Search Documents

By Yuanbo Zhang, Mingjun Rao, Weiguang Tian, Huimin Tang, Guanghui Li, Lei Ye, Guoshen Liang, Zhiwei Peng, Foquan Gu, Tao Jiang

The amount of slag produced from a typical ferronickel smelting pro- cess is 4 to 6 times that of the metal product, and handling this slag is a huge challenge to the ferronickel industry. The feasibility of a technological route for preparing refractory materials from a ferronickel slag was verified in this study. Based on the thermodynamics analysis, the effect of the sintering temperature on the properties of refractory material from the slag was studied in the presence of magnesia. The results of thermodynamics calculation showed that the reaction of MgO with SiO generated forsterite and enstatite, whereas the reaction between 2 MgO and Fe O /Al O produced corresponding magnesia spinels. The experi- 2 3 2 3 mental results showed that a refractory material with refractoriness of 1580 °C, bulk density of 2.88 g/cm3, compressive strength of 106.9 MPa, and apparent porosityof 5.8%was obtained under the conditions ofmagnesia addition of 15 wt %, sintering temperature of 1350 °C and sintering time of 3 h. With increasing sintering temperature, the bulk density and the compressive strength of refractory material increased but the apparent porosity decreased, mainly attributed to the formation of the liquid phase which promoted the densification of the refractory material. (cid:1) (cid:1) (cid:1)

Mar 1, 2018

By Guray Kaya

Boron minerals are widely employed in various fields such as ceramic, glass, cement, metallurgy, etc. Although boron deposits of the world are limited, the production level of boron-based products is continuously increased. Turkiye possesses approximately 73 % of total world boron resources. Etibor Kirka Borax Company of Turkiye produces tincal concentrates and borax pentahydrates. During such productions considerable amounts of concentration and derivation wastes appear. Having considered the increased rate of production it is quite obvious that the level of relevant wastes will also be raised. With this study it was aimed to utilize these wastes in roof tile and brick bodies and to convert them into a form environmentally and human friendly. Newly produced products were undergone to several standard tests for the determination of their shrinkage, water absorption, strength values and coloring parameters. Additionally, micro structural studies were conducted.

Jan 1, 2006

By N. L. Piret, E. N. Mounsey

Ausmelt technology is successfully used to process primary and secondary materials to produce lead in large-scale commercial operations and to meet stringent environmental standards. The development and commercial data covering these applications and the results with respect to metallurgical, cost and environmental performance are reviewed in commercial operations. A new smelter is scheduled for commissioning in 2000 at Korea Zinc's Onsan site to process lead fume and other secondary materials to produce 50,000 tonnes per annum of lead bullion. The unique features of Ausmelt technology also allow for the efficient processing of polymetallic concentrates and secondary materials, particularly copper and lead, through the effective separation of these elements into metal, slag and fume species. This capability has been successfully demonstrated at a commercial scale and the results and implications for the industry are discussed.

Jan 1, 2000

By M. H. Erten

Most of the fourteen workable coal seams in the State of Missouri have high ash and sulfur levels and need beneficiation in order to meet customer and Environmental Protection Agency requirements. If proper ash and sulfur removal methods can be designed, more Missouri coals will be mined and used within the state. One of the main objectives of this research is to investigate the possibility of removal of sulfur of Missouri coals by conventional beneficiation methods.

Jan 1, 1982

By Michael Meyer

In the past shredder fluff was discarded in landfills, but shrinking landfill space and the partly hazardous content of the fluff as well as its caloric value, all resulted in efforts to turn this waste problem into a an energy resource. In order to produce a fuel, the inorganic compounds have to be removed. Extensive analyses and particle size measurements were made on fluff from various shredder. For optimal separation all particles are reduced to a uniform, relatively small size. In a subsequent combined - screening and air classification - process, successful separation into organic and inorganic fractions is achieved. The inorganic fraction is treated in a heavy media or an eddy-current separator to recover the valuable metals, while the organic fraction is now suitable for thermal processing, such as fluidized bed gasification and using the resulting carbon as a chemical reagent.

