Search Documents

By Terry Mandziak

Typical leach mine operations recover gold values through the application of a dilute cyanide solution onto ore within an engineered facility. Key to the success of mining operations is the, containment and management of the cyanide solutions within the facility. Properly engineered' facilities will have containment systems that are both protective of the environment while enhancing solution recovery. This paper not only discusses general containment standards, but identifies state-of-the-art containment and monitoring practices;

Jan 1, 1998

By Nobumasa Kemori

Six kinds of copper '90ncentrates. were treated individually in a ,pilot scale. Outokumpu flsah smelting furnace ~n order to study their ?flash smelting behavior with respect to oxygen efficiency and dust generation. The copper concentrates tested were selected from the more than twenty sources which are treated at the Sumitomo Toyo copper smelter, so as to provide a wide range of chemical composition in terms .of Cu, S,Fe, Pb + Zn + As, and Si~ content. Oxygen efficiency 'and dust generation rates obtained in 'the experiments ranged from 80% ,to 108% and 11% to 20%, respectively. Relationships between these results and experhnental conditions such as chemical and mineral composition of the copper concentrates, flux ratio, fuel consumption and so on are also discussed quantitatively in this paper.

Jan 1, 1998

By Larry M. Southwick

Steel mill electric arc furnace dust is a RCRA listed hazardous waste and its treatment and/or disposal are regulated by a complex set of rules. These regulations were originally established to encourage recovery and recycling of valuable components. For EAF dust, the more valuable constituents include zinc, lead, cadmium and iron. In fact, current trends are in the opposite direction, as the regulations have complicated the ability to commercialize new treatment technologies and created substantial roadblocks and liabilities for processors. As a result, almost half of the EAF dust generated in 1997 will be landfilled. The problems are compounded by difficult processing requirements, less than sterling examples of technology development and mechanical and operating problems. This paper explores some options to simplify the processing requirements and thereby easing difficulties in commercializing new technologies and expediting the recycling of recovered metals. Dust processing usually includes a simple step followed by two complicated steps. The simple step is fuming of heavy metals away from iron and other residues. The complex steps are (1) separating and purifying the heavy metals and (2) upgrading the iron residue. The first complex step can be simplified by producing an intermediate product that is amenable to processing by zinc refiners. This route benefits from the currently underutilized (by dust processors) resource offered by refiners, who have experience in and existing processes for separation and purification of zinc-based heavy metals. Various processes and their associated product options are reviewed and compared. Future directions for dust processing developments are suggested.

Jan 1, 1998

By Shunli Zhang

Metals recovery from electronic scrap by physical separation may provide an alternative to the current recycling approach, through which halogenated flame retardants can result in hazardous dibenzo-p-dioxins and dibenzo-furans. On the basis of a complete sink-float analysis of personal computer and printed circuit board scrap, and in view of the advantages of dry processes for electronic scrap recycling by mechanical separation, air table separation is prioritized in an attempt to separate metals from plastics and glass involved. In the present paper, theoretical and practical considerations of air table separation have been detailed. It has been shown that air table separation is effective for recovering copper and precious metals from this specific waste stream. With the feed rate of 60 kg per hour, the combined grade and recovery of copper, gold, and silver attainable for the two heavy products produced by the air table used in the present study was shown in the following table:

Jan 1, 1998

By Michel Boisvert

Noranda Metallurgy is presently completing construction of the new Noranda Converter (NCV) at its Home Smelter in Rouyn-Noranda. This capital investment of CDN$56M is the continuation of the Emissions and SO2 Reduction Program that was initiated in the late 1980s with the acid plant for Reactor off-gas treatment. The Patented Noranda Converter was developed and pilot tested at the Home Smelter in the early 1990s. The project will replace the Peirce-Smith Converters and enable sulphur fixation to be 'increased from 70% to over 90% by 2002 with an accompanying reduction of dust emissions to the atmosphere. The construction site is an extension of the present Noranda Reactor area. A number of existing facilities including the acid plant and process air supply were used to minimize the capital cost of the project. This paper provides a brief history of the Noranda converting process, the Home Smelter Emissions and SO2 Reduction Program, ,project implementation and construction, a description of the different facilities, and preparation of human resources for start-up.

