Search Documents

By Yang Hong-ying, Yu Juan

Electrochemical behavior of natural chalcopyrite in electrolyte solution at pH value of 6.97 was studied by cyclic voltammetry, X-ray photoelectron spectroscopy and electrochemical impedance spectroscopy. The results showed that the electrochemical processes occurred on electrode surface were controlled mainly by the growth of sulfur species at lower applied potentials (<0.35Vvs.SHE), and the oxidative dissolution of sulfur species and the hydroxylation of iron at higher applied potential (>0.45V). The EIS spectra of oxide product layers could be illustrated by the equivalent circuit of Re(QdlRct(QfRf)), and the degree of hydrophilicity for chalcopyrite was higher when the value of charge transfer resistance Rct. was greater. The optimum potential range for the floatation of chalcopyrite in collectorless solution at pH value of 6.97 was between OCP (0.165V) and 0.35V.`

Jan 1, 2015

By S. Tandon

Equilibria studies of selenium distribution for sodium-borate slags were initiated at 1473k under reducing condition as a function of slag composition and alloy composition. The Se distribution coefficient (% Se in slag/% Se in metal) increased from 0.4 to 2.9 with increase in basicity (0.53 to 0.86) for Cu-0.446% Se alloy. However, the results are not very useful from industrial application viewpoint. Therefore, in order to improve the distribution of Se, CaO (10% to 50%) was added to the sodium-borate slag of basicity 0.864. On addition of 502 CaO, the distribution coefficient increased roughly by 100% for slag composition - 44.5% Borax, 22.2% Na2C03, 33.3% CaO and Cu-0.44677 Se alloy. Further, the value of this distribution coefficient has been found to increase by an additional 80% on addition of 20% CaF2 to the above slag for all Cu-Se alloy compositions. Also with increase in initial concentration of Se, the distribution coefficient has been noted to increase.

Jan 1, 1992

By Zhang Yongzhu

Sulfoxides are one kind of extractants for precious metals. The structure, the coordination reaction, the extraction behaviour and the precious metals complexes of sulfoxides are summarized. The differences between sulfides, sulfoxides and sulphones are also discussed.

Jan 1, 1992

By K. H. Bech, S. T. Johansen

"The mass transfer at fluid-fluid interfaces due to turbulent agitation is investigated theoretically. In particular a theory is derived for interface stresses due to interface energy and surface renewal. This theory indicates that surface renewal may take place if the geometry is sufficiently large and if surface tension is sufficiently low.By using a model for a typical turbulent structure we compute the interface mass transfer for a stressless interface and a fully interface. Results for the general situation is not presently available. The computed results are used to derive analytical expressions for the mass transfer based on turbulent kinetic energy and free stream turbulent length scales.One important application of the theory is the mass transfer at the electrolyte side of the bath-metal interface in the Hall-Heroult process. For this process we show that mass transfer should be expected to be of the rigid surface type."

Jan 1, 1999

By Y. Fukunaka, M. Niinae, E. Kusaka, T. Kuzuya, R. Ishii

"Samarium oxalattr particles was precipitated in oxalic acid aqueous solution from samarium-loaded D2EHPA solution emulsified with a conventional impeller. The calculated fractional precipitation of samarium oxalate was reasonably compared with the value determined by chemical analysis. Morphological variation of oxalate precipitate particles was then examined with H2C2O4 concentration in aqueous solution, Sm(III) and D2EHPA concentrations in organic phase. The needle-like precipitate was identified as Sm2(C2O4)3 10H2O by XRD. Precipitates obtained at higher H2C2O4· or Sm(III) concentration greatly decreased the length of major axis of precipitate, while those at higher D2EHPA concentration increased it. The oxalate was further precipitated under ultrasonic irradiation. However, the morphological variation caused by theses processing variables was not so evident under ultrasonic irradiation as in an impeller or shaking mixer.IntroductionThe materials processing of the rare earth elements must be reviewed from the scope of industrial ecology, since they have the potential applications of magnetic materials as well as secondary battery in developing programs of the electric vehicle. The technological trend to develop the electric vehicle may greatly influence the concept of materials processing, since the global· environmental problem must accommodate with the sustainable development for mankind. The recycle design must be a key issue in the materials science and engineering.Solvent extraction provides a unique separation technology -in this sense. Doyle (1)(2) reported the integrating solvent extraction with processing of advanced ceramic materials, whose chemical composition and microstructure must be precisely controlled. In her paper, the higher productivity inherent to the present process superior to hydrolyzing metal alkoxides was emphasized. Oxalic acid has been used as precipitant for rare earth purification process, since rare earth oxalate has a very small solubility in water and can be easily decomposed to oxide. It is thus suitable for precipitation stripping agent in cationic exchange type extracting system (i.e. D2EHPA, VA-10, PC-88A and so on)."

