Search Documents

By P. Trueman

A project is underway to convert a validated methodology to a system that will permit the near real time interpretation of loading data from longwall powered supports, allowing rapid adaptation of mining strategies, maintenance scheduling and set pressures for optimal roof control. Such a system has the potential to significantly reduce roof control problems and is a pre-requisite to successfully fully automating a longwall face. The development depended upon a robust methodology for interpreting the pressure sensor data coming from the face in the context of support strata interaction using a novel characteristic load cycle analysis concept. New software was developed capable of handling the large quantity of data emanating from a modern longwall with the current level of signal corruption and loss, accurately delineating load cycles and extracting the critical load cycle features essential for interpreting how the support and strata are interacting. Existing software being used to access the pressure data were found either to be incapable of delineating load cycles at all or, where they could, the accuracy was low, making it impractical to use them in combination with the new advances in load cycle analysis. The software is currently being extended from ?off line? to ?on line? in order to provide a real time response to changing strata conditions.

Jan 1, 2006

By Doug Tesarik

Researchers from the National Institute for Occupational Safety and Health1 (NIOSH), together with employees from The Doe Run Company, are monitoring and evaluating the stability of a pillar retreat section at the Fletcher Mine, a lead/zinc, room-and-pillar mine near Bunker, MO. Cemented rockfill is being used to provide roof support as high-grade, remnant ore pillars are mined. Earth pressure cells and deformation meters placed in backfill panel pillars monitor stress change and vertical deformation, respectively, as nearby ore-bearing pillars are extracted. Similarly, biaxial stressmeters and borehole extensometers are used to monitor mining-induced stress change and deformation, respectively, in long-term support pillars. Data from these instruments indicate that when ore-bearing pillars were mined, stress was redistributed from support pillars to a backfill panel pillar. The data also indicate that the backfill and support pillars have remained stable for two years after pillar extraction was completed in the area. This research demonstrates the importance of using reliable instruments to document the geomechanical behavior of pillars and backfill. Gaining a better understanding of roof support and stress redistribution mechanisms is a fundamental part of NIOSH's goal to reduce and/or predict rockfalls, which are still among the leading causes of injuries in metal/nonmetal underground mines.

Jan 1, 2006

By William Gray

It has been ten years since the Mine Safety and Health Administration (MSHA) promulgated a safety standard requiring the use of Automated Temporary Roof Support (ATRS) systems in underground coal mines. The use of ATRS systems with roof bolting machines and continuous miners equipped with integral bolters has all but eliminated fatal roof fall accidents associated with manually setting temporary roof support. The last ten years have seen an evolution of the ATRS systems themselves and of MSHA's policy regarding ATRS systems. These changes are a response to operational and safety issues regarding ATRS systems often brought about by the ever-changing coal mining environment. As a result, MSHA's Technical Support personnel receive numerous inquiries from all segments of the coal mining industry on various ATRS topics. These requests for technical assistance range from an interpretation of a facet of the ATRS standard to an in-depth evaluation of a prototype ATRS system. This paper will address the aforementioned evolution of ATRS systems and will also summarize the factors MSHA Technical Support uses to evaluate these systems in the field. In addition, some of the more common misconceptions regarding the design, use, and regulatory requirements regarding ATRS systems will be covered.

Jan 1, 1998

By Keith Heasley

As part of the initial investigation and validation of a new boundary-clement formulation for stress modeling in coal mines. the underground stresses and displacements at two multiple-seam coal mines with unique stress problems are modeled and predicted. The new program, LAMODEL, calculates stresses and displacements at the seam level and at requested locations in the overburden or at the surface. Both linear elastic and non-linear seam materials can he used: and surface effects, multiple seams, and multiple mining steps can be simulated. In order to most efficiently use LAMODEL for accurate stress prediction, the program is first calibrated to the site-specific geo-mechanics based on previously observed stress conditions at the mine. For this calibration process. a previously mined area is "stress mapped" by quantifying the observed pillar and strata behavior using a numerical rating system. Then, the site-specific mechanical properties in the model are adjusted to provide the best correlation between the predicted stresses and the observed underground stress rating. Once calibrated, the model is then used to predict future stress problems abead of mining. At the two case study mines, the calibrated models showed good correlation with the observed stresses, and also accurately predicted upcoming high stress areas for preventive action by the mines.

