Search Documents

By Lloyd Robert Nelson

The historical progression in installed electric furnace smelting capacity of some 1650 calcium, chromium, manganese, nickel and silicon ferro-alloys furnaces is reviewed. Key increases in the inherent installed electrical capacity, often achieved through uprating furnaces, are identified. Possible factors facilitating such advances are explored, including: specific process engineering and pyrometallurgical enhancements (e.g., improved control over the consistency, size and chemical form of raw materials, extents of preheating and pre-reduction delivered into the furnace; and patterns of feed distribution); furnace electrical configuration (AC or DC; immersed, submerged-, shielded- or open-arc); form of electrode (graphite, self-baking or composite); furnace configuration (circular or rectangular; closed or open and 1-, 3- or 6- electrodes); better engineering and equipment designs (e.g., high-intensity cooling) and state of furnace electrical and metallurgical control systems. A view is presented on the prevailing state of evolution of the Mega-scale in ferro-alloy smelting and opportunities for still further improvements.

Jan 1, 2014

By T. Plikas, L. H. Gunnewiek, L. Oshinowo

"Electric furnace smelting is one of the principal unit operations for ferroalloy production, and increased process intensity, improved availability, minimal maintenance and a longer campaign life are common objectives for electric furnace operation in order to obtain favourable economics of production. Furnace designers have continued to develop innovative solutions, e.g., furnace cooling systems, that have allowed these objectives to be realised and CFD modelling plays a key role in the design process. Enhanced understanding of the energy transfer process in the furnace and the ability to develop, evaluate and optimize components of the crucible design to match process requirements are the key motivators for modelling.This paper provides an overview of recent applications of CFD to the design of electric furnaces. The aim is to illustrate what can be done, and identify areas where further work is needed in this field. Examples include furnace bath simulation, crucible cooling system design, taphole design, baking of Soderberg electrodes, off-gas systems, and fume control and building ventilation. It is argued that the trend is for numerical models to become more encompassing while at the same time more accessible, and therefore further improvements in furnace design will be realised with continued and well validated modelling efforts.IntroductionOne of the main processing steps in ferroalloy production is the smelting of ore in electric furnaces. The three-electrode, AC submerged arc furnace is most prevalent method for smelting in the industry, with shielded-arc and DC plasma arc furnaces achieving limited application (1,2). Commercial furnaces range in size from a few megawatts to more than eighty megawatts of supplied power, and operate with the objective of maximising the return on capital invested. Maximising productivity and energy efficiency are two pathways to achieving this objective, through process intensification, increased availability, minimal maintenance, and increased campaign life for the furnace and associated equipment. Concurrently, the need to reduce the environmental impact of metal production by controlling the emission of particulate emissions, greenhouse gases, and other harmful by-products must also be met."

Jan 1, 2004

Numerical simulation of the fluid flow and heat transfer has been carried out for a waste-heat boiler in an Outokumpu type copper flash smelter. In this boiler, SO2-containing off-gas flows into the waste-heat boiler radiation section at about 1350°C. A fraction of cooler off-gas from the electrostatic precipitator at about 200°C was recirculated into the radiation section, and a small amount of ambient air was leaked into the boiler from the bottom. The computational results show that the flow is strongly recirculating and distinctly three dimensional in most of the boiler, particularly in the radiation section. The hot off-gas cooled down rapidly after entering the radiation section due to radiation. The predicted flow pattern and temperature distribution were in a good agreement with laboratory models and industrial measurements.

Jan 1, 1995

By Arthur E. Morris

Fifty years ago when Professor Yazawa began his career, the field of process simulation and modeling was in its infancy. Since then, tremendous progress has been made in our ability to model metal production flowsheets from mine to refined metal. This progress has come about by parallel developments in basic understanding of process chemistry and in computational techniques, This paper will review the progress made in process understanding and modeling in lead, zinc, and copper metallurgy from its inception to the present, and the role of Professor Yazawa's work in furthering this progress. Specific examples will be given for the sintering of lead concentrates, slag fuming, zinc concentrate roasting, flash smelting of copper, and pyro-extraction of zinc. Factors limiting further progress will be described.

