Search Documents

By G. K. Rogers

Portals, which are the surface entrances to underground excavations, are frequently overlooked and often difficult areas In terms of ground control. Failures commonly occur In the typically high angle approach cuts and Initial subsurface portion of the portal. In order to permit rigorous design of all types of portal structures, failures are Identified and subsequently classified. Based on the failure classification and suggested analysis methodology, optimum ground and support loading can be determined.

Jan 1, 1988

By Jay Keng

During the construction of shaft on the fractured and weak rock strata, the stability of construction plays an important role. This study includes earth stress estimation, support method, and stability analysis. Stresses on the site of three shafts include structural residual stresses, earth pressures, and hydrostatic pressures were determined. The basic method of estimating the support strength is dependent upon the' size of the plastic ring after rock excavation. During the construction of the shaft, geotechnical measurements, physical properties of the rock, and the change after excavation have to be evaluated again. Geology and construction methods need further consideration.

Jan 1, 1988

By K. Y. Haramy

Strong roof helps minimize roof fall problems in coal mine entries. However, the Inability of strong roof to cave readily may contribute to major ground control problems In Iongwall and retreat mining operations. The concern expressed by mine operators prompted this Bureau of Mines study to analyze the effects of strong roof members on ground stability around Iongwall openings. The problem was approached from three directions: development of a theory to analyze the strain energy conditions In the coal and surrounding strata, modeling the effects of different thicknesses and strengths of Coal and roof strata, and field Instrumentation of powered supports In two Iongwall mines. Results from the theoretical and modeling analysis confirm the accepted belief that a strong roof does, In fact, play a major role in high stress concentration problems In and around the Iongwall panel. Analysis of the effect of different roof overhang dimensions and properties on relative strain energy buildup In the coal and roof Is presented. Shield pressure data Indicate possible methods for detecting noncaving roof behind the shields. Strategies to monitor roof overhang and control dangerous conditions caused by the noncaving roof are also presented.

Jan 1, 1988

By Gennaro G. Marino

Documented case histories of surface ground movements from mine subsidence were utilized to help determine when the initial collapse of the overburden occurred above longwall panels. By studying this relationship between initial movement at the surface and the amount of face advance, the least-complex conditions exist for empirically assessing the span capacity of the overburden. The objective of this work was to obtain a better understanding of the overburden response to longwall mining. This knowledge will give a better insight on the long-term effects that different overburden types have on the stability and the subsidence potential of room and pillar mines, as well as, the influence of the overburden on subsidence over longwall panels. Theory on the overburden span capacity was developed and correlated to field observations. Data were used on the overburden lithology, depth, width, and face advance of the panel, and the subsidence conditions that were noted on the surface. The subsidence measured on the surface was used to determine when complete failure in the overburden rock had occurred. According to spans predicted by theory and the subsidence measured in the field, the competent lower units failed at a face advance less than when significant subsidence was observed on the surface. In each case studied, there were competent lower beds; however, the full overburden weight was not sustained to the point of subsidence. The best correlation with the surface movement was found with the most shallow, competent bed. Elastic plate solutions with various support conditions were found to best monitor the surface subsidence of these upper roof units.

Jan 1, 1988

By A. Wahab Khair

This paper presents an analysis of surface ground movements recorded from two longwall mines in Northern West Virginia which operate in the Pittsburgh Seam. The instrumentation areas consisted of four panels, two at each mine, covering various sections with unique topographic features. Instrumentation consisted of survey monuments on 25 to 120 ft. spacing. Vertical and horizontal ground movements were measured at specified intervals to determine subsidence rate, developing and final subsidence profiles, angle of draw, horizontal displacements and associated strain profiles. A relationship between panel depth and width and the subsidence factor was also developed.

Jan 1, 1988

By Christopher Mark

The Bureau of Mines is conducting research to assess the effectiveness of different chain pillar designs in maintaining gate entry stability. The study described in this paper was performed in a 1200 ft long, experimental headgate section which contained three pillar designs: - a three-entry, yield-abutment pillar' system, - a four-entry, yield-yield-abutment pillar system, and - a five-entry, all-yield pillar system. As the longwall mined by the experimental section, Bureau engineers monitored entry convergence, roof sag, and changes in roof quality. The results of the study indicate that the all-yield system performed at least as well as, and probably better than, the two abutment pillar systems.

