Search Documents

By Mukesh Jain

The liquor from potroom wet scrubbers is treated with lime to precipitate the soluble fluorides. The solids after filtration, referred to as scrubber mud, contain in addition to calcium fluoride, alumina, carbon, tars including polyaromatic hydrocarbons (PAH), cryolite and pachnolite and are considered hazardous. This communication deals with the pilot plant scale calcination of scrubber mud with a rotary kiln to obtain non-hazardous fluoride raw materials. Air classification was performed to separate the mudinto aluminarich andcalcium fluoride rich fractions which were then calcined. With proper control of calcination parameters and addition of lime, the carbon and tars were destroyed and hydrogen fluoride emissions were controlled. The calcined products could be used in the steel indusny as a fluxing agent or as a substitute for fluorspar in the production of aluminum fluoride.

Jan 1, 1994

By Rolando Campos

In August 1993, the operation of Refimet Chile's copper custom smelter commenced at La Negra, near Antofagasta in northern Chile. Design smelter throughput corresponded to 235 000 tonnes of concentrate, calcines and copper cements arising from suppliers in the north of the country to produce 90 000 t/y of blister copper. Refimet had initially gained experienced in building and operating leaching, roasting and a blast furnace facility at Rungue, near Santiago, followed by Roasting at La Negra. The initial smelter project was based on conventional reverb- smelting and Peirce-Smith converting and the majority of equipment was 'purchased second-hand and rehabilitated or modified. After only 3 years in production, the treatment capacity was significantly improved by introduction of technical improvements to the original plant operating scheme. Recently, the plant was further expanded to an annual smelting capacity in excess of 400 000 t/y feed, corresponding to around 160 000 t/y copper production. This expansion, referred to as Phase 2, was achieved by modification of the reverb to oxy-fuel firing, addition of a further (second-hand) acid plant, fire refining and anode casting facilities. Parallel development of concentrate injection into enlarged converters-also took place. Following successful commissioning of Phase 2 expansion, initial engineering studies for a third expansion phase have been completed. This aims to use leading technology based on bath smelting of bone-dry concentrates in a Continuous Reactor. This paper provides an overview of the relatively short plant history, its development and improvements together with operating indices achieved.

Jan 1, 1998

By Phillip A. Armstrong, Charles A. Lewinsohn, John H. Gordon

"This paper describes the opportunity offered by employing systems based on mixed conductive ceramics, in particular, ceramics conductive to oxygen ions and electrons, in reducing CO2 emissions from metallurgical production. Membranes based on these mixed conducting properties enable commercial viability of several attractive metallurgical processes. One of these processes utilizes modular, ceramic-membrane structures for the generation of pure oxygen, in tonnage quantity. The membrane-based systems offer significant capital savings and operating efficiencies in various metallurgical processes. The current status of this technology is summarized below.IntroductionCryogenic oxygen supply technology is currently the state-of-the-art for applications that require large quantities of oxygen (hundreds to thousands of tons per day). Cryogenic technology, however, requires substantial energy inputs and, hence, adds significant costs and emissions to processes. Furthermore, cryogenic oxygen supply technology is mature and there is relatively little potential for substantial capital cost reduction or efficiency improvement in coming decades. Non-cryogenic technologies offer a means to reduce the environmental footprint and cost of the oxygen supply facility in various applications.Ion Transport membranesCommercially available non-cryogenic air separation technologies, such as adsorption-based and polymeric membrane-based methods, do not afford the economies of scale that the cryogenic distillation enjoys. Therefore, industrial gas industry researchers began searching for alternatives to the relatively inactive and unselective polymeric membrane materials available. In the late 1980’s, Air Products began developing a new class of highly selective membrane materials with exceptionally high activity for oxygen transport. The materials constitute a class of oxide ceramics, and conduct both oxygen (as oxygen ions) and electrons in the same membrane, separating oxygen from air electrochemically. Numerous detailed process economics studies have shown that, based on these ion-transport membranes (ITM’s), the cost of oxygen can be reduced by approximately one-third relative to that obtained from state-of-the-art cryogenic oxygen supply technology, through a combination of capital cost savings and efficiency improvements. [1,2,3]"

