Search Documents

By Yuanbo Zhang, FENG ZHOU, Guanghui Li, Zhengwei Yu, RuijunWang, Tao Jiang

Composite agglomeration process (CAP) of iron ore fines has been proved an effective route for ironmaking burden production, and is characterized by low the fuel consumption and high the productivity compared with the traditional sintering process. Sintering behavior of pelletizing feed in CAP has not been studied fully yet. In this study, individual pellet and simulated CAP cells were roasted under the simulated sintering conditions. The compressive strength, FeO content and microstructures of roasted samples were investigated. The results show that pelletizing feed either from magnetite ore hematite concentrate can be indurated under the conditions of conventional iron ore sintering. Hematite pelletizing feed has better sintering property than magnetite pelletizing feed. Pelletizing feed consolidation in CAP cells is identical to the individual pelletizing feed, but the strength of CAP cells is much higher than the individual pelletizing feed. Higher basicity in both pelletizing feed and matrix feed is beneficial to the strength of CAP cells. Individual strength of pelletizing feed is not the decisive factor in CAP as the pelletizing feed has been embedded into the matrix with high basicity and formed an organic whole. The main chemical compositions and basicity of pelletizing feed and basicity matching with matrix feed is important.

Jan 1, 2015

By Murat Baydogan

Effect of retrogression and reaging treatment on hardness and stress corrosion cracking resistance of 7075 aluminum alloy was investigated. As received 7075 alloys in T6 temper condition were retrogressed at 170, 220, 240 and 380°C for different durations between 15 s and 60 min. Subsequent reaging was made at the T6 aging condition. Treated materials exhibited higher hardness and better stress corrosion cracking resistance than T6 temper in a wide range of retrogression temperature and time. The highest hardness was obtained after retrogression at 170°C for 210 s followed by reaging, corresponding to 20% hardness improvement. Improvement in stress corrosion cracking resistance of the alloy by as much as 85% was also observed. In this paper, improvements in hardness and stress corrosion cracking resistance are discussed on the basis of the microstructural changes during retrogression and reaging treatment.

Jan 1, 2006

By Satian Niltawach

Iron sulphate jarosite through which iron in zinc sulphide concentrate feed is removed from the production circuit of conventional roast-leach-electrowin process, is chemically unstable and environmentally hazardous even if it is mixed with lime. If zinc silicate ore is used at similar chemical conditions in place of calcine in the jarosite precipitation, the resultant silico-jarosite residue having been mixed with lime is chemically stable and environmentally friendly. The recovery of zinc from silicate ore is also higher than that from calcine.

Jan 1, 1994

By M. Kobashi, T. Choh, N. Kanetake

"A new processing route, which enables the cost-effective and energy- saving fabrication of metal matrix composites, have been proposed. The pressureless infiltration of the reactive powder blend with molten aluminum was investigated in this work. The molten aluminum infiltrated into the [Ti + C] powder blend spontaneously, whereas the spontaneous infiltration into the TIC powder phase did not occur under the same experimental condition. The processing time was shortened and· the processing temperature was .lowered by adding the aluminum powder in the [Ti + C] powder. The differential thermal analysis revealed that the aluminum powder in the powder blend melted at 933K and then ignited the reaction between titanium and ·carbon. However there was an .optimum additional amount of aluminum in the powder blend. The TiC formed in situ had three-dimensionally continuous morphologyIntroductionThe squeeze casting process has been used as one of the processing routes for aluminum matrix composites. [1, 2]. Non-reactive metal-ceramic systems have been, generally, used in this technique in order to prevent the degradation of the ceramic phase. Materials obtained by this process basically consist of a continuous metal matrix and discontinuously dispersed ceramic particles. Reactive systems have begun to be introduced into the infiltration process· recently [3A]. Since the ceramics are synthesized in-situ, this process can provide a continuous ceramic matrix [5]. This is one of the outstanding features of this technique in that a bulk ceramic-can be synthesized at relatively lower temperatures in a short time. Another advantage is that the highly reactive combination of a ceramic with a molten metal is in many cases wettable [6], which enables a spontaneous infiltration."