Jan 1, 1998

By Thomas M. Barczak

The performance characteristics of Mobile Roof Supports (MRS's) were evaluated through full-scale testing in the Strategic Structures Testing Laboratory at the National Institute for Occupational Safety and Health, Pittsburgh Research Center. Safety issues pertaining to the operation and design of these supports for pillar extraction during retreat mining are examined. A unique load frame, called the mine roof simulator, provided a realistic simulation of mining conditions by inducing vertical, horizontal, and lateral loading on the support. The purpose of these experiments was to determine the capabilities and limitations of the supports and to investigate factors that influence the measurement of loading and loading rate. An evaluation of the support design and load conditions that can cause support failure or loss of support capacity are discussed relative to the laboratory tests. In general, lateral loading perpendicular to the longitudinal axis of the canopy is most severe, although horizontal loading in the direction of the long axis of the canopy can also produce critical loading in some cases. The experiments indicate that both setting force and leg pressure measurements are influenced by the staging of the leg cylinders. The implications of these factors on load rate measurement are evaluated. A comparison of MRS capacity and stiffness characteristics is made to conventional timber supports.

Jan 1, 1997

By Thomas Barczak

A cooperative study was conducted with Emerald Coal Resources, L.P., an affiliate of Foundation Coal Corporation, and the National Institute for Occupational Safety and Health (NIOSH) to evaluate the effectiveness of (partially) pre-driven longwall recovery rooms supported with pumpable roof supports. This paper evaluates the load transfer mechanics associated with the advancement of the longwall face into the pre-driven recovery room and the widening of the room to recover the longwall shields. The results show that the yielding of the panel fender produced uncontrollable convergence that caused yielding of the shields and stiff pumpable roof supports when the face was approximately 10 ft from the recovery room. The shields continued to yield until the face advanced into the recovery room. Convergence in the pre-driven recovery room typically reached 6-8 in once the pumpable supports yielded and shed load through a declining residual load capacity prior to being cut out by the longwall shearer. Roof deformations occurred beyond the 32-ft horizon with total deformation ranging from 2 to 4 in, indicating that standing support was necessary to help control the span as the longwall face advanced into the pre-driven recovery room. Stability improved as the pumpable supports were cut out, thereby reducing the span between the shields and the outby pillars. In the end, the shields were successfully recovered under stable ground conditions. However, a disconcerting discovery was the load shedding of the outby pillars as the recovery room was mined into. It is postulated that this may be due to the progression of the rear ?abutment? moving toward the recovery room as the panel fender and standing support in the recovery room yield and shed load. This behavior was not expected with a relatively narrow room that is fully supported with standing support. If this mechanism is indeed occurring, the width of the room and performance of the standing support becomes even more critical. Premature failure of the support can lead to excessive convergence on the shield line that cannot be controlled even with modern shields, resulting in roof instabilities that can lead to catastrophic results.

Jan 1, 2007

By Luis Giraldo

Rock bolt installation characteristics near roof falls have been identified as contributing to failure. One documented and regularly occurring failure mechanism is loss of anchorage between the grout and the rock wall of the bolt hole. Key contributors to the integrity of the grout interlocking with the rock mass are the diameter of the hole relative to the diameter of the bolt, resin versus cement type grouts, rock type, and condition of the hole. Smooth bolt holes consistently exhibit less rock bolt load bearing capacity than rough walled holes. The goal of this study was to quantify the benefits of borehole conditioning and develop a systematic approach that would allow improvement of roof bolt performance. A new rock drilling technology, the Helical Drag Bit (HDB), was used in the early stages of this project to condition the borehole. The HDB cuts a prescribed helical groove in the borehole wall. When a bolt is grouted into a hole that has been conditioned using the HDB, the grout fills the helical groove and provides a stronger, more reliable mechanical lock between the rock and the grout. This paper presents results of a series of tests conducted in the laboratory and in the field. Short encapsulation pull out tests have demonstrated considerable increase in pull out strength and more consistent bolt performance when hole geometry is modified using the HDB. The results have also shown that greater load bearing capacity improvements are obtained in mines with weak roof rock, where it is most needed. Additionally, bolts recovered for examination suggest that hole conditioning during roof bolting reduces the effects of finger gloving. Therefore, mines with stronger roof rock could also benefit from hole conditioning. A new roof bolt that uses the HDB principle has been designed and tested. The new system works with existing bolting equipment requiring minimal modifications to the traditional procedure used for installation of fully grouted rebar bolts. The use of these higher anchorage capacity bolts will allow mines to reduce severe injuries and fatalities resulting from ground failures while maintaining or increasing productivity.