Jan 1, 2000

By C. E. M. Meskers, U. Boin

"The increasing use of coated magnesium in consumer products results in creation of coated Mg scrap during product manufacture and after End-of-Life product treatment. Currently this material is generally not recycled, leaving a material resource unused. Closure of the magnesium cycle in a sustainable manner is necessary. In order to do so, the effect of coatings on the recycling process has to be quantified, predicted and minimized. For this purpose metrics have been developed, based on first principles supported by detailed understanding of the recycling process. The developed 3D metric enables quantitative assessment of the recyclability and links coating design, product design and recycling to each other in a visual manner. The parameters that form the metric can be measured and predicted, hence an engineering basis for Design for Sustainability of coated magnesium is provided.IntroductionEvery product progresses through the four phases of the product life cycle depicted by figure 1. In each phase residues are created. Their amount and composition is largely determined by the complex material combinations created/invented during product design in the manufacture phase. Compared to the ideal cycle the magnesium cycle is far from closed (fig. 2). Most noticeable is absence of the link between the EoL phase and raw materials production. A closed cycle only exists for class 1 scrap, which goes from the product manufacture phase directly to production from industrial material and returns to the manufacture phase as magnesium alloys. The four problematic streams are marked by ???. Coated semi-products are present in two of the four residues, namely in rejects and collected scrap. When these semi-products are recycled the amount and composition of the dross and salt slag residue is affected as well.During product design selection of the coating takes place, fixing the coating character¬istics and properties from this moment on for the rest of its life cycle. The choices made in the manufacturing phase are therefore critically linked to the recyclability of coated semi-products as well as the sustainability of the magnesium cycle as a whole. Sustainable closed life cycles, in which the quality of materials is preserved and residue creation and resource depletion are minimized, can be attained by selecting the appropriate alternative during product design. To realize this the effect of design choices on the life cycle and more specific the recycling process has to be known and quantified."

Jan 1, 2008

By Patricio Barrios

In February 1996, ATLANTIC, COPPER completed the construction of a Project for Expansion and Environmental Improvements in its Smelter and Electrolytic Refinery located in Huelva. Following the expansion, the new operating concept is based on the simultaneous blowing of two converters, while increasing throughput in the Flash Furnace up to the level required to deliver matte to both converters. While the production level planned with the Project.(270,000 MTPY of copper from concentrates) was reached the following June, work since then has been carried out to optimize the new equipment .and to develop a new operating shedule. This paper describes operational experiences from the start up of the Expansion Project, difficulties encountered and operating improvements introduced, which have allow an increase of production levels up to 300,000 MTPY of copper.

Jan 1, 1998

By L. L. Ludwig, S. E. James, B. L. Motycka

Significant modifications to the electrolytic zinc plant operated by Big River Zinc Corporation were made at the end of the 1990's resulting in increased capacity and improved efficiencies. A new cell room, with the innovative use of acid-resistant concrete cells and a modern ventilation system, was installed to raise the capacity from 80,000 tonne/y to 106,000 tonne/y of finished zinc. Improvements to the leaching section include the conversion from a single to a two-step process, with associated equipment changes, to improve the quality of the residues produced. Another key change is the construction of a facility to allow the use of zinc oxides from secondary sources as a feed to the plant. This paper describes these improvements and the current operations.

Jan 1, 2000

By R. G. Reddy

To better understand the behavior of bacterial-mineral interfacial reactions, a thermodynamic model based on the- studies of bacteria adhesion on mineral surfaces has been evaluated. The bacteria adhesion to the mineral surface would be increased by l &apos; d1;1creasing the change in Gibbs free energy of adhesion and it would be reduced if the change in Gibbs free energy of adhesion of the system is increased. From the combination -of Young&apos;s equation and equation of state, the change in Gibbs free energy of adhesion -for bacterium-mineral system- was calculated. Influence of liquid surface tension, mineral surface tension on the change in Gibbs free energy of adhesion and consequently bacteria behavior on mineral systems- has been discussed.

