Search Documents

By Richard S. Dennis

Acid recovery employs ion exchange (I-X) resin as separation media for inorganic acids from dissolved metallic salts by physical adsorption and without the use of chemicals. This technology has been used for years on spent etching and plating liquors to recover acid for reuse in the bath and to reduce waste acid neutralization costs. It is also used for electrolyte treatment to facilitate valuable metal recovery via acidity reduction. TETRA's ccrxr'" I-X contactor has been used successfully for acid separation from its metallic salt counterpart in a simple, continuous operating mode using strong base anion resins. Efficient separation is enhanced by acid reconcentration to nearly its original strength or as high as 14-20%. Continuous treatment also recovers heat to the tankhouse or bath and improves metal quality due to consistent acid quality. Conventional fixed bed ion exchange (I-X) systems are impractical for acid recovery because of complex control design and large resin inventories needed to process very low liquid-to-resin treatment ratios associated with strong acid concentrations.

Jan 1, 1996

By Jie Li, Shu Yang, Zhongliang Tian, Xun Hu, Yanqing Lai

The purity of the electrolyte has an important influence on the content of the impurities in electrodeposited silicon. In this paper, effects of electrolysis temperature, current density and the time on the concentrations of two important impurities: phosphorus and iron in the electrolyte were investigated during the purification of Na3AlF6-10%K2SiF6-AlF3 melt. It was observed that the concentrations of P and Fe in the electrolyte decreased with the electrolysis temperature, current density and the electrolysis time increasing. X-ray fluorescence (XRF) of the electrolyte shows that the concentrations of P and Fe decrease from 4.2ppmw to 1.3ppmw and 204.0ppmw to 42.6ppmw, respectively. The removal rates of P and Fe are 69.08% and 79.12% when the electrolysis was performed for the duration of 3 hours and at a current density of 20mA·cm-2 while the operating temperature was 1225K.

Jan 1, 2015

By P. Hajiani

Rare earth elements (REEs) are critical materials in many leading-edge technology products. However, REE separation outside China has remained a challenge in addressing environmental concerns of current production. The author has worked on a technique employing the emphasised variability in the electrophoretic mobility (μi) of REE for the purpose of REE separation. In continuation of the results presented in IMPC 2016 [1], this contribution summarizes the progress achieved in 2016 and 2017. The major goal was to increase the REEs concentration by a factor of 1000 and to attenuate the consequent drawbacks, specifically joule heating effect. Amphiprotic hydroxylic solvent was selected to replace water, which has a major impact on the complexation mechanism and buffer requirement. Non-aqueous media result in a significant drop in the specific molar conductivity of the electrolyte, whilst μi reduces several times only. Moreover, a quasi-steady state electrophoretic separation in conjunction with temperature gradient focusing is adapted to improve scalability.

By A. C. Wadhawan

In the present context of rapid industrialization, production of Lead-Zinc metals from low grade materials, residues and wastes can make substantial contribution to the supply of these metals in India. Recovery from secondary sources also plays an important role in conservation of mineral resources and lower power consumption. Conscious effort is therefore, required to increase the secondary metals which, besides saving in energy cost will also help in waste material management and keeping environment clean. The major thrust is, therefore, needed in this direction. During all these years, the Indian Lead- Zinc industry has made sustained efforts for recovery of metals from low grade ores and from metallurgical wastes and residues. The paper identifies the treatment of low grade ores by various technologies and techniques and the treatment of metallurgical residues and wastes generated during primary Lead and Zinc smelting in India. Some of the major achievements in past decade have also been elaborated in the paper. The strategies to be followed for continuing treatment of low grade ores and waste materials by adopting newer, environmental friendly technologies, in consonance with the rigid standards being adopted by most of the countries including India. have also been dealt with in the paper.

Jan 1, 1994

By Amy Nelson

In the electrolytic production of zinc, cobalt is removed from the zinc electrolyte by cementation with zinc dust prior to electrowinning. Although the thermodynamics for this reaction are favourable, kinetic barriers to cobalt reduction render the method almost useless in practice unless activators such as copper and antimony or arsenic are added. There is a large body of work studying the effect of these additives, yet the mechanism by which they act is still poorly understood. Even when the target conditions are met, zinc dust consumption is excessively high: satisfactory operation requires up to 300 times the stoichiometric amount of zinc dust. The objective of this work is three-fold: (1) to examine the effects of activators and elucidate the characteristics that make a good activator; (2) to identify new additives that could lead to a more efficient purification process; and (3) to test the new additives with synthetic and real electrolyte solutions. The present paper gives a status report on this project.