Jan 1, 2005

By D. Newman

The objective of this is paper is to review the current state of knowledge and practice in highwall mining (HWM). HWM has become a standard method in surface mining, commonly used alone or in conjunction with contour or slot mining. It provides 800-feet to 1,200-feet of additional recovery when the economic stripping ratio is reached in contour mining or in slot mining when surface access to a reserve is limited. A significant attribute of the highwall miner is its versatility. HWM has been used successfully to mine abandoned pre-reclamation law highwalls, points or ridges uneconomic to mine by underground or other surface methods, outcrop barriers left adjacent to underground mines, separate benches of the same seam where the parting thickness or quality differences between benches render complete extraction uneconomic, previously augered areas containing otherwise inaccessible additional reserves and close or widely spaced multiple seams. The theory and design methods to assess roof; pillar, and floor stability are presented followed by three case histories. Simple design charts for sizing HWM web and barrier pillars are also presented. A recommended web pillar width may be obtained from the design charts given the overburden depth, the HWM cut width, and the mining height. Given the depth and panel width for a set of HWM cuts, another set of charts gives a suggested barrier pillar width. The case histories, hm Northern and Southern Appalachia are used to illustrate the application of rock mechanics to quantify the stability of the highwall, roof, web pillars, and floor. The case histories involve 1) mining through a previously augered highwall, 2) mining under back-stacked spoil and 3) selective mining of closely spaced benches of the same seam. Because each site is unique, the appropriate pre-mining geotechnical analyses range from the calculation of roof, web pillar, and floor bearing capacity stability factors to detailed numerical modeling of the auger and underground mine workings. When operating in the vicinity of existing underground mine or auger workings, the determination of ground deformation and strains resulting from highwall mining is a necessary facet of a ground control investigation.

Jan 1, 2005

A model was developed to facilitate secondary tailgate support selection based on analysis of over 100 case studies, compiled from two different surveys of operating longwall coal mines in the United States. The ALPS (Analysis of Longwall Pillar Stability) program was used to determine adequacy of pillar design for the successful longwall case histories. A relationship was developed between the secondary support density necessary to maintain a stable tailgate entry during mining and the CMRR (Coal Mine Roof Rating). This relationship defines the lower bound of secondary support density currently used in longwall mines. The model used only successful tailgate case history data, with adequate ALPS SF according to the CMRR for each case. This model facilitates mine design by predicting secondary support density required for a tailgate entry depending on the ALPS SF and CMRR, which can result in significant economic benefits.

Jan 1, 1996

By Hani Mitri

A new monitoring device called SAFEBOLT (Stress And Force Evaluator in Bolts) has been recently developed. The device SAFEBOLT, essentially replaces the load cell, it permits the monitoring of bolt axial load from the time of its installation underground. The SAFEBOLT system consists of a portable readout unit, connecting cable and the SAFEBOLT device, which is installed in the bolt head. SAFEBOLT can be installed on any industry standard rockbolt. No special installation method is required; the conventional method of bolt installation by the stoper or roofbolter remains unchanged. The device is completely encapsulated in the bolt head, which makes it resistant to corrosion, rugged, and free of any electrical wires. Pilot tests at three underground Quebec mines were carried out and helped improve the initial design of the device connector. The paper reports on two of such pilot tests.

Jan 1, 2001

By Bruce W. King, David A. Newman

"Underground mines have always been an integral part of the limestone industry. However, beginning in the 1990s, the number of underground limestone mines has increased for many reasons including• Stripping ratios at surface quarries have become uneconomic.• Existing surface quarries have reached the mineral boundaries, and the remaining stone reserves are underground.• Surface access to the entirety of the limestone reserve is limited by development or infrastructure.• The once-rural setting of the surface quarry is now surrounded by subdivisions and development. An underground mine is less intrusive and takes the mining operation out of the public eye.• For larger markets, an underground mine enables year-round production without the sequence of overburden stripping in the winter to expose mineable stone for summer production. This is common at many surface quarries.Multiple-level operations are a natural extension of the decision to mine underground. Most limestone reserves, for example, the Tyrone-Oregon-Camp Nelson, Hermitage-CartersLebanon- Ridley, and Salem Limestones, are sufficiently thick to accommodate multiple levels. Multiple-level mines should be planned by considering each level separately and then integrating the individual levels into a larger mine plan. Failure to plan all the levels of a multiple-level mine in concert can result in ground control (back, pillar, floor, and inter-level sill pillar) problems attributable to stress transfer and interaction between the levels or the necessity to leave a thicker sill pillar between adjacent levels.Multiple-level mine planning begins with geology. Once the upper level back horizon is identified, the geology, rock strength, and physical properties in each level are used to• identify the optimal back horizon• quantify whether back support is required and, if so, the type, spacing, and length of the back support• determine the pillar centers• determine the total mining height, including floor shots"