Jan 1, 2003

A comprehensive numerical capability for the analysis of Thermal Spray (TS) systems consisting of a three-dimensional compressible, turbulent flow Navier-Stokes model and a multi-phase particle flow model in Lagrangian formulation, was developed. This capability is validated for a set of flow conditions typical for TS. The developed methodology is used for analysis of the JP-5000 TS gun gas and coating powder flow conditions. Modeling and analysis of particle/turbulent eddies interaction is performed. Details of gas flow field, particle temperature, and particle velocity histories, and particle temperature, velocity profiles in the system are presented. For the validation of numerical analysis, the computed results are compared with available experimental measurements. The flow phenomena for different flow parameters are analyzed and explained as the results of gas dynamics and heat and momentum transfer between the gas and particle phases. This methodology can be used for process control and reliability improvement, and has the potential to significantly improve TS gun performance through control of its parameters.

Jan 1, 1996

By Oszkar Bíró, Peter Mittag, Bernhard Aigner, Stefan Pirkeri, Philipp Glttleri

"This paper considers CFD modeling of processing and melting of small metallic particles by means of electrical heating. The particles fall continuously onto a liquid metal bath which is heated by an electric arc. After melting of the particles liquid metal is tapped.The charging behavior of the particles in the supply unit as well as in the reactor freeboard is studied by means of Euler-Euler granular simulations. The flow situation in the metal bath due to gas injection and magnetic fields is calculated by combining Navier-Stokes and Maxwell solvers. The macroscopic melting process occurring during the continuous charging of the particles is studied by kinetic laws for melting reactions. The temperature field is evaluated by balancing heat sources due to Joule's heating and heat losses due to latent heat of melting as well as convection and radiation.As a result of these simulations the fully three-dimensional flow fields of particles and gas in the atmosphere is obtained. Furthermore the flow field as well as the magnetic field in the metal bath can be studied. As a main result the three-dimensional concentration field of the still unsolved particles in the liquid metal can be evaluated.IntroductionIn this paper a metallurgical process for melting small iron particles is investigated by means of CFD-simulations. In a first process step the preheated and already mostly reduced iron particles fall continuously into the reactor through a vertical tube mounted at the lid of the furnace. In a second step the particles are melted in the liquid metal bath. Meanwhile the melt is heated by electric arcs to provide the heat needed for melting the incoming particles.In Figure I a sketch of the geometry setup considered in this paper is provided. The particles fall from a height of approximately 12 meters onto the bath surface in the center of the furnace. The melt is heated by electric arcs that are placed symmetrically around the center axis."

Jan 1, 2001

By Arthur E. Morris

Fifty years ago when Professor Yazawa began his career, the field of process simulation and modeling was in its infancy. Since then, tremendous progress has been made in our ability to model metal production flowsheets from mine to refined metal. This progress has come about by parallel developments in basic understanding of process chemistry and in computational techniques. This paper will review the progress made in process understanding and modeling in lead, zinc, and copper metallurgy from its inception to the present, and the role of Professor Yazawa's work in furthering this progress. Specific examples wi1\ be given for the sintering of lead concentrates, slag fuming, zinc concentrate roasting, flash smelting of copper, and pyro-extraction of zinc. Factors limiting further progress will be described.

Jan 1, 2003

By Ragnhild E. Aune, Mark William Kennedy, Shahid Akhtar, Jon Arne Bakken

"To determine the heating rate of billets using ‘short coils’, an appropriate correction factor must be applied to the theoretical relationship. In 1945, Vaughan and Williamson published a semi-empirically modified Nagaoka coefficient applicable for moderate frequency induction heating processes (10 kHz). Recently it was demonstrated that the method of Vaughan and Williamson gives <10% error in the estimated power when heating aluminum billets at 50 Hz.In the present study, experiments have been conducted on aluminum billets in order to verify an empirical frequency corrected ‘short coil’ equation. Measurements of electrical conductivity (<± 0.5%), current (± 1%), heat (± 1-3%), and magnetic flux density (± 1-2%) have been performed. The results are compared with 1D analytical calculations, and 2D axial symmetric FEM modeling using COMSOL 4.2®. The frequency corrected equation has proven to provide accurate predictions of power (<4% error) within the frequency range 50 Hz to 500 kHz.IntroductionInduction heating is commonly applied to the re-heating of billets before forging or extrusion processes. The resistive heating produced by eddy currents in the solid or semi-solid work piece during this procedure, is driven by the time varying magnetic flux density in the air-gap between the work piece and the coil. The flux in the air-gap is created by the current flowing in the induction coil, i.e. the magneto-motive force. In Figure 1 it can be seen that the currents present in the work piece are concentrated in the outer ‘shell’, or the first electromagnetic penetration depth (dw), and flow in a direction which opposes the magnetic field produced by the induction coil."