Jan 1, 2008

By Ann M. Hagni

"Ceramic matrix composites are inorganic materials that are particularly resistant to heat and abrasion. A magnesia (MgO) and aluminum nitride (AlN) based composite is formed by exposing a magnesia preform to a metallic alloy block in a nitrogen atmosphere at 950°C. The metallic alloy, which is composed primarily of aluminum, is wicked into the preform. Aluminum nitride matrix is grown between MgO particles as the wicked metallic aluminum reacts with nitrogen. Unused metallic alloy, remnant metallic alloy (carcass), and composite produced after 8 hours, 50 hours, and 225 hours of processing are characterized mineralogically. Reflected light microscopy, transmitted light microscopy, scanning electron microscopy, energy dispersive spectroscopy, and X-ray diffraction techniques reveal that in addition to anhedral to euhedral AhNi, AbSbSr, and Al crystallizing in the metallic alloy carcass, AIN and (Al,Si)N have formed as well. Nitride rings and nodules in the carcass may hinder AIN growth in the composite. Fine-grained residual AhNi and AhShSr are dispersed throughout the composite matrix. The nitride matrix is composed of AIN and (Al,Si)N. Rim replacement of MgO by spine! occurs in the composite. Aluminum nitrides in the metallic carcass cathodoluminesce deep violet-blue, unlike non-luminescent AIN in the composite matrix. This distinction in cathodoluminescence suggests a different mode of formation for composite AIN than for carcass AIN. Phase interpretations and textural characterizations deduced from the implementation of sophisticated mineralogical techniques have contributed to the understanding, and will aid in the improvement, of MgO/ AlN-based ceramic matrix compositeprocessing."

Jan 1, 1999

By F. J. Tavera

Recently Jameson cell technology has gained acceptance in both mineral and non-mineral applications, mainly because of the high degree of contact between the involved phases in the downcomer, fact that leads to an efficient collection performance. The key for an acceptable performance of the downcomer operation depends on the stability of the jet zone, the mixing zone, and the plug flow zone. in this work the behaviour of the downcomer of a laboratory Jameson cell is reported, as a function of gas hold-up, superficial gas velocity, superficial liquid (or slurry) velocity, and length of the operating zones. The presence of carbon is evaluated in terms of its effect on the gas hold-up and bubble surface area flux. The influence of the downcomer operating conditions on the gas-liquid disengaging cell is presented. Keywords: Jameson cell, downcomer, gas hold-up, mixing, plug flow, conductivity.

Jan 1, 2003

By Lv Guozhi, Ren Xiaodong, Liu Yan, Dou Zhihe

"This paper investigated a new desulfurizer, dolomite and ferrosilicon. Magnesium vapor produced by silicothermic reduction of dolomite and ferrosilicon in an immersion tube of molten iron was injected into the molten iron by carrier gas through the underpunch of the tube and desulfurization reaction occurred. In order to explore the desulfurization process of molten iron by the new desulfurizer, the thermodynamics, and experiments of magnesium vapor production and desulfurization have been studied. Through thermodynamic calculation, the reaction temperature of magnesium vapor production by 75ferrosilicon and light-burned dolomite is 1838K in the standard state and decreased with the decreasing partial pressure of magnesium vapor, PMg· When PMg=25kPa, the reaction happens at 1673K. From experiments of magnesium vapor production, reduction efficiency of Mg vapor is about 60 % in 15 minutes at 1673K. From hot metal experiments, the desulfurization efficiency is 89.35%, and the lowest sulfur concentration after desulfurization is 46ppm.IntroductionPretreatment desulfurization of hot metal has become a necessary step in modem optimizing steelmaking process for its cheap cost, which can not only liberate of blast furnace productivity and reduce the burden of produce steel, but also effectively improve overall economic efficiency of the iron and steel system[l-ZJ_ At present, injection magnesium particle is one of the two main methods of desulphurization in hot metal owing to its strong affinity for sulphur, low amount of slag produced, low iron loss in slag skimming and low equipment investment[3l. However, there are still some insufficiencies on the hot iron pretreatment with magnesium particles at present[4-5l"

