Search Documents

By E. Legault-Seguin

The current industrial practice in the processing of nickeliferous laterites involves the precipitation and releaching of Ni and Co to allow separation from the major impurities of Mn, Mg and Ca. A direct solvent extraction process has significant advantages over this practice, which suffers from difficult and costly precipitation steps, lower recovery and inherently complex flowsheets. The present investigation involves the examination of Cyanex 272, Cyanex 301 and Cyanex 302 as extractants for the direct extraction of Ni and Co from major impurities associated with laterite leaching, i.e. Mn, Mg and Ca. For Co extraction, Cyanex 301 and Cyanex 302 are superior to Cyanex 272, because they are able to selectively separate Co from Mn, Mg and Ca. Cyanex 272 offers complete extraction of Co from Ni and Ca, but Mn and Mg pose difficulty. Ni can only be extracted selectively with Cyanex 301, thus another extractant selective for Ni, such as Versatic 10 or Cyanex 301, is needed to recover Ni if Cyanex 302 or Cyanex 272 is used for the initial extraction.

Jan 1, 2004

By Fernanda Margarido

Recovery of metals contained in the electrode materials of batteries was studied considering an integrated recycling process constituted by physical and chemical operations. The physical treatment included the shredding of the spent batteries, followed by a wet sieving operation of the fragmented material. The physical behavior of Ni-Cd and Zn-Mn based (alkaline and saline) system batteries was studied and compared. In that sense, shredding operation was performed and the sieving of shredded fractions was accomplished to evaluate the efficiency of the separation of electrodes and scrap. For Ni-Cd batteries the loss of electrode material with the supra fraction (scrap) after the shredding operation was lesser than the Zn-Mn batteries. Especially for saline-type batteries, the electrode attached to the scrap was substantial leading to important losses. This difference can be explained by the composition of the case materials and the internal physical constitution of the electrodes. The wet sieving studies carried out allowed optimizing the separation of the electrode fine fractions from the scrap materials through the analysis of selectivity Cd/Fe or Zn/Fe. For Ni-Cd batteries, maximum selectivity was achieved for the granulometry of 1.4 mm, while for alkaline and saline systems best selectivity were obtained at 2.8 mm and 5.6 mm, respectively. This process allowed the recovery of about 70% of electrodes for Ni-Cd and alkaline systems, and 50% for saline batteries, with less than 5% of scrap as contaminant. This physical step can be considered as a pre-treatment of this type of waste material envisaging its valorization by chemical treatment, as improves the concentration of the elements of interest and decreases the iron content.

Jan 1, 2006

By M. Cassir

"The unique properties of molten carbonates offer a large scope of applications in the field of energy. In effect, these molten salts are in the center of chemical and electrochemical reactions involving carbon and carbonaceous species, carbon dioxide and carbon monoxide, significant for energy generation or even for the production of fuels. Moreover, such media have also an oxidative character; they dissolve molecular oxygen and oxygen reduced species, O 2-, O22- and hypothetically o-, which may have an important role in waste treatments, homogeneous catalysis and synthesis of oxides. In this presentation, an overview will be given on the principal physicochemical properties of molten carbonates, before focusing on their main known application, the molten carbonate fuel cell (MCFC). Progress in other new fuel cells applications will also be analyzed, such as direct carbon fuel cell (DCFC), hybrid carbon fuel cell (HDCFC) and composite high-temperature fuel cells combining the features of MCFC and solid oxide fuel cell (SOFC). Afterwards, membranes for the separation and capture of C02 will be reviewed. Finally, other topics, as the oxidative coupling of methane in molten carbonates, will be briefly mentioned.IntroductionIn the thirty past years, the molten carbonate science and advances have been mainly dedicated to the understanding and optimization of the molten carbonate fuel cell (MCFC), which is still a major issue in the heart of a new vision of energy development. More recently, new topics related to other kinds of fuel cells (DCFC, composite SOFC/MCFC systems) and C02 capture have emerged and are concentrating important research and technological efforts. Moreover, new fields of implementation, related to molten carbonates, are also present: geology, glasses, production of nanocarbon particles etc. Considering other areas where this molten phase plays a major role, such as catalysis, waste destruction, surface treatment, it can be confirmed that the field of molten carbonates is very rich and offers many opportunities for fundamental science and competitive applications. Whatever their specific application, molten carbonates activity is associated to more efficient energy systems with low production of C02 and, in a prospective sense, to non-polluting energy using the value of C02. A recent event, the International Workshop on Molten Carbonates & Related Topics, IWMC201 I, held in Paris in 2011 , have put in evidence the importance to improve and exploit this investigation and technological domain."