Jan 1, 2000

By Kikuo Okuyama, I. Wuled Lenggoro, Manabu Shimada

"Aerosol processing of materials such as (i) gas-to-particle conversion process (e.g., Chemical Vapor Deposition (CVD) method) and (ii) liquid (or droplet)-to-particle conversion process (e.g., spray pyrolysis) has become of major interest to produce novel submicron- or nanometer-sized particulate material used in electronic and chemical industries. After reviewing recent theoretical and experimental researches on the evaluation of properties and morphology of fine particles by the CVD and spray pyrolysis methods, the importance of the process engineering approach· for aerosol processing of materials and the use of advanced aerosol measurement technology have been pointed out.IntroductionMaterial synthesis via aerosol processing offers a route to producing nanometer-sized and submicrometer-sized particles of high purity with specifically tailored chemical and physical properties. Especially, single nanometer-sized particles (nanoparticle materials) are considered to play an important role in the synthesis of nanostructured materials as well as in nanotechnology in 21st century due to their quantum effect and so on.However, the transformation of gaseous or liquid precursors to the final functional particulate matters consists of various complex chemical and physical processes. In order to control the size distribution and morphology of produced particles, it is important to analyze and model various phenomena, such as gas-phase or liquid-phase chemical reaction, nucleation, condensation, agglomeration and sintering that occur simultaneously in aerosol material processing. By introducing the Aerosol Science and Materials Science, the authors have been trying to model the changes in particle properties and morphology by gas-to-particle conversion and droplet-to-particle conversion processes. The authors have also been trying to obtain the experimental data on the particles properties as accurate as possible."

Jan 1, 2000

By Filippos Patsiogiannis

Laboratory size (5 kg) aluminum killed low carbon steel melts were desulfurized with synthetic fluxes in zirconia crucibles. The sulfur, oxygen, aluminum, silicon, and manganese contents in the melt were determined as a function of refining time and temperature. With a good argon shield and synthetic flux cover, melt reoxidation was not observed. Sulfur removal followed first order reaction kinetics. The effectiveness of calcia saturated calcium-aluminate (12CaO.7Al2O3) based fluxes in desulfurizing the steel melts was evaluated. The effects of initial sulfur level of the melt, weight of the flux (slag), and additions of tellurium, fluorspar, and barium oxide to the melt on the kinetics of desulfurization were also studied.

Jan 1, 1993

By M. S. Moats

The treatment of oxidized residues of zinc with high iron content continues to present a technical challenge in both the steel and zinc industries. Two main problems are commonly identified and include high treatment costs and environmental concerns about contaminated, iron-bearing residuals. A new approach to this problem is described in which selective separation of the iron and zinc into salable products may be potentially feasible. The waste material is first leached to give a solution having an approximate concentration of 110 g/l Zn, 15 g/1 Fe and 40 g/1 H2SO4 and other impurities such as Pb, Cd, Cu and Sb. A suitable organic, such as D2EHPA, is used to load the majority of the iron. The aqueous phase is then acceptable for zinc electrowinning after standard solution purification. The novel step in the flow sheet is the efficient recovery of the ferric iron from the organic solvent using a solid metal to reduce the iron to the ferrous state. The Fe+2 is easily stripped into an aqueous phase in a relatively pure form, suitable for use in water treatment. Process parameters and possible flow sheet designs are described and discussed.