Jan 1, 1988

By Denise Y. Dixon

The objectives of this study were to (1) document the hydrologic impacts of longwall mining on ground water, (2) identify the factors which affect the extent of dewatering, and (3) develop empirical trends to predict the extent of dewatering and recovery in advance of mining. The study was confined to three mine sites in north-central West Virginia. At each site, available ground water supplies were identified and monitored for dewatering effects and recovery. Mine A, located in Upshur County, West Virginia, has relatively thin overburden (approximately 715-280 feet). At this site domestic water supplies and specially constructed monitoring wells were monitored, continuing with an earlier study done by Cifelli arid Rauch. Most such supplies were completely dewatered over the longwall panel. Some of these wells have shown significant recovery, especially near a stream. Extensive monitoring of two nested piezometer wells revealed that dewatering generally started in advance of undermining in the lowermost monitored overburden zones first and then progressed upwards. Most dewatered wells completed in bedrock have shown no recovery, except. for valley drilled wells located within 100 feet of a Stream. Affected dug wells completed in valley alluvium rend located within 200 feet. of the nearest stream have shown significant recovery. Some wells have partially collapsed following mine subsidence. Mine B, having relatively thick overburden (approximately 585 to 900 feet), is located in Monongalia County, West Virginia. Ground water supply surveys have been conducted there in an attempt to study past dewatering effects. Owners reported Chat several wells were dewatered by longwall mining arid vertical air shafts that preceded longwall mining. Dewatered wells over longwall panels hove shown some recovery within 3 ½ years of mining. Mine C also has relatively thick overburden (approximately 585-900 feet), and is located mostly in Greene County, Pennsylvania. In addition to a survey of domestic water supplies at this site, five specially constructed monitoring wells were tested. The shallow monitoring wells suffered drops in water level due to mining but totally recovered within one day to three weeks after dewatering occurred. However, they did occasionally exhibit partial collapse during mine subsidence. Subsidence fracturing was beneficial in increasing the lateral hydraulic conductivity by a factor of about S to 22 for rock strata located within 124 feet of the surface, indicating enhanced shallow aquifer potential. One deep well suffered both partial dewatering and structural damage, with the state of water recovery bring uncertain. Also, two shallow domestic supplies out of five located over the mine were reportedly dewatered, but this claim could not, be substantiated.

Jan 1, 1988

By M. Guana

Island Creek Corporation is predominately an underground mine operator deploying room-and-pillar and retreat longwall mining methods for extracting coal. Wide variations are encountered in overburden depth, stratigraphy, and insitu stress fields. This requires major adjustments in mine design among mines and occasionally within a mine. Simple rock mechanics principles are utilized in mine design to optimize safety and productivity. Physical observations and micro deformation monitoring of roadways are the primary techniques employed. Pillars and artificial support systems are the primary design elements modified. The specific case histories reviewed in this paper include narrow panels with high extraction for conventionally mined rooms, pillar sizing for longwall gate entries at great depths, and bolt type selection for difficult ground conditions.

Jan 1, 1988

By Thomas Rymer

Mathematical modelling of mine subsidence measured at 21 locations in Pennsylvania and northern West Virginia allows for the refinement of current methods of predicting maximum land subsidence associated with longwall coal mining. This new method (RYBAD model) is an extension of that provided by Tandanand and Powell (1984; TP Model). The RYBAD model accomplishes more accurate subsidence predictions (error typically less than 10 percent) for a greater range of mining and geological parameters through the recognition of the following: 1) subsidence increases at a decreasing rate (curvilinear relationship) with greater overburden thickness up to a critical value beyond which subsidence decreases; 2) subsidence is strongly influenced by the stratigraphic proximity of strong rocks to the coal (size of potential caving zone); and 3) subsidence index is related to overburden thickness by a family of curves, each for incremental variations in the effective percentage of strong rock in the overburden.

Jan 1, 1988

By Kanaan Hanna

The integrity factor approach was developed by the Bureau of nines to assess the stability of mine pillars and has been applied primarily to longwall chain pillars. Recently this approach was applied to a room-and-pillar mine in the Illinois Coal Basin. A special configuration of hydraulic borehole pressure cells was installed in a pillar to determine the in situ strength-and- stress relationship of the coal pillar and to verify the applicability of the integrity factor approach. Results indicate that the integrity factor approach is applicable to the assessment of pillar st6b:lity and nay bs a realistic and effective approach for room-and-pillar mine design.

Jan 1, 1988

By R. J. Morrell

The Bureau of Mines developed a ground support system for use with an underground coal auger. The system consists of inflatable airbags that are inserted in the holes as they are drilled, and then gradually deflated to provide controlled roof caving. This paper presents results of laboratory and field tests of the system that show it to be technically feasible.