Jan 1, 2012

By Rod Samuels, Rupert Allen, Thomas Harper

"Viceroy Resource Corporation of Vancouver, B.C., has recently developed and brought into production the Brewery Creek Mine, an open-pit heap leach gold mine, located 55km east of Dawson City in Yukon, Canada. Mineable reserves are 15.2 million tonnes of ore grading 1.45 grams/tonne, containing 22 tonnes (707,315 oz) of gold. Ore processing employs the heap leach technology using run-of-mine ore. Highlights of 1996 activity included construction of a 158,000 m2 of leach pad, placing 1.9 million tonnes of ore at a grade of 1. 46 gpt to the leach pad, construction and successful commissioning of the ADR plant, and pouring of the first gold bar on November 15th.Permitting of this mine has drawn significant attention because of the innovated heap leach technology; although this technology has been proven in other jurisdictions, it has not been used at such extreme northern sites where winter temperatures routinely reach -45°C for extended periods.ABSTRACT ONLY"

Jan 1, 1997

By Alexander I. Raitchenko

"An electroconductive viscous liquid may flow in laminar or turbulent regime under Lorentz-force generated by the intercrossed electric current and magnetic field. When there is a starting flat layer between hard and free boundaries with surface tension the spatial Lorentz-force can create a specific stationary regime of flow: the plane free surface will transform into the wavy one, and the movement in the depth will be not laminar and not turbulent, but this regime will be characterized by organized forms with indications of ""rolling of long cylindrical drops"". Wave-length is determined by the viscosity, the density, the surface tension, the average thickness of layer, and Lorentz-force. ·The limit of wavy regime is determined by most long of wave which is directly proportional to the critical value of specific flow and inversely proportional to the kinetic viscosity. The proper critical value of Reynolds number is determined by the dimensionless combination containing surface tension, density, viscosity, and Lorentz-force. The mentioned dimensio.nless combination in our case is some criterion substituting the known Kapitsa number for case of the thin viscous liquid layers under gravity. Spreading of admixture by mechanism of wavy regime is more rapid than by common diffusion or by laminar flow. The suggested conception can be a contribution into the theoretical basis for elaboration of some specific liquid metals technologies."

Jan 1, 1999

By Michael S. Moats, Daniel Kim, Shijie Wang

"The behavior and deportment of lead, arsenic, antimony and bismuth are critical in producing high quality cathode by copper electrorefining. A critical review of research related to these elements is presented along with a comparison to industrial data, where appropriate. These elements exist predominantly in the anode as complex oxides along die grain boundaries. Upon dissolution, Group 15 elements report both to the electrolyte and slimes while lead essentially enters the slimes. The deportment of the Group 15 elements appears to be influenced by several chemical interactions which are discussed. The effect of these elements on floating slimes and anode passivation is reviewed. Under normal electrorefining conditions, lead, antimony and bismuth are thought to enter the cathode through the encapsulation of slime particles. The literature indicates that arsenic enters the cathode predominately by electrolyte entrainment. Finally, areas for future research regarding these elements are presented.IntroductionControlling lead, arsenic, antimony and bismuth is critically important for the production of high quality cathode in copper electrorefining. The reasons for this are twofold. First, ASTM Grade 1 Cathode specifications [1] for these elements are low, as listed in Table 1. Second, they can affect the efficiency of the electrorefining process (e.g., through passivation, current efficiency, slime processing)."

