Search Documents

By A. S. Mustafinova, A. A. Zharmenov

"Production of electrolytic copper is characterized by large volumes of acidic spent solutions the utilization of which requires considerable expenditures of neutralizing agents. At present, an economically substantiated technology does not exist for treatment of sulfuric acid rinse solutions and spent copper electrolyte which will allow for repeated use of the acid and the metal salts. Therefore, for this aim the most advantageous is the use of electromembrane methods. In the paper there is stated the essence of developed technologies which are distinguished by low waste and provide the extraction from the solutions of metallic copper, nickel and sulphuric acid. There are also considered methods of copper electrolyte processing allowing to regulate its composition by that or another component (H2S04, Cu, Ni, As).On the base of the detailed study of the behaviour of various types of ion- exchanger membranes in copper-, nickel-, zinc-, arsenic- bearing sulphate solutions there is realized the selection of the most suitable membranes (MK -401, MA-411, MB-2 and MKL-l/MAL-2).Some variants of electro membrane processing of spent solutions of the hydrometallurgy process have passed productions tests on a number of copper-electrolyte enterprises of the countries of CIS (cooperation of Independent States). These tests showed high efficiency of developed methods."

Jan 1, 1997

By Fathi Habashi

"Davy, Faraday, and Bunsen laid the foundation of electrometallurgy which had a· great impact on other areas of metallurgy. Electrometallurgy is presently dominated by the production of aluminum, the electrorefining of copper, and the electrowinning of zinc. It has also been successful in the electrowinning of copper from solutions obtained by leaching-solvent extraction. Electrowinning processes, however, are capital intensive. Improvement of the present technology should be intensely investigated especially when it is expected that such processes will increase greatly as a result of a shift from certain pyrometallurgical processes to pressure hydro metallurgy.INTRODUCTIONPyrometallurgy was used for thousands of years to produce copper and iron from their oxide ores!). Today it is still the only route to produce iron and steel and it is certain that it will remain so for many decades to come because pyrometallurgy is most suitable for the treatment of high grade oxide ores. Even when high grade iron ores are exhausted, it is possible to beneficiate the low-grade ores and produce pellets suitable for reduction in the blast furnace, which is a very efficient reactor, being a heat exchanger as well. Hydrometallurgy on the other hand can be traced to the time of alchemists in the Middle Ages when they were seeking to transmute base metals into gold, and thus were able to prepare many acids and bases which are the essential leaching agents."

Jan 1, 1997

By Philip L. LeHoux

"Kennecott Barneys Canyon Mining Co. is a gold heap leaching facility that has been in operation since 1989. In 1994, a flotation plant was commissioned to remove sulphide minerals from refractory sulphide ore. Tailings from the plant are mixed with oxide heap leach material in order to produce a geotechnically stable agglomerate from which the gold is leached and recovered in a conventional heap leach cyanidation process. The experience to arrive at an effective blending methodology is discussed.IntroductionAgglomeration is the practice of binding fine particles to coarser rock or other fines in order to avoid the deleterious effects of mobilizing the fines during the course of heap leaching(l-Chamberlin). Agglomeration has been considered a key component of successful operation at many heap leach sites. If the ore is of sedimentary origin and crushed, there is a high likelihood that the resulting product will contain a significant quantity of fines and a skewed gradation, that i~, a disproportionate amount of coarse and fine particles, with few in the intermediate size range. The exact methodology for determining whether the practice of agglomeration will have to be integrated into the operating scheme has been well discussed. These conditions are primarily geotechnical and geochemical. This paper will deal with the specific experiences of Kennecott Barneys Canyon Mining Company in modifying the agglomeration practices to suit evolving operational requirements."