Jan 1, 1988

By H. N. Maleki

Extensive measurements and underground observations in three Western U. S. coal mines are integrated in this paper to determine in-situ pillar load-deformation characteristics for narrow (30 it wide, 80 ft long) pillars in two-entry gate road systems. In spite of similarities in the regional geology, coal pillar laboratory mechanical properties and gate pillar geometries, the pillar peak strength, post-failure behavior, and failure mechanism were shown to be significantly different. Pillar peak strength was shown to be dependent on depth at one site, approaching burst-prone stress levels of 4000 psi. At another site, the pillar peak strength was lower because of lower confinement; this was related to the higher frequency of cleats and the lower friction- al properties of the roof/floor and coal contact. Two failure mechanisms were identified - one in the pillar, and the other in the mine floor. The roof stability was good at all three sites because of the thick-bedded nature of the roof strata and limited total gate span in a two-entry system. Existing pillar design techniques were shown to be inadequate for design, requiring adjustments for depth of cover, cleat frequency, and roof /floor frictional properties.

Jan 1, 1988

By P. Gaskell

The paper examines the development of rock movement between a longwall extraction horizon and the surface for a fully caved mining situation. Physical modelling has been used to examine the mechanics of ground movement and the propagation of fractures around the longwall working. The paper discusses dimensional analysis, model construction and measurement technique and data processing of the results into effective graphical forms for further study.

Jan 1, 1988

By Thomas H. Wilson

Common offset and refraction seismic data have been collected over four longwall panels at two different locations within West Virginia. Surveys prior, during and after mining were made in both areas. The velocity of seismic wave propagation in the overburden rocks is observed to decrease in response to panel emplacement. Variations in the magnitude of this reduction, apparent as an additional first arrival time delay in the after mining common offset surveys, do not appear to correlate directly to the amount of subsidence that has occurred. Velocity reduction and signal absorption zones are also produced in the cover beyond the panel face over the adjacent unmined areas. Signal absorption and velocity reduction zones have also been observed over room and pillar entry areas between mined panels. Velocity reduction zones have been- observed beyond the panel face in both shallow and deep mines, but the signal absorption zone has not been observed over the deeper mine. Changes in the compressional wave velocities of the cover rocks are associated with changes in their elastic moduli. Differences between borehole derived and surface seismic derived interval velocities, are related to differences in the properties of the bulk volume sampled by each method.

Jan 1, 1988

A computerised influence function approach to subsidence and horizontal displacement prediction is described, with particular emphasis being placed on the applicability of the method to irregular- shaped mine workings. Based on previous work [1], this approach has been put for- ward for inclined seam situations. Examples of graphical output presenting surface subsidence contours, horizontal displacement vectors and principal strain vectors are given and their significance discussed in relation to current problems.

Jan 1, 1988

By Ian W. Farmer

A description of the factors causing outbursts and rockbursts in coal mines is given. The mechanics of both outbursts and rockbursts can be described in terms of conversion of stored strain energy in the coal and surrounding rocks into kinetic energy through failure. The major difference between the two phenomena is that gases adsorbed onto the coal structure and desorbed during deformation contribute to the energy available during outbursts and may also affect the loading and unloading characteristics associated with failure. The amount of energy involved and the type of phenomenon are related principally to gas content depth and rock behavior.

Jan 1, 1988

By P. R. Sheorey

Four case studies of special geomining conditions from Indian coalfields are discuss- ed. These cases relate to (a) pillar extraction in two seams simultaneously under a difficult roof (Satpura I and II). (b) depillaring in an inclined seam resulting in rib instability (Sudamdih), (c) depillaring resulting in floor lift and side spalling (Jarangdih) and (d) contiguous pillar extraction under hard incavable strata. Solutions to these problems are given based on rock mechanics principles involving stress analysis, classification techniques, past experience and engineering judgement.

Jan 1, 1988

By John J. Bowders

The stability of surface slopes undergoing subsidence due to longwall mining was investigated to examine the effect the subsidence had on the stability of the slopes. Stability analyses were performed on all slopes along both longitudinal and transeverse sections of the longwall panel before and after subsidence. Both finite- and infinite-slope analyses were performed with both drained and undrained cases. The results indicated that the changes in the stability of slopes due to subsidence were insignificant for the cases analyzed. Although significant lateral ground movements were recorded, these were not attributed to slope failure. Explanations for these movements are presented in the paper.

Jan 1, 1988

By Deren Zhu

Based on the results of field observation and physical model analyses, a computer simulation method, FEAEBP, has been developed for simulating the breakage of the main roof by considering it as a Kirchhoff plate on Winkler elastic foundation. By this method various parameters of rock property, different boundary conditions of the working face and the initiation, development and results of the breaking process of the main roof with different geometric dimensions can be effectively simulated. Since the main and immediate roofs, and the coal seams are treated as an integrated mechanical system, the interaction among them can be studied in detail.

Jan 1, 1988

By J. M. Krese

This paper gives an overview of the National REAP program emphasizing the program's current status and future plans. A brief historical review of the program will be given containing roof-fall accident trends and statistics. The latest developments in roof control technology and training as it affects the REAP program will be presented. A brief discussion concerning some effects of the implementation of the amendments to Part 75, CFR, concerning roof support is included.

Jan 1, 1988