Jan 1, 2012

By Pekka Hanniala

The falling real price level of copper metal and changes in the treatment and refining charges has been characteristic to the copper industry during the last few decades. Outokumpu's continuous development of the Flash Smelting Technology and increased productivity of the smelters based on these improvements may be one of the basic reasons that have influenced to these trends. From the early beginning of the Flash Smelting Technology, it has been characterized by low operation costs and low emissions, and the vision has been to develop the technology towards Direct Blister Flash Smelting. In Direct Blister Flash Smelting, both smelting and converting are carried out in one furnace making it possible to reduce the number of unit operation steps and thus lower both operation and investment costs. The merger of large copper production companies taken place during the last few years is a sign of a new age in copper production business. Now, the aim is to increase the productivity of copper production not just by utilizing the economy of scale but also by increasing integration and optimization of the whole production chain from mine to refinery. This also means increasing win- win based cooperation between companies. A Production Network concept based on the Flash Converting process enables existing smelters to decrease the operating costs and expand the smelting capacity with minimum investment and at the same time to decrease the emissions of the smelters. The new structure in ownership and partnership between copper production companies makes it easier to adopt the Production Network concept to both new and existing plants, where there exists a lot of built-in capacity. The paper presents Outokumpu's prediction on how the new options for the smelters will contribute to further changes in the structure of copper production. These visions are illustrated by giving examples on how the combination of matte production, Flash Converting, and Direct-to-Blister Flash Smelting could be adapted in existing and new smelters.

Jan 1, 2002

By Erwin Flender, Preben N. Hansen, Peter R. Sahm

"Until now FDM-Techniques have been widely used for Modeling Solidification Processes in Castings. Often a rigid, regular type of enmeshment (cubes, , --) have been used. This has the advantage of low CPU-costs, but the disadvantage of a zig-zag presentation of the interface between the casting and the mold. The last point is the reason why FEM-Techniques, giving the possibility of a true presentation of the shape in the enmeshment, are increasingly used. The disadvantage is the high CPU-costs. In this paper, a technique is presented, which uses the FDM-Mesh with the zig-zag presentation of shape and ADI-Algorithms to calculate temperatures and gradients. The new idea is that the calculated parameters are not presented related to the mesh in which they are calculated, but displayed using the true shape of the casting. Such an advantage of both low CPU-costs and shape correct presentation of the calculated results are achieved. IntroductionThe main reason for using a regular type of enmeshment is that it gives the possibility, via ADI-Algorithms, of obtaining a very fast FDM-Technique. The technique presented by P.R. Sahm and P. N. Hansen (1984), and also used by E. Flender (1985), is numerically so stable that average time steps, at least 200 times larger than the limit given by the explicit FDM-Technique, can be applied. To obtain reasonably good results, average time steps in the range of 20 to 50 times the explicit limit seems to be applicable. It should be pointed out,however, that FDM-Techniques can be used on arbitrary nets, the disadvantages being the same as for the FEM-Techniques. This has, among others, been discussed by P.R. Sahm and P.N. Hansen (1984)."