Jan 1, 2012

By J. W. Evans

Mathematical modeling has now become a standard technique in the development of new technology and the improvement of existing technology in the processing industries. Physical modeling has a longer history but a smaller following at present. The paper reviews some examples of the application of both types of modeling in non-ferrous metal extraction, particularly within the copper and aluminum industries. The objective is to show that well founded models can lead to results that have practical consequence in scaleup, design and operation.

Jan 1, 1993

By R. M. Sweetin

Detailed descriptions by operating area of the Kidd copper smelter are presented, together with accounts of complement staffing, training, and preparation activities for smelter start-up in June 1981. Concentrate tonnages smelted in the first twelve months of operation were constrained by the capacity of the furnace off-gas system. However, modifications designed and introduced over that period, plus sustained efforts by operations and maintenance personnel have resulted in stepwise improvements in smelter performance.. Consistent operation at design feed rates has been well demonstrated over the third and fourth smelter campaigns and efforts continue on further improving the continuous smelter on-line times and increasing campaign life. In November 1982., following a seventeen month preproduction period, the Kidd smelter attained full operating status.

Jan 1, 1983

By Gerald M. Rich

Magma Copper Company, a subsidiary of Newmont Mining Corporation, has initiated many changes in the continuous casting of 5/16 inch diameter copper rod since startup of the San Manuel rod plant in early 1972. With rod production at forty percent over design capacity, many production records have been established including a record cast of 761 tons of salable rod in a twenty-four hour period. The most challenging and rewarding introduction was the continued utilization of an alloyed copper casting wheel in lieu of the conventional steel wheel. With proper cooling and careful control of the mold release agents. as much as 58.000 tons of copper were cast on a single copper wheel. Other advantages are: 1) Fifteen percent increase in available casting time 2) Reject rod from steel inclusions was reduced by nearly one-hundred percent 3) Wheel cost was decreased by ninety-one percent 4) Natural gas consumption dropped approximately fifteen percent 5) Large increase in refractory component life 6) Reduction of manhours/ton. Many other modifications have contributed to excellent rod quality and high operating efficiency. A two-piece launder was replaced with a single castable launder which reduced oxygen pickup and provided better slag removal. Modifications to the bar preparation unit, pickling system, and coiler resulted in considerably higher milling efficiency.

Jan 1, 1976

By Kenneth L. Driggs

The Environmental Protection Agency&apos;s Clean Air Act? of 1970 provided the driving force for the current Magma Smelter configuration. The historical and technical perspectives of those process developments are reviewed?. Innovations in procedures and equipment have allowed compliance with the requirements of the regulating authorities?. The wet scrubbing of converter gasses and the monitoring of converter operations by a controlling foreman are two of the major contributors? to these successes. The Clean Air Act Amendments of 1990 have posed many new concerns? for all U.S. industry, including the few (seven) primary copper smelters remaining. Future concerns include tightening the sulfur dioxide ambient ?Standard from the current three-hour averaging period to one hour.

Jan 1, 1992

By E. Oshima

In May 1991, a New Mitsubishi Continuous Copper Smelter Line started operation at Naoshima. Recently, it has been continuing steady operation and one and a half year campaign life has been achieved. In 1996, new records of on line time, the amount of copper concentrate treated and copper anode production were achieved. 1t proves the superiority of the process with respect to pollution control, energy efficiency, flexibility and easiness of the operation and over all economy including off gas handling cost. Furthermore, .plans are underway to prolong the campaign life for two years and to improve the process efficiency. This paper describes recent operation, improvements, and a future capability study.