Jan 1, 2013

By H. Y. Sohn

The ignition and combustion of chalcopyrite particles under suspension-smelting conditions, in which the particle-particle interaction is neglected, has been analyzed by considering the intrinsic kinetics of oxidation and heat and mass transfer between the particle and its surroundings. Reasonable agreement has been obtained between the calculated results and experimental results from a laminar-flow furnace reported in the literature. This computation- al procedure has further been applied to flash-smelting conditions. Under suspension-smelting conditions (Sh = Nu = 2), chalcopyrite particles ignite at around 960 K. The effects of various parameters, such as oxygen concentration, particle size, and gas temperature, have also been evaluated. Comparison between calculated results in this work and experimental observations indicates that SO is the important gaseous product that forms at the surface of the particle.

Jan 1, 1993

By Yunhua Gan, Xiaowen Chen, Yang Tong

Experimental studies of electro-spraying were carried out using ethanol as fuel in a microcombustor under combined electric field. And the effects of different electro-spraying modes on the combustion efficiency were analyzed. Results showed that when ring electrode potential was invariant, there were four different electro-spraying modes with the variations of nozzle potentials, which were varying with the flow of ethanol. The cone-jet mode was the stablest one during the whole experimental process. The atomized ethanol was ignited and combusted stably near the steel mesh, the combustion efficiency increased firstly and then decreased along with the increasing of the equivalent ratios, reached the maximum values when the equivalent ratio equal to 1.0. And the maximum values were the highest at the cone-jet mode, and the lowest at the pulsed-jet mode.

Jan 1, 2016

By H. Doostmohammadi

During the tapping of liquid steel from Electric Arc Furnace (EAF), some slag is carried over into the ladle. High levels of FeO and MnO in slag carryover increase the oxygen activity in steel melt leading to oxide inclusion formation during the ladle treatment. The demand on cleaner steels requires minimization of carryover slag. In this work, the effect of EAF slag carryover on ladle slag-steel equilibrium calculations for a hot working tool steel was studied. Steel and slag sampling were done in Uddeholm Tooling AB in Sweden. XRF and OES techniques were used to determine chemical composition of samples. The quantity of slag carryover was calculated based on a mass balance followed by thermodynamic calculations on metal-slag equilibrium using Thermo-Calc software. The agreement between predictions and experimentally determined compositions was good. This leads to the development of a prediction method for optimizing the production of other tool steel grades.

Jan 1, 2009

By Wen-long Zhan, Zhe Ning, Jun-hong Zhang, Ji-hui Liu, Zhi-jun He, Qing-hai Pang

The influence of microwave irradiation and ultrasonic vibration on granularity of 0.074 mm pulverized coal was investigated in this research. It is indicated in the results that the granularity of coal decreased after microwave treatment, which led to the increased in specific area of pulverized coal in combustion reaction and consequently optimized the kinetic condition of combustion reaction. Higher ultrasonic power may lead to better performance of PC in combustion. The optimum condition for ultrasonic treatment is 10 min under 350 W microwave power.

Mar 1, 2017

By Jianhua Xin, Min Chen, Cuihuan Huang, Shan Yu, Xiaoao Li, Nan Wang, Guanghao Chen

Copper enrichment behavior in continuously cast slab induced by scale formation after continuous cooling in H2O vapor atmosphere and consecutively in air has been experimentally investigated by combining with SEM-EDS analysis, for the purpose to examine the effects of initial slab surface temperature and contents of copper and nickel. For Slab 1 with copper content of 0.1 percent, no visible copper enrichment is found at scale-substrate interface irrespective of the various scale microstructures formed at different initial slab surface temperatures. For Slab 2 with higher contents of copper and nickel, copper-rich phase accumulates and stays at scalesubstrate interface under the condition of lower initial slab surface temperature; while Cu-rich phase in the porous scale formed at higher initial slab surface temperature is noted with simultaneous Ni-enrichment appearing in front of the steel-scale interface. Both a porous scale and high nickel content work together to provide pores for copper-rich phase migration away from interface and occlude within the scale layer.

