Search Documents

By Wei Gao, Qing-cai Liu, Cun-fang Lu, Jian Yang, Hinmi Zheng

"The mode of occurrence of sulfur and mercury in 57 Chinese bituminous coals have been examined using X-ray fluorescence spectrometry (XRF), X-ray diffraction (XRD), and Zeeman atomic absorption mercury spectrometer. Mercury levels in coal are related to the geographic location of the coals and types of the coals. A synthesis of result indicated that most likely occurrence modes of mercury in high-sulfur and high-mercury coals are in solid solution in pyrite. Our study from 57 coal samples showed that most values of mercury concentration in coal varied from 100 to 1000 ng/g with an average of approximately 500ng/g, and mathematical model about correlation between mercury and sulfur was gained by mathematical statistics. This is apparent that mercury and sulfur vary concomitantly from coal data (table 3) , the high correlation between them in all coals at confidence of 95% ( a=0.05 ) .1. INTRODUCTIONThere contained about one trillion ton abundant coal resources in China. As a leading level of proven coal reserves in the world, the coals mainly distributed in north China and northwest China, especially in Shanxi, Guizhou, Shanxi provinces and Inner-Mongolia autonomous region. At the same time, China has the largest production and consumption of coal, and has the output of coal nearly accounted for 37 percent of the world's production. Coal-fired power plants are the major source of energy generation in China, and the proportion of coal combustion is up to 75 percent in the total energy configuration. Therefore, the mercury pollution caused by coal-fired has become a topic of wide-spread discussions since 1990. The contamination of mercury of human activities accounted for 10 to 30 percent [1], and the mercury emissions of coal-fired flue gas has made the greatest contribution to the pollution of atmosphere[2] In the past 30 years, the global increasing concentration of mercury pollutant in atmosphere maybe result from coal combustion[2]. The mercury emissions caused by coal-burning has become the main reason of China's mercury pollution, and the characteristics of mercury pollution is closely related to China's energy configuration, additionally, the features of mercury pollution have changed from the point pollution in 1970's to diffused pollution today[3]. Mercury can be found in various types of coals, and it is evaporated into gas phase during the combustion process."

Jan 1, 2011

By Malsuzaki. Kenji

A mathematical simulation model of the Imperial Smelting Furnace operation has been developed for purpose of improving the furnace operation. The model consists of top, shaft and bottom regions. Analysis in the shaft region is based on differential heat and materials balances taking account of reaction kinetics and heat transfer rates, and those in the top and the bottom regions are based on heat and materials balances under a steady-state condition. Longitudinal distributions of process variables such as temperatures of gas, sinter and coke, gas composition and fractional conversion under a practical operating condition were calculated. With this model, the furnace performance under various operating conditions also can be shown reasonably predicted.

Jan 1, 2003

By H. Walqui

Southern Peru Copper Corporation (SPCC) are currently modernizing the Ilo copper smelter. A single ISASMELT furnace will start smelting 1,200,000 tonnes per year of concentrate during the second half of 2006. The existing Peirce Smith converters are being upgraded for converting the matte to blister copper and a new acid plant and oxygen plant are being installed. Two new anode furnaces and a twin anode casting wheel have been installed in 2005 and commissioned in January 2006. The modernization project will ensure the smelter satisfies new environmental regulations due to come into force in January 2007. This paper summarises the background to the modernization project, describes the main design features of the new copper smelter and summarises progress on the smelter construction as of early 2006. This paper describes the genesis of the Ilo Smelter Modernization Project and describes in details the scope and current status of the project.

Jan 1, 2006

By Jinwu Kang

The hydraulic turbine blade of the matensitic stainless steel (Cr13%,Ni5%,Mo1%) is a kind of large and curved shape, which is susceptible to deformation in both casting and heat treatment processes. The coupling analysis of heat transfer, phase transformation and stress in heat treatment process of the turbine blade for Three Gorges Project is carried out by using Deform-3D software. Its temperature fields, phase fields and stress fields in heat treatment process are obtained. And its deformation is predicted. In the cooling process of normalizing, the blade exhibits relatively large deformation. Based on the stress analysis and deformation prediction in heat treatment process, an algorithm for the determination of reverse deformation of the blade casting in heat treatment process is presented. And the reverse deformation distribution of blade is obtained.