Jan 1, 1997

By R. V. Kumar

"The use of sensors to monitor gaseous species in industrial processes is discussed. All of the existing systems have disadvantages. Sensors, based upon solid electrolytes, which can be placed directly into the gas stream are attractive but many also respond to oxygen, need to be sealed at high temperatures and require a separate reference. This paper describes sensors, usually based upon two electrolytes, which do not respond to oxygen and do not require high temperature gas seals or separate references. The application of these sensors to the measurement of carbon dioxide, sulphur dioxide and trioxide and hydrogen chloride is described. These sensors can be placed directly into the gas stream at elevated temperatures.IntroductionOn-line gas sensing is becoming more important as concerns regarding the environment mount. There are many established techniques for monitoring gases in industrial processes, with applications in safety monitoring, chemical analysis or process and emission control. Flue gas analysis involves the greatest technical complexity, requiring several sophisticated capital-intensive spectroscopic instruments for different species as well as needing highly skilled operators. There are also several instruments, based upon aqueous electrochemistry, which are available for the analysis of the gases S03, S02, N02 but these require that the gases are sampled at high temperature and cooled, prior to analysis. These instruments cannot be considered as giving on-line measurements of the gas composition. Furthermore, the power requirement of these instruments frequently precludes battery operation for field and domestic use."

Jan 1, 1997

By Leonard Harris, Rosa H. Harris

"It is becoming increasingly obvious to mining and exploration companies, when operating overseas, that their activities should not conflict with the interests of the surrounding communities. The world's largest gold heap leach operation, Minera Yanacocha has installed community assistance programs in Peru concerned with health, education, electrification, agricultural assistance and road improvements. The programs are conducted with joint venture partners consisting of the company, the community people, the contractors and suppliers, government and non government organizations and a ladies association composed of the employees' wives and female staff.IntroductionThe l 990's is the decade highlighted by enormous investments in mineral exploration and mining projects in the developing world. Figure 1 illustrates the distribution of exploration spending by mining companies in 1995."

Jan 1, 1997

By Kirsi M. Riihilahti

The oxidation characteristics of solid copper matte particles under simulated Kennecott-Outokumpu Flash Converting conditions are presented. This project is concerned with the determination of the effects of operating variables on the reaction of the particles. Experiments were carried out in a large laboratory-scale flash furnace with 72 wt-% Cu matte by varying initial particle size, temperature, oxygen partial pressure, oxygen-to-matte mass ratio and residence time. Chemical analysis was used to study the oxidation extent and copper volatilization. Particle fragmentation was examined. Fractional conversion and sulfur removal slightly decreased with initial particle size, while a higher oxygen-to-matte mass ratio mainly resulted in higher fractional conversion and more efficient sulfur removal. The fractional conversion values represented the overall extent of oxidation more closely than degree of sulfur removal.

Jan 1, 1997

By Cindy L. Williams

"The Blue Star subdistrict in the Carlin Trend, Nevada, includes multiple mines with 33.9 t Au in reserve and past production totaling 89 .1 t Au. The deposits are characterized by zoned alteration mineralogy and gold grades. From orebody centers outward the zones include: 1) a silicified core with erratic gold grade; 2) adjacent mill-grade (> 1.37 Au git) intense quartz-sericite-pyrite alteration; 3) enveloping leach-grade (0.21 Au g/t to 1.37 Au git) weaker sericite-kaolinite-quartzpyrite alteration; 4) surrounding decarbonatized and intensely argillized waste and leach grade ore; 5) pervasively decarbonatized waste rock; and 6) peripheral waste with weak decarbonatization and local propylitic alteration. Zoned alteration extends as much as 1500 m beyond orebodies.Understanding Blue Star subdistrict zoned alteration assemblages and gold grades has increased geologists' ability to provide practical and economically significant information to geotechnical engineers, mine planners and drill and blast personnel. Alteration influences geotechnical pitslope design because each assemblage has distinct rock strength. Geotechnical engineers use three-dimensional models of incompetent alteration types as a foundation for pit-slope design. In the drill and blast cycle, hard and soft alteration types require modified practices (powder column, blast hole spacing, delay design etc.) for optimum blast energy distribution. Further, geotechnically instable alteration types require careful blast procedures to prevent backbreak whic~ damages ultimate walls. In addition to mine planning and mining applications, zoned alteration assemblages extending beyond orebodies provide a useful exploration guide. Metallurgical character also varies with alteration type. Intensely quartz-sericite-pyrite altered or silicified ore has relatively high partical-size dependency and poor leach recoveries. Moderately sericite-kaolinite-quartz-pyrite altered rock, in contrast, shows little size dependency and good leach recoveries.The author sincerely thanks L. Schutz, P. Williams, C. Clode, W. Trudell, P. Herrera, M.DKunkel, M. Goings and numerous other Newmont geologists, metallurgist, engineers and support staff who made this paper possible."

