Search Documents

By Wayne Bell, Xiaodi Huang, Matthew Andriese, Jiann-Yang Hwang, Zhiwei Peng

"The equations for determining microwave field attenuation length and half-power depth in magnetic materials were derived from Maxwell’s equations. The microwave field attenuation length and the half-power depth for a magnetite concentrate were calculated and the temperature dependence of them was determined. It is demonstrated the microwave field attenuation length and the half-power depth highly depend on temperature and decrease with increasing temperature up to 900 °C. The variations of field attenuation length and the half-power depth with temperature indicate the microwave power attenuates much faster than the field strength in materials. The evaluations of field attenuation length and microwave half-power depth can be used to characterize the microwave dissipation behaviors in the sample and optimize the dimensions of the material in microwave heating.IntroductionMicrowave has been applied in materials processing for its distinguished advantages including rapid heat transfer, volumetric and selective heating [1,2]. However, most research work involving microwave heating are confined to non-magnetic materials (e.g. ceramics), with limited attention paid to the heating of mixed property materials (e.g. magnetite and other ferrites) under microwave irradiation [3-5]. Since many magnetic materials exhibit good and even better microwave absorption capability than non-magnetic counterparts, it is quite necessary and deserved to take advantage of this property and then improve the heating efficiency. To achieve this aim, further understanding on the microwave heating mechanism, especially the microwave propagation/dissipation behaviors in magnetic materials is required.The dissipation behavior of microwave in materials has been identified as one of the key factors that affect the efficiency of heating under microwave irradiation and this behavior can be characterized by several parameters. Apart from traditional penetration depth (TEM power penetration depth, Dp = 1/(2*a), where a is the TEM field attenuation factor), two other parameters, field attenuation length (Df) and half-power depth (Dh), are also applied to indicate the microwave dissipation in materials [6].The accurate determination of such parameters can help in optimizing the dimensions of the load in a microwave furnace, producing more uniform heating under microwave irradiation and avoiding thermal runaway."

Jan 1, 2011

By Carlos Antonio da Silva

Steel refining reactors based on chemical heating are being used as an alternative to ladle furnaces, They show a high degree of flexibility in respect to heating rate in addition to carrying out refining reactions such as de-S, inclusion removal, alloying etc. IR-UT and CAS-OB are examples of such reactors. Their performance is dependent upon geometrical characteristics as well as operational conditions which determine the flow field inside the vessel. A physical model of the IR-UT process of the Companhia Siderúrgica de Tubarão, steel plant located in Serra, Espirito Santo, Brazil, was developed to assess the features of the flow field and its influence on the metallurgical behavior. Results of the physical model were used to optimize the process parameters in the industrial unit.

Jan 1, 2003

By A. F. Giamei, F. Landis, M. O. Duffy, R. J. Mador

"The directional solidification of complex advanced gas turbine airfoils must be carried out without the nucleation of undesirable grains and with minimal shrinkage. Such problems are typically eliminated by using a number of mold design and process iterations. A more efficient approach is envisioned where a solidification model is generated and utilized to accelerate process development. Towards this end, the directional solidification (DS) of simple geometrical shapes in a crystal grower apparatus has been simulated with MARC finite element nonlinear thermal analyses.The finite element models of cylindrical (2D) and rectangular (3D) cross-section bars in the DS environment are presented. Temperature dependent properties, the impact of latent heat of fusion and a time-dependent radiation boundary condition constitute the more salient features of the MARC models. Solidification zone thermal behavior is predicted during the withdrawal transient for the specific case of nickel based superalloys grown in ceramic shell molds. Comparisons of analytical results with experiments demonstrate notable prediction accuracy. INTRODUCTIONSingle crystal and uni-directional crystal turbine blades require tightly controlled conditions if metallurgically and mechanically acceptable parts are to be produced. Gated blade geometry and process parameters must be precisely determined if incorrect grain structure, orientation and shrinkage are to be avoided. Since purely experimental development programs designed to evaluate these parameters can be excessively costly and time-consuming, an effort combining engineering analysis and verification by experiment has been initiated at Pratt & Whitney. Comparison of analytical predictions and measured data for geometries simpler than a turbine blade, namely cylindrical and rectangular bars, comprised the initial stage of this effort. Subsequent tasks involve modeling geometries of increasing complexity and ultimately the simulation of the directional solidification of the turbine blade, shown schematically in Figure 1. This paper summarizes the results of the initial stage of the effort."

