Search Documents

By Dan Adams

A number of gas-liquid processes require high intensity agitation systems to provide uniform blending and dispersion of reactants in order to achieve desired end products. Processes such as hydrogenation, fermentation, and minerals processing have used conventional down pumping or radial agitation systems with some success. In 1996, LIGHTNIN introduced the concept of Up-Pumping to the industrial marketplace as an improved mixing technology for these applications. For processes requiring gas-liquid mass transfer, such as those listed above, conventional mixing technology requires the use of gas introduction devices (sparges) below impellers. These devices can be a maintenance concern due to plugging and erosion in the presence of solids. Up-Pumping impeller systems are able to draw in a significant amount of gas from the headspace, much more so than conventional vortexing impellers designed for headspace gas incorporation. This paper will demonstrate the effectiveness of Up-Pumping impeller systems that have the potential to eliminate need for sparge devices entirely. It demonstrates the ability of Up-Pumpers to re-entrain gas for higher utilization compared with conventional impeller technology. This is significant in applications using costly gases such as enriched oxygen or hydrogen, reducing overall operating costs of production.

Jan 1, 2003

By Matthias Frommer, Carl-Peter Reipl, Reinhard Flende

"Today there is a growing demand for strip of superior steels with specifically tailored technological properties. Especially strips of high-strength, micro-alloyed steel grades applied to manufacture longitudinally and spiral-welded pipes are a growth market. Tubes are generally required to have high strength and sufficient toughness values and thus favour specific hot strip microstructures. The correlation of chemical analysis, process parameters and mechanical properties with microstructural features is still a challenging task. During the last decades, scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD) have become useful tools for the characterization of complex microstructures. The EBSD data provides an immense variety of post-processing possibilities, e.g. related to grains, grain boundaries, misorientations or texture. This paper highlights the results of an advanced analysis of microstructures representing industrial produced hot-rolled strips and presents an approach to define and quantify some essential microstructural parameters.IntroductionHigh-strength microalloyed steels have been used for the production of welded pipes for more than 30 years. However, the alloy design of pipeline grades is being continuously modified and the process technology optimized because of the increasing high strength-toughness combination requirement for pipeline steels. Compact strip production (CSP®) technology is an upcoming promising route for the production of high-quality pipeline steel grades [1]."

Jan 1, 2012

By Doug Halbe

?Many are called, but few are chosen.? The biblical adage applies not only to life, but also to hydrometallurgical processes. There have been, in the past, many outstanding successes with new processes ? and also some dismal failures. What are the odds of success for a new process? When there have been problems, why? What can you do to make sure these problems don?t occur with your process? What effect will a slow startup have on project economics? How do financial institutions ? the people who loan your company money for the project ? feel about new processes and why? Is it possible to predict or estimate the time required to reach design parameters?and if so, how do you sell this estimate to management ? and financial institutions? Probably most important ? when do you start thinking about the answers to these questions?

Jan 1, 2003

By R. A. Cockerell

This paper is concerned with the application of Advanced Process Control (APC) to copper smelting processes. A number of key issues relating to the application of APC, such as modelling for control, process dynamics and time delays, instrumentation and sampling, are discussed. A general methodology for the application of APC is then presented. Finally, three case studies are presented to demonstrate the benefits and efficacy of applying APC.

Jan 1, 1999

By K. A. Elbarawy

Processing of Egyptian barite ore with a composition of 85.5% BaSO4; 2.75%SiO2;1.56%Fe2O3 and 5.1% Al2O3 was performed with the aim to prepare pure barium salts. The process took place through pelletization-solid state reduction and leaching steps. Each of these steps was optimized. Pure barium sulphate (99% < 0.82µm) and carbonate (99%<0.75µm )were the final products. This article deals with the reduction process that occur whn coal was added to the ore during pelletization in the ratio of 5:1 stoichiometry. Optimum reduction of pellets of 8-12mm in diameter was achieved after 60 minutes at 1050oC and under a rate of 5 lmin-1 of nitrogen atmosphere, where 87.79% of the ore was reduced. The kinetic studies showed that the reduction process could be modeled according to the core mechanism of diffusion control in which the effective diffusivity is based on the surface area of unreacted ore. The activation energy calculated was 92.7 kJmol-1.

Jan 1, 2006

By I. Barin, G. Eriksson, F. Sauert

Computer-aided calculations using data bases and program systems are more and more needed for the rational development and optirnization of high-temperature processes. The calculation of mass and energy fluxes between different process steps as well as the determination of the chemical equilibria will be discussed, giving examples from nonferrous metallurgy. The simulation of a waste-material treatment process including high-temperature combustion and gas-cleaning systems will also be demonstrated.