Jan 1, 1997

By Gustavo Díaz, Miguel A. García, Carlos Frías

"Under the auspices of the Commission of the European Union, a consortium composed of six European organi~ations has conducted a project to scale up the PLACID electrowinning cell to industrial size within the Placid process development. This paper is concerning the results and achievement of the industrial cell prototype after more than 1,000 hours operating time and about 10,000 Kg electrolytic lead production. In general, results have been very satisfactory, demonstrating the ability ofthe PLACID electrowinning cell to produce top quality electrolytic lead (> 99.99 %) with high current efficiency and low energy consumption.IntroductionThis paper is concerning the development of an industrial size PLACID electrowinning cell within the PLACID process development. This project began on January 1993 and was finished on April 1996.Lead metal production and manufacturing industries produce large amounts of dusts and also lead bearing slags. Spent lead-acid battery recycling also produces lead oxides from the battery pastes rather similar to those mentioned above. Those lead secondary materials are hazardous and difficult to handle by usual procedures.Existing processes to treat-lead oxides may inflict considerable damage on the environment, incur high operating costs and have limitations to produce top quality lead.The main aim of this project has been to develop a novel hydrometallurgical process able to deal with different lead bearing materials, mainly lead oxide secondaries: lead-acid battery pastes, lead fumes, furnace slags, oxide residues, etc., producing ""four nines"" pure lead in an efficient manner with a benign influence on the environment; it is called the PLACID process."

Jan 1, 1997

By T. C. -M. Cheng

Iron removal and disposal in zinc plants has imposed a major environmental challenge to the industry. Among the existing options of precipitating iron as jarosite, goethite, and hematite, the Hematite Process seems to be the best candidate for the future development of a waste-free technology, because of its potential of producing saleable iron oxide residues for feed in iron-steel making industry. Unfortunately, under the current practice of the Hematite Process, it is not possible to produce iron residues clean enough to meet the specifications of the said industry. In this paper, the practice of industrial hematite precipitation and the relevant technical literature are reviewed with the objective to identify the critical processing parameters which are responsible for the contamination of hematite, particularly with sulfur and zinc. The analysis is conducted from a crystallization theory standpoint with emphasis given to the role of supersaturation with respect to the cleanliness of hematite precipitates.

Jan 1, 1997

By Nicholas S. Lynn

"A new process has been developed to bioleach refractory gold ores to expose the precious metal values using Thiobacillus ferrooxidans bacteria.The ore is hosted in a limestone rock with secondary replacement of carbonaceous and pyritic minerals. Crushing, stacking, bioleaching, rinsing and neutralization have been completed in a 45-day total time cycle. The use of sulfuric acid operation, and concentrated Thiobacillus ferrooxidans population allows the short bioleaching cycle.The ore is then processed using conventional Carbon-In-Leach Cyanide recovery techniques.ABSTRACT ONLY"