Jan 1, 1998

By Garth James

Bacterial consortia capable of degrading cyanide and metal-cyanide complexes were obtained from gold mine process waters using enrichment cultures. The cultures contained either cyanide, tetracyanonickelate, or ferrocyanide as a sole nitrogen source. Several bacteria were isolated from the consortia, but none of these organisms were capable of degrading cyanide or cyanide-metal complexes at rates equivalent to those of the intact consortia. The consortium from the cyanide enrichment was capable of completely degrading cyanide from an initial concentration of over 100 ppm in less than one day, when cultured using a fed-batch method. Tetracyanonickelate and ferrocyanide were degraded more slowly. Overall, these results demonstrate that bacteria capable of degrading cyanide and cyanide-metal complexes can be isolated from mine process solutions and are capable of significantly reducing cyanide concentrations under appropriate conditions.

Jan 1, 1998

By Emil B. Milosavljevic

Problems associated with distillation and other classical methods for analyzing operationally defined cyanide (CATC, WAD, Total and Free Cyanide) will be discussed. These methods often achieve incomplete, species dependent cyanide recoveries and suffer from serious interferences. Depending on the relative concentrations of interferents and other matrix constituents, underestimation (ultimately Type II errors probability of not detecting a constituent when it is actually present) or overestimation (ultimately Type I errors -probability of deciding a constituent is present when it is actually absent) of the cyanide levels present in a ,given sample may occur, causing in the first case false security and in the second case, excessive cyanide treatment costs. Mahy, if not all, enumerated problems can be solved by using novel flow injection (FI) gas-diffusion amperometric methods. A modification of the recently approved FI ligand exchange (FIILE) method for determination of available cyanide (USEPA Method OIA-'l677) that obviates sulfide interference will be discussed. Eight laboratory round-robin data obtained for the FI UV -digestion (FIIUV) method that determines total cyanide (Proposed Method OIA-1678) will also be presented. In addition, some methods for cyanide speciation will be presented. Finally, research needed for developing reliable methods for determination of operationally defined cyanide in solid samples will be summarized.

Jan 1, 1998

By S. Ozbilen, B. Erdogan, M. Erdogan

To study by thermal analyses the response of precipitation hardenable alloys of Al-Cu-Mg and Al-Li-Cu-Mg system to natural and artificial ageing, a series of ternary and quaternary Al-alloys with nominal compositions of Al-l.13wt%Cu-0:65wt%Mg (alloy-I), Al-1.15wt%Cu-0.57wt%Mg-0.07wt%Li (alloy-2), Al-l.19wt%Cu-0.56wt%Mg-0.75wt%Li (alloy-3), Al-2.0lwt%Cu-0.89wt%Mg (alloy-4), Al-2.14wt%Cu"0.56wt%Mg-0.07wt%Li (alloy-5) were used in the present investigation. Samples in the form of rolled sheets are subjected to water quenching at 25EC after solution treatment at 530EC for 20 min. Alloys were aged naturally at room temperature (25EC) up to 2 months and artificially at 190EC up to 2 days. By using differential scanning calorimetry (DSC) in the temperature range of25-300EC, differential thermal analysis (DTA) in the temperature range of25-600EC together with Vicker's hardness measurements, the response to natural and artificial ageing of the alloys used in the present study were investigated. It was observed that in these alloys, GPB(Cu, Mg) zones [Guinier-Preston zones with Cu and Mg] do form during water quenching at 20EC following solutionizing heat treatment. Natural ageing of the same alloys causes formation of more GPB(Cu, Mg) zones, which results in hardening in the alloys. Artificial ageing at 190EC up to l day results in GPB zone dissolution causing preliminary decrease in hardness values while two days of artificial ageing in the alloys cause S' (Al2CuMg) precipitation confirmed by DSC/DTA analyses resulting in an increase in hardness values. Li addition up to 0.75wt% helps T1 (Al2CuLi) and T 2 (Al6CuLi3) phase formation together with S' precipitation as DSC/DTA analyses show after the same heat treatment.