Jan 1, 1986

By Hai-Xing Fang, Chao Liu, Tao Zhang, Bing Xie, Hong-Yi Li, Cui Li

"Hongge Ore, a kind of vanadium-titanium magnetite ore containing high content of chromium, is valuable resource for extracting Fe, V and Cr in China. During present processing of the ore, vanadium and chromium were both concentrated in slag, leading to higher content of chromium in the vanadium slag than that of common one in Pan-Steel. Mineral phases and characteristics of spine! crystals, which influenced greatly subsequent roasting process, in the vanadium slag under different cooling conditions were investigated by using XRD and SEM/EDS. Results showed that vanadium slags containing various contents of chromium were composed of spine!, in which V and Cr were both concentrated, olivine and pyroxene. Growth rate of spine ls decreased sharply below 1350°C. The non-isothermal crystallization process could be described by modified Avrami equation and Ozawa equation. Avrami exponent and Ozawa index were calculated and growth mechanism of spine! crystals was discussed.IntroductionVanadium (V) as well as chromium (Cr) is important non-ferrous metal widely used in materials and chemical industries [1, 2]. Especially, both of them are important alloying elements for the production of high alloyed steels to achieve desired physical-chemical and mechanical properties. Vanadium-titanium magnetite ore in Panzhihua-Xichang area (China) is an important raw material for extracting vanadium. During the extracting process, vanadium is firstly reduced into hot metal and then concentrated in slag phase by blowing oxygen into the hot metal in converter [3]. This kind of slag containing 5~20 wt% V20 3 are usually roasted with sodium or calcium salts and then leached to obtain vanadium containing solution and final products. Current vanadium slag obtained from normal vanadium-titanium magnetite ore contains low content of Cr20 3 and chromium extraction is thus ignored. However, chromium content in the vanadium slag would be increased intensively when the Hongge Ore used, which is also important vanadium titanium magnetite in Panzhihua-Xichang area containing 0.2~0.8 wt% Cr203. Therefore, this kind of vanadium slag with high content of chromium would also be important sources for vanadium and chromium extraction. According to previous work [4], both vanadium and chromium could be extracted from vanadium slag with high content of chromium by salt roasting and leaching, which is illustrated in Fig.1."

Jan 1, 2013

By H. Kamiya, H. Hasegawa, M. Nojiri, S. Matsui, Y. Fukuda, M. Tsukada

"The present paper focuses on the action mechanism of anionic polymer dispersants in dense Si3N4 and SiC suspension. An atomic force microscope (AFM) was used to determine the relationship between the macroscopic suspension viscosity and the microscopic adsorbed structure of a polymer dispersant at the solid / liquid interface. The surface interactions within the suspensions were analyzed in various dispersant pH and additive conditions. The addition of an anionic polymer dispersant decreased Si3N4 and SiC suspension viscosity and increased electro-steric repulsion force on the non-oxide surface in solution at pH> 6 which was the isoelectric point of the materials. It was assumed that the increase of repulsive force was promoted by a hydrophobic adsorption of polymer dispersant on the non-oxide particles.IntroductionThe surface of silicon nitride and silicon carbide powders in a water suspension system has quite a complex molecular structure. In the case of Si3N4, hydroxyl and ammonium groups form on the surface and the pH of the suspension is increased from neutral to about 10 due to surface oxidation. The particle surface is negatively charged in alkaline solutions (pH=10), because the isoelectric point of silicon nitride exists in the pH range from 5 to 6. However, in spite of charging the negative surface charge, an anionic polymeric dispersant is generally used for the reduction in slurry viscosity.In dense SiC suspensions, an anionic polymer dispersant is generally used in order to disperse aggregates and reduce the suspension viscosity, too. Since an anionic dispersant is used in alkaline solutions higher than the isoelectric point of silicon carbide, the dispersant adsorbed on the negative charged surfaces of SiC.Few researchers have discussed and estimated the adsorption mechanism and structure of anionic polymeric dispersants on silicon nitride and silicon carbide surfaces. This is because it is difficult to observe the structure and measure the interaction at the solid/liquid interfuce directly. However, new developments in surface-force measurement technology have enabled the determination of non-DLVO type interaction for analyzing aggregation behavior2. The use of the AFM for analyzing the effects of various surfactants and co-polymers on colloidal dispersions and solid surfaces has also begun to rapidly expand to characterize the interaction between solid surfaces."

Jan 1, 2000

By M. -V. Wang

Hydrotreating and hydrorefining (HT and HDS) spent catalysts contain molybdenum, vanadium, nickel or cobalt at concentration levels that can make metals recovery economically viable. Quanzhou Jing-Tai of China has developed, through many years of operating experience in metal recovery from spent catalysts, a simple process for recovery of these metals and the production of environmentally benign residues. The process first subjects the catalysts to a low-temperature calcination step, followed by grinding of the calcine. The ground material is then leached with 10-20% v/v hydrogen peroxide to recover metals such as Mo, V and Ni or Co. This step has a selectivity that is greater than 95% for the metals. The undissovled residue, which contains mainly Ah03 and Si02, can be dewaterd and used in the production of masonry bricks. The pH of the rich liquor is then adjusted to between 0.5 and 2.5 by adding dilute sulfuric acid to co-precipitate Mo and V, with a recovery rate of greater than 99%. The lean liquor contains mostly dissolved Ni or Co, which can be recovered through precipitation at a pH of between 8.5 and 9.5 by caustic additions. The final liquor is then sent to an ion exchange step for final recovery and cleanup of residual metals. The effluent is then discharged after a simple wastewater treatment process, which has been found to meet all environmental requirements. The entire process has been found to be simple, cost-effective with minimal environmental impacts while achieving the goal of complete resource recovery from spent catalysts commercially.

