Search Documents

By Chi-Ming Chang

Alloy powders are commonly used in the purification of zinc sulfate solutions for use in standard electrowinning practice. The primary goal of this research was to study the use of zinc-lead alloys for similar reactions in the galvanic stripping of impurities from organic solutions. The effects of various parameters on the electrochemical behavior of commercially produced zinc-lead alloy powders were determined. A qualitative evaluation and summary of the influence of the more pertinent parameters on iron removal from di-(2-ethylhexyl) phosphoric acid (D2EHPA) by galvanic stripping is given. Water concentration, oxygen content and reaction temperature were the principal factors affecting the reaction rate and process efficiency. Activation energies were also calculated and indicated that the reaction changes from chemical to diffusion control .with increasing temperature in the range of 35" to 45°C. The results showed that zinc-lead alloy gave faster reaction rates with less sensitivity to process variables than SHG zinc as a reducing agent for galvanic stripping. The role of lead could be as cathodic sites for the reaction which enhances the zinc dissolution or anodic half reaction. The morphology of the zinc-lead alloy surfaces, before and after the reactions, supports this assumption.

Jan 1, 1998

By D. L. Stewart

"Melt loss is usually one of the highest individual cost items in the operation of ah ingot casting facility. While melt loss and the resulting cost for the entire facility is usually well known (at least via standard cost accounting), dross generation and melt loss for individual unit operations within the plant are usually not known. Thus, the financial impact of various practices, alloys and scrap types is not known. Development of an accurate, relatively low-cost technique for measurement of melt loss at commercial scale would aid in understanding melt loss for existing units, as well as evaluation of the melt loss impact of alternate processes.This paper will describe a methodology developed at Alcoa for accurate and inexpensive measurement of melt loss at commercial scale. The methodology has been used to evaluate the impact of scrap type, melting practices, and dross treatment technology on melt loss."

Jan 1, 2000

By Toru Taniguchi

In the Mitsubishi smelting furnace, copper concentrate, silica sand and water granulated slag from the converting furnace are injected through the process lances, together with oxygen enriched air, into the melt. Because bath smelting is used, the rates of particles/melt and gas/melt reactions are high enough and therefore tine grinding of the solid materials is' not necessary. Among these reactions, the dissolution rate of silica sand is the slowest and limits the overall reactions in the smelting furnace. Information on the dissolution rate of silica sand plays an important role for design of a new furnace. Theoretical calculations of the dissolution rate .of silica particles have been reported elsewhere. The authors conducted cold model experiments and could verify the calculation. In this paper, the dependence of dissolution rates of particles on the gas blowing rate, particle size and solid penetration depth in the bath is discussed.

Jan 1, 2002

By Beatryz C. Mendes, Henrique de Paula Santos, Kléos M. L. Cesar, Eduardo Antônio G. Marques, Maurício Paulo F. Fontes, Rita de Cássia S. S. Alvarenga

Inadequate discard of industrial solid waste is a risk to human health and to the environment. Aiming at softening environmental damage caused by deposition on soil of an ink residue, from washing of printers used in carton box packages, it is intended to incorporate this residue into soil-cement bricks. The residue has other use potentialities such as in screeds, pavement parts, fertilizer, paints, etc. However, to explore these potentialities it is fundamental to assess the risks that the several forms of use of this residue can cause. For such, in this work the chemical analysis of the residue was performed in order to know its main chemical compounds, in addition to its characteristics of leaching and solubilization. The chemical composition assay showed traces of some heavy metals such as Pb, Cd, Cr, Zn, Al and Cu, although the residue-generating company uses ink labeled as heavy metals free. Among the elements analyzed in leaching and solubilization, some had concentration above the limit allowed by The Brazilian Codes. This code is based on CFR—Title 40—Protection of Environment—Part 260–265—Harzardous waste management. Therefore, it is suggested that the residue has a limited use to avoid contamination of ground water.