Jan 1, 1991

By M. J. Collins

A hydrometallurgical process has been tested at the Sherritt Research Centre for separation of zinc, lead, copper and precious metal values from the zinc oxide fume leach residue stockpiled at the HBM&S operations in Flin Flon, Manitoba. Zinc is found primarily as zinc femte and sphalerite in the residue, lead as lead sulphate and jarosite, and copper as sulphide and jarositic compounds. Gypsum and siliceous gangue are significant diluents. The separation process includes hot acid, atmospheric and reducing (sulphur dioxide) leaching; zinc, copper and lead flotation; and atmospheric iron removal steps. Zinc is recovered to a high strength zinc sulphate solution and to a zinc sulphide concentrate suitable for feed to a roaster or to a zinc pressure leach plant; lead to a high grade lead sulphate concentrate suitable for feed to a lead smelter, and copper to a high grade copper sulphide concentrate suitable for feed to a copper smelter. Precious metals are divided between the zinc, lead and copper concentrates.

Jan 1, 1993

By Peijia Lin

Wheat straw was chemically modified by alkaline treatment followed by succinylation and sodium carbonate treatment for the use of cadmium and nickel adsorbent. The adsorption efficiency was calculated in different conditions. The experimental parameters were solution pH, adsorbent dosage, contact time and initial metal concentrations. The biosorbent was analysed by FTIR (Fourier- Transform Infrared Spectroscopy) to investigate the changes of surface functional group. The maximum adsorption percentages of cadmium (>99%) and nickel (>98%) were achieved using 5 g/L adsorbent with 50 mg/L initial metal concentrations. The adsorption kinetic study showed that the reaction was pseudo-second order kinetics and the adsorption isotherm was well fit by the Langmuir adsorption model. The dynamic column study indicates that modified adsorbent has a better adsorption capacity towards cadmium than nickel.

By Yong Zhao, Yan-hui Sun

Behaviors and evolutions of MgO·Al2O3 in non-oriented silicon steel during calcium treatment were investigated by thermodynamic calculations and high-temperature experiments. MgO·Al2O3 inclusions were the main type of inclusions before calcium treatment, which is also confirmed by the stability diagram of MgO/MgO·Al2O3/Al2O3 from thermodynamic calculations. After calcium treatment, the majority of original MgO·Al2O3 inclusions were mainly modified to CaO-MgO-Al2O3 system inclusions, this would be beneficial to improve castability and product quality of silicon steel. But there was no modification happening to some MgO·Al2O3 spinels which were directly surrounded by CaS inclusions. The content of Al2O3 occasionally existed a sudden increase besides a common decrease in the product layer of CaO·MgO·Al2O3. Then the evolution mechanisms of MgO·Al2O3 inclusions were proposed in present work. Thus, Al/Mg atom ratio had a significant influence on the modification of MgO·Al2O3 spinel.

Jan 1, 2016

By Veneta Groudeva

A pyritic ore containing zinc, lead and copper as? the relevant primary sulfide minerals, .as well as gold and silver finely disseminated in the sulfide matrix, was? leached in percolation columns. Each column contained 30 kg of ore crushed to minus 10 mm. Firstly, zinc and copper were efficiently leached by means of chemolithothrophic bacteria? in acidic sulfate bearing medium. Zinc was leached more rapidly than copper but the final extractions of these metals were similar (about 75% in 300 days). A part of the galena was oxidized to the. insoluble lead sulfate during the leaching. The pyr:ite was, however, relatively slightly attacked. The ore was then leached by means of FeC11 - HCl solutions both in the presence and in the absence of bacteria to solubilize the lead. The chemolithotrophic bacteria grew in media containing both chloride and sulfat~ ions and maintained a high ferric to ferrous ion ratio in the percoiating solutions. The chemical leaching was, however, more efficient since ft was possible to carry it out at higher chloride ion concentrations. About 10% of the lead was leached in this way in 90 days. Finally, the ore was leached by thiourea in the presence of a gold-oxidant (oxone) to extract the gold and silver. Over 60% of the gold and over 55% of the silver were extracted from the ore in 150 days, while. the extractions of these precious metals from an untreated ore sample were lower than 25%.