Jan 1, 1997

By Robert W. Bartlett, Keith A. Prisbrey

"Natural biooxidation of shallow, refractory ore heaps, relying on gaseous oxygen diffusion from the heap surface is attractive because of its simplicity and potential low cost, especially without using a lined pad, which is possible if percolation of leachate through the heap is avoided. In this case, the excess oxidation enthalpy must be removed by water evaporation from within the wet ore heap, and the rising water vapor flux within it will impede the downward oxygen flux. An analysis of this process shows that for typical values of pyrite grades and limited temperature increases in the ore heap, the oxidation rate and penetration into the heap is reduced to values between about 30 percent and 50 percent of those obtained when leachate percolation occurs and water evaporation is not a significant mechanism of heat removal.IntroductionHeap biooxidation of refractory gold ores, needed as a pretreatment step to liberate the gold for subsequent extraction by leaching, requires large amounts of oxygen for the normal amounts of sulfide minerals that are typically present, one to two percent pyrite and/or arsenopyrite.The importance and potential limitations of oxygen transport into commercial ore heaps, which are much larger than encountered with column tests of ore and with pilot heaps, has been recognized111 • Commercial ore heaps using radial stacking conveyors are typically about nine meters high and may be 100 meters or more in lateral dimension. Three oxygen transport mechanisms have been identified and analyzed: ( 1) natural convection, which arises from an increase in buoyancy caused by the temperature rise and gas composition changes associated with the exothermic oxidation of the sulfide minerals within the ore heap, (2) forced air ventilation, using low pressure fans and air distribution pipes within the heap, and (3) diffusion of oxygen in the gas-filled void spaces within the ore heap driven by the oxygen concentration gradient from the surface of the heap to the mineral oxidation loci within it."

Jan 1, 1997

By M. Arenas

A corrosion study of a bonded NdFeB permanent magnet materials alloyed with titanium carbide additions has been undertaken. The materials were produced by rapid solidification by melt spinning. Commercial epoxy was used as a bonding medium. The corrosion results were compared with those of a near stoichometric unalloyed NdFeB. Anodic polarization and potentiostatic techniques in 0.9 M Na2SO4 solutions were used to characterize corrosion behavior. It was found that the addition of 6 a10 Tic resulted in superior corrosion resistance, as indicated by lower corrosion currents and less iron dissolution at fixed potential.

Jan 1, 1997

By K. C. Liddell

"Cu/Ni multilayers exhibiting giant magnetoresistance were deposited from a single electrolyte under stepped potentiostatic control. To enable transport measurements to be made without remounting the multilayer film, we developed a novel method that involved plating on a thin metallic basal layer atop a rigid non-conducting Si substrate. Rotating ring-disk electrode techniques were used to monitor the composition and thickness of individual plated layers. Transmission electron microscopy confirmed that the interfaces between adjacent layers were sharp and that the structure of the layers was uniform throughout the film. Atomic force microscopy images indicated that the film's surface was smooth and free of defects.ELECTRODEPOSITION OF THIN MULTILAYER MAGNETIC MATERIALSI. IntroductionElectrodeposition of compositionally modulated films will in all likelihood continue to be used to produce the read heads for stored magnetic data. However, the next generation of head materials will require both improved sensitivity and reduced film thickness. Certain multi layers consisting of thin alternating ferromagnetic and nonmagnetic layers exhibit giant magneto resistance and consequently are promising candidates for read head applications. We have successfully made multilayer films with giant magnetoresistance that have total thicknesses as low as 25 nm, approximately 120 times thinner than the thinnest similar films reported in the literature. This paper describes early results from our work on electrodeposition and characterization of Cu/Ni multilayers, a model system with enhanced magnetic and mechanical properties, including the GMR effect. The structure and composition of the multilayers were determined using TEM, AFM, and electrochemical methods, and their magnetoresistance was measured by the standard four-probe technique. A novel method developed in this work enabled the transport properties of the ultrathin films to be measured reliably without the need to dissolve the cathode or handle the films. To provide a context for these results, short accounts of other work on giant magnetoresistance and multilayer electrodeposition are also included."