Jan 1, 2010

By B. Mishra

Calcium and lithium gallides have been synthesized by powder metallurgy techniques in the stoichiometries that can be used as reduction alloys for the Rocky Flats Plant Salt-Scrub (SS) process. The SS process is performed to recover valuable metals from salts generated in the electrorefining and the molten salt extraction processes. Combustion synthesis has been optimized for variable heating rates up to the reaction ignition temperature and for green densities of the powder compacts in terms of the ignition temperature and the exothermic heating of the product in an effort to develop LiGa and CaGaz alloys. The problems arising from the melting point and density differences of calcium, lithium and gallium have also been studied. The SS alloy compositions were produced by mixing, pressing and sintering the metal-powders. The efficiency of the intermetallic alloy, Ca-17 wt. pct. Ga, as a reductant and the effect of gallium on salt clean- up has been discussed. Measurement of actinide recovery has been studied with cerium as the surrogate for the actinide metal. The development of an alloy for SS reduces a major contaminated waste disposal problem besides recovering the valuable reactive metal.

Jan 1, 1993

By L. Lü, M. O. Lai

"Mechanical alloying is a dry, high energy ball milling process which has been used to synthesize metallic powders in the solid state. The present study use this technique to synthesize Cu-base shape memory alloy powder from commercial Cu70Zn30, Cu86Zn14 and element AI powders. The evolution and formation of shape memory alloy powder were monitored using X-ray diffraction and microscopy. It was observed that shape memory alloy powder started to form after 1.8 ks of mechanical alloying. ? phase was clearly detected after 3.6 ks of mechanical alloying. The intensity of X-ray diffraction of the y phase increased when mechanical alloying duration was prolonged indicating an increase in the amount of y phase. Microstructure observation showed different stages of formation of alloyed powders: welding between powders and formation of layered structure, deformation and fracturing of layered structure, and finally the formation of alloyed powders.IntroductionMechanical alloying (MA) is a process used for producing powders with controlled and extremely fine microstructure. It was original developed in 1966 (1) to produce aNi-based superalloy combining oxide dispersion strengthening with gamma prime precipitation hardening. In recent years this technique has been used in producing a wide range of materials including intermetallic compounds (2, 3), amorphous materials (4-6) and other materials (7-9). In MA, a blend of powders is subjected to highly energetic compressive collision. The powder panicles are welded and fractured during ball milling. Therefore, it is essential that at least one of powders should be ductile to act as combiner. It has however been found that brittle components without soft element can also be mechanically alloyed (10), even ceramic powders (11).The present work aims to study the mechanism of formation of shape memory alloy powder during MA."

Jan 1, 1994

By A. K. Kyllo, G. G. Richards

"The formation and control of accretions is an important aspect of process operation for gas injection. The nature of the accretion formed can have a considerable effect on a process, especially on the life of the lance or the refractories in the tuyere region. There are three basic shapes of accretion formed on tuyeres; pipes, hemispheres and hollow-cored hemispheres. However, there are wide variations within these shapes. Generally, the type of accretion formed will depend on the injector design, certain operating parameters and the physical properties of the bath materials. This paper seeks to collect the results of previous and current physical and mathematical modelling together with data gathered from operating furnaces, to obtain a better understanding of the effects of process design and operating variables on accretion formation.IntroductionAn important consideration in the design of a gas injection process is the possible freezing of the bath either around the tuyere or on the lance. With proper design, freezing may be controlled to provide protection of the lance or refractory, and to avoid blockage. Improper design may lead to tuyere blockage and significant refractory or lance erosion. In view of this, a good understanding of the heat transfer in the injection region is essential.While tuyere blockage has been a persistent problem since the inception of submerged gas injection processes, the problem of accretion formation was not studied in detail until the development of the shrouded tuyere by Savard and Lee. A number of studies relating to accretion formation have been carried out since then, but there is still little information available relating the nature of the accretion formed to the design of the injection system.The build up of materials on lances is a similar problem, and may also be either beneficial or detrimental, depending on circumstances. Unfortunately, there is even less information available regarding build up on lances than there is relating to tuyere accretions. While the form of build up on lances is generally a simple coating of the lance, accretions on tuyeres tend to be more complex. Tuyere accretions tend to occur in one of three basic forms: pipe, hemispherical and hollow-cored hemispherical (Figure 1). However, there appears to be a considerable variation within these forms."