Jan 1, 2016

By S. Paul Singh

The implications of blast damage are harmful in both economic and physical sense. To understand the mysterious nature of blast damage assessment and prediction, field work was done by driving an experimental tunnel in the bench of a quartzite quarry. On the basis of the blast vibration monitoring records, a model was developed to predict the PPV at different distances from a blasthole. Critical particle velocity for damage and the output of the prediction model were used to delineate the extent of damage for different explosives. The predictory model was tested by designing a special blast and the burdens for the back holes have been recommended. The relationship between the critical particle velocity for "Fall Off' and the critical particle velocity for damage has been established. The existing criteria for blast damage have also been renewed in this paper.

Jan 1, 1993

By Thomas Barczak

Longwall shields provide essential ground control in Iongwall mining, yet a high percentage of shields are operating at less than peak capacity and many at well below the rated support capacity due to defective hydraulic cylinders or malfunctions in other hydraulic components. Leg pressure data are currently collected on state-of¬the-art longwall shields, but typically are not analyzed to evaluate shield performance. The National Institute for Occupational Safety and Health (NIOSH) Shield Hydraulics Inspection and Evaluation of Leg Data (SHIELD) program is a Visual Basic software system that is designed to analyze leg pressure data and identify shields that are not performing to rated specifications. The program analysis is configured to detect the following conditions: (I ) loss of leg pressure, (2) imbalance in leg pressure, (3) low set pressure, (4) low yield pressure, and (5) full extension of the bottom stage. Other performance assessment measures include the percentage of the support capacity utilized (ratio of peak load to yield load), the percent of time that a shield operates at yield load, the ratio of the set load to the yield load, and the amount of support capacity that is lost due to leaking cylinders. Historical record keeping will allow the user to select a particular shield and review the performance record as developed by the program for that shield. In addition to these performance assessment measures, the software will include an animated description of shield hydraulic systems that will describe the operation and significance of each hydraulic component and the impact of component failures on the shield's capability to provide the required roof support. A general overview of the SHIELD program is provided in the paper together with an example analysis of a 2.5-year-old Australian longwall face.

Jan 1, 2002

By Andrew Starkey

Ground anchorage systems in the form of rock bolts are used extensively throughout the world as supporting devices for civil engineering structures such as bridges and tunnels. It is widely recognized that non-destructive testing methods for ground anchorages need to be developed as a high priority [1 ], with only a small proportion of anchorages currently being monitored in service [2]. The condition monitoring of anchorages is a relatively new area of research, with the objective being a wholly automated or semi-automated condition monitoring system capable of repeatable and accurate diagnosis of faults and anchorage post tension levels. The GRANIT tm system developed by the University of Aberdeen is capable of measuring the integrity of ground anchorages and has won two major UK Awards - the National John Logic Baird Award for Innovation in 1997 and a Design Council Millennium Product Award in 1999. The normal procedure with the GRANIT tm system [3,4] is to train a neural network on dynamic response data that has been sampled from an anchorage over a range of post-tension levels. Further data is needed in order to test the neural network. The paper presents neural networks that have been trained on data taken from a number of anchorages on different sites, and the results of the diagnosis of these neural networks on new test data is presented. The results show that the cross-diagnosis of anchorages is possible, where a neural network trained on one anchorage is capable of successfully diagnosing the post-tension level for an anchorage of similar construction, and the high level of accuracy that can be attained with the GRANIT tm technique is shown. The paper also introduces a mathematical model of the GRANIT tm process.

Jan 1, 2001

By Thomas M. Barczak

A survey of the longwall industry was conducted to examine the performance of modern shield technology. The results of this survey indicate that state-of-the-art shields perform better and last longer than ever before, but premature failures do still occur. In addition, longwalI operators are now using shields longer than ever before and a greater number of fatigue related failures on aging shields are now occurring. A generic assessment of these shield failures is provided, describing the nature of the failures and how widespread they are throughout the industry. An engineering assessment of shield design and factors that cause shield failures is made using both strength of materials and fracture mechanics principles. From this analysis, design practices to improve structural margins of safety and extend the life of the shield are proposed. The existence of unexpected shield failures indicate that current shield performance testing is at times inadequate. Recommendations are made relative to improved shield performance testing protocols including the benefits of testing in an active load frame such as the National Institute for Occupational Safety and Health's (NIOSH) Mine Roof Simulator. Even the most rigorous shield testing procedures, which strive to simulate in-service loading conditions, fail to consider key environmental issues, such as corrosion which is often the cause of structural fatigue failures in modern shields. The survey also indicated that hydraulic failures occur much sooner in the life cycle of a shield than structural failures, and although they can significantly degrade support capability, often go undetected for long periods of time. Methods to detect the hydraulic failures are also provided. The paper concludes with key points to maximizing shield design and life expectancy and ideas for future generation shield designs.