Jan 1, 1998

By James L. Whitlock

Biological treatment of mining and industrial effluents reached full scale commercialization around 1980. These proven, low cost, technologies have been limited in application due to a number of factors, including extended periods of time and cost required for pilot testing as compared to chemical treatment technologies, lack of biological expertise in metallurgical personnel, longer treatment periods in some cases, and performance failures based on improper application. Renewed interest in biological treatment technologies is being driven by permits with lower effluent concentration criteria, permits with bioassay evaluation, the need to remove thiocyanate, nitrates, sulfates and? other parameters. Chemical treatment processes, in general, have not been able to meet these present requirements, or require elaborate? combinations of processes, in terms of effluent quality and treatment economics. This paper addresses biologieal treatment of mining and industrial waste waters and selected recent advances in these technologies. The future looks very bright for application of these low capital and operating cost technologies,

Jan 1, 1998

By E. Fockedey

he destruction of free cyanide on a Co3O4 doped carbon felt was studied. The experiments were done with an eiectrochemical filter press cell on dilute alkaline solutions containing 250 mg/l NaCN. No chloride ions were added to the solutions. The cobalt oxide protects the felt against corrosion and has a catalytic effect on the degradation of the cyanide. This kind of electrode allows working with current density as high as 1200 Aim without any visible degradation of the felt. The most interesting results were obtained with a current density of 400 Aim' at which the cyanide concentration can be lowered to 5 mg/l with a current efficiency of more than 70 % and a specific energy consumption of about 10 kWh/ kg CN.

Jan 1, 1998

By N. Kanari

Chalcopyrite concentrates and their pure constituents were chlorinated by C12+N2 between 25 °C and 750 °C. The reaction products were analyzed by SEM, XRD and chemical analysis. The effect of gas flow rate and chlorine content of the gas mixture on the reaction rate were investigated. At room temperature, these solids start to react with chlorine giving metal and sulfur chlorides. Complete reaction is achieved at about 300 °C and the iron and sulfur chlorides were fully volatilized. The chlorination residue is composed of valuable metals' chlorides. A simplified flow - sheet for the treatment of chalcopyrite concentrates by chlorine was suggested.

Jan 1, 1998

By Rubén Alvarado

The markets and environmental protection rules are more and more exacting, both of which have determined that copper smelters should look for technological development and global management to ensure their viability and competitivity in the short and long term. The main facilities of the present and future Smelting-Converting Process at Codelco's Caletones Smelter, is based on Teniente Converter reactors with a high operational availability that have reached concentrate processing capacities near 2,000 tpd. These reactors are in operation in most of the smelters in Chile as well as in Zambia, Peru, Mexico and, in ?the near future, in Thailand. Since 1993, the Smelting-Converting process of the Caletones Smelter of Codelco-Chile has been based on one Reverberatory furnace, two Teniente Converters and four Peirce-Smith Converters. These facilities, together with the operation of two Fluidized Bed Dryers, three Slag Cleaning Furnaces, and two Oxygen Plants have allowed the smelter to reach concentrate smelting capacities and copper productions of 1,215 kt/year and 360 kt/year, respectively. This transitional operating scheme, combining together traditional and advanced technological equipment, needs further modernization to successfully face the modern world challenges, especially with relation to the environmental commitment, production costs and wide satisfaction of customers. For this reason, for the period 1997-2000, a Modernization Plan has been worked out. This plan considers an increase of the present throughput, which will permit a significant increase in productivity, as well as finding a definitive solution for meeting the environmental regulations. Among these projects, we can point out the definitive shut down of the Reverberatory Furnace, which is a contaminating piece of equipment of low energetic efficiency. Additionally, it considers the installation of two new Slag Cleaning Furnaces, one additional Oxygen Plant, and the incorporation of two new Sulphuric Acid Plants with a production capacity of 4,500 T/D, that will recover over 92% of the sulphur content, of process off-gases.