Jan 1, 1995

By John Gordon

Rare earth elements (REE) required in modern technological products are found in shale rocks above and below coal seams. Often during the process of mining coal, shale rock adjacent to the seam inadvertently is removed then diverted to landfill sites. Ecologically sound and potentially economic methods of extracting the REEs from these landfills are proposed. Methods include utilizing geomemembrane barrier beneath the landfill site, ion exchanging with moderate pH, slightly acidic, sodium chloride solutions. Sodium hydroxide is utilized to precipitate the REE-hydroxides subsequently converted to REE-chlorides with suitable amount of hydrochloric acid. All acid and base streams are co-produced with efficient membrane/electrolysis technology. Concentrated-REE chlorides are transported tocentralized solventextraction facilities for isolation and purification. Solvent extraction processes also employ the methodology of using co-produced acid/base streams. This paper details minimization of environmental impacts and maximizing economics to produce valuable REEs while increasing the economics of coal mining.

Mar 1, 2018

By M. I. Kalashnikova

In hydrometallurgical technological flowsheets several methods of target components removal from solution are used. One of these methods is non-ferrous metals removal in the form of rich selective or collective concentrates. In the present work pyrometallugical mattes, thiosulphate containing solutions and pulps, iron powder with elemental sulphur and calcium sulphate were used as the precipitator. It was shown that depending on precipitator compound and process parameters non-ferrous metals precipitate from solution in the different forms with varying content of components including Ni3S2, NiS, Ni3S4, NiS2, (Ni,Co)S2, CuS; Cu1,765S; Cu1,97S.

Jan 1, 2006

By Guy Deschênes

In spite of the wide use of lead compounds to enhance cyanidation of free milling sulphide-bearing gold ores, an industrial control method was only implemented four years ago. This study presents the results of the investigation that led to the development of the on-line control technology. Two free milling sulphide-bearing gold ores and high purity minerals were used to develop and test the concept. The first ore contains 2.8 g/t Au, 6.2% pyrrhotite, 2.1% pyrite 0.6 % arsenopyrite, 0.1% chalcopyrite and 0.1% organic carbon. The second ore contains 10.4 g/t Au, 3.2% pyrite, 0.8% pyrrhotite and 0.38% chalcopyrite. The first ore showed a much higher oxidation rate in the pre-leach than the second one and consumed seven times more cyanide. A relation between the formation of thiosulphate and thiocyanate and the additions of lead nitrate were quantified. The ?reducing power?, a titration with permanganate, predominantly determines the concentration of thiosulphate and thiocyanate in cyanide solution. The relation between the reducing power and the addition of lead nitrate at various concentrations of pyrrhotite and chalcopyrite in the ores was established, providing a monitor/control strategy for lead nitrate addition.

Jan 1, 2006

By Sungdon Kim, Chuljoo Kim, Joonsoo Kim, Hosung Yoon

"This study was performed to establish the optimum leaching condition through the experiments for the oxidized roasting followed by leaching of fluorocarbonate rare earth mineral (bastnasite) using sulfuric acid, and to establish the optimum condition for the recovery of cerium by ion- sieve method from the leached solution of bastnasite. The optimum conditions for the sulfuric acid leaching by the oxidizing roasting of bastnasite concentrates are that the roasting temperature is 550 -600 °C, the roasting time is 2 hrs, the concentration of sulfuric acid is 6N, the leaching temperature is S0°C and the leaching time is 3 hrs. At this time, the leaching yield of total rare earth oxides in the leaching of bastnasite concentrates is about 91%. When cerium is recovered by ion-sieve method from the solution obtained by the sulfuric acid leaching of the roasted bastnasite, the optimum conditions are that the TREO(total rare earth oxide) of leached solution is below 70 g/l, the flow rate of leached solution is 9.6 ml/min and the ratio of height to diameter of resin packed in column is above 9. In these conditions, the recovery of cerium of yield 85% and purity 96% is possible.IntroductionThe rare earths are generally called to Lanthanides, which are totally 17 elements including Scandium of atomic number 21 and Yttrium of atomic number 39 in addition to 1 S elements from Lanthanum of atomic number 57 to Lutetium of atomic number 71. Since the separation to each element is very difficult because of their similar chemical properties, the rare earths were used as the mixed rare earths and the mischmetal without separating to each element. However, the high purity rare earths are recently produced commercially to each element so that they are used as the materials for high tech. industry such as electric and electronic materials, catalysts, optical materials, special alloy and 8Uperconductive materials, and their consumption is rapidly increasing. Therefore, the purpose of this study is firstly to prepare leached solution by using the series of process of the oxidation-roasting and leaching by sulfuric acid. Next, second purpose is the separation and recovery of cerium by ion-sieve method."