Jan 1, 2016

By Soumendra Basu, Uday Pal, Yang Yu, Srikanth Gopalan, Karl Ludwig, Deniz Cetin, Jacob Davis

"A limiting factor for Solid Oxide Fuel Cell (SOFC) performance is the oxygen reduction reaction (ORR) at the cathode surface. Changes in the surface composition and structure on annealing at 800°C has been studied, since these can influence the ORR. Idealized single crystals of cathode materials La0.8Sr0.2MnO3 (LSM) and La1-xSrxCoyFe1-yO3 (LSCF) were grown as heteroepitaxial thin films on lattice matched single crystal substrates. Changes upon heating the films to operating temperature and pressures were characterized using various synchrotron x-ray techniques. Total Reflection X-ray Fluorescence (TXRF) measurements, which probe compositional changes, were made at high temperature in real time. The LSM surfaces were found to develop manganese enrichment when heated. Highly strontium doped LSCF were found to develop strontium-rich surfaces. HArd X-ray PhotoElectron Spectroscopy (HAXPES) was used to investigate the electronic structure of the materials. Highly strontium doped LSCF precipitates a surface strontium phase that contains both oxide and carbonate contributions.IntroductionSolid oxide fuel cells (SOFCs) are chemical to electrical energy conversion devices that could potentially reshape how energy demands are fulfilled. SOFCs have a potential efficiency over 70%, fuel flexibility, low emissions, and low degradation over long time scales. Commonly, SOFCs are operated at high temperatures (above 800°C). At these temperatures expensive housing is needed to contain an operating stack as well as coatings to contain the oxidation of the metallic interconnects. Lowering the temperature of an operating device would allow for more conventional materials to be used, thus lowering overall cost. Understanding the reaction kinetics of the oxygen reduction reaction at the surface of the cathode is vital to designing a system that will perform well at lower temperatures. A commercialization goal is to reduce operating temperatures without sacrificing performance.In order to exploit the advantages of SOFCs, an understanding is needed of the surface chemical states of cations on the surface of the cathode and how this relates to the oxygen reduction reaction (ORR):"

Jan 1, 2014

By Chengyi Ding, Xuewei Lv, Senwei Xuan, Chenguang Bai, Kai Tang, Gang Li

Sinter is an important iron-bearing material charged into blast furnace. Calcium ferrite (CF) is one of the most significant liquid phases in fluxed sinter. The isothermal reduction kinetics of CF and CF8M (n(CaO):n(Fe2O3) = 1, wt%(MgO) = 8) with 30% CO and 70% N2 gas mixtures at 1123, 1173, and 1223 K were investigated through thermogravimetric analysis in this study. Rate analysis illuminates that the reduction processes of CF and CF8M are mainly expressed as a typical two-stage reaction. Sharp analysis indicates that CF and CF8M reduction is expressed by the Avrami–Erofeev equation presenting a 2D shrinking layer reaction. The apparent activation energy values of CF and CF8M reduction are 46.9 and 31.8 kJ mol−1 individually based on model-free method.

Mar 1, 2018

By S. M. Hay

The zinc content of blast furnace and basic oxygen furnace dusts is low compared with electric arc furnace dusts and it is generally not economical to treat the dusts to recover zinc. However, they have a high iron content and removal of the zinc would allow recovery of the iron values. A literature review and thermodynamic analysis was undertaken and, as a result, several smelting options were identified. This paper describes experiments undertaken to develop understanding of metallurgical aspects of these processes which are not amenable to theoretical analysis. Dusts from an Australian steelworks were characterised in order to determine their mineralogical make-up and the form of the iron. The processing aspects investigated in the laboratory were slag-metal equilibrium and solid-state pre-reduction using reducing gases of compositions expected from bath-smelting processes. Particular attention. was paid to the deportment of zinc, sodium, potassium, phosphorous and sulfur between the phases formed during smelting and pre-reduction. The smelting results indicate that less than 10% of the zinc, sulphur, sodium and potassium report to the metal. About 99% of the zinc and potassium and about 80% of the sodium could be volatilised from the dusts by reducing them at 1,000°C with mixtures of CO, CO2, H2 and H2O even when metallic iron was not formed. The experiments indicate that smelting of blast furnace and basic oxygen furnace dusts should produce hot-metal of a composition which can be blended into the main stream of hot-metal in the steelworks.