Jan 1, 2000

By Jorge Alberto Soares Tenório, Victor Bridi Telles, Denise Crocce Romano Espinosa, Felipe Fardin Grillo, Vicente de Paulo Ferreira Marques Sobrinho, José Roberto de Oliveira

"This research aims to study the process of incorporation of the metal iron in electric arc furnace dust (EAFD), from a steel mill producing long steel by liquid iron in addition to the changing temperature of 1400 degree Celsius altering experimental conditions such as how to add the EAFD (as received and in the form of briquettes), the percentage of EAFD to be added (10, 20 and 30% of initial weight of sample pig iron) and the time of withdrawal of the sample of pig iron and slag (30 minutes after the addition of EAFD). Previously, the EAFD will be characterized using the following techniques: chemical analysis, particle size analysis, X-ray diffraction, scanning electron microscopy (SEM) and Energy Dispersive Spectroscopy (EDS) microanalysis. After characterization, the eletric arc furnace dust to be added to the bath of liquid iron, will be divided into 2 types: the first order of addition will be in the form ""as received"" from the plant and the second is through the agglomeration of EAFD in the form of briquettes. The achievement of fusion experiments in laboratory scale, will take place in a vertical tubular furnace with temperature control. The fusion experiments to assess the incorporation of the metal iron will use graphite crucibles. A flow of inert gas (argon) will be maintained inside the furnace during the experiments. It is expected that the results obtained at the end of the research allow the evaluation of the iron metal incorporation of eletric arc furnace dust in hot metal bath.IntroductionThe steel industry generates a variety of solid wastes, liquid effluents and gaseous emissions at various stages of processing. The electric furnace dust (EAFD), generated in electric arc furnaces, represents a major problem for their content of chemical elements such as zinc, iron, chromium, cadmium, among others, issued to the atmosphere during the manufacture of steel[1]."

Jan 1, 2012

By Selvin Yesilay, Munevver Caki, Canbora Bayraktar, Bekir Karasu, Rahmi Imrak

"In this study, the utilization capability of the solid wastes taken from a commercial roof tile and brick factory in Eskisehir of Turkiye has been investigated in the production of stoneware bodies which can be formed by slip casting. At the first stage, X-ray fluorescent (XRF) and X-ray difractometer (XRD) analyses of the wastes were performed. Depending upon the results, a body recipe with an optimum casting concentration was adjusted. The bodies obtained from prepared slips were fired at 1160 oC as glazed and unglazed forms. Then, they were undergone certain tests in order to determine their firing shrinkage values, water absorption levels and optical parameters. To establish what kind of phase formations occurred after firing as a result of waste incorporations into bodies XRD analysis was conducted. Additionally, effects of such a compositional modification on the microstructure of the bodies were examined by a scanning electron microscope (SEM). Consequently, it was concluded that fired roof tile and brick wastes could be evaluated in both glazed and unglazed stoneware bodies. Introduction Stoneware is the general name applied to many wares fired between 1150 and 1300 °C. It has a different and denser structure than those of ceramics produced at lower temperatures. Fired stoneware possesses a lower water absorption value. When matured at a high temperature, it gives a possibility for the use of feldspar as a main ingredient [1-2]. Colors of stoneware can be brown, red, white and most of the times beige. Firing usually takes place in oxidation atmosphere but also reduction can be rarely used. This naturally has an effect on the body colors [3]. Earth, which contains clay minerals, becomes plastic mud when mixed with water, has a capability to be easily shaped and can be hardened without cracking if fired at 900-1000 °C, is referred as one of the brick and tile raw materials [4]. Natural and aesthetic appearances of buildings obtained with brick and tile products, which make them preferable especially for construction sector, are of importance. Because clays being main raw material of that type of productions generally do not exist as pure materials in nature, their usability depends on their mineralogy and impurities they contain [5]."