Jan 1, 1998

By V. V. Khristenko, V. I. Dubodelov, V. A. Seredenko, B. A. Kyryyevsky, H. V. Seredenko

"During the last decades investigators of many countries shows an increased interest to alloys which are characterized by miscibility gap in a liquid state. It is connected with essential possibilities of control of structurization in such alloys because of the melt at certain temperature parameters is · emulsion with disperse phase inclusions. These ensure essential influence ·on structurizations.The certain inclusions can play a role of lubrication ensuring ""wearless"" process. The sizes of inclusions of this phase can be rather large proportional to sizes of strengthening phase (up to 1000 nm). Other inclusions ensure process of strengthening of a main material. In this case requests to a dispersibility character of distribution and structure of such inclusions are much higher.The multicomponent alloys of system of copper - (Fe - Cr - C)- alloy concern to the number of advanced compositions. The copper alloys with structure of a type of a ""frozen emulsion"" in which strengthening phase· is a chromium pig-iron are characterized by high thermal stability in the extreme operating conditions. The mechanism of inclusions forming is emulsifying of a melt in miscibility gap at temperatures close to temperature of binodal under superimposition of external effects.The main complexity of producing of ware from such alloys is .a providing in their structure of necessary dispersible inclusions uniformly distributed all over the volume. Thanks to a selective action of electromagnetic fields on liquid phases with various electroconductivity relative velocity of phases is created and is regulated the ratio of their ""apparent"" specific gravity is changed. Excitation of pulsing force effects with the certain frequency on interphase surface allow actively to influence on process of a dispersion of a liquid metal medium."

Jan 1, 2000

By Xu-ling Chen, Qian Li, Yong-bin Yang, Zhao Jing, Tao Jiang, Guang-hui Li

"It is generally known that alkali metals are harmful to blast furnace production resulting in aggravating RDI of sinters, abnormal expansion of pellets, deteriorating blast furnace lining, etc. Sinters regarded as dominating burden of blast furnace are determined as the main source of alkali metals. In this study, the removal behavior of potassium and sodium oxides by pre-reduction sintering during the sintering process was studied. The removal ratio ofK20 and Na20 was greatly influenced by coke powder content, carbon species, coke powder adding ways, additive and so on. Under the conditions of carbon rate 12% and 5% dosage of CO supplied in the sintering process, the corresponding removal ratio ofK20, Na20 was 69.00% and 32.79%, and metallization ratio could reach 4.65%. This technology provided a novel process for reducing the content of alkali metals in sinters and dramatically improving the quality of blast furnace burden.IntroductionSinter is the main iron-bearing charge of blast furnace for iron-making in China, making up about 80% of the total burden; therefore, its quality has a significant influence on the quality of pig iron and blast furnace operation. Research and practice of numerous years prove that potassium and sodium coming from ores are brought into blast furnace and upgraded, which is one of the essential reasons that lead to blast furnace nodulation and influences its strength. Currently, effective flow sheet to remove potassium and sodium is weak magnetic separation-intensive magnetic separation-flotation [l], while iron ore concentrate is still ofhigh levels of potassium and sodium. As sintering process is also not effective to remove potassium and sodium, blast furnace in China is of high alkali burden, e.g. it reaches 5.6-6.2kg/tFe in Baotou iron making plant, which is greater than international tolerated level of2.55kgltFe [l]."

Jan 1, 2013

By A. R. G. Azevedo, G. C. Xavier

"The search for technological innovations in the Civil Construction takes as an objective the reduction of costs and increase of the productivity. However, these technologies demand analysis and studies of parameters of control that provide the quality of the products. With the intention of improve the knowledge on industrialized mortars used in mechanized projection machines, a characterization was done in the state anidro, fresh and hardening of three mortars, being each one of a State, Rio de Janeiro, Sao Paulo and Bahia. The tenors of water/ mortar was obtained through tests done in built environment, it varied from 0,17 to 0,26. From these results, the mortars were projected by his respective consistency, analyzing its compressive strength, and traction adherence resistance, in this way, the good performance of the revetments was provided.IntroductionThe market competitiveness of Construction has led companies to invest in construction processes and techniques in order to rationalize and optimize the buildings. Thus, changes emerged in coating system providing improvements in conventional materials and novel construction techniques, such as mortar industrialized and mechanized projection.Adopting projection equipment mortar is flagged as one of the solutions to reduce the interference of hand labor in construction, optimizing the performance of internal and external coatings, as well as streamline the production process and transportation, reducing lossesMaterials and deadline for execution of the casing(l)The process has been used due to its benefits, however, studies are necessary parameters for quality control of these mortars used in the projection to greater knowledge of mixing and market acceptance. It is therefore quite relevant information processing techniques available on the subject, as necessary to carry out research aiming at defining specific indicators of quality."