Jan 1, 1994

By Susumu Okabe, Etsuji Kimura

"The Mitsubishi Continuous Copper Smelting and Converting Process is the typical applications of injection metallurgy to nonferrous metallurgical operation, where the top blowing multiple lance system is employed for the continuous feeding of the raw materials and reaction gases into the molten bath. This results in an effective dispersion of the reactants into a strongly agitated bath. These are considered as the major advantage of the process with respect to the high production efficiency. On the other hand, however, the strong agitation may cause a considerable amount of refractory wear, and the melt splash generated by the lancing may also have negative effects on the productivity, i.e. the increase in the refractory wear, the metal loss, the heat loss, and the accretion growth, etc. Therefore, the optimization of the blowing condition as wen as furnace design is very important to achieve a stable and efficient operation, and fundamental understanding of the injection, agitation, and splashing is badly needed.In this paper, fundamental aspects of the Mitsubishi Process regarding injection, especially splashing phenomena, are discussed. The splashing on a vertical plane caused by the top blowing gas injection onto liquid surface was investigated through physical model study. As a result of the study, the splashing rate on the furnace wan was wen correlated with the physical properties of the bath materials, gas velocity, cavity shape, lance/wall distance and ceiling position. Obtained equations were compiled in a computer program and have been successfully applied to the evaluation of the furnace design. IntroductionInjection metallurgy is an application of gas/solid-in-liquid dispersing operation to the metallurgical processing, and has been widely adopted in various fields in order to improve their efficiency or productivity. The dispersed small particles of gas or solid materials in the liquid phase result in increased interface area, and injected momentum causes an agitation and enhanced heat and materiel transfer. Typical examples of injection metallurgy are LD converter for steel making, PS converter, Noranda process, Isasme1t for copper making, and Mitsubishi Material's continuous copper smelting and converting process, and so on."

Jan 1, 1996

By R. Singh, C. Gong, J. Chaudhry

"Metalorganic chemical vapor deposition (MOCVD) is an ideal technique for the deposition of conducting and non-conducting oxide based thin film materials. In this paper we have presented a study of photo assisted MOCVD for the low temperature deposition of a number of oxide based advanced materials. We have used incoherent light sources as the source of optical and thermal energy in our MOCVD system. The vacuum ultraviolet (VUV) and ultraviolet (UV) photons can enhance the surface reaction of the absorbed molecules through the perturbation of the electronic state of binding between the absorbed molecules and the solid surface. Unlike plasma process, no surface damage is expected and high quality materials have been deposited. At a given substrate temperature, the performance of deposited film depends on the lamp configuration.INTRODUCTIONMetalorganic chemical vapor deposition (MOCVD) has become the standard manufacturing technique for the deposition of large area thin films of compound semiconductors. l.(.w-cost, high crystalline quality, atomically clean and sharp interfaces, atomic layer epitaxy, high throughput rates and potential for direct writing are some attractive features of MOCVD. Due to a number of potential advantages mentioned above, MOCVD is considered as an ideal technique for the deposition of various electronic and optical materials for a wide variety of applications. Rapid isothermal processing based on incoherent radiation as the source of optical and thermal energy is emerging as the key low thermal budget (integral of processing time and temperature) processing technique for the fabrication of current and next generation of microelectronic and optoelectronic devices and circuits [1]. In this paper we have demonstrated that the design of the lamp assembly plays an important role in determining the properties of the materials deposited by RIP assisted MOCVD. We have studied the growth rates, structural properties and electrical properties of Y2O3/Si structure. At a given substrate temperature, best results are obtained for the lamp assembly that provides maximum number of VUV and UV photons."