Jan 1, 1997

By Rod Samuels, Rupert Allen, Thomas Harper

"Viceroy Resource Corporation of Vancouver, B.C., has recently developed and brought into production the Brewery Creek Mine, an open-pit heap leach gold mine, located 55km east of Dawson City in Yukon, Canada. Mineable reserves are 15.2 million tonnes of ore grading 1.45 grams/tonne, containing 22 tonnes (707,315 oz) of gold. Ore processing employs the heap leach technology using run-of-mine ore. Highlights of 1996 activity included construction of a 158,000 m2 of leach pad, placing 1.9 million tonnes of ore at a grade of 1. 46 gpt to the leach pad, construction and successful commissioning of the ADR plant, and pouring of the first gold bar on November 15th.Permitting of this mine has drawn significant attention because of the innovated heap leach technology; although this technology has been proven in other jurisdictions, it has not been used at such extreme northern sites where winter temperatures routinely reach -45°C for extended periods.ABSTRACT ONLY"

Jan 1, 1997

By V. L. Stolyarova

The high-temperature Knudsen effusion method was used to study partial pressures of vapour species, activities of components and the Gibbs free energies in the DyF3-Dy2O3 system at the temperature (1357±5) K. Partial pressures of vapour species were obtained by the ion current comparison method, with the DyF3 partial vapour pressure over pure DyF3 as a standard. The equilibrium constant of the gaseous reaction DyF3 + DyOF = Dy2OF4 is evaluated. Thermodynamic data obtained are in a agreement with the available phase diagram of the DyF3-Dy2O3 system. Results of the present study illustrate the negative deviations from the ideal behaviour in the system.

Jan 1, 1997

"The pyrometallurgical method of recycling car batteries suffers from a potential for air pollution violations, which prompts the desire for a viable hydrometallurgicaJ alternative. Several Processes have been proposed, including leach-electrowinning routes using HBF4 and/or HzSiF6 based electrolytes, along with anodes of PbO2 on inert substrates.A study has been carried out to evaluate the proposed systems, with the intention of demonstrating a six month life of an electrolyte-anode combination. The work, which focused on the use of HzSiF6, has indicated that there was no acceptable anode, and has lead to the development of a technique to produce smooth, glassy, adherent coatings on graphite, and to the development of an anode composed of a series of copper cored graphite rods.The paper will present results on leaching and electrowinning experiments, as well as the description of a flowsheet for a pilot plant that will be used to produce one tone per day of refined lead from spent battery paste."

Jan 1, 1997

By M. C. Ruiz

The leaching behavior of chalcopyrite concentrate in acidic CuC12-NaCI-O2 solutions was investigated. Experiments were conducted under continuos flow of oxygen at atmospheric pressures. The results indicated that among the variables temperature has the largest influence on the dissolution of chalcopyrite in this medium, and high copper extraction can only be obtained at temperatures near the boiling point of the solution. It was also found that the stirring speed did not influence appreciably the dissolution of chalcopyrite. An increase in the oxygen flow rate up to 0.1 1/min increased the copper extraction. The total chloride concentration affects the dissolution of chalcopyrite up to about 4 M. Copper extraction of 93 % was obtained in leaching chalcopyrite of size fraction -400 # Tyler at 105 OC in 2 hours.

Jan 1, 1997

By A. G. Jackson, Rand R. Biggers, John D. Busbee, Iman Maartense, David P. Lubbers, David C. Liptak