Jan 1, 1986

By Carlos Antonio da Silva

Steel refining reactors based on chemical heating are being used as an alternative to ladle furnaces. They show a high degree of flexibility in respect to heating rate in addition to carrying out refining reactions such as de-S, inclusion removal, alloying etc. IR-UT and CAS-DB are examples of such reactors. Their performance is dependent upon geometrical characteristics as well as operational conditions which determine the flow field inside the vessel. A physical model of the IR-UT process of the Companhia Siderurgica de Tubarao, steel plant located in Serra, Espirito Santo, Brazil, was developed to assess the features of the flow field and its influence on the metallurgical behavior. Results of the physical model were used to optimize the process parameters in the industrial unit.

Jan 1, 2003

By W. G. Davenport

The remainder of this book develops and uses mass and heat balances to describe steady"state flash smelting. Its objectives are to: a) describe the many ways a flash furnace operator can produce specified products, e,g. 65% eu matte, 35% SiOz slag, 1500 K (b) determine the oxygen, air, flux and hydrocarbon fuel requirements of each method (c) show how the flash furnace can be controlled to give specified products with varying feed compositions (d) suggest how the flash furnace operator can maximize profitability while producing specified products. This chapter develops the basiC heat and mass balance equations of steady-state ?flash smelting. It then adapts the equations to industrial feed materials .and products. Lastly it determines the amounts of oxygen and flux needed to produce molten matte and 35% SiOz slag from chalcopyrite concentrate in an Inco oxygen flash furnace,

Jan 1, 2001

By L. Katgerman, R. Van Toi, H. E. A. Van den Akker

"Mould filling simulations are powerful tools for optimizing the characteristics of castings. The robustness of calculational methods for mould filling simulations is generally tested in simple geometries. While a vertical plate has been used often for validation studies, this paper aims at mould filling simulations of a horizontal thin wall casting. Such castings exhibit a strong interaction between heat transfer (solidification), surface tension and gravitational force.The results are presented of a study to validate numerical simulations of mould filling phenomena in a thin wall horizontal casting. Solidification during mould filling is studied computationally. Velocities are measured using Particle Image Velocimetry.INTRODUCTIONIn foundry practice Computational Fluid Dynamics (CFD) is being considered a promising tool to arrive at a better understanding of casting defects introduced during the mould filling period of a casting. The use of CFD is believed to be advantageous in predicting possible defect locations, pouring times, and the lowest possible casting temperature without the risk of cold shuts. In addition, CFD may be used to optimize pouring system geometries [1,2]. As opposed to experimental studies in, e.g., cold water models, CFD allows for the flexible modification of the casting geometry and the pouring system, and for the inclusion of physical effects such as solidification and heat transfer. Thus, a proper use of CFD may lead to a reduction of the casting rejection rate without expensive trial-and-error procedures, and to a decrease of production costs in foundries. Mould filling simulations take a special place in CFD, because a free surface tracking algorithm is required. Over the past decade methods, MAC [3] and SOLAVOF [4], have been extended to 3-D. The robustness of computational methods for mould filling simulations is generally tested in simple geometries [5,6]. While a vertical plate has been used often for validation studies, this paper concentrates at mould filling simulations of a horizontal thin wall casting. Thin wall horizontal castings exhibit a strong interaction between heat transfer (solidification), surfaces tension and gravitational force. The gravitational force in this setting is orthogonal to the plane of flow and has therefore no influence on the shape of the free surface in the plane of flow. Mould filling numerical methods and algorithms have been recently reviewed by Chen et al.[7]."

