent feet (1.2 - 1.5 m) of resin. Cable bolts can be tensioned by various methods such as using an expansion shell mounted on the cable or post-tensioned with a hydraulic cable tensioning unit. In recent years there has been a desire to completely encapsulate the cable bolt for corrosion protection. Fully encapsulating a cable bolt with traditional resins can be very difficult. Keystone Mining Services, LLC (KMS) and Jennmar Corporation have developed a new cable bolt that can be fully encapsulated during installation or post-installation with polyurethane (PUR). The Fully-Grouted Cable Bolt (FGCB)* is equipped with a special head that allows the injection of PUR up through the cable bolt head and cable strands, completely encapsulating the cable and filling the drill hole. Although the FGCB was initially developed to fully encapsulate the cable for corrosion protection, it was also found that by modifying the cable bolt head and injection pressure, PUR could be injected into cracks and fissures of the strata to stabilize the roof. This paper details the development of this system and three underground applications under different ground conditions.

Jan 1, 2012

By Anthony Iannacchione

As the amount of new fractured surfaces or "damaged rock layers" within roof rock increases, the stability of the rock mass decreases. While direct measurements of this phenomenon are not easily made, there is good circumstantial evidence to support this hypothesis. For example, it is common to observe increased cracks or fractures in the immediate mine roof rock before a roof fall. Likewise, roof drill holes placed in areas that later fail often reveal increased numbers and/or separations of fractures within the rock column through time. And finally, the frequency of microseismic activity, representative of rock fracturing, increases before a roof fall. For this study, more than 700 microseismic emissions were collected from two underground limestone mine roof fall areas in southwestern Pennsylvania. Microseismic events were located and magnitudes determined using the moment magnitude technique. Moment magnitude is based on the event seismic moment, which is a measure of the seismic deformation. The amount of new fracture surface length was calculated based on the stored strain energy within the rock prior to fracture. In the two case studies presented, a significant amount of microseismic activity was observed as much as two days before the first signs of failure in the roof fall areas. Additionally, results from this analysis reveal much about the behavior of strata prone to failure and allows for the construction of hazard maps based on microseismic emissions. The potential use of this technique as a means of anticipating roof falls is analyzed and discussed.

Jan 1, 2004

By Dennis R. Dolinar

A room and pillar coal operation in central Pennsylvania was experiencing roof cutters and long running roof falls caused by high horizontal stresses. The roof conditions created hazards for the miners, and caused several production panels to he abandoned prematurely. The mine requested assistance from the National Institute for Occupational Safety and Health (NIOSH) in applying the "advance and relieve" mining to reduce the affects of the horizontal stress during panel development. The "advance and relieve" plan that was developed called for removing a pillar on one side of the panel as it was being advanced, thus creating a cave. The caving then relieved a portion of the horizontal stress across the panel. Because the horizontal stress direction is key to the success of this method, stress mapping as well as mining experience was used to establish the direction of the horizontal stress. Subsequent field measurements provided an estimate of the stress magnitude. Three panels were mined using this technique, and good roof conditions were achieved in all these panels. Instrumentation was used to monitor the stress changes in the roof created by the cave. Stress relief of over 1.000 psi was measured 120 ft from the cave and to depths of 20 ft into the roof. The lateral extent of the stress relief zone across the panels appears to be about 400 to 500 ft. This case history has provided much insight into the practical application of the "advance and relieve" method discussed in this paper.

Jan 1, 2000

By Kot Unrug

The selection of tensioned versus non-tensioned roof bolts, for primary coal mine roof support, has been debated for well over 25 years. The wide spread use of fully grouted rebar marked the beginning of the discussion of the relative importance of bolt tension and the resultant immediate roof compression. The focus is on roof conditions encountered in coal mines however the discussion may be extended to hard rock mines as well. The theoretical bases for both systems are presented, with the analysis focused on the bolt's ability to actually fulfill the theoretical assumptions. Of specific concern are assumptions about bolt tension upon installation and the likelihood of maintaining useful bolt tension over time. The usefulness of tension roof bolting is limited by the mechanical interaction of roof bolt assembly and the rock, which may be valid at the time of installation only. Ambient mine atmosphere and fluctuation in moisture content changes the physical condition of rock, which may have a significant impact on the effectiveness and longevity of bolt tension. Changes in the material properties of the surface of the immediate roof can invalidate the assumptions, which were made in the design stage of roof support system. This means that the roof support in the long term excavations may be inadequate requiring costly rehabilitation. The presented arguments are illustrated with the examples of some relevant experimental data. Tension primary roof bolting is recommended where the immediate roof is: ? Stiff with a high modulus of elasticity ? Surface layers are continuous and fairly thin ? Not easily weathered