Jan 1, 1998

By G. Van Weert

Refractory gold ores and auriferous concentrates containing silver tend to form refractory silver jarosites during pressure oxidation. Earlier work with pure Ag2S has shown that the addition of iodine species to the autoclave feed yields cyanide soluble iodargyrite (Agl) instead. Near complete silver extractions from the autoclave product were obtained at a I-/Ag+ ratio of 5 or more. This paper reports on the pressure oxidation and cyanide leaching of two industrial refractory (arseno) pyritic silver-bearing concentrates: 1. from Peru (sulphosalts) and 2. from the USA (pyrite, with acanthite occlusions). While using a I-/Ag+ mol ratio of only 1 in the feed, it has been possible to obtain 98 and 97% Ag extraction from the two autoclave products by cyanide leaching, respectively. This compares to 11 and 54% Ag extraction from the as-received concentrates and 4 and 15% Ag extraction, respectively, after pressure oxidation without KI present. The results of the testwork are discussed in terms of concentrate mineralogy and pressure oxidation conditions.

Jan 1, 1994

By Kenneth L. Driggs

The Environmental Protection Agency&apos;s Clean Air Act of .1970 provided the driving force for the current Magma Smelter configuration. The historical and technical perspectives of those process developments are reviewed. Innovations in procedures and equipment have allowed compliance with the requirements of the regulating authorities. The wet scrubbing of converter gasses and the monitoring of converter operations by a controlling foreman are two of the major contributors to these successes. The Clean Air Act Amendments of 1990 have posed many new concerns for all U.S. industry, including the few (seven) primary copper smelters remaining. Future concerns include tightening the sulfur dioxide ambient standard from the current three-hour averaging period to one hour"

Jan 1, 1992

By Binxu Zhaug, Mark Jolly, Xiaojun Dai

"In conventional investment casting process of aluminium alloys for the application of the aerospace industry, to assure the quality of the final casting, usually the foundry uses large runner system which results in low yield, high energy consumption and high GHGs emission. In one case of this investigation, the yield is between 5 ~ 10% which means that the current casting process wastes large amount of energy and generates lots of scraps. By applying a new casting method, the bulky runner system and the melting/holding time are significantly reduced, the quality of the casting is improved, and in the meantime the related energy consumption and GHGs emission are significantly decreased. In the investigation, the energy efficiencies and GHGs emission between the current and traditional processes are calculated and compared.1. IntroductionAs one of the conventional casting process, Investment Casting Process (ICP) and its applications can be traced to thousand years ago [l]. In current casting industry, ICP still plays an important role in the production of small and precious castings with high quality requirements in automobile and aerospace industries. Both casting quality and manufacturing costs which mainly consist of energy costs have crucial effects on the competitiveness of castings in the market. In the production of aluminium alloy castings using ICP, the energy cost and energy efficiency of a casting facility depend mainly on the efficiency of its melting and heat treating performance. In association with the two performances, more than 60 % of the total process energy costs are symbolised in a typical casting facility [2]. Additionally, in conventional ICP of aluminium alloys for the application of the aerospace, to assure the quality of the final casting, typically the foundry uses huge runner system including big risers/feeders which cause low yield, creates lots of scraps and generates high energy consumption. Consequently, there are huge opportunities for casting industry to choose the best practices for potential energy saving. Furthermore, the reasons such as the stringent limitation of environmental legislation in Europe and the pressure of the rising energy price force the casting industry to reduce the energy consumption and greenhouse gases (GHGs) em1ss10n."