Jan 1, 1998

By Richard H. De Voto

The McDonald Gold Project and two satellite gold deposits near Lincoln, Montana, contain at least 9.9 million ounces of gold and 30 million ounces of silver. The McDonald gold deposit alone contains 7.2 million ounces of gold reserves that can be open-pit mined and processed by cyanide heap leaching at a projected cash operating cost of $190 per ounce. The deposit is predominantly oxidized with no chance of acid production, and can be mined, operated, and reclaimed with minimal permanent environmental disturbance other than the creation of an open pit filled with a fresh-water lake which would support trout. The Seven-Up Pete Joint Venture, the owner of the McDonald Gold Project, commenced permitting of an open-pit, heap-leach operation in November 1994. In 1998, Montana citizens passed an anti-cyanide, open-pit mining initiative, 1-137, which banned any new open-pit gold mine which uses cyanide processing, The Venture has conducted extensive studies, including metallurgical testing of the treatability of McDonald ores with alternative lixiviants, and has determined that all other mining and metallurgical treatment systems are vastly uneconomical in the recovery of gold and silver from the McDonald deposit. Therefore, the Venture's proposed open-pit mining and cyanide heap-leach processing is the only technology that can be applied economically to the McDonald deposit. Further, the analyses convincingly demonstrate that the proposed open-pit, cyanide heap leaching technology results in maximum resource conservation of this valuable and unique deposit and poses far less risk to human health and the environment than any of the alternative technologies.

Jan 1, 1998

By Martin Brueggemann

In 1993, the El Paso Smelter began operation of the first commercial CONTOP copper smelting furnace. The CONTOP process was chosen for the plant modernization due to its low capital cost and the ease that it could be incorporated into a 100 year old existing smelter. After four years of operation, CONTOP has proved itself to be a reliable copper smelting technology. This paper will discuss a brief start-up history, current operation, and future modifications and improvements.

Jan 1, 1998

By Paykan Safe

This paper reviews various process off-gas cooling options available for sulfide smelting processes. Advantages and disadvantages of each, system are discussed along with the selection criteria for a reliable and cost effective :system. Various systems are presented to demonstrate typical process parameters for smelter off-gas handling systems and to outline operating difficulties associated with each system:

Jan 1, 1998

By E. Oshima

In May 1991, a New Mitsubishi Continuous Copper Smelter Line started operation at Naoshima. Recently, it has been continuing steady operation and one and a half year campaign life has been achieved. In 1996, new records of on line time, the amount of copper concentrate treated and copper anode production were achieved. 1t proves the superiority of the process with respect to pollution control, energy efficiency, flexibility and easiness of the operation and over all economy including off gas handling cost. Furthermore, .plans are underway to prolong the campaign life for two years and to improve the process efficiency. This paper describes recent operation, improvements, and a future capability study.

Jan 1, 1998

By Tuula Mäkinen

One of the latest applications of the Outokumpu Flash Smelting Technology is the direct smelting ,of nickel concentrates to metallised low-iron nickel mattes. Compared to the conventional nickel smelting, the new DON process needs a lower number of smelting vessels resulting in considerable economic and environmental benefits. Fundamentals of smelting nickel concentrates in one stage to low-iron mattes are presented. Properties of nickel. smelting slags with an emphasis of the slag fluidity at high MgO-levels are also discussed. Conditions prevailing in DON mattes at high oxidation degrees are presented as well as their influence on the behaviour of such mattes in the settler and on tapping the furnace. Distributions of elements in the direct smelting are presented and compared with the conventional process. A further comparison is made with pilot-plant data and the industrial scale.