Jan 1, 2013

By H. Kandemir

An experimental study of the bacterial oxidation of naturally occurring high-purity sulphide minerals (FeS2, Fe1-xS, Cu5FeS4, ZnS) is presented using a mesophilic strain of T. ferrooxidans. As well as metal analyses and solution pH, partitioning of sulphide sulphur into elemental sulphur and sulphate has been monitored as a function of leach time. Partially oxidized sulphide substrates have been characterized, at regular time intervals, by X-ray diffraction methods and extracellular organic compounds reporting into leach solution .have been identified by thin layer -chromatography.

Jan 1, 1985

By Ting Liu, Qian Li, Peng Deng

The wastewater containing Hg2+ and Pb2+ does great harm to the environment and human bodies. Traditional wastewater treatment cannot fundamentally put a stop to heavy metals pollution for producing secondary pollution. In this paper, Hg2+ and Pb2+ in wastewater were removed and recovered by sulfide precipitation- flotation. Sodium sulfide was used as precipitant and butyl ammonium aerofloat was used as collector. Results indicated that Hg2+ and Pb2+ could be reduce to less than 0.03mg/L and 0.16mg/L respectively by both coprecipitation- floatation and fractional precipitation- floatation. In these two methods, fractional precipitation flotation could not only remove Hg2+ and Pb2+ from wastewater, but also could recover mercury and lead effectively. The infrared spectrograms showed that the adsorption between butyl ammonium aerofloat and mercury precipitate or lead precipitate is chemisorption.

Jan 1, 2015

By Satoshi Yamashita, Noboru Masuko

"Newly prepared bipolar membrane is promising to become a key material of an electrolyser for a production process of strong reducing solvent. This research is basic research for using bipolar membranes as electrolysers of reducing agents, Cr(II), TI(III) and V (II) on the laboratory scale. In this report, a bipolar membrane was tried with an electrolyser, reducing chromic chloride to chromous chloride. An analysis of mass balance demonstrates advantages of it over the former electrolyser equipped with an anion and/or. cation exchange membrane. The effects of current density and concentration of Cr(lll) on the reduction rate of Cr(II) and the current efficiency were examined No deterioration of the bipolar membrane resulted from the electrolytic reduction of Cr(III). IntroductionRecently, bipolar membrane that was the development subject for a long time in the industry of ion exchange membranes has met the stage of the practical application at last [l]. The expectation of the application to the hydrometallurgy field increases. We took up the manufacturing of the strong reducibility solvent as part of the application of bipolar membrane to hydrometallurgy technology. This laboratory has much experience in the electrolytic reduction of Cr (II) aqueous .solution such as chromous sulfateusing bipolar membrane were compared in theory to chromous chloride aqueous solution manufacturing of the strong reducibility solvent. The advantage of applying bipolar membrane by substituting ion exchange membrane is described, and the experimental result is reported."

Jan 1, 2000

By Jun Zhu, Jilai Xuel, Tao Li

"Coal gangue is industrial waste containing Al2O3 and SiO2 with great recycling and reuse values. This work is aimed at extracting Al2O3 content in the coal gangue by a process of carbonthermal reduction - alkaline leaching. The Al2O3 and SiO2 contents first became a mixture of SiC and Al2O3 in the process of carbonthermal reduction, and then Al2O3 was separated by leaching in NaOH solution, thus producing the sodium aluminate solution for Al(OH)3 precipitation. The products generated at various stages in the process were inspected using XRD and chemical analysis. The effects of parameters such as reduction temperature, carbon ratio, NaOH concentration, leaching time, leaching temperature, stirring speed, etc were investigated in details.IntroductionCoal gangue is an industrial residue resulted from the process of coal mining and washing, accounting for 100 - 150 kg with 1 ton raw coal mined. The existence of coal gangue in large quantities has become a serious problem for environment pollution. On the other hand, the chemical compositions of coal gangue are Si02 and Ah03 primarily. In China, the accumulation storage capacity of Ah03 in coal gangue is not less than 600 million ton at a rough estimate, which should be considered as an abundant second resource [1]. If the alumina can be recycling and reused effectively from coal gangue, it will not only reduce the imperilments caused by coal gangue, but also yield good economic returns.Generally, the processes of extracting Al2O3 from coal gangue can be divided into acid leaching (vitriol or hydrochloric acid) and alkaline leaching (mostly NaOH) [2]. The acid leaching processes have many problems, such as lower leaching ratio, corroding the equipments, recycling the spent acid hardly, etc. The primary matter of alkaline leaching process is silica dissolving with alumina, which brings perplexing desilication process, alumina loss seriously and higher energy consumption."