"This paper describes the application of Raman Spectroscopy for characterizing superconducting YBCO thin film parameters. Attenuation of the substrate Raman spectrum as a function of material deposited is established. Also a correlation between film quality and Raman spectrum is explored. The identification and discrimination of superconducting and non-superconducting phases of YBCO is presented. The critical temperature (Tc) of a film as a function of its oxygen content is also established using Raman peak ratios. These results provide significant implications toward the use of Raman Spectroscopy for in situ monitoring and control of the PLD process. Film quality can be controlled via optimization of film oxygen content and reduction of improper YBCO phases. Film thickness can be controlled by monitoring the response of the substrate material. Also the PLD process can be studied and modeled using this powerful observation tool.IntroductionSuperconductors are materials that possess unique characteristics when cooled to sufficiently low temperatures. Below a material's critical temperature (Tc) it exhibits zero resistance to current flow. One such material, yttrium barium copper oxide (YBCO) has a critical temperature of approximately 92° K. Due to its high critical temperature YBCO is being aggressively researched for many possible applications, because of high current carrying capability and strong pinning of flux lines.YBCO in the 123 form is a ceramic material that was discovered in February, 1987. Its unit cell structure is shown in Figure 1 [ 1,2]."

Jan 1, 1997

By B. Q. Li, S. P. Song

"Numerical models are developed to represent complex electromagnetic, free surface deformation and fluid flow phenomena in floating zone refining processes with radio frequency inductive heating. The computational methodology is based on the coupled finite/boundary element method for the electromagnetic field distribution and the Galerkin finite element method for magnetically driven fluid flow and free surface profiles of the molten zone. With the models, the complex transport and free surface phenomena in a floating zone system can be studied as a function of various operating conditions including applied current, frequency, inductor position and shape, surface tension, floating zone diameter and height. Results show that the equilibrium shape is sensitive to the height of the molten zone and that the free surface shapes can have a significant effect on the melt flow in the molten zone. Our extensive simulations also suggest that to ensure accurate results, the same mesh should be used, whenever possible, for both the electromagnetic forces and fluid flow calculations.1. IntroductionThe floating zone processes have been widely used in the materials industry to grow ultra-pure rare earth metal or semiconductor single crystals for sensor or electronic applications that have a tough demand on purity. Developed based on the principle of magnetic melting/levitation, the processes possess a main advantage that the molten zone is supported in air by the electromagnetic forces generated by the coil (see Figure 1), and therefore is free from contamination from a container. Consequently, the final products made from the floating zone processes have higher inherent purity than those by other techniques [1-4].Complex physical phenomena occur in the floating zone processing of materials. These include free surface deformation, magnetically-driven melt flow, which may be turbulent or mildly turbulent [5] depending on the applied conditions, and solidification. Thermal stresses also develop in the single crystals, which are affected by the flow and temperature field and which can have direct implications to qualities of single crystals [6]. An understanding of the fundamentals governing these physical phenomena can be of critical value in elucidating the physics that controls the properties of the metal or semiconductor crystals being produced, thereby providing a rational basis for process improvement and quality control."

Jan 1, 1997

By Juan B. Cabezas

"The favorable characteristics and workability of plastics as a replacement of wood, lead, stainless steel, asphalt and other materials are described. Various types of plastic have proven to be the most favorable choice for handling a variety of acidic, alkaline and organic solutions, as well as pulps, chemical wastes, slurries or tailings for impoundments. The material origin of various plastics, methods of manufacturing and specifications applied to leaching solutions are discussed, including availability and costs. Examples of select plastics are considered for use as alternatives of other materials under severe environmental requirements.IntroductionHydrometallurgical processes applied to gold recovery, as well as other metals, require the use of strong solutions of alkaline, acidic or organic nature, and may also include a variety of materials with extraneous characteristics and complications for handling in storage.The technology of leaching has been in use for more than 100 years, but the applications of leaching processes in metallurgy have become more commonly used in the last 15 years. Suitable materials for the construction of containers, launders, piping, and various accessories, to be used in the handling of leach solutions or slurries, have become a serious problem. Various metals such as brass, lead, stainless steel, etc., and non metallics including wood, clays, glass, rubber, ooncrete, tars or miscellaneous compounds have been tried in the past with serious limitations in workability and resistance to wear and corrosion. For example, the use of metallic, wooden or glass piping systems would require extraordinary shop maintenance to keep such systems in operation"

Jan 1, 1997