Jan 1, 1999

By Jay Hilary Kelley

This paper proposes a modification of longwall roof support to meet new difficult mining conditions that are anticipated in the future. A gob canopy is a movable appendage attached on the rear of a longwall shield to counterbalance the troublesome forward downward force couple (FDFC). The gob canopy can be swung in both vertical and horizontal directions, powered by hydraulic cylinders. Several functions and applications are de- scribed

Jan 1, 1997

By Robert C. Garson

The Mine Roof Simulator at the DOE'S Mining Equipment Test Facility is described. Its use in the research and development on the behavior and response of longwall roof supports to simulated mine environment is investigated. Advanced technology analysis methods such as finite element modeling, strain gage instrumentation, and photoelastic techniques are investigated for application in roof support design two case studies are presented of test data and results.

Jan 1, 1982

By Axel Studeny

Geomechanical-numerical methods are an established tool for planning of underground excavations worldwide. By describing the interaction between heterogeneous layered strata and support elements it is possible to determine their suitability. The German hard coal mining industry has more than twenty years experience in investigation and using these parameters to carry out numerical calculations. Today, nearly all excavations (shafts, pit bottoms areas, bunkers, coal faces, development drivages, gate roads etc.) are calculated by geomechanical-numerical tools in combination with empirical planning methods. A high accuracy of planning results, which is a special requirement in the German coal industry with its deep-level longwalls, bedded and weak surrounding strata and multiple seam mining layouts, depends on the extensive calibration of the numerical models, which is achieved by: 1) Taking a large number of underground measurements with empirical evaluation. 2) Carrying out physical modeling. 3) Using the characteristic features of the installed support elements. This paper compares the planning approach used for multiple and single seam mining and presents the advantages of this planning tool. The main focus is on the feasibility of rockbolting as the sole means of roadway support for multiple seam mining operations, though the paper will also look at how the costs can be improved by using a low bolting density in single seam layouts.

Jan 1, 2007

By André Zingano

Pillar collapses have been studied for several years and can be classified into two types: nonviolent squeeze or violent pillar collapse, i.e., controlled or uncontrolled pillar collapse. Underground coal mines in Brazil are considered shallow mines, because the overburden thickness varies between 20 and 400 meters. For this reason, the coal pillars should be designed as permanent pillars to avoid subsidence and groundwater problems. In the last two years, various pillar collapses occurred, one being a violent collapse and the others being squeeze collapses. All these collapses were considered massive pillar collapses because many pillars were involved. In the violent pillar collapse case, the width¬to-height (w/h) ratio was less than three; although, the pillar safety factor (SF) was more than 1.3. There was a collapse of about 100 pillars in less than three hours. The objective of this study is to determine the mechanism of pillar collapse for this violent pillar collapse. Convergence monitoring and numerical modeling were applied to combine field data and theory to simulate the pillar collapse. Convergence field measurements introduce the arc-effect behavior for the roof. The results showed that other factors besides pillar geometry caused the pillar failure. Other parameters, mainly dip of the coal seam and presence of fractures and faults may affect the strength and failure mechanism of a pillar.

Jan 1, 2004

By Stephen C. Tadolini

The U.S. Bureau of Mines (USBM) is conducting research to provide alternatives for traditional secondary support methods. These cost-saving methods are proving to afford safer installation, improve entry stability, eradicate material-handling injuries associated with crib supports, and enhance ventilation. In cooperation with Mountain Coal Company, the USBM replaced timber cribbing with high- strength cable supports to provide stability in a gate road that was used for two longwall panels. The support design consisted of 2.1-m (7-ft) full-column resin-grouted bolts and 4.8-m- (16-ft-) long high-strength resin-grouted cable supports. Three support concepts were evaluated: passive, stiff, and tensioned systems. Cable loading and roof deformations were monitored to evaluate the behavior of the immediate and main roofs during panel extraction. The stress and loading histories for both panels and the abutment and yield pillars were monitored to assist in evaluating the stress transfer and pillar performance in conjunction with the roof behavior. The test results indicated that resin- grouted cable support systems successfully maintained the immediate and main roofs during the extraction of two longwall panels. This paper describes the theory, application, and advantages of resin-grouted cable supports and presents the mine measurements made to assess the cable performance during the retreat process of longwall mining.

Jan 1, 1994