Jan 1, 2011

By M. M. Monte

A method for removing metallic mercury from contaminated tailing, using the flotation process, is described. In order to define some relevant parameters for the mercury flotation system, microflotation and electrophoretic mobility tests were carried out on (pure) metallic mercury in the presence of several surfactants. Based on the results obtained from fundamental studies a series of bench scale flotation experiments with mercury containing tailings from two wetland sites in Brasil were done. The results of microflotation tests with mercury showed that by using cetyl trimethyl ammonium bromide, an increase in mercury flotability is observed in the acid pH range, whereas in the presence of potassium oleate the highest mercury flotability was found in the alkaline pH region. The mercury flotability using potassium amyl xanthate was improved by the addition at sodium dithionate as an activator. The bench scale flotation tests with contaminated tailings from Poconé (brazilian wetland site) showed a recovery of 70% when sodium dithionate was used as activator and potassium amyl xanthate as collector. The resulting coefficient of separation is around 60%. However, the results of the flotation experiments with fine fractions from amalgamation tailings from Peixoto de Azevedo (brazilian wetland site) showed a low mercury recovery (32%).The results from this work suggest that since in the Poconé site tailings, the metallic mercury is not completely associated to the finer particles, the flotation process to recover the metallic mercury seems very promisor.

Jan 1, 1996

By A. Rosenfeld

The feasibility of applying laser induced optical emission spectroscopy to the high speed sorting of mixed alloy aluminum scrap is investigated. The basic spectroscopy for analysing aluminum alloys for the major alloying elements over their full concentration ranges is established. Materials handling issues are also described and the components of an overall sorting system are presented.

Jan 1, 1995

By Ray D. Peterson, Garry G. Blagg

"Molten aluminum is routinely transported hundreds of miles to customers in large ""over-the-road"" crucibles. This is especially common for aluminum recycling organizations handling scrap and by-products. Receiving the aluminum in a molten form can save the customer time and money since in-house melting costs and capital equipment can be avoided. Additionally, the alloy can be on specification and nearly ready to use for the casting operation.A number of transport crucible designs are currently in use. The specifics of each design are based on the needs of the customer, the equipment used at both the producer and the consumer, and over-the-road transportation constraints. Crucibles are designed to maximize carrying capacity, and refractory life while minimizing heat flow and dead weight. These conflicting demands place difficult design criteria on the design engineer.This paper will review the basic advantages and disadvantages associated with molten metal transport, give examples of the design restrictions and examine several types design of crucibles currently in use."

Jan 1, 2000

By Taner Kavas

The refractory bricks of a rotary cement furnace containing of alumina and magnesium chromite were studied in order to determine whether they could be used in the concrete production as aggregates. Three mortars were prepared by mixing 1 part cement, 3 part aggregate materials, 0.5 part water by weight and mechanical, chemical, thermomechanical and microstructural characteristics were evaluated. The compressive and bending strength of samples were determined after 2 and 28 days curing. Resistance to chemicals were established by calculating the weight gain of mortars stored in 2 % HCl solution for 1 h and 24 h. Thermomechanical characteristics were determined by measuring the compressive strength of heat treated specimens at temperatures of 400 °C, 600 °C and 800 °C. Consequently, magnesium chromite containing waste brick aggregates have given the best results.

Jan 1, 2006

By Ivo André

Sorption of copper ions from aqueous solutions by dried biomass of the aquatic plant Potamogeton luscens was studied at laboratory scale. The aquatic plant was collected in water resources in Brazil, washed, dried at 60°C and ground in a bladed mixer. Sorption experiments were conducted in agitated flasks and in a packed bed column. Maximum copper removal was obtained between pH 5.0 and 6.6 when copper was present in the ionic form Cu'. Sorption followed the Langmuir isotherm with saturation attained at 35 mg/g. Free energy of sorption was found, to be of the order of -25 kJ/mol. Sorption kinetics data were better described by a second order reaction and rate constants were calculated in 0.030 1/(min.mg) for - 4.0 mm particles and 0.081 1/(min.mg) for - 0.59 mm particles. Removal of metal ions in a packed bed column showed that Potamogeton luscens biomass can be used in several sorption/dessorption cycles. After sorbent saturation, copper ions can be recovered from the loaded biomass by elution-with H2SO4, solution. Main mechanism responsible for heavy metal uptake was found to be ion exchange. Results are discussed in terms of the surface properties of the biomaterial, solution chemistry of copper ions and thermodynamics parameters.