Jan 1, 1995

By Don Ibana

Supported by the Minerals Council of Australia (MCA) through the Minerals Tertiary Education Council (MTEC), three Australian universities–Curtin University, Murdoch University and the University of Queensland–have formed the Metallurgical Education Partnership (MEP) to jointly develop and deliver an engineering design capstone unit–Metallurgical Process and Plant Design–in their respective undergraduate programs in extractive metallurgy, in order to enhance the students’ educational experience. A unique feature of the program is the close interaction of the students in all three universities and a significant involvement of industry professionals. Now in its sixth year, it is clear that this unit is achieving its objectives

Jan 1, 2014

By Xuemei Zheng, Aiyuan Ma, Guojiang Li, Tingfang Xie, Jinhui Peng, Libo Zhang

A new microwave roasting technology for the removal of Cl from zinc oxide dust is proposed in this paper. The effect of important parameters, such as roasting temperature, holding time and stirring speed, were investigated and the process conditions were optimized using response surface methodology (RSM). The experimental results show that zinc oxide dust dechlorination rate can reach more than 95.66% and meet the requirements of wet smelting electrolysis when controlling the stirring speed of 60 r/min,roasting temperature of 650 °C, holding time of 30 min. In addition, the effect of roasting temperature and holding time on removal ef ficiency of Cl was most signi ficant. As a result, the Cl content was decreased without the risk of pollution. This makes it as a good choice for a more ecological treatment of zinc secondary resources.

Mar 1, 2018

By Alexandra Anderson

A computational fluid dynamic (CFD) model has been developed using ANSYS Fluent 17.0 to help identify areas of high wear within the refractory lining of a secondary lead reverberatory furnace. Once a base case simulation was validated using data from an operational furnace, areas of potentially high refractory wear were determined through the calculation of the temperature and velocity distributions within the furnace and on the hot face of the refractory lining. The CFD model was used to assess whether the predicted areas of high refractory wear could be minimized through changes burden geometry. The results showed that shape of the burden geometry greatly affected the overall flow patterns and heat transfer within the furnace.

By Yousef Mohassab, Hong Yong Sohn, Mohamed Elzohiery

As part of the development of a novel flash ironmaking process at the University of Utah, a labscale flash reactor was used to produce iron directly from iron oxide concentrate. This work tested the feasibility of the novel flash ironmaking process using the partial combustion of hydrogen as fuel and reductant. In this flash reactor, the energy required to reduce concentrate particles was obtained from the internal combustion of hydrogen and oxygen with complementary energy from electrical resistance heating to compensate for the heat loss. After the reaction shaft was electrically pre-heated, hydrogen and oxygen streams produced a non-premixed flame inside the reaction shaft. Various conditions such as flame configuration, flame power, positions of concentrate feeding ports, excess hydrogen amount and residence time were tested. More than 90% reduction of magnetite or hematite was achieved at temperatures as low as 1175 oC with < 100% excess hydrogen in <10 s of residence time.

Jan 1, 2016

By Jose R. Parga

In mining operations, cyanidation is the ,predominant method by which gold and silver are recovered from their ores and it is recognized that cyanide consumption can be a major factor that contributes to the operating costs for such operations. Also after extraction and recovery of precious metals a certain amount of cyanide is delivered to the tailings pond and must be considered with respect is environmental problems due to the toxicity of cyanides. In this regard, the Air-Sparged Hydrocyclone (ASH) has been used as a reactor for the treatment of cyanide solutions in two ways; first for cyanide recovery by acidulation using the Mexican modification of the Mills-Crowe process and second for cyanide destruction by oxidation with the use of chlorine dioxide (ClO2). In both cases, excellent performance can be achieved using the high capacity ASH system.

Jan 1, 1998

By Bowen Li

Silicon Carbide is an excellent refractory material. Its physical properties make it extremely useful, particularly in applications where corrosion resistance and wear are important considerations. Commercial silicon carbide refractory is frequently manufactured by bonding silicon carbide particles with clay; however, clay may cause problems in the sintered products. This study investigates the potential of replacing a portion of the clay with andalusite powder. The results show that micron size andalusite powder can improve not only the strength of the refractory but also the sinterability. The mechanisms for these improvements are discussed.