Jan 1, 2004

By André C. Zingano

The domino effect in a violent pillar collapse occurs due to the redistribution of stress in the remaining pillars near the collapse, and this stress transfer occurs in the immediate and main roofs. The remaining pillars do not have enough load capacity to support this overstress and also fail, and the domino effect propagates further to the entire panel. The domino effect does not occur only due to low load capacity of the pillars, but also the roof rock mass quality, because the stress is transferred by the roof. In high competent roof without discontinuity (fault), like massive sandstone seam, the deformation of the roof is the cause of pillar collapse extension and propagation. Depending on how close it is approaching the collapse limit; the immediate and main roofs behave differently. When it is close to the collapse limit roof convergence and pillars compression occur. Conversely when it is far from the collapse limit divergence and pillars decompression occur. This is called the arc-effect. This paper studies this behavior of the roof (immediate and main roofs) using numerical modeling to simulate the roof deformation and stress distribution in the roof and pillars. This simulation represents the progression of pillar collapse and shows the zone of convergence and divergence of the roof, and also the effect of this behavior on pillar confinement. Two-dimensional plain strain model was applied to simulate the arc-effect. The simulation results were compared to those of the instrumentation that was installed before the collapse. Keywords: pillar collapse, room and pillar, numerical modeling

Jan 1, 2005

By P. E. Christensen

Due to ever-increasing stripping ratios associated with the No. 8 Seam at the San Juan Mine surface operation, BHP Minerals decided to implement longwall mining for the extraction of the substantial future reserve base. In preparation for longwall developments, BHP opted to first develop a small-scale pilot operation within the No.8 Seam on an adjacent lease to address geotechnical/geological concerns related to ground control, subsidence, caving, panel and entry design, and operational issues related to entry development and proper face equipment selection. Room-and-pillar mining methods are currently being utilized to develop a full extraction panel for a wide range of geological, geotechnical, and geomechanical evaluations aimed at characterizing and assessing the mineability of the No.8 Seam. Variable roof and floor conditions, coupled with a multi-bench coal seam, require that a number of mining horizons, opening geometries, and roof and rib support fixtures be evaluated relative to expediting gate and panel developments. Issues related to development of timely caves in areas subject to overlying sand channel deposits will also be addressed through underground in-seam stress and deformation measurements, and interburden and surface subsidence monitoring. This information will ultimately be used to evaluate face support and gate and panel pillar/entry development requirements. The current depositional model for the property, developed from an aggressive drilling, highwall mapping, and lineament evaluation program, will also be refined during the Pilot Mine study through extensive in-trine mapping, additional roof and floor drilling and physical property testing, and determination of the in situ principal horizontal stress field.

Jan 1, 1998

By Styles P.

To determine whether 130 felt earth tremors around Edwinstowe, Nottinghamshire U.K, which also experienced severe surface fissuring, were caused by coal extraction, a surface seismometer array was established around Thoresby Colliery. Over the next year, 785 microseismic events were detected. The spatio-temporal seismicity patterns are clearly associated with the commencement, continuing extraction and closure of faces. Of particular note are events which locate at the surface and appear to be related to the active fissuring. Events occur within days of commencement of production and cease when production finishes, with good correlation between face advance and hypocentral position. Naturally occurring microseismic events have also been detected up to 1 km ahead of active longwall faces in the Midlands using triaxial geophone packages grouted into the seam together with a surface seismometer in the top of the borehole. The quality of these data were very high and guided waves can clearly be seen with the dispersive characteristics associated with seam waves. In one experiment more than 2000 events were detected in only two days of monitoring even in a relatively noisy surface environment. This paper demonstrates how very accurate locations ( 5 10 metres) can be generated using three-component digital data from only one borehole. The surface seismometer and the borehole P-wave onset can give extra precision for the height of the event relative to the seam. The event distributions give a dynamic, three-dimensional image of the developing patterns of fracturing above, below and ahead of the longwall face with important implications for roof control, subsidence prediction and gas migration.

Jan 1, 1992

By Jeff Whyatt

Deformation of underground salt, trona and potash mines is generally time dependent, providing for gradual adjustment of strata to mining induced stresses. Time dependence can allow for higher extraction ratios provided eventual failure can be tolerated. However, this eventual failure can be violent if creep deformation can shift stress and potential energy to strong, brittle geologic units. The mine failure case studies reviewed here illustrate this process. Yield pillars and defects in bridging strata figure prominently in these cases. Yield pillars provide local and temporary support to the roof, temporarily delaying the cave; and allowing extraction ratios and overburden spans to increase beyond the long term capacity of overlying strata. Defects (faults, voids, thinning) of strong overburden strata reduce the critical span, sometimes to less than panel width. Analyses of many of these cases have focused on a cascading pillar failure mechanism, but recent work and this review point to failure of strong overburden strata as the essential element. The suddenness of failure and attendant seismic events pose hazards to miners and, in some cases, to those on the surface. Characterizing these failures is a first step towards recognizing and managing the risk of catastrophic collapse in underground mines.

Jan 1, 2008

By S. Y. Liu

Based on the underground measurements, physical model test of simulated materials in the laboratory and finite element analysis, this paper demonstrates the pattern and process of roof fall over the tip-to-face area in the fully mechanized coalfaces. The main factors that affect the stability of the immediate roof are thoroughly studied including the fracture position and tilt angle of the main roof, the tensile strength (Rt) and cohesive force (c) of the immediate roof, and type and resistance of the powered support. Based on these factors, this paper proposes the basic process of immediate roof breakage a. follows: As the longwall farm advances, the main roof breaks and then rotates. A tensile fracture zone will be formed in the immediate roof under the fracture line of the main roof. A caving zone (plastic zone) will be formed in unsupported area between coalface and canopy tip. If these two zones overlap the immediate roof will be completely unstable. Under this condition, powered support will have difficulties lo control the rod. Therefore it is necessary to study the process of immediate roof breakage and look for effective methods for controlling the roof.