Jan 1, 2008

By Ted H. Eyde

Natural Zeolites are a less expensive and in certain applications a superior alternative to organic ion exchange resins. Mining and metallurgical waste streams are difficult to treat because the effluents which contain potentially valuable heavy metals such as copper, lead, and silver are often highly acidic and contain significant quantities of suspended solids. Under rigorous operational conditions, certain natural zeolites can remove the metals, which if desired can be recovered by either elution or conventional smelting techniques. There are significant differences in cation exchange rate, selectivity and capacity as well as resistance to either high or low pH, blocking cations and tolerance to elevated or depressed temperature and pressure not only between different zeolite minerals but between the same mineral from different deposits. Applying natural zeolites to the treatment of mining and metallurgical waste streams depends on matching the specific zeolite to the effluent by characterization of the zeolite minerals.

Jan 1, 1993

By A. Filzwieser

The highest current density suitable for the electrowinning process is between 50 to 60 % of its limiting current density. One of the most important influences on the limiting current density is the thickness of the hydrodynamic boundary layer near the electrode surface. Therefore, the fluid flow in a copper electrowinning cell is calculated. The numerical simulation - using the CFD-software package FIRE® - considers all three different types of the fluid flow, namely, the natural convection, the forced convection by electrolyte circulation and the forced convection by electrochemically induced gas stirring. The simulation of natural convection is based on the different density values in the boundary layer at the electrode surface given by a density/concentration correlation. The copper concentration - linked with the current density by Faraday law - is solved by an additional transport equation. The simulation of the forced convection by the electrochemically-induced gas stirring is done by using a real two-phase calculation. That means that all differential equations are solved again for the second phase. The numerical solution of the fluid flow field is compared with the results of LDA- measurements, which were done in a special cell. The software for the LDA enabled a calculation of the void fraction possible and therefore a rough estimate of the mass transfer coefficient through the prevailing gas bubble induced convection can be made by assuming the influence of relative bubble volume.

Jan 1, 1999

By B. C. Jena

Activities of carbon, cobalt and nickel were evaluated in the ternary systems iron-carbon-cobalt and iron-carbon-nickel for the temperature range 1300-1600°C for cobalt and 1300-1700°C for nickel. The carbon activities were determined from the knowledge of activities (1) in the binary system iron-carbon, (2) in the dilute ternary systems and (3) from the knowledge of carbon saturation data. The activities were mathematically expressed with the Taylor series expansion of Wagner's interaction parameter formalism modified to suit concentrated solutions. The cobalt and nickel activities were determined from the knowledge of carbon activities by applying the Gibbs-Schuhmann integration and from cobalt and nickel activities in the binary systems iron-cobalt and iron-nickel. Partial molar enthalpies of mixing were determined based on the temperature behaviour of the activity coefficients.