Mar 1, 2017

By R. Nilsson

In the present work the sulphide capacities of Ca0-Mn0-Si0, ternary slags have been measured in the temperature range 1798 - 1873 K by equilibrating the slag with a gas-mixture containing CO, CO,, SO, and Ar. The results are compared with the data reported in literature. A theoretical model has been developed in the present work where the sulphide capacity is expressed as a function of the slag composition and temperature. The model enables the estimation of sulphide capacities of complex slags with a knowledge of the capacities of simpler systems.

Jan 1, 1994

By N. J. Tannyan

Laboratory bath smelting tests were conducted to determine the feasibility of smelting nickel- copper concentrate directly to a low iron matte in one step. Concentrate, air/oxygen and a silica flux were fed to a matte-slag bath kept in MgO crucibles at 1300°C. Various oxygen enrichments and smelting rates were used to maintain 0.5 to 2 wt"10 iron in the product matte. The slag losses are comparable to those obtained under similar industrial conditions. Due to the highly oxidizing conditions required to produce mattes with low iron contents, it is not recommended to target iron contents below about 2% in the matte. The specific bath smelting rates were equal to or higher than those in various industrial bath smelting processes.

Jan 1, 2003

By N. J. Tannyan

Laboratory bath smelting tests were conducted to determine the feasibility of smelting nickel- copper concentrate directly to a low iron matte in one step. Concentrate, air/oxygen and a silica flux were fed to a matte-slag bath kept in MgO crucibles at I 300°C. Various oxygen enrichments and smelting rates were used to maintain 0.5 to 2 wt% iron in the product matte. The slag losses are comparable to those obtained under similar industrial conditions. Due to the highly oxidizing conditions required to produce mattes with low iron contents, it is not recommended to target iron contents below about 2% in the matte. The specific bath smelting rates were equal to or higher than those in various industrial bath smelting processes.

Jan 1, 2003

By Giuseppe Granata

An innovative process using titanium tetrachloride (TiCl4) gas as reactant has shown successfully to obtain titanium through electro-winning of TiCl2 formed in-situ on titanium cathode. The process involves a continuous feed of TiCl4 gas reacting onto a titanium cathode immersed in a molten salt (NaCl-KCl), whereby in-situ formation of titanium dichloride (TiCl2) through a disproportion reaction. Simultaneously, the TiCl2, thus in-situ formed in the molten salt media, has been reacted into chlorine gas and titanium, the latest electrodeposited on the titanium cathode by electrowinning. The reaction kinetic of this innovative process was investigated in terms of TiCl2 in-situ formation rate and galvanostatic electrodeposition rate, where, in particular, the effect of operating variables such as TiCl4 partial pressure and flow rate, as well as temperature and galvanic potential applied was investigated.

Jan 1, 2014

By Kumar Ganesan

Elevated mercury levels are expected in aged gold mine tailings due to residual mercury from the amalgamation process, The fate of mercury in tailings is not well understood, Its potential health risk depends mainly on the degree to which mercury is mobile in soil. Mercury is re-moved from soil by evaporation, plant uptake, microbial activities, leaching, and other physico-chemical processes. In this research the amount of mercury lost by evaporation was evaluated. Several aged gold mine tailings in Montana were sampled for total mercury and its flux into the atmosphere. Mercury levels in tailings were higher than the general background levels in most sites. The mercury levels in some cases were as high as 10,000 ug/g. The field measurements using flux chambers indicated a wide range of mercury flux from aged gold mine tailings. The mercury flux ranged from 0-11,000 ng/m2/hr. The mercury loss by evaporation helps rid the soil of mercury but the mercury vapor then will participate in the atmospheric mercury cycle, The low solubility of elemental mercury in water helps to minimize mercury leaching from tailings, however, conversion of elemental mercury to more soluble forms by bio-geo-chemical processes can enhance its mobility posing increased health risk.