Jan 1, 1999

By S. Z. El-Tawil, K. A. El-Barawy, M. B. Morsi, M. M. Nasr, Z. I. Zaki

"Tue sulphatization of zinc concentrate produced from heated zinc concentrate of Um Ghieg area, eastern desert by ammonium sulphate as sulphatizing agent is carried out at different conditions to achieve the appreciable formation of soluble sulphates. The maximum zinc recovery as soluble sulphate equfils to 95% upon using 1.5 stoichiometry ammonium sulphate at 600 °C for one hour. Tue obtained leached zinc sulphate solution is subjected· to purification process to prepare high pure zinc metal and zmc compounds such as pure zinc sulphate, zinc caibonate and zinc oxide. The products obtained are analyzed chemically and identified by X-ray analysisTue mechanism and kinetics of the sulphatization process of zinc concentrate are considered where the activation energy is calculated and equals to 33.3 K.J.mol""1 A process flowsheet for the overall sulphatization process of zinc concentrate by ammonium sulphate is proposed.IntroductionConsiderable reserves of zinc ores are present in Um Ghieg area eastern desert, Egypt. The possibility of extraction zinc from these ores and preparing its valuable compounds by choosing a more feasible technology become of vital importance. An attention is focused on the sulphatizing roasting processes (1-9) to achieve the appreciable formation of soluble sulphates. Previous publications are reported in our division by El. Tawil and others (10-16) using ammonium sulphate as sulphatizing agent for the successful treatment of nonferrous bearing materials.Therefore, the present work aims to study the different factors affecting the sulphatizing roasting process of local zinc coocentrate by anunonium sulphate to extract completely zinc and preparing its main compounds. Tue mechanism and kinetics of the different chemical reactloos that 1ake place in the process are considered."

Jan 1, 2000

By Youze Xu

The effect of oxalic acid, acetic acid, citric acid and EDTA on extraction of Cr (?) in soils contaminated by chromium- containing slag was investigated using a batch of incubation experiment. The results show that the pH value decreases more obvious with the increase of the amount of organic acid. The amount of Cr (?) extracted increases with increasing the amount of organic acid. When the ratio of organic acids to total Cr was 5:1, citric acid revealed the highest extraction effectiveness, followed by EDTA, oxalic acid and acetic acid, respectively. The amounts of Cr(?) extracted by citric acid, EDTA, oxalic acid and acetic acid increased by 439%, 244%, 215% and 162%.

Jan 1, 2009

By Kampe. S. L., Baker. Andrew H., Tony Zahrah

"Experimental heats of reaction for the formation of several Al3Ti + TiB2 intermetallic composite formulations have been determined utilizing bomb calorimetry. To overcome the kinetic constraints and achieve ignition in these formulations, a boron (B)/potassium nitrate (KNO3) initiation aid was incorporated within the blended reactant compact. The heat contribution from the initiation aid was regressed to provide estimates of the heat of reaction of the nominal formulations. Powder x-ray diffraction was utilized to identify the products of the reaction and discern any differences between the predicted equilibrium products of the formulation and the actual products.IntroductionReaction synthesis is a technique for the creation of ceramics, intermetallics, and in-situ composite materials [1]. Reaction synthesis is defined by its self, propagating mechanism, where the energy liberated from a localized reaction within a green powder compact is enough to carry the bulk reaction to completion. Achieving a self, propagating state can be achieved in variations of two primary methods of initiation: uniform volumetric heating and directional propagation [2].Uniform volumetric heating involves subjecting a green compact of the unreacted formulation to uniform heating in a furnace to encourage diffusion to initiate the reaction (Figure 1a) throughout the bulk material. Directional propagation utilizes a point heat source at one section of a green compact of unreacted formulation (Figure 1b). The localized exothermic reaction at one point in the compact then initiates the reaction in the section of the compact adjacent to it and fully propagates throughout the entire compact until completion. Initiation of the localized reaction is generally associated with the melting of the constituent with the lowest melting point, with instantaneous initiation of the reaction usually occurring close to that melting point [1]. This melting point can be high in some systems of interest, such as the titanium (Ti) and boron (B) system in equation 1:"