Jan 1, 2012

By Yong Hack Lee

Nonferrous smelting processes have been through a rapid transformation since the beginning of 1980. The copper smelting technology has changed from the conventional Blast Furnace process to the Flash Smelting and MIB process. In the field of lead smelting, the technology has changed from the Blast Furnace Smelting to the Direct Smelting such as QSL and KIVCET. In 1992, Onsan Refinery successfully commissioned Direct Smelting QSL technology for lead. The QSL could produce more than 160,000 ton per year of lead bullion from lead concentrate and various residues. Moreover, since the year 2000, the TSL (Top Submerged Lance) Technology utilizing the same Direct Smelting process has been successfully commissioned to treat lead concentrate as well as lead sulfate residue produced from a hydrometallurgical zinc plant. This paper presents and compares the energy flows of lead smelting processes such as a conventional process and the Direct Smelting Processes plotted on the Pb-O-S phase diagram. The oxygen potential diagram suggests how to control the oxygen potential in the fum ace. Also, it describes the recent operational experience in the TSL plant of Onsan Refinery with necessary mass balance of key elements.

Jan 1, 2003

By C. J. Newman

Production levels at the Kidd Creek copper operation increased during the 1980&apos;s by expansion of both the smelter and refinery and by major modifications to equipment which was causing bottlenecks. As a result, there was a significant reduction in the unit cost, some manpower reductions and hence a significant increase in productivity. In the last two or three years, there have been no major expansion projects leading to unit cost reductions and yet these have still been attained. This has been achieved by the development and implementation of various techniques designed to maximize the inherent potential of the operators and maintenance employees. This paper will initially describe the operation but will then place emphasis on employee involvement through such methods as idea awards, incentive schemes, loss control and continuous improvement programs. Organizational changes are discussed, particularly with reference to changes from the traditional operator role to one which encompasses maintenance skills and to cross-training of maintenance employees into multi-discipline fields. The effect of these changes are discussed by a review of the salient plant parameters of safety, production levels, cost and quality.

Jan 1, 1993

By Rainer Schmid-Fetzer

"Isothermal solidification can be used to form strong bonds at low temperature which remain solid at much higher temperatures. The exploitation of this principally known technique for new high temperature processing steps and applications in electronic assemblies is the aim of this study. Three basically different variants of this bonding process are given. A comprehensive metallurgical screening is performed and the feasibility of binary material systems is given on a quantitative scale. Very attractive systems are spotted that have never been studied before. Detailed examples for the realization of bonding with complex ternary and multilayer systems are given. A highly innovative example is the chip stack or wafer to wafer bonding of unmetallized Si or SiC at 250°C. The proposed bond remains stable above the melting point of Si and enables entirely new semiconductor manufacturing steps. An improved die bonding process was proposed and verified experimentally.1. IntroductionIsothermal solidification can be applied to form strong bonds at relatively low temperature which remain solid at higher temperatures. The general principle of this type of joining processes is illustrated in Fig. 1. An interlayer of a low melting component, Lo, is provided as a foil or a thin film coating between the high melting joint components, Hi. The assembly is heated under moderate pressure to the bonding temperature, T 8 , and a liquid filler forms, either because the melting point of Lo is exceeded or due to a eutectic reaction between Lo and Hi. This molten filler initiates a rapid interdiffusion or reaction diffusion between Lo and Hi and the subsequent approach to an equilibrium state results in isothermal solidification. The solid phases formed at T 8 in the joint region exhibit a remelt temperature above T8 •"

Jan 1, 1996

By Art Johnston

Gas handling at Magma Copper company&apos;s, San Manuel smelter receives process gas from a flash .smelting furnace and four copper converters. The major gas handling equip11lent consists of four electrostatic precipitators and a sulfuric acid plant. Process ,vessels in gas handling are, typically confined, spaces. Lethal gases, mechanical and chemical hazards, and the difficulty of rescue, should an accident occur, makes this area a must in the safety plan. The presence&apos;: of hazardous chemicals and explosive gases in process&apos; vessels and piping are of major concern when repairs&apos; are required. Proper job procedures are critical to prevent injury during repairs. This includes plant employees and contractors who are likely to be unfamiliar with the hazards ,involved. The safe operation of a gas handling operation must include the functions of operations employees on a daily basis. This includes a safe working environment and involvement of all employees in the safety program. If an injury does occur quick medical response is critical to prevent serious injury. Medical responders must be adequately trained and prepared to treat the injured person without becoming victims&apos; themselves. The methods used at Magma Copper Company to deal with these safety problems are the focus of this presentation.

Jan 1, 1992