Jan 1, 2006

By Krishna Parameswaran

This paper illustrates sustainability considerations in copper hydrometallurgy using examples of practices at ASARCO LLC, an integrated U.S. primary copper producer. Using the classic Brundtland Commission development of sustainable development, i.e., “development that meets the needs of the present without compromising the ability of future generations to meet their own needs,” the paper discusses how copper hydrometallurgical processes can be sustainable. The examples used to illustrate sustainable development and related concepts include: water conservation opportunities in milling and leaching operations; implementing green chemistry and promoting product stewardship in the electrorefining of copper.

By Janene Barter

Telfer Gold Mine treats both gold/copper oxide and sulfide ores in a remote location in the Great Sandy Desert, Western Australia. Currently, the oxide gold ore is treated in a conventional CIL circuit by blending the low and high grade copper ores to minimise cyanide consumption and allow smooth operation. The sulfide ore is treated through a flotation circuit to produce pyrite and copper concentrates. The pyrite concentrate is treated in the CIL. Copper concentrate is stockpiled and sold to a smelter for further processing. In recent times, as the depth of the pit has increased the copper head grade has also increased, to the point where the ore was becoming uneconomical to treat. In addition, it was desirable to reduce the amount of cyanide reporting to the tails dam both from an environmental and economical viewpoint. Newcrest Mining Limited engaged GRD Minproc Limited to evaluated a process to reduce the amount of cyanide entering the tail dam with consideration given to copper recovery. From this investigation, the Sulfidisation, Acidification, Recycle and Thickening (SART) process was selected. A detailed testwork program for SART was undertaken with the objective to design and construct a SART plant at Telfer. This paper outlines how the SART process was chosen and summarises the testwork that led to the design of the SART plant. It also touches on some of the important issues for designing this type of process.

Jan 1, 1998

By Fernando Aracati Botelho, Jose Antonio Silva Souza, Luis Alves Venancio, Emanuel Negrão Macedo

"1 AbstractThe production of alumina from bauxite using the Bayer process generates 0.7 to 2.0 ton of the residue known as red mud and about 800 kg of CO2 per ton of alumina. The direct use of exhaust gases to react and neutralize the bauxite residue may allow a double gain: open a wide range of new applications for bauxite residue reducing its reactivity and sequester from 3 8 to 107 kg of CO2 per ton of alumina. This paper shows a pilot scale reaction of a suspension of bauxite residue-water with flue gas produced from direct burning oil, similar to the exhaust gases of a refinery. Two different types of reactors are used, a spray tower and a packed column. The inlet and exhaust gases are analyzed using electrochemical cells and non-dispersive infrared sensors. The pH of the suspension is monitored during the reaction and after to evaluate the buffer effect. 2 IntroductionThe production of millions of tons per year of alumina around the world generates from 0. 7 to 2.0 ton of the residue known as red mud (RM) per ton of alumina. The vast majority of the red mud is stored in large sealed lakes. Due to the high reactivity this material is considered dangerous and currently there is no operating process capable of reusing all the material produced at any refinery. These lakes after filled of solid material eventually have the surface revegetated [4]. In any case they will remain as an environmental passive and needs monitoring for decades. The search of a industrial process that combines the reduction of the CO2 emission and the reduction the pH of the red mud opening the possibility of large scale and economically viable ways is the main objective of this work.The use of the exhaust gases of the refmeries to neutralize the bauxite residue may allow a double gain: Open a large array of new applications for the residue with the reduction of its reactivity and sequester millions of tones ofCO2 plus other gases like SO2 [7] and NOx. This project studies the reaction of the exhaust gases from a boiler burning diesel with RM in different reactor types and conditions in order to obtain parameters to design equipment capable of process this reaction on a larger scale. With these objective compositions of red mud were processed with flue gas at concentration similar to the exhaust gases of the calcination process and boilers of the refmeries."