Jan 1, 2003

By Leah Penner, Thomas J. Ruth, Paul Schaffer, François Benard, Edouard Asselin, Stefan K. Zeisler, Thomas J. Morley

"This paper details the electrodeposition of metallic molybdenum from an aqueous, acetateelectrolyte containing molybdate ions. The deposition is carried out in a highly concentrated (up to I 0 M) acetate bath in the presence of a very low concentration of bone glue (60 µg/L). The molybdenum metal deposits are up to 20 µm thick and adherent. The deposits were characterized by XRD and XPS analysis. The deposition process is very inefficient, as up to 99% of the current is used to generate hydrogen during electrolysis. The effect of acetate concentration, pH, additives and current on the deposition efficiency and physical properties of the molybdenum deposit were investigated and optimized to obtain smooth, adherent coatings.IntroductionMolybdenum has increased thermal and wear resistance properties that are often utilized in material coatings [I]. These coatings are most often manufactured by sintering, pressing or spraying molybdenum powder at elevated temperatures, as a substitute method for standard metallurgical practices, such as electroplating [2, 3]. The lack of reports describing molybdenum deposition is most likely due to the highly oxophilic nature of molybdenum and the stability of its oxides, especially in water. Previous attempts to electrochemically reduce molybdenum from molybdate (Mool·) ions to molybdenum metal have reported the production of either a poorly adherent mixed oxide [4-6], or a thin(< 0.1 µm) metallic film [7-9]. Thick metallic molybdenum is capable of being co-deposited with one of the iron-group metals (Ni [10], Co [11] and Fe [12]) to produce an alloy [13, 14]. These alloys, however, may not be suitable for applications requiring pure molybdenum as they usually contain less than 50% molybdenum (often less than 30%)."

Jan 1, 2012

By Helmut Antrekowitsch

Nowadays nearly the half of the world zinc production is used for galvanizing. After their life span most of the galvanized products return as scrap to the steel mill During the steel process the zinc is collected in the flue dust It is astonishing to notice that between 40 and 50 % of the zinc produced is brought into the steel processing cycle by the coated scrap while only 3 to 5 % of the zinc production can be covered by the recycling of the zinc-bearing steel mill dusts. Responsible for this worse ratio is the fact that the established recycling technologies suffer from high energy consumption, low zinc yields, halogen problems and hardly any iron recovery. A development of new or an optimization of current recycling procedures for the dusts is unalterable because of increasing zinc amounts in these residues and the rising costs for the disposal. Different pyrometallurgical recycling technologies are tested in rotary kilns and vertical retorts at the Department of Nonferrous Metallurgy, University of Leoben, Austria. Various reducing agents from carbon monoxide to hydrogen and combinations are used. The results should make it possible to draw conclusions that allow an economical and ecological judgement of the different varieties. The goal is to support the affected industry to increase the low recycling rate and prevent a loss of high zinc values in the steel industry filter dusts.

Jan 1, 2003

By Yuanbo Zhang, Zhixiong You, Guanghui Li, Peidan Wen, Tao Jiang

Sn-bearing iron ore containing small amount of Zn, Pb and As is one of the typical complex polymetallic ores in China. This kind of ore is not extensively utilized due to the complicated relationships between iron and other associated nonferrous metal minerals. Excessive contents of these elements would adversely affect the metallurgical operation as well as the quality of steel products. In this study, reduction behavior of Sn was detailedly investigated using H2 or mixed H2/CO as reductant. The results revealed Sn volatilization was improved in the presence of H2 than individual CO/CO2 atmosphere. Simultaneous volatilization of these elements was realized by roasting under weak H2/CO reducing potential, and metallization reduction was advantageous for further Zn volitilization. A metallic pellet (DRI) with Fe metallization greater than 90%, residual Sn, Zn, Pb and As content of 0.054%, 0.012%, 0.0045% and 0.09% was prepared via a simulated reducing gas of coal gasification.

Jan 1, 2015

By J. Rastas

The recovery of lead, silver and gold from existing and potential zinc process residues using a sulfidization-flotation method was investigated on a laboratory scale. The following residues were tested: neutral leach residue, high acid leach residue, and hematite residues. The sulfidization of lead and silver is carried out at low pH by the addition of a stoichiometric amount of sulfide at a controlled rate. To increase the particle size of the sulfides, seeding with synthetic lead and silver sulfides -is employed. The flotation is carried out at pH 2-4 using low pH-collectors such as dithiophosphates and dithiophosphinates. Special attention must be paid to the role of oxygen in the conditioning stage. The effect of different parameters on both the sulfidization and the flotation has been evaluated. Recoveries of 85-90, 90-95 and about 80 % were obtained for lead, silver and gold, respectively. Typically, concentrates containing 50-60 % lead, 3-5 kg/t silver and 10-15 git gold were produced.