Jan 1, 1998

By A. Rikos, G. Pantazopoulos, A. Vazdirvanidis, A. Toulfatzis

In this study, the mechanical properties of an annealed CuZn36 rolled brass alloy with 0.2 mm thickness with respect to anisotropy expressed in terms of plastic strain ratio measurements (r-values, normal and planar anisotropy) are related with the development of specific rolling and recrystallization texture components obtained by EBSD. Anisotropic behaviour is primarily controlled by the crystallographic texture and constitutes an indicator of multi-axial mechanical behaviour, affecting directly the drawability and sheet metal formability. Microstructure examination employing optical and Scanning Electron Microscopy of tensile specimens are performed in order to investigate the emergent damage mechanisms in relation to the texture and structure evolution of the final product.

Mar 1, 2017

By C. A. Landolt

Inco pioneered the use of tonnage oxygen in non ferrous metallurgy when it commissioned the first .industrial oxygen flash smelting process for the treatment of copper concentrates in the early fifties. This technological innovation was followed by other applications of technical oxygen. Inco is currently implementing a Sulfur Dioxide Abatement Program designed to reduce S02 emissions from the smelter by 60% in 1994. The new flowsheet includes new equipment for the oxygen flash smelting of Cu-Ni concentrates and for flash conversion of chalcocite. Oxygen smelting and converting technology will lead to a substantial decrease in use of fossil fuels and to generation of high strength S02 off gases suitable for efficient fixation in a new acid plant.

Jan 1, 1992

By L. B. Tsymbulov

Sulphide melts formed in the course of smelting of nickel and copper-nickel feed (matte) actually are sulphide-metallic melts since sulphur contained in the melts is in deficiency with respect to metals. The level of metallization is rather relevant feature of sulphide melts and is widely used in calculating material and heat balances for pyrometallurgical processes. Despite of the above parameter? importance, the investigators have no single opinion on what should be understood under metallization level and the method of its determination. In the present study we present the results of our own experimental and theoretical researches that have allowed determination of some mechanisms of sulphide melts? crystallization. Based on the mechanisms revealed new scientifically justified approach has been offered for determining level of metallization of the components present in sulphide melts. It has been demonstrated that sulphur distribution between the melts is substantially different from generally accepted concept.

Jan 1, 2006

By Min Xiaobo

As for treatment of zinc-containing wastewater, traditional SRB (Sulfate Reducing Bacteria) process was used, however, there exist two defects, like toxicity of heavy metal ions and high effluent COD (Chemical Oxygen Demand) value. In this study, a new technique, called ISIS process (Immobilized SRB sludge beads with Inner cohesive carbon Source), in which SRB sludge is embedded in carrier of PVA (Polyvinyl Alcohol) with carbon source that adsorbed on certain material, is put forward for the first time to overcome the two defects existing in traditional SRB process. Furthermore, it has been shown that compared to traditional SRB process, ISIS process increases average zinc removal rate up 30%, average sulfate reduction rate up20%, and decrease average effluent COD value to meet discharge standards. If activated carbon is selected for carbon source adsorption and fixing material, and PVA for immobilization material, the zinc removal rate can reach above 98% under the conditions of 35 and pH 6. Meanwhile, the mechanism of zinc removal has been determinated according to the results from SEM (Scanning Electronic Microscope) and XRD (X-Ray Diffraction).