Jan 1, 1988

By Robert F. Jenkins, King G. Robertson

This paper presents a practical approach for utilizing a computer model to determine the mass balance for a typical UBC recycling complex - starting with raw materials input, through scrap preparation, delacquering, melting, alloy adjustment and casting. This model is especially concerned with metal unit losses throughout the recycling complex with emphasis on metal losses at the melting furnace. The model also addresses the application of hardener alloys, metallurgical salts, chlorine for demagging, and reagents for acid gas emissions control. Other issues addressed are dross generation, acid gas emissions and dirt and fines to landfill. One benefit of the model is the conversion of annual production objectives to hourly production rates and resource requirements taking into account production schedules, maintenance downtime, and operations inefficiencies.

Jan 1, 2000

The Port Kembla Copper (PKC) copper smelting facilities were commissioned during 2000. Numerous difficulties were encountered during the commissioning such as multiple reactor tuyere line failures, absorbing acid tower refractory collapse, and Noranda Reactor and Mitsubishi Converter process control problems. These problems are described along with the actions taken to overcome them. Process development is described particularly for the Mitsubishi Converter and Acid Plant.

Jan 1, 2002

By J. C. Agarwal

Rare earth metal alloys are becoming increasingly important, particularly those of neodymium, because of their magnetic properties. This paper will present a generalized approach to the production economics of the metallic rare earth alloys. With appropriate regard for the chemistry of different rare earths and the large impact of economies of scale, it is possible to make fairly accurate estimates of the production costs of other rare earth alloys as well.

Jan 1, 1989

By B. Yalamanchili

Gerdau Ameristeel Beaumont presents its systematic approach for upgrade decisions that has developed over 30 years of ongoing capital projects for quality and cost improvements. This system serves to identify product needs, select process improvement strategies, justify them, and assist multi-department communications and decision-making. This is illustrated with Beaumont mills? last Stelmor upgrade and leads to a discussion of the need to consider Life Cycles of both products and technologies as we move to answer the challenges of the future.

Jan 1, 2006

By Mark E. Schlesinger

A substantial database exists for the thermodynamic properties of many antimonide compounds, but these have rarely been compiled or critically discussed. An abbreviated version of a full?scale review of the thermodynamic properties of binary antimonide compounds is presented, focusing on the choice of experimental techniques.

Jan 1, 2006

By Pradip

The selective adsorption of chemisorbing fatty acids at high temperatures together with the addition of soda ash and lignin sulfonate as depressants is the key to the industrial processing of bastnaesite ores. This paper presents the results of a fundamental investigation that indicate that alkyl hydroxamates can be an alternative collector for the beneficiation of bastnaesite ores that contain barite and calcite as the principal gangue minerals. The primary mechanism for providing sites for the chemisorption of hydroxamate on bastnaesite appears to be through dissolution of cations, formation of the respective hydroxo complexes and readsorption at the interface.

Jan 1, 1989

By M. S. Moats

A considerable amount of research has been conducted to determine the causes of anode passivation. Chemical and electrochemical reactions that occur after passivation have received little attention. Chronopotentiometry, linear sweep voltammetry, cyclic voltammetry, and impedance spectroscopy have been used to elucidate three reactions that occur after passivation of commercial copper anodes. These involve the dissolution of silver and subsequent cementation and transformation of selenides, the oxidation of lead sulfate to lead oxide, and oxygen evolution. The amount of silver dissolution depends on the silver content of the anode, the time to passivation, and the molar ratio of Ag/(Se+Te). The oxidation of lead from PbSO4 to PbOx explains a potential plateau of oxygen evolution. Silver affects the duration of oxygen evolution on the PbOx. Anodes containing kupferglimmer display a characteristic oxygen evolution potential. It is believed that kupferglimmer provides a lower overpotential for oxygen evolution than the other slime phases or passivated surface.

Jan 1, 1999

By D. P. Briand

Falconbridge Limited operates a smelter in Sudbury, consisting of fluid bed roasters, acid plant, electric furnaces and Peirce-Smith converters, to treat local concentrate and other custom materials. The products are a low iron, nickel- copper-cobalt matte and sulphuric acid. This paper describes the operation and highlights some of the recent efforts to improve human resource effectiveness, to reduce sulphur dioxide emissions and ground level concentration excursions, to develop and expand the custom feed business, to improve productivity and performance in safety and hygiene, and to improve furnace integrity and process control.

Jan 1, 1993

By Wolfgang Baum

Remediation work on thermal process dusts and slags has been primarily based on chemical analyses. These data offer little information for the assessment of treatability and reuse potential. In addition, the lack of mineralogical residue characterization has frequently caused time-consuming and inefficient waste management. This paper will outline the cost-effective, and sucessful use of process-oriented mineralogical analyses for treatment and beneficial reuse of various thermal residues. These include a patented process for detoxification of Pb-contaminated bottom ash, the pyrometallurgical treatment of K 061, the reprocessing of lead smelter slag as well as various power plant residues.