Jan 1, 2011

By Lifeng Zhang

Printed circuited boards contain considerable quantities of valuable metal, while also containing many environmental pollutants making them unsuitable for landfill. In this study the decomposition of common plastics used in printed circuit boards were studied. Polytetrafluoroethylene (PTFE), polyvinyl chloride (PVC) and polyethylene (PE) were heated in both C02 and argon atmospheres using a thermo-gravimetric furnace (TG) coupled to a mass spectrometer (MS). Soda ash Na2C03 and baking soda NaHC03 were used as reactants. The degradation temperatures and evolved gases are presented for single plastics and mixtures. Mixed plastics are shown to behave as a sum of the individual plastics. The mass loss temperature is the same in CO2 and argon. However, less residue is formed when heated in CO2.

Jan 1, 2008

By Z. Smieszek, W. D?browicz, J. Pawlowski, G. Krawiec, J. Czernecki, J. Por?mbski, S. Gizicki

Rapid development of the automotive industry and motorization has been observed in Poland over the last decade. This phenomenon has increased the amount of used car batteries requiring recycling and has thus posed new challenges for their processing. Orzel Bialy" S.A, is the major secondary lead smelter in Poland. Ibis paper describes the program for smelting technology modernisation and productivity increase through the application of oxy-fuel burners, which has been implemented at "Orzel Bialy'' S.A. The main objective of smelter modernisation, which was to increase the furnace productivity by 20%, has been achieved. This paper outlines the previous and present state of the lead acid battery scrap smelting technology at the "Orzel Bialy" S.A. Specifications of the burners and of oxygen installation are given. Industrial tests with the modernised smelting technology and optimisation of the process parameters are described, and the results obtained are discussed.

Jan 1, 2000

By Milton Manrique

The thermal decomposition of zircon concentrates in a non-transferred arc thermal plasma flow reactor was investigated. The plasma torch was operated using argon-helium and argon-nitrogen mixtures as plasma gases. The effect of power, feed rate and zircon particle size was studied. Products were characterized by XRD, SEM, TEM and chemical analytical techniques. The average size of the product was in the submicron range. Free energy minimization plots were used to predict the behavior of the system under different operating conditions. A kinetic model to describe the different stages of the thermal decomposition process is proposed. The results of this investigation showed a significant segregation process where the zirconia-rich product is collected in the reactor while the silica-rich product is collected in the filter. TEM analysis indicated that silica vapor is condensed on the surface of the zirconia particles.

Jan 1, 1996

By M. Cross

Heap leaching presents a complex physico-chemical process to model and a significant challenge to develop a comprehensive model enabling reliable predictions of heap behavior over the long term. A computational modeling framework is described for the analysis of multi-phase flows in reactive porous media suitable for tracking metals recovery, for example, in heap leaching and environmental recovery processes. This modeling framework employs appropriately formulated, parameterized, and solution procedures to capture: 1) liquid and gas flow through heterogeneous porous media subject to variably saturated flow conditions, 2) the complex and dynamically changing nature of the porous media structure, 3) the transport of reactants and products of reaction, 4) the simultaneous mass and heat transfer, and 5) the role of bacteria as a catalyst for reactions. A second class of challenges to accurately model heap processes is to identify and then capture all the process data to characterize the reactivity of particular ores, the mine planning for the construction of the heap, leach schedules, meteorological data, etc. The objective of this paper is to outline these challenges and to describe a modeling framework that can cope with arbitrarily complex geometries and provide tools for rapid and accurate process assessment.