Jan 1, 2012

By D. Morin

A general study of gold refractory arsenopyrite-pyrite concentrate bioleaching has been carried out including two continuous bioleach testworks at different sizes, namely one at a laboratory scale with a 100 I unit at a 2 kg/d dry solid flowrate and the other at a pilot scale at a 100 kg/d dry solid flowrate. Both tests show a 80% bioleaching of arsenopyrite in about four days of treatment and with the same kinetic. Pyrrhotite is attacked at the earlier stage of the bioleaching but pyrite remains unaffected. The weak potential of oxidation associated with the decomposition of arsenopyrite and the abundance of arsenite leads to a high grade of elemental sulfur in the bioresidue which consumes the major part of the cyanide during the gold recovery. Furthermore. the arsenite and ferrous produced in solution have to be oxidized to obtain a stable precipitate in the waste products and as outlined in previous works of other authors on this subject the addition of iron to obtain a Fe/As molar ratio at least above 3 is necessary. The agitation equipment used in the pilot unit allowed an optimization study calculation for scaling-up the design and power requirements of an industrial installation. For the pretreatment of a gold refractory As high-graded concentrate the reagent cost has the greatest part in the operating cost of the biooxidation step due to the necessary retreatment of the biosolution. In that conditions the power cost is quite marginal. actually it is significant for the treatment of pure pyrite.

Jan 1, 1991

By Asmo Vartiainen

The viscosity of liquid Fe-O-SiO2 -slag at copper smelting conditions was investigated using a rotational viscometer. The studied parameters were oxygen partial pressure (10" °-10"6 bar ); composition of slag (Fe/SiO2 ratio), and temperature (1250-1400°C). The viscosity values are presented as a function of Fe/SiO2 ratio and as isoviscosity curves in ternary FeO-Fe2O3-SiO2 diagrams. The increase in viscosity at high silica contents can be accounted for the polymerisation effect of SiO4/4- -anions. At high ferric iron contents, higher oxygen partial pressure, the viscosity values increase especially near the magnetite saturation. The viscosity values are highest at the double saturation of silica and magnetite. At lower silica and ferric iron contents the viscosity values are more uniform in the homogenous liquid slag area. The viscosity values were lowest at high temperatures and highest at low temperatures.

Jan 1, 1998

By Sang-Beom Lee

For thermodynamic prediction, the deoxidation equilibrium of aluminum in Fe-36%Ni alloy was studied with a cold crucible under Ar gas atmosphere at 1773K. For the deoxidation reaction in liquid Fe-36%Ni base, i.e.: A12O3(s) = 2A1 + 3O The interaction parameters and the equilibrium constant between aluminum and oxygen in liquid Fe-36%Ni alloy are given in the following: eo Al = -3.8, roA1=0.9, eAl° = -6.4, rAl° = 700, rAIAIo = 3.1, roA1o = 833 within the composition range of [Al] < 1 mass%. The temperature dependence of the equilibrium constant was obtained in the range of 1773K < T < 1973K by using reported data and present results as follows: log KAo= 0.58-24463.7 / T The deoxidation equilibrium with aluminum in Fe-36%Ni could be thermodynamically well described in the range up [Al] < 1 mass% with first and second order interaction parameters as well as the equilibrium constant determined in this study.

Jan 1, 2002

By A. Kar

A mathematical model is presented for pure titaqium deposition from titanium tetrabromide on a stainless-steel (SS 304) substrate. Five three-dimensional, transient, and nonlinear partial differential equations are used to account for the diffusion of various species inside the deposition chamber and the thermal decomposition of titanium tetrabromide, titanium dibromide, and titanium monobromide at the surface of the substrate in order to determine the thickness of the titanium film deposited on the substrate. The effects of various process parameters on the deposition and shape of titanium films are examined, and under certain conditions, the deposited titanium films are found to have volcanic profiles.

Jan 1, 1992