Jan 1, 1990

By Xueming Lv

The rotary kiln-electric furnace (RKEF) process is the main method for producing ferronickel from nickel laterite ore. However, this process is energy intensive as it involves several high temperature steps. Therefore, a novel process is proposed to directly produce ferronickel from nickel laterite ore by semi-molten reduction, which is expected to be realized in a rotary hearth furnace (RHF). The RHF process is able to shorten the flow sheet, decrease the reaction temperature as well as reduce energy consumption. In this study, the influence of basicity on reduction of nickel laterite ore was investigated. The results showed that it is possible to produce the ferronickel nugget directly at 1400 °C when the quaternary basicity [(mCaO + mMgO)/(mSiO2 + mAl2O3)] was fixed at 0.60. Under this experimental condition, the grade and the recovery ratio of nickel reached 11.53% and 98.59%, and the grade and recovery ratio of Fe were 84.16% and 68.72%, respectively.

By J. M. Zhuang

Lignosulfonates, by-products of the sulfite pulping process, have been utilized in a process [1, 2] to treat acidic rock drainage (ARD). This process is referred to as the LignorTM process. In the present study, lignosulfonates were found to protect lime from developing an external surface coating, and hence to favor its dissociation. Further, the addition of lignosulfonates to ARD solutions increased the clotting and settling rate of the formed sludge. The capability of lignosulfonates to form stable metal-lignin complexes makes them very useful in retaining metal ions and thus improving the long term stability of the sludge against leaching. The LignorTM process involves metal chelation with lignosulfonates, ARD neutralization by lime to about pH 7, pH adjustment with caustic soda to 9.4 ? 9.6, air oxidation to lower the pH to a desired level, and addition of a minimum amount of FeCl3 for further removal of dissolved metals. The LignorTM process removes all concerned metals (especially Al and Mn) from the ARD of the Britannia Mine (located at Britannia Beach, British Columbia, Canada) to a level lower than the limits of the BC Regulations. Compared with the high density sludge (HDS) process, the LignorTM process has many advantages, such as considerable savings in lime consumption, greatly reduced sludge volume, and improved sludge stability.

Jan 1, 2003

By F. Qian

Direct impingement of molten metal baths by a gas jet is commonly encountered in such processes as BOF and electric arc furnace steelmaking. Shape and local fluid mechanics in the impinging region is important because it determines the interaction of the metal pool with the surroundings. Goal of the present work is to characterize and understand the interfaces at the impinging region. Using a physical model consisting of water/corn oil and water/kerosene as surrogates for metal/slag, interface shapes for slag-gas, slag-metal and metal-gas are investigated. Influence of transport properties of the two liquids on the shape and flow fields are also experimentally determined under various impinging jet conditions, namely jet momentum and jet height. The viscosity of the slag layer (corn oil or kerosene) has the most significant effect on the interface shape and the induced flow fields. The interface shapes were measured both photographically and by using a surface- tracking resistance probe. The limiting condition at which the jet breaks through the corn oil or kerosene layer and reaches the water layer was determined experimentally

Jan 1, 1994

By Ze-Qiang Xie, Bai-hui Wang, Feng Chen, Ling-zhi Yang, Yu-feng Guo

In this paper, based on the big data in steelmaking process, equation about the relationship between steel composition (especially the oxygen content) and the element yield is established by using mathematical analysis method to analyze the factors influencing yield. Meanwhile, combining the alloy yield data-base that were established based on self-learning of historical data and computer technology in steelmaking process, a method of yield prediction of alloy elements is studied. To provide support for this method, alloying elements yield prediction software is developed to realize the rapid and intuitive site operation guidance, and to realize the precise control of dosage of alloy material.