Jan 1, 1992

By Lin Li, Xiang Li, Yifang Zheng, Jilai Xue, Jun Zhu

"Al drops and gas bubbles in the anode-cathode space of aluminum electrolysis cell are of great importance for cell operation improvement in metal loss, current efficiency and energy consumption. A direct observation on the Al drop, gas bubble and ultrasound was carried out through a see-through cell. The Al drop immersed into the cryolitic melt was found moving up and down irregularly in the anode-cathode space without electrolysis, which was then completely dissolved into the melt. During electrolysis, the Al drop came to the anode area and reacted with the gas bubbles generated on the anode. Under ultrasound, the gas bubbles were removed from the anode surface while the Al drop was kept on the side of anode. The observed phenomena were useful for technology improvement in reducing the anode-cathode distance or lowering the energy consumption in aluminum electrolysis.IntroductionDuring aluminum electrolysis, aluminum metal drop and anodic gas bubble are in close contact each other within the anode-cathode space, and the interaction between them can produce significant impact on metal loss, current efficiency and energy consumption. The motions of the Al drop and the gas bubble are also related to the dissolution of aluminum metal into cryolitic melt and the cell voltage drop due to the bubble layer covering the anode surface.A number of studies have been carried out using different types of see-through cells, where the dissolving process of metal Al into cryolitic melts (metal fog) in the anode-cathode space was directly observed and photographed [1, 2]. With the similar method, some direct observations on the anodic bubble behaviors with and without ultrasound were performed during aluminum electrolysis [3-6]. However, to our best knowledge, there is no published work on direct observation on the behavior of Al drops and anodic gas bubbles staying together within the same anode-cathode space, as well as the motion and interaction of them in cryolite-alumina melts."

Jan 1, 2011

Copper and gangue mineralogy constitute the most critical parameters for the hydrometallurgical processing and cost-efficient extraction of copper. Minor changes in copper-, rock-, or alteration mineralogy can severely impact the comminution efficiency, curing, agglomeration, acid consumption, copper extraction and PLS impurity loading. Further, copper leach operations, particularly in the southwestern United States, are increasingly challenged by a combination of low grades and semi-refractory copper. This paper discusses the metallurgical and economical benefits of continuous mineralogical analyses in order to establish and operate a mineralogical data base in copper leach operations. Troubleshooting for copper extraction, integration of process mineralogy into production forecasting, and process optimization will be illustrated with operational experiences from Chile and the United States.

Jan 1, 1999

By John Petersen

Heap bioleaching technology has become well established for the exploitation of copper sulfide ores. Still, in many operations the rate of copper extraction is rather slow, often taking two years or more to recover 80% of the copper. Chalcocite, the most common secondary copper sulfide, leaches by a two-stage mechanism. The first stage is rapid, whereas the second stage has a high activation energy and proceeds slowly at ambient temperatures. Nonetheless, this rate is still considerably faster than what is typically realized in a full-scale heap. A comprehensive column bioleaching study of a chalcocite ore has shown that the chalcocite columns are leached in a zone-wise fashion. The first zone corresponds to the first stage of chalcocite leaching, where all ferric produced by the bacteria is immediately consumed and all acid entering with the feed solution is consumed within a relatively narrow band. The second stage of chalcocite leaching proceeds much more slowly in the wake of the first stage, within a zone that grows gradually over the entire length of the column. The overall rate of leaching is thus determined by the rate of acid supply into the column rather than by mineral or bacterial kinetics, at least until the entire column is engaged in second-stage chalcocite leaching. In full scale heaps, there is evidence to suggest that solution distribution favours channelling between relatively large clusters of material which are exposed only to stagnant solution. Reagents have to migrate into such clusters by diffusion, which retards the delivery of acid dramatically. Thus, we believe that the rate of chalcocite oxidation in heaps is governed by sideways diffusion rather than downward migration. Column experimental results have been reproduced with a comprehensive heap-modelling tool. The model predicts that by simply changing the length of the average diffusion channel from column conditions (a few cm) to heap conditions (tens of cm), extraction times can change from weeks to years under otherwise identical conditions.

Jan 1, 2003

By O. Kitamura, H. Kubota

The Harima Works started its ISP operation in 1966 and been expanding its production capacity from 3,000 tonne Zn/month and 1,500 tonne Pb/month to 7,500 tonne Zn/month and 2,500 tonne Pb/month. It is not only treating zinc, lead and bulk concentrates but also secondary materials like Waelz kiln oxide from the Shisaka Works of Sumitomo Metal Mining, waste treatment sludges, industrial wastes and others. Its final products cover Prime Western Grade (PWG) zinc, Special High Grade (SHG) zinc, continuous galvanizing grade zinc, electrolytic lead, cadmium, indium, thallium and sulfuric acid. This paper briefly describes the smelter's historical and present operations. The key data for the current impurity control management and for the distribution of impurities such as copper, iron and arsenic are presented.

Jan 1, 2000