Jan 1, 2006

By T. Shoji

"The human history is characterized by social development based on mineral and energy resources, and many conflicts to take the resources by power. This is shown by not only world wars but also many local conflicts as well as international supremacy.IntroductionThe world population after B. C. 10000, which is summarized in several papers, is approximated by four straight lines on a semilogarithmic diagram as shown in Figure 1 [l]. The annual rates of increasing are 0.0041, 0.071, 0.53, and 1.85 % from the old and young periods. The boundaries among four periods are approximately B. C. 4600, AD. 1670, and 1930. The start of the second period seems to correspond to the beginning of agriculture and cattle breeding. Precisely speaking, the usage of natural energy resources such as woods and domestic animals already began, but is inferred to have become common after the age. The third and fourth periods are characterized by the common usage of coal and oil, respectivety. Not only energy resources but also mineral resources including gold, copper, iron and others are also important for the human history.Mineral and energy resources have supported the development of the .human civilization, and have caused many conflicts because of this reason. Every day newspapers report conflicts, such as Chechnya, East Timor and Ache. We can easily point out the facts that the conflicts closely relate to mineral and energy resources. Groznyj, Capital of Chechnya, is located on the western margin of Caspian oil field. Many mineral deposits occur in Kavkaz Mountains running south of Chechnya. Subsea oil fields occur in Timor Gap located between East Timor and Australia. Ache is also one of oil fields in Indonesia. It is very difficult to state present conflicts independently of a political view of point. For this reason let us try to historically review the relation between mineral and energy resources and international domination and conflicts [2] based on many papers [3]."

Jan 1, 2000

By Joel F. Flurnerfelt

Molten Al and Al alloys containing si, Mn, Ti, and y have been lanced with nitrogen-bearing gases. These lancing experiments provided the means for observing what phases form during exposure to nitrogen-bearing gases for finite periods of time, <2 minutes, at high temperatures, >1290oC. The experiments were conducted in sn induction heated drop tube furnace apparatus. The overall premise of these experiments was to select those Al alloys and gas compositions that show promise of forming secondary dispersoid phases, particularly AIN, in the Al matrix. The alloys selected will be atomized using gas atomization reaction synthesis (GARS) using the most favorable conditions. In this case, the chosen Al alloy will be atomized with a nitrogen-bearing gas, such that the Al and gaseous nitrogen species react to form a dispersoid phase within each powder particle. The powder particles that result from this "aggressive" GARS-process would be essentially Al metal-matrix composites within a uniform distribution of dispersoids. To date, only high-purity Al has been atomized using a mild GARS reaction. This work is funded by the Materials Science Division of DOE-BES under contract number W-7405-Eng-82.

Jan 1, 1996

By Yue Gong, ChuanJie Cai, Jing Chen, Shaobo Zheng, Huigai Li

"MnS-AlN duplex precipitates were successfully extracted from electrical steel slabs by means of non-aqueous solution electrolysis. The three-dimensional duplex morphology became visible using emission scanning electron microscope (SEM) JSM-6700F and energy dispersive spectroscopy (EDS). The precipitation sequence of MnS and AlN in the hot process can be predicted via the three-dimensional duplex morphology. Thermodynamic calculations were carried out on account of the chemical compositions of the steel studied in this paper. The results verified that AlN nucleated on MnS, which precipitated earlier during cooling process of electrical steel. Based on the results, the material compositions and rolling temperature can be adjusted to modify their precipitation timing and morphology. This is conducive to the growth of MnS-AlN duplex precipitates and reducing the obstacles to grain growth. Finally the magnetic property of electrical steel would be improved.IntroductionElectrical steel is a kind of ferrosilicon soft magnetic alloys with extremely low carbon content. It is mainly used in the manufacture of motors, generators, transformers and varieties of teleco=unications equipment. Non-oriented electrical steel requires isotropic high magnetic induction and low iron loss [l, 2]. Precipitates in steel have a great influence on its performance [3]. On the one hand, the indirect effect of precipitates on magnetic properties is to restrict grain growth in high temperature annealing process. On the other hand, the direct effect is pinning of domain wall motion, which leads to increased hysteresis loss."