Mar 1, 2017

Lead blast furnace water-jacket stability was investigated by examining samples from the Port Pirie Lead Smelter. The compositions of the phases formed in the samples were analysed using Scanning Electron Microscopy (SEM) and Electron Probe X-ray Microanalyser (EPMA). Phase equilibria analysis and thermodynamic modelling was undertaken using FactSage with latest thermodynamic database for the slag/matte/metal/speiss/solids multi-component Cu2O–PbO–ZnO– Al2O3–CaO–MgO–FeO–Fe2O3–SiO2–S major and As–Bi–Sb–Sn–Ag–Au minor elements system. Results indicated that the stability of the water-jacket steel wall without freeze-lining is influenced by formation of the complex Fe-rich speiss phase at critical As concentrations. The integrity of the furnace walls with freeze-lining is critically dependent of the stability of the oxide-based freeze-lining which is dependent on various factors including most critical one—the proportion of solids determined by the slag chemistry and fluxing. Thermodynamic modelling of the lead blast furnace operation indicated limiting thermochemical conditions for the water-jacket stability. Factors and controls critical to the water-jackets integrity are discussed.

By Fathi Habashi

The recovery of uranium from wet process phosphoric acid was applied on industrial scale in the 1940&apos;s by using octylpyrophosphoric acid as an extractant. Later, more efficient reagents were used, e.g., di(2-ethylhexyl) phosphoric acid and actylphenyl phosphoric acid. In the 1970&apos;s the rare earths in Kola phosphate were recovered in Finland and recently (1997) in Norway using HNO, as a leaching agent and di(2-ethylhexyl) phosphoric acid as solvent. It was demonstrated later on laboratory scale that both uranium and rare earths could be extracted from the rock by tributyl phosphate but at different pH values provided that the rock is leached with nitric or hydrochloric acids instead of the commonly used sulfuric. This new concept opens the way to the possibility of treating phosphate rock by in-situ, dump, or vat leaching for the recovery of phosphate values as well as uranium and the rare earths. Another solvent extraction process is used industrially for the purification of phosphoric acid using butyl and amyl alcohols.

Jan 1, 1998

By Baoxiang Zhang, Jing Zhang

"As extruded Mg-9Zn-0.6Zr-2Er magnesium alloys were hot-rolled at 400°C, followed by solution treatment at 400 °c for 1. 5h and artificial aging at 200°C for 10h. Microstructures and tensile mechanical properties of the alloys after hot rolling, solution and aging treatment were examined respectively. Optical micrographs of the as-rolled and as-solution alloys showed fine grain structures, due to the formation of Er-and Zn-bearing compounds at grain boundaries which obviously improved the thermal stability of the alloy. Yield strength as high as about 335 MPa was obtained for the as-rolled alloy, showing that the mechanical properties of the alloy was greatly benefit from the grain refinement and dynamic precipitation of fine MgZn2 during hot rolling. Due to solution heat treatment, vast majority of the Mg-Zn phases dissolved into the matrix, and precipitated out again as fine dispersoid during the subsequent aging, resulting in an enhanced aging-hardening effect.IntroductionWith high specific strength and low density, magnesium alloy has stimulated significant interest for the applications in microelectronics, aerospace and automobile industries. Due to its HCP structure, magnesium alloys exhibit relatively poor strength and ductility. Great efforts have been made to improve the properties of magnesium alloys.Thermo-mechanical processing which combined with subsequent heat treatment can strengthen magnesium alloys due to the strain-hardening mechanism, homogeneous distribution of second particles and grain refinement [1, 2]. However, commercial wrought magnesium alloys have high tendency of grain growth at high temperature due to lack of effective solutions to stabilize the microstructure [3, 4, and 6]. But Magnesium-RE alloys containing high rare earth were reported to have remarkable thermal-stability, Rare earth (RE), such as Y, Nd, Yb, Gd, Ce, were known to form second-phase particles that have higher thermal stability combining with Zn and matrix in Mg[12-17]."

Jan 1, 2012