Jan 1, 1995

By A. N. Aposhian

The electronics industry generates tin/lead bearing by-products that can be recycled for their metal value. This paper will cover the processes used to recycle these tin/lead bearing byproducts from the plating, circuit-board fabrication and assembly industries. Though these processes are well known to the companies who do the recycling, few outside the industry including the generators of the by-products, understand the processes or needs of the industry. This paper will give a broad overview of these processes, and describe the services provided by this industry. The paper will also touch upon the future of the recycling industry, including the legislative and environmental push for the elimination of lead from electronics.

Jan 1, 2000

By Samantha Moodley, Rauf Hurman Eric, Cevat Kucukkaragoz, Aditya Kale

"Two titania slags, rutile and synthetic rutile were chlorinated with petroleum coke and CO in a small bubbling fluidized bed reactor. The study aims to identify differences in chlorination mechanism, compare conversion rates, blowover and the chlorination of impurities for the various titania feedstocks at different temperatures.Chlorination rates were highest at 1000ºC; rutile chlorination significantly increases as temperature increases from 800ºC to 1000ºC. At 1000ºC, synthetic rutile had the highest chlorination conversion rate; this was followed by Slag B which in turn was more reactive than Slag A and rutile. The mechanism for slag, synthetic rutile (SR) and rutile chlorination differs. Synthetic rutile feed is porous, providing a larger surface area for the chlorination reaction, hence the highest conversion rates was attained. Titania slag becomes porous with the initial chlorination of FeO and MnO whilst rutile remains solid. As the porosity of slag particles increases so does its tendency to be elutriated. Ti2O3 is oxidized within the early stages of chlorination during the chlorination of FeO and MnO. Ti2O3 not oxidized is then rapidly chlorinated.IntroductionTitanium dioxide (TiO2) is the most common compound of titanium, about 95 - 98% of extracted titanium minerals is processed into TiO2 white pigment [1]. Two processing routes exist for the production of TiO2 pigments, i.e., sulphate and chloride based processes. In the chloride process, titania feedstock is fed to a fluidized bed reactor together with reductant and chlorine gas. A temperature of 1000 - 1300ºC is maintained in the reaction zone and apart from silica, zirconia, uranium and thorium, virtually all the metal oxides in the feed are converted to their respective chlorides [2]. Chlorine is recovered and recycled back to the reactor."

Jan 1, 2012

By Chu Yong Cheng

Synergists can be used in solvent extraction to improve the selectivity of extractants for metals. Research work carried out by the SX group at the AJ Parker Cooperative Research Centre for Hydrometallurgy / CSIRO Minerals has shown that the pH isotherm of nickel with Versatic 10 was significantly lowered by the addition of the synergist Acorga CLX50. The paper discusses how this synergistic shift can be used to alleviate a gypsum formation problem at Bulong nickel laterite operation in Western Australia. Metal pH isotherms were obtained with Versatic 10 and synergist CLX50 using synthetic leach solutions. In terms of pH50, the extraction order of the metals with 0.5 M Versatic 10 alone was Cu > Zn > Ni > Co > Mn > Ca > Mg, whilst the extraction order with Versatic 10 and 20% by volume CLX50 was Cu > Ni Zn > Co > Mn > Ca > Mg with the pH50 (Mn-Co) significantlyincreased. This is significant because the isotherms of valuable metals Ni, Cu, Co and Zn shift more towards low pH than those of the waste metals Mn, Mg and Ca, resulting in a possible good separation of Ni, Cu, Co and Zn from Mn, Mg and Ca. The use of intermediate precipitation, solids/liquid separation and re-leach in the three Western Australian nickel plants make these processes complicated and costly in capital and operation. The research work carried by the SX groupat the AJ Parker Centre has led to the development of direct SX (DSX) processes to recover nickel and cobalt from leach solutions using synergistic organic systems. Semi-continuous tests with a BHP Billiton pilot plant leach solution showed that Ni and Co together with Zn and Cu were separated from the major impurities, Mn, Mg, Ca, and Cl, in the first SX circuit. The co-extracted impurities were easily scrubbed. After stripping, Ni and Co together with Zn and Cu were concentrated, resulting in a much smaller second SX circuit in the down stream processes.

Jan 1, 2003