Jan 1, 2013

By Andre Thess, Jurij Kolesnikov, Christian Karcher

"During the motion of molten metal under external non-homogeneous magnetic field the induced electric currents produce Lorentz body forces in the opposite direction to the flow, causing deformation of velocity profile, vortical structures, and adding a pressure drop across the magnetic field. The same Lorentz force acts on the magnet system. We analyse these phenomena in metallurgy, namely, at molten metal pumping, stirring, continuous casting, and in contactless Lorentz force flowmeter (LFF). Experiments with liquid metal alloy, including direct measurements of Lorentz forces, velocities, and flow structure visualization were conducted. Based on this study the industrial prototypes of LFF systems were designed, built, and tested in a secondary aluminium production. A molten metal flow at high temperature (700°C-850°C) can be effectively measured. The LFF technique method allows measuring precisely the volumetric and mass flow rates linked with Lorentz force, and the mass accumulated within production process.IntroductionThe present work demonstrates the development of a non-contact electromagnetic system for measurement of a liquid metal flow. Our approach embodies the Lorentz force velocimetry [1-6] technique which is physically based on a measurement of the force acting on an external magnet system the field of which interacts with the flow. This force is exactly equal to the braking Lorentz force induced in a flowing conducting fluid. In what follows a measurement system based on the Lorentz force velocimetry principle. For monitoring and controlling the production process it is desirable to measure continuously the mean velocity of the liquid metal in order to deduce the mass-flux and volume-flux from it. The form and dimensions of the magnet system are in agreement with geometry of the operating channel. We consider here a version of magnet systems in a composition of permanent magnets.The LFF possesses a number of advantages which make it attractive for the measurement of flows in hot and aggressive melts. The relation between the measured force and the desired volumetric flow rate is often linear (for closed channel or at a constant liquid metal level in open channel). For the converting of the measured force into volumetric and mass flow rate we should know the calibration factor. The calibration factor is independent of the viscosity and density of the liquid metal and depends only on the magnetic field magnitude, the electrical conductivity of the liquid metal and the geometry of the channel in which the liquid metal flows. In aluminium production, for instance, there exists a number of standard alloy compositions having welldefined conductivities for which the calibration factors can thus be tabulated. We consider below consistently effects in liquid metals arising under influencing magnetic field, construction principle of LFF and measurements of metal flows at industrial conditions."

Jan 1, 2011

By Tracy Morris, Weldon Read, Luis Navarro

"Bismuth is a recognized contaminant in the electrolytic refining of copper that can render many cathodes to be outside ASTM standards and unsuitable for copper rod and other downstream products if not carefully controlled. This paper portrays the performance of Molecular Recognition Technology (MRT) for bismuth removal at the Amarillo Copper Refinery (ACR) and describes how the highly selectivity gel has been successfully used to achieve good bismuth removal and how many pit falls and draw backs have been overcome.IntroductionASARCO operates one of the largest copper refineries in the world at Amarillo, Texas. The main feed for this refinery is produced at the Hayden smelter in Arizona. During the operation of this smelter a variety of metals are carried as impurities in the copper anodes because of the diversity of concentrates and residue products used as raw materials in the smelter feed mix. Even though the impurities are concentrated enough to be detected at the smelter, it is difficult to remove them completely. A simple way to control impurities at the smelter is to minimize the addition of material with a high concentration of impurities to the charge in order to reduce the output of this metal species. All this leads us to have a ""refinery problem"" [1,2,3]."

Jan 1, 2012

By Qingzhu Li

The adsorption process of Pb2+ from aqueous solutions by spent grains modified with Imol/L NaCI solution was investigated. The effects of solution pH, contact time, adsorbent concentration, initial Pb2+ concentration, particle size on Pb2+removal were also studied. The initial adsorption process was rapid and 90.35% of Pb2+ adsorption occurred within 30 min. The absorption equilibrium was obtained at 4h. When pH was 5.5, Pb2+ concentration in aqueous solutions decreased from the initial content of 20 mg/L to 0.0 I mg/L after 5 hours by application of IOg/L adsorbent at 25?C, Pb2+ removal efficiency reached up to 99.95% and the Pb2+ remaining in aqueous solutions was under China Sanitary Standard for Drinking Water (GB5749-85). Adsorption data fitted well with Lanf+muir and Freundlich models. However,Langmuir isotherm model was better to descnbe Pb- adsorplion than Freundhch model, mdlcatmg that the applicability of monolayer coverage of Pb2+ on the surface of adsorbent.

Jan 1, 2008

By Gary A. Wickham

In the zinc industry, this past decade has seen both prosperity and depression. Significant changes have occurred throughout the world in mining, smelting, refining, and marketing. This paper will review many of the industrywide changes of recent years and the potential impact for 1990s. In addition to an historical review of supply and demand are discussion of technology considerations for zinc and zinc based products, effects of geographical shifting of markets, and projections for the 1990s.

Jan 1, 1990