Jan 1, 1991

By Steve Johnston, Mowafak Al-Jassim, Fei Yan, Omar Sidelkheir, Alain Blosse, Katherine Zaunbrecher

"Imaging techniques are applied to multi-crystalline silicon wafers and solar cells throughout the production process. Photoluminescence imaging, both band-to-band and defect-band, is used to characterize defects and wafer quality at all process steps. These steps include bricks sawn from ingots, wafer sawing, cleaning and texturing, emitter diffusion, edge isolation and glass removal, anti-reflective coating/passivation, and metallization of finished cells. Bricks, wafers, and cells can be imaged at a rate commensurate with in-line measurement, giving spatial information to characterize quality and defect content. Photoluminescence images on silicon bricks can be correlated to lifetime measured by photoconductive decay and could be used for high-resolution characterization of material before wafers are cut. The defect areas in as-cut wafers are compared to imaging results from electroluminescence and lock-in thermography, and cell parameters of near-neighbor finished cells, showing correlations to efficiency, open-circuit voltage, and short-circuit current.IntroductionImaging techniques can rapidly characterize material quality and defect density. Photoluminescence (PL) imaging can be applied to silicon from the brick level to all wafer process steps [1-8]. At the brick level, material thickness allows for measurement and correlation to lifetime where surface recombination effects are minimized [6, 7]. At the as-cut wafer level where thin unpassivated wafers prevent accurate lifetime assessment due to surfaces, defects can still be categorized and quantified to predict finished cell performance [3-5]. Defect regions can be identified by recombination-limited band-to-band PL or by defect-band emission [9-12]."

Jan 1, 2012

By A. Block-Bolten

Copper concentrates from northern Peru contain large amounts of arsenic and antimony in the form of sulfosalts like enargite, tennantite and tetrahedrite. These impurities affect up to 30% of Peruvian copper production. Under the sponsorship of the Instituto Geologico Minero y Metalurgico in Lima a project to separate copper from arsenic without pollution of the environment is being carried out at the National University of Trujillo in Peru. The U.N.T. process is unique in the respect of using .low melting salts as solvents, and sulfides of metals with high cation potential as destructors of the complex sulfosalt molecules. Laboratory scale experiments have given encouraging results but interesting and difficult problems developed on scale-up. The process is pyro-hydrometal-lurgical and under certain circumstances its economics are promising.

Jan 1, 1981

By Keizo Uematsu, Satoshi Tanaka, Nozomu Uchida, Anze Shui, Joaquin Lira, Cyril Lavelle, Midori Saito, Thierry Poirier

"Dispersed and flocculated alumina (non-spherical particles) slurries were prepared by pH controlling with HCL Spray-drying of these resulted in dimpled granules with a smooth surface and high density, and spherical granules with rough surface and low-density, respectively. Detailed characterization on granules and their compacts includes: SEM observation, density measuring (mercury porosimetry and Archimedes's Principle) and liquid immersion optical microscopy. Compaction of these granules originated a larger particles rearrangement in the samples made with the spherical granules than with the dimpled granules. This was verified through the orientation of alumina particles, which was pronounced in the compact made with the former granules.IntroductionOn immersing a ceramic powder in water, the surface usually acquires a charge by interaction with ionic species in solution. The charge is affected by pH and the electrolyte concentration of the water. 1 The dispersion in a slurry is achieved through the interaction of charges on the particle surface with the media. In the ceramic processing, especially in the process of casting, the dispersion of slurry has been one of the most important topics studied for many years. Recently the attention is paid on its role in the pressing. The granule characteristics are governed by the dispersion state of slurry. Takahashi et al2 , Tsubaki et al3 and Walker et al4 showed that the granules from dispersed slurry were dimpled and of high density, while granules from flocculated slurry were spherical and of low density. This variation in the granules characteristics should have a marked effect on the structure of compact.This paper presents the influence of the dispersion state of alumina slurry on the granules characteristics and also on the internal structure of compacts. Different dispersion states were elaborated by adjusting pH of the slurry. In this method, the particles are dispersed or flocculated only by the effect of surface charging, and thus some secondary effect such as the steric hindrance from an electrolyte dispersant is avoided. The characteristics of granules and compacts are examined with SEM, density measurements by mercury porosimetry and by Archimedes's Principle and liquid immersion optical microscopy. This novel microscopy provides various important information on packing structure of particles, such as their orientation. 5"