Jan 1, 1994

By Zheng-qi Guo, De-qing Zhu, Feng Zhang, Jian Pan

Iron mainly exists as the magnetite and fayalite, while copper is primarily dispersed in the form of fine matte particles in the copper slag, which is difficult to recover by conventional separation techniques. In this paper, the feasibility of an integrated technological route to improve beneficiation of copper and iron components from copper slag through the modification of molten slag was investigated, and the results shows that: the copper grade of rougher copper concentrate was increased from 6.43 to 11.04%, iron recovery from magnetic separation was increased significantly from 32.40 to 63.36%, and other evaluation indexes were changed slightly, in comparison with unmodified copper slag. Meanwhile, the grains of the target minerals in the modified slag grew considerably to a mean size >50 lm after slow cooling. Ultimately, the beneficiation efficiency of copper and iron was improved because of the ease with which the target minerals were liberated.

Mar 1, 2017

By Shuqiang Guo, Gonghui Yang, Xingxing Zhang, Yuyang Bian, Song Chen, Weizhong Ding, Yinhe Liu, Lan Jiang

One of the most promising refractory materials for application is zirconia in melting superalloy. In this work, the properties and phase composition of magnesia partially stabilized zirconia ceramics (MgO-PSZ) under different sintering temperatures were systematically investigated. Commercial magnesia partially stabilized zirconia (MgO-PSZ) powders were selected as the starting materials. The magnesia partially stabilized zirconia phase composition was measured by X-ray diffraction (XRD), the density of sintered samples was tested by vacuum density instrument, the thermal expansion were obtained by thermal dilatometer from ambient temperature up to 1450°C, and the microstructures of MgO-PSZ were characterised by scanning electron microscope (SEM). The results indicated that the properties of thermal expansion, densification, microstructures and phase composition were significantly affected by sintering temperature. Densification was consistent with SEM micrographs of MgO-PSZ at different sintering temperatures.

Jan 1, 2015

By J. W. Perez

Raw coal will often break intragranularly in either a completely random way or in a differential mode where one species will have a different rate of breakage than another. Locked coal-ash and coal-pyrite particles can also break by the preferential detachment of one species from another along zones of inherent weakness in locked particle assemblages. The mode. cf breakage is largely a function of the nature of the feed, but it is also influenced by the comminution device and the operating variables. Evidence of breakage of particles in the various modes is seen in the crushing of raw coal and middlings particles with a rotary beaker, jaw crusher, rolls, hammer mill and rod mill. Evidence from the literature indicates the detachment mode is often important for coal, ores and metallurgical products. Further confirmation comes from the crushing of a specially prepared 'ore' of sized magnetite in plaster of Paris.

Jan 1, 1988

By Duclerc Fernandes Parra, Ademar B. Lugão, Nilton Lincopan, Fernanda Esposito, Vijaya Rangari

Polymeric hydrogels are natural or synthetic systems, which have gained interest due to their high biocompatibility with soft tissues. These types of hydrogels have been used for wound dressing as a drug delivery system. Here in this study the polymeric hydrogels based wound healing systems were prepared using poly (N-vinyl-2-pyrrolidone) (PVP), poly (ethylene glycol) (PEG), agar and neomycin drug followed by gamma irradiation to promote crosslinking and sterilization. The influence of irradiation process with 25 kGy dose was investigated. The gel fraction and maximum swelling were estimated using physicochemical methods and found about 95% gel fraction and 1100% swelling after 8 h of immersion. Neomycin released from hydrogel was carried out by Liquid Chromatography-Mass Spectrometry method and the drug concentration remained constant for 48 h. Hydrogel/neomycin exhibited antibacterial effects against Staphylococcus aureus. With these results, it can be inferred that hydrogel/neomycin is a suitable candidate for wound dressing.

Mar 1, 2018