Jan 1, 2006

By Eiichi Kuzuno, Atsushi Shibayama, Toyohisa Fujita, Kazuo Koike, Toshio Miyazaki, Hitoshi Masuda

"A solid sulfur is more useful to recover and store than a sulfuric acid as a by-product in the zinc hydrometallurgy. In this experiment a zin concentrate (sphalerite) was leached with ferric sulfate at about 373 K for 3 to 6 hours. Zinc was leached more than 95%. After a solid-liquid separation, the leached residue contained solid sulfur was obtained. The particles in the residue were dispersed by lignin and the solid sulfur of approximately 85% was recovered as float product by a flotation with frother in the pH 4. The dried float product was heated at 413K for 2 hours. The pure solid sulfur was recovered. On the other hand in the leached liquid a zinc oxide was ·added and ferrous .iron was oxidized to ferric iron by blowing oxygen. This ferric iron was returned to the zinc leached process after solid-liquid separation.IntroductionZinc concentrate is usually roasted as pretreatment in zinc hydrometallurgy and the produced S02 is changed to sulfuric acid. However, recently in Japan the utilization of sulfuric acid has been limited and it is more costly to store. Instead of producing sulfutic acid the solid sulfur recovery has been examined by direct leaching of zinc_ concentrate in this experiment.In the direct leaching, several kinds of effects have been studied for leaching of sphalerite in ferric sulfate solution. The addition of lignine siilfonate1 • 2) and fine· grinding3) increases the · speed arid leaching fraction of sphalerite. The leaching ratio depends on impurities in sphalerite ores4 • 5). Here, the zinc concentrate is leached ferric sulfate solution under atmospheric pressure at 373K. The solid sulfur in leached residue is separated as float products from other solids by sink-float separation and flotation. The sulfur in float products is purified by evaporation at 413K and recovered."

Jan 1, 2000

By Chao Lian, Hongxu Li, Hao Bai, Wei Wei

"Application of high-emissivity coating on inner walls in industrial furnaces increases the furnace thermal efficiency. The coating with high emissivity strengthens radiation heat transfer in the furnace, however, according to Wien's displacement law and Planck's radiation law, under heating temperature, the wavelengths of the radiation transfer are mostly between 1-5 µm, implying that increasing emissivity of the coating in near infrared band is more effective for higher thermal efficiency. In this paper, a new CuO-ZnO-based coating material sintered at 1600K was developed. The emissivity of the samples were measured and the result shows that, in near-infrared band, the emissivity of the sample reaches 0.98 at 773K with 13at.% of CuO doped in ZnO. In addition, the effects of CuO doping and use temperature on emissivity were also discussed. Furthermore, crystallization behaviors of ZnO-CuO sintering were investigated by DTA,XRD and SEM-EDS etc., which offered information for possible optimal design of the material.1. IntroductionIndustrial furnaces are widely used in various industrial heating. For example, the metal smelting furnace, ore sintering furnace in metallurgical industry; the distillation furnace, cracking furnace in petroleum industry etc,. The research on efficient energy saving technology has important significance. High emissivity coatings are widely used in many high temperature applications to effectively transfer the heat by radiation [ 1]. The theoretical calculation and experimental studies have shown that, coated high emissivity coating in the heating surface is an effective method to enlarge the infrared radiation power [2].At present, the infrared high emissivity coating has been widely used in China, and have been achieved remarkable energy saving effect. According to Wien' s displacement law and Planck' slaw, most energy of the black body at high temperature is radiated in the wavelength range of l-5µm; however it happens that many materials have the low emissivity within this range. Thus, it is important to improve the near-infrared band emissivity of materials [3]."

Jan 1, 2013

By Min Chen

A numerical simulation of the stress field of the solidified shell in the mold during continuous casting of peritectic steel slab was calculated with commercial software. The results showed that the maximal stress on wide face of the solidified shell was located at the corner and near middle of the slab, and it increased with increasing the width of slab. In addition, the stress was also influenced by operating parameters such as superheat degree, drawing speed and cooling intensity of the mold, and the maximal stress value and its position changed with these parameters. For the slab with section size of 3200mm×150mm, the proper drawing speed was around 1.2m/min, with cooling intensity of 5500L/min while the superheat degree was 15°C to 25°C in order to prevent longitudinal crack occurring during peritectic steel continuous casting.