Jan 1, 2000

By A. McLean, Y. Uchida, M. Iwase, M. Myochin, K. Wiikimoto

"Phase diagrams of FeO-containing ternary systems could be derived from experimental data for the activities of FeO. The systems investigated are CaO-CaF2-FeO, SrO-SrF2-FeO; BaO-BaF2-FeO, CaO-CaCl2-FeO, SrO-SrC12-FeO, BaO-BaC12-FeO, CaO-A12O3-FeO and BaO-SiO2-FeO.IntroductionThe importance of phase diagram cannot be overemphasized. In a book, ""Alloy Phase Equilibria""[l], the author, Professor A Prince, states, ""A metallurgist has been defined as a person who thinks in terms of phase diagram"". Whether one accepts this statement or not, it is self-evident that an ability to interpret phase equilibria is essential to the professional metallurgists.The physical chemistry studies of iron and steelmaking process often require phase diagrams of FeO-containing slags. Iso-thermal section of the phase· diagrams of such systems can be derived from experimental data for chemical potentials of FeO. Due to the recent developments in the area of solid state electrochemistry, rapid determinations of the FeO activities have become possible. The present paper is aimed at documenting the derivation of the phase diagrams of FeO containing slags.Experimental AspectsAn electrochemical method incorporating stabilized zirconia can be used for the measurements of the activities of FeO in various slags and fluxes[2]. For the details of the experimental technique, reference should be made to reference 2"

Jan 1, 2000

By Francis Vanbellen

In Union Minière&apos;s Hoboken smelter and refinery for complex non-ferrous materials, the treatment of recycling products, containing precious metals, occupies a dominant place. For all feed materials, the first step, prior to their treatment, is to classify them in order toselect an accurate and economical procedure for sampling as well as to dispatch them to the optimal process scheme. More than 150 different procedures for sampling are commonly used. The most important ones are briefly discussed in the paper. Precious metals bearing recycling materials vary widely with respect to their physical aspect, their chemical composition and the value of their precious metal content. All these parameters are taken into consideration to select the most appropriate process among the multiple possibilities of Union Minière&apos;s flexible integrated flow-sheet. Different stages of the operations as well as the main flow-sheets are described.

Jan 1, 1995

By Raymond E. Healy

Circuit samples from the HBMS concentrator were assayed for l5elements, and image analysis was done to determine the modal quantities, grain size distributions and liberations of the minerals. Material balancing was done on these data to determine distributions of the minerals in each concentrator stream. The ore was mined during the waning phase of mining and is diluted with backfilled copper smelter slag. The mill feed grades 1.0 wt% Cu and 1.8 wt% Zn. The slag silicate phases contain approximately 1.5 wt% Cu and 6.5 wt% Zn; therefore the Cu and Zn head grades due to chalcopyrite and sphalerite, are only 0.9 wt% Cu and 1.2 wt% Zn, respectively. The recovery of Cu in the Cu-concentrate (Cu-conc.) is only 77.5 %, whereas that of chalcopyrite is 89.2 %. Similarly, the recovery of Zn in the Zn-concentrate (Zn-conc.) is only 40.2 %, whereas that of sphalerite is 71.0 %. The slag accounts for approximately 60 % of the Cu, and 85 % of the Zn in the tailings. The main loss of chalcopyrite is as unliberated grains to the tailings, and the main loss of sphalerite is as free grains to the Cu-concentrate and as unliberated grains to the Cu-concentrate and tailings. Approximately 85 % of the chalcopyrite and sphalerite lost to the tailings. accounting for 8 % and 10 % of the respective minerals in the concentrator feed, occur as middling and sub-middling grains. Extremely fine regrinding would be required to liberate these minerals.

Jan 1, 1989

By M. Z. Mubarok

Effect of single addition of a lignin-based biopolymer additive, DP 2782, at various dosages as well as in combination with thiourea on cathode polarization during copper deposition was investigated by performing potentiodynamic and galvanostatic measurements using a potentiostat. The result of electrochemical measurements was compared with the behaviour of cathode deposition with glue and thiourea additives. Surface micro-appearance of the copper deposit after 1 h galvanostatic scan under current density of 330 A/m2 and various additive type and dosage was evaluated by scanning electron microscopy (SEM) examination. It was found that the addition of 2.5 mg/l biopolymer gave sufficiently polarizing effect of copper deposition. SEM examination of the cathode surface after galvanostatic scan revealed that the combination of the biopolymer with thiourea (2.5 and 3.5 mg/l) resulted in a compact deposit which is comparable with that resulted from the test with glue and thiourea.