Jan 1, 1990

By Cosmo P. Fazio

Remote control roof bolting is approaching reality with the continued improvement of a number of components and subsystems being developed by The Bendix Corporation under sponsorship of the U.S. Bureau of Mines and the U.S. Department of Energy. The era of remote control research in roof bolting was initiated by the USBM in June of 1973 with the award of a contract to Bendix Corporation to design and build a roof bolt bender/inserter device. One year later in June of 1974, the Bureau awarded five parallel R&D contracts to develop a longer-than-seam-height flexible roof drill. The Bendix flexible drill design has been the most successful of the five, has been thoroughly tested in both laboratory and underground situations, and has been incorporated into a number of machine applications along with the roof bolt inserter. The purpose of this paper is to discuss the advantages of remote control bolting from both a safety and productivity standpoint. Applications of the flexible drill and roof bolt inserter on a number of government and industry supported programs are used to illustrate the advances being made toward the goal of remote control.

Jan 1, 1982

By D. W. H. Su

This paper describes geomechanical criteria employed by Consol Energy for selecting mine-specific longwall face supports in the past decade. The criteria include immediate and main roof rock characteristics, floor rock characteristics, critical tip-to-face distance and shield operating range. Detailed roof rock properties from high-density core holes as well as in-mine scope holes are used to evaluate the set load density and shield stiffness required to control the immediate roof and the yield load density required to absorb the load density developed from main roof weighting. Detailed floor rock properties from core holes and in-mine floor bearing capacity tests are used to specify the maximum peak toe pressure as calculated by the Jackson method. The critical tip-to-face distance is evaluated based on the immediate roof rock strength, layering and thickness. The shield operating range is evaluated based on main bench thickness, the presence of thick draw slate, the potential of minor roof falls at the face and transportation restriction. Three case examples representing three different geologic conditions are presented to illustrate the successful application of these geomechanical criteria for selecting longwall face supports within Consol Energy in the past decade.

Jan 1, 2004

By P. Tsang

In order to deal with ground control problems such as roof falls, floor heaves and pillar failures in underground coal mines, a new pillar design method based on the "yield pillar" concept is proposed. Using the finite element model simulation, the functions and mechanisms of the "yield pillar" are studied. The important variables that affect the stability of longwall entry-pillar system are identified. To simplify the geological and mining conditions, a new pillar design method classifies the in-situ roof and floor conditions into four categories: 1) strong roof and strong floor, 2) strong roof and weak floor, 3) weak roof and strong floor, and 4) weak roof and weak floor conditions. The design formulae are derived based on the finite element model simulation, stability study and nonlinear regression analysis. The finite element models used consider the plastic failure properties and time-dependent behaviors of rock. To better organize the finite element model simulation, the orthogonal experiment design is used to arrange the finite element models and proved to be very effective. An application example is used to illustrate the basic design procedures involved in the new pillar design method.

Jan 1, 1993

By James M. Tennant

In the mid 1970's, American Electric Power significantly expanded its internal coal production. This involved opening several large mines in seams that had never been mined on a large commercial scale before. One of the mines opened was the Martinka No. 1 Mine which is located approximately five miles southeast of Fairmont. The mine was originally designed for room and pillar mining with continuous miners but was later modified to permit the utilization of longwalls and continuous miners for entry development. The coal seam to be mined was the Lower Kittanning which averages fifty-six inches. In order to successfully mine this seam, it required that the mine design recognize the effect caused by the dip of the seam which averages four percent to the Northwest with a maximum of sixteen percent for short distances and a relatively low cover. In fact, seventy-four percent of the reserves have cover of less than four hundred feet. Also, the core hole data indicated that the immediate roof varied from zero to eighteen feet of shale with two to forty-five feet of sandstone overlying the shale.

Jan 1, 1982

By H. Gene Wilson

Mobile Roof Supports (MRS) look similar to a longwall shield on crawler tracks. The MRS units offer a safe, productive method of extracting the 40% to 60% product left normally unrecovered in room and pillar mining. The units feature radio control, self-contained power units, crawler track drive, and a 600 ton yield. Cribbing and setting posts in retreat mining has been a necessary burden to production. The MRS reduces this burden. Long blocks of coal can be developed to further reduce move and tram time, thus increasing production. The MRS units have successful safety records. The workers are removed from the immediate fall area, and we feel back injuries have been reduced by the workers not setting posts. While MRS units have been damaged in falls, the other capital equipment has been unharmed. The MRS product line has undergone normal product improvement and evolution. Product evolution is seen in our development of machines for particular mine requirements. Through the continuing development of the MRS, Fletcher presents the coal industry with a safe, productive method of retreat mining with potential to develop new mining methods.

Jan 1, 1990