Jan 1, 2009

By Z. Sun

Magnetic fields have been used for inclusions removal from melt and preparation of materials with gradient compositions. Fundamental in these applications is that the induced magnetic forces on the particles/melt can enhance migration and change the interaction behavior. In the present paper, migration and interaction behavior of electrical-insulating particles in a conductive melt under strong magnetic field are theoretically analyzed. It is found that the migration can be considerably enhanced for micrometer sized particles by applying a strong magnetic field. In addition, two forces are involved in the interaction between two particles: the interparticle magnetic dipole-dipole attractive force due to magnetization and the repulsive force induced by flow of the melt. This theoretical analysis renders a better understanding of recent experimental results. Additionally, a new method by using strong magnetic field can be proposed to control the particle size distribution for the preparation of metal-matrix composites.

Jan 1, 2009

By Judy Che, Steven Ceccio, Gretar Tryggvason

"A detailed understanding of drop deformation and solidification is essential for quantitative predictions of geometry and properties of parts made by ballistic particle manufacturing processes. Axisymmetric results of towers built by the deposition of multiple drops are presented. In these computations, fluid flow, heat transfer, and phase change are fully coupled throughout the drop deformation and solidification process. The solution method is based on a single set of conservation equations written for all phases simultaneously. The phase boundaries are treated as imbedded interfaces by adding the appropriate source terms to the conservation equations. A parameter study demonstrates the effect of Weber number, Peclet number, and drop deposition frequency on the final shape of the structure. Numerical results show that most successful method of building uniform towers is when two conditions are met. First, each drop solidifies at the same time in the deformation cycle. Second, the cooling rate is slow enough to allow for good adhesion between drops. The ability to predict the final shape of deposited drops will greatly reduce the amount of experimentation necessary to select the desired set parameters for any artifact.IntroductionMaterial deposition techniques based on layering small molten metal drops holds the promise to build small, coherent three-dimensional structures. In this process, numerous 20-100 µm diameter drops are deposited onto a substrate with a low impact velocity (on the order of 5 mis). Both the momentum and trajectory of each drop are controlled precisely to build up complex parts. This material layering technique differs from processes such as spray forming and splat quenching which involve high impact velocities (on the order of 100 mis) and high frequency deposition with little control over individual drop placement. This process of layering small drops can produce parts with near net shape accuracy, while spray forming produces slabs of material which must then be worked to make a usable part. The ability to computationally predict final drop shape and cooling rate has the advantage of allowing the user to select parameters to produce parts with desired shape and mechanical properties. However, the development of such predictive methods requires a thorough understanding of both drop deformation and solidification"

Jan 1, 1999

By Jefferson Caponero

The tire is an expressive component of Municipal Solid Waste, manly when its occupied volume is considered. Its treatment by pyrolysis stands for a list of advantages, such as: landfill releasing and a production of a high quality fuel. The exploitation of new natural resources is becoming more difficult each day, basically due to the environmental damages caused by this type of activity. This work presents a study on the thermal behaviour of Brazilian tires using thermogravimetric analysis and differential thermal analysis, in order to optimise the pyrolysis process of tires. Samples of I to 2 mm were investigated at atmospheres of nitrogen, argon, oxygen and mixtures of these gases at temperatures up to 1273K, under heating rates between 1 to 50 Klmin . The results showed that the behaviour of each sample is related to both the atmosphere composition and the heating rate.

Jan 1, 2001

By Ping Long, Bin Yang, Jian Wu, Xiumin Chen, Wenli Zhang

In this study, the analysis method of trace element in pure indium using glow discharge mass spectrometry (GD-MS) has been established by correcting the analysis result, which was obtained from non-standard quantitative method of GD-MS. The effect of instrument operating parameters, the resolution and isotopes and the pre-sputtering time on the determination results were investigated respectively. The optimized operating parameters of the instrument were obtained as follows: the discharge current was 37.5mA and discharge airflow was 475ml/min. Mass spectral interferences have been eliminated using selected resolution and isotope. The pre-sputtering time was 30 min. 4 trace elements in two pure samples were determined for 6 times. The RSD were less than 20%. The content of trace elements in indium samples was determined by GD-MS and Chemical Analysis Method of Indium which is tested by inductively coupled plasma atomic emission spectrometry, respectively. The results were consistent with each other.

Jan 1, 2016