Jan 1, 1992

By Stella Agatzini

Column leach tests were conducted to evaluate the amenability of poor Greece nickel laterites to heap leaching with dilute sulfuric acid at ambient temperature. The ore tested was a limonitic laterite with less than 1 % nickel and it was subjected to a suitable pretreatment with water prior to it being loaded into the columns, following findings of preliminary research work. The acid solution was recycled after suitable pH adjustment. Factorial designs were used to determine the effects and interactions of the following factors: sulfuric acid concentration, ore column height, ore grain size and ratio of leach solution volume to the ore quantity. The response which were investigated included nickel and cobalt recoveries, codissolution of iron, calcium, magnesium, aluminum, chromium and silica and also sulfuric acid consumption. Experimental error was also detennined. The tests showed that a nickel recovery of 88% could be achieved in 60 days.

Jan 1, 1993

By M. Sadayappan

The grain refinement characteristics of four low-lead and lead-free copper base alloys for plumbing applications were investigated. These are leaded yellow brass (C85800). SeBiLOY III (C89550), silicon brasses (C87500 & C87800) and silicon bronzes (C87600 & C87610); Boron and zirconium were found to be the most effective .grain refiners for copper .alloys produced using the permanent mold cast processes. The study indicates that the type of grain refiner to be used is dependent on the alloy type, alloying constituents and their content. After grain refinement, hot tearing resistance of the alloys was improved but mechanical properties remained unaffected. Alloys refined with boron are prone to the formation of hard spots, which will have adverse effect on the surface quality of the castings during polishing and buffing.

Jan 1, 1999

By Dhanesh Chandra

Long term stability studies were conducted on four variants of LaNi5; 10,000 hydriding/dehydriding cycles were used to evaluate their suitability for a metal hydride cooling system. Thermodynamic and structural studies were conducted to determine changes in these materials during cycling test period. The hydrogen sorption properties of LaNi5.2, and Lao 9Gd0.1Ni5 and LaNi4.75In0.27 were seriously degraded during the tests but the LaNi4.8Sn0.22 hydride was virtually unaffected. Hydride isotherms were measured at the beginning and at intervals through out the test period to observe the nature and extent of damage degradation in the sorption properties. X-ray diffraction studies of the alloys (LaNi5.2, LaO.9Gd0.1Ni5 LaNi4 8Sn0.22) and their respective hydride, before and after test, provided insight with regards to the observed changes in the hydride properties. Electron microscopic studies were also conducted to evaluate the changes in particle sizes.

Jan 1, 1989

By Jürgen Antrekowitsch

Typical zinc oxides recovered from wastes like steel mill dusts and neutral leaching residues are of a low quality because of impurities like fluorine, chlorine, lead and others. Therefore, they are not comparable to technical grade zinc oxides produced in “French” or “American Process”. Some new developments, most of them still in pilot scale, try to establish processes where higher qualities of the product should be achieved. Zinc oxides are not only supposed to be an input material for electrolytic zinc production. Far more, they should find their way into the zinc oxide market as a substitute for technical grade zinc oxides. Furthermore, a new field of application for these oxides has been investigated at the department of Nonferrous Metallurgy, University of Leoben. Because of a higher acceptance concerning different impurities in relation to zinc winning electrolyses, a use in electrolytic galvanizing shows an interesting option. Therefore, synthetic zinc oxides with different impurities were generated to study the effect of these impurities especially on the quality of the zinc layer. Typical steel sheets, as used for car bodies, were electrolytically galvanized and the resulting layer was analysed, as main impurities compounds of fluorine, chlorine, iron, lead and calcium were used for the investigations. Beside the layer quality, the current efficiency and the possible galvanizing speed were examined. The results give an indication, weather such an alternative application can be feasible from a technical and economical point of view or not. 597

Jan 1, 2008

By Shize Jin

Effect of four polyols, namely ethylene glycol (EGL), glycerol (GCL), propanediol (PDL), butanediol (BDL) and three organic acids, namely oxalic acid (OA), malonic acid (MA) and succinic acid (SA) on the current efficiency (CE) and the cell voltage during zinc electrowinning was studied. Galvanostatic polarization was conducted in a supporting electrolyte (SE) containing 180 g dm-³ H2SO4, 60 g dm-³ Zn2+ and 8 g dm-³ Mn2+ at 38°C with magnetic stirring. The imposed current density was 50 mA cm-². The anodes were made of a Pb-Ag alloy and the cathodes were made of an aluminum alloy. The results showed that all the polyols tested in this study decreased the current efficiency and the cell voltage, but the decrease of the cell voltage was not important. Oxalic and succinic acids decreased the current efficiency to a less extent than the polyols, but did not decrease the cell voltage much. The only compound that increased the current efficiency was malonic acid, and its capacity of decreasing the cell voltage was the highest within the seven tested organic compounds.

Jan 1, 2003