Jan 1, 1998

By Dorothée Proffit

Characterization of solids containing cyanides is carried out according to recommendations and standard guidelines. Most of these procedures are based on the analysis of leachates collected either on site or after leaching in the laboratory of samples. Unfortunately, these sole results are often insufficient to identify the source of the pollution. To provide 'a more complete characterization of polluted solids, optical and electron microscopy, XRD, Mossbauer spectroscopy, and transmission infrared spectroscopy were combined to analyze leachates and raw or ground samples. This combination of techniques allows the determination of the kind of cyanoferrate complexes are present in the solid state, different from insoluble Prussian Blue, since they do not have the same extraction' behavior. The use of all these techniques to characterize solid samples combined ,to the usual analysis of solutions gives a better understanding of ' the cyanide behavior.

Jan 1, 1998

By D. Mukerjee, Ramen Datta, Sanak Mishra, R. Veeraraghavan, K. L. Rohira

"Recent efforts at Steel Authority of India Limited (SAIL) has led to the successful development of atmospheric and marine corrosion resistant high tensile Thermo Mechanically Treated (TMT) bars with minimum specified yield strength of 50 kg.mm-2. These rebars are increasingly being used for a wide range of end-applications, namely, concrete reinforcement structures, bridges, flyovers, dams etc. Welding is an important processing tool for each of the above applications. In view of the importance of welding, a comprehensive evaluation of the weldability properties has been carried for the two grades of steels using Submerged Metal Arc Welding (SMAW) process; the most popularly used technique of welding of reinforcement bars (re bars).Implant tests were conducted to assess the cold cracking susceptibility of the steels. The static fatigue limit (SFL) value, determined for the atmospheric corrosion resistant (Cu-TMT) rebars under no preheat and no rebalcing conditions was found to be 63.8 kg mm-2, which was significantly higher than the Minimum Specified Yield Strength (MSYS) (50 kg.mm-2). This indicates adequate resistance to hydrogen induced cracking (HIC). On the other hand, the SFL value obtained for the marine corrosion resistant rebars (Cu-Cr TMT) under no preheat, no rebaking conditions was found to be inconsistent. Repeat of the test with fully rebaked electrodes (350°C-2h) resulted in a high SFL value (60.3 kg mm-2)_The rigidity of the structure or restraint influences the susceptibility of the weld joint to cracking. The cracking tendency increases with restraint intensity (K) of an assembly. The critical restraint intensities determined for the two steels were found to be· in excess of 1680 kg/mm.mm, indicating good welding behaviour with the following welding conditions : for Cu-TMT rebars with no preheat and no rebaking and for Cu-Cr TMT rebars with no preheat and fully baked electrodes; that is under low hydrogen levels."

Jan 1, 1998

By Aïda Espinola

Decontamination of synthetic solutions containing cadmium ions using coconut fibers in natura was investigated in laboratory scale. Cadmium ions, a serious pollutant of water ways, where it is detrimental to the environment, may be absorbed by fish and mollusk used as food, which will, eventually, poison humans; these ions are usually present in minero-metallurgical and electroplating industrial effluents. Usually employed for the aqueous effluents treatment are chemical precipitation, adsorption and electrolytic processes. Precipitation is not effective for cadmium removal, because of the high KpS of the cadmium hydroxide, which requires high pH; only sulfide would be efficient in cases of very small amounts. Some vegetal refuses have shown to be practical for absorption processes of several metallic ions. We have applied coconut (Cocos nucifera) shells, which are extremely abundant over most of the extensive Brazilian coast, in the removal of cadmium: it has been verified, in our laboratory, that the surface of the fiber of this coconut is rich in chemical compounds which are active scavengers for Cd2+. For the optimization of the process, hydrosoluble components existing on the surface of the fiber, which may be deleterious, were previously washed out by water, and variables, such as the pH and the proportion of mass of fiber to volume of solution, were adjusted. As much as 99% of the initial contaminant metallic ion has been eliminated, resulting a solution to be discarded which contains ca. 0.1 ppm; this attends to the maximum impurity legally admitted by the environmental control agency of Rio de Janeiro, FEEMA, for cadmium ions in aqueous effluents to be disposed in rivers and in the Guanabara Bay area.

Jan 1, 1998