Jan 1, 1996

By George Kazonich

The high costs and environmental problems associated with making iron and steel in the United States is driving the development of new technologies to replace the blast furnace. A prototype reactor incorporating rocket technology was designed and built. This rapid rate reactor was operated successfully and consistently made iron metal. Minus 325-mesh magnetite particles could be reduced to iron metal in less than 50 ms in a high temperature flow through reactor. Iron product was recovered inside the reactor and in a downstream cyclonic separator. The results of typical operation and how parametric changes affected the reduction of iron ore concentrates are discussed.

Jan 1, 1993

By J. L. Sanchez

Using a special double-zone transpiration reactor, the vapor transport chemistry of vanadium pentoxide in the presence of water vapor has been investigated. Three possible volatile hydroxides above V,O,(s) are reported in the literature: VO,(OH),, V,O,(OH),, and VO(OH),. In the present study, it was established that VO(OH), is the principal gaseous hydroxide species formed. The predominant reaction was found to be: { } The vapor pressure of VO(OH), was measured as a function of temperature, water pressure, oxygen pressure and flowrate. The results have been used to determine the Gibbs free energy of the above reaction as a function of temperature: { } The results of the present work were combined with thermodynamic data reported in the literature to obtain expressions for the AGO for the reaction above V,0,(1) and the AGO of formation (units in cal/g-mole).

Jan 1, 1993

By T. W. Gonzales

The refractory performance of Peirce-Smith converters is considered to be mainly determined by effects of process control and refractory installation design. BHP Copper has shown that, over the last four years, considerable improvements in tuyere line life can be affected .by maintaining a uniform temperature in the operating converter and by ensuring sufficient and specific placement of expansion allowance in the construction of the refractory brickwork. A combination of optimized crane availability, rapid matte transfer, converter operating practices, new refractory installation techniques and applications has minimized out-of stack time. In addition, larger diameter tuyere pipes and hard piping have increased blowing rates and lowered cycle times, which has resulted in a tuyere line performance in excess of 62,500 tonnes of blister copper before maintenance is required. This paper discusses the refractory installation design changes that were made to increase tuyere line life.

Jan 1, 1999

By Zhi-yong Liu

A novel process, which includes hydrochloric acid leaching, iron powder cementation, sulphide precipitation and spray pyrolysis, was proposed to treat iron concentrate recovered from zinc kiln slag for comprehensive utilization. Treated by two-stage hydrochloric acid leaching, the leaching extents of Ag, Pb, Cu, Fe and Zn are 96.78%, 95.14%, 97.72%, 94.51% and 87.74%, respectively. More than 99% Cu and Ag are recovered from the leach liquor when iron powder is 25% higher than the stoichiometric requirement. More than 96% Pb and Zn is removed with three times of theoretical consumption of FeS, and the concentration of impurities of the final solution is less than 500 mg/L. Fe2O3 powder, which is spherical with a mean size of 12 μm and purity of 99%, is prepared with final solution at 700 °C. In this process, not only the metal values can be recovered effectively, but also the iron resources of zinc kiln slag can be converted into high purity Fe2O3, thus, the comprehensive utilization of iron concentrate recovered from zinc kiln slag can be realized.

By Shengping Li, Wei Lv, Gangqiang Fan, Xuewei Lv, Yingyi Zhang

The electrical conductivity of high titania slag, as being an important fundamental physical property utilized in the theoretical understanding of mass transfer phenomena and requirement of practical electric smelting processes, were measured by AC Impedance Spectroscopy using four-electrode method for ternary TiO2–FeO–Ti2O3 slag system based on 85 type of titania slag in Panzhihua in this work. The experiment results show that the slags have a high magnitude of the order of 80–180 s/cm−1 in the whole experimental temperature range from 1523 to 2013 K. The Ti2O3 exhibits very strong effect on increasing the electrical conductivity of high-titania slag since the specific values averagely increase by 55 s/cm−1 with corresponding Ti2O3 content range from 10 to 16 wt%. the X-ray diffraction gram and phases calculated by FactSage are presented and interpreted to discuss the impact of phase change on the electrical conductivity.

Mar 1, 2017

By Joseph Sofra

It has become increasingly evident that sustainable metals production in the 21" century requires producers to balance the needs of cost effective, high value production with that of responsible plant operation. This is becoming more difficult as lower grade and more complex feed materials, including recycled scrap and residues, arc being processed to reduce production costs and decrease exposure to primary metal market fluctuations. One particular facet of the metals industry facing these challenges in the 21 st century arc copper producers. The recent steady decline in the copper price has seen the industry cut expenditure, tighten control on income streams and focus on high returns on capital investment. For these reasons copper producers arc looking towards flexible technologies that can deliver high value products, with minimal environmental impact at low capital and low sustainable operating costs. Ausmelt's Top Submerged Lancing (TSL) technology for copper production is a low cost, proven technology for the processing of both primary and secondary copper materials. Both the smelting and converting operations introduce significant advantages in environmental performance, improved process efficiencies and high rates of metal recovery. Ausmelt has made significant gains in the past 4 years in establishing a strong market position for its copper technology. New installations in China, South Africa and India as well as existing operations in Zimbabwe and China have demonstrated its effectiveness. This paper reviews the application of Ausmelt Technology for both smelting and converting of primary and secondary sources. It discusses Ausmelt's design and implementation philosophy, and how this philosophy meshes with the needs of the end user.

Jan 1, 2003

By Jilai Xue

Fe-Ni alloys can be used as raw material in making stainless steel. Laterite nickel ore is one of mineral resources for producing nickel alloys. In this work, the laterite ore after dehydration at 800 °C and the anthracite as reducing agent were mixed for pre-reduction at 900 °C, and then reduced to form Fe-Ni alloys at 1550-1620 °C through carbon-thermal reduction process. A high Ni-content alloy component in the metallurgical mixture can be formed through pre-reduction. Better separation of the resulting metals from the slag is found with lower Ni-content alloys produced or higher temperatures during reduction. An effective processing of Fe-Ni alloys needs further understanding of the process fundamentals and optimizing of the process parameters.

Jan 1, 2010

By J. Fogarty, J. Sofra

The mobile telecommunications sector is one of the fastest growing industries worldwide. However, increasingly stringent environmental regulations are placing pressure on manufacturers to accept responsibility for end of life products. The companies are therefore exploring avenues to recover the valuable components contained within the mobile telecommunications devices thus reducing the quantities of toxic components going to landfill. Batteries used to power the devices, are typically based on either nickel-cadmium, nickel metal hydride, or lithium ion cells. They contain toxic metals including nickel, cadmium, lithium, potassium, lead, and cobalt in a complicated arrangement of battery cells surrounded by a metals then plastic casing. The Ausmelt Catalytic Waste Converter (CWC) for waste treatment and recycling is well suited to processing all three mobile phone battery types for the recovery of valuable metals in marketable products that can be recycled to industry without turning out harmful levels of toxic emissions. Ausmelt recently demonstrated the capabilities of its CWC by continuously processing 4.5 tonnes of nickel-cadmium batteries. Using Ausmelt's pilot plant facility in Australia, the nickel-cadmium batteries were processed to produce a nickel iron sulphide (matte), a cadmium fume and a final slag which satisfied CS toxicity leach test criteria and was safe f<~r disposal to landfill. This paper explores the commercial development of the Ausmelt CWC for treating each of the three battery types in light of (a) the outcomes of the recent demonstration, and (b) the current and expected future availability of batteries for processing.

Jan 1, 2000

By Joseph Sofra

It has become increasingly evident that sustainable metals production in the 21st century requires producers to balance the needs of cost effective, high value production with that of responsible plant operation. This is becoming more difficult as lower grade and more complex feed materials, including recycled scrap and residues, are being processed to reduce production costs and decrease exposure to primary metal market fluctuations. One particular facet of the metals industry facing these challenges in the 21st century are copper producers, The recent steady decline in the copper price has seen the industry cut expenditure, tighten control on income streams and focus on high returns on capital investment. For these reasons copper producers are looking towards flexible technologies that can deliver high value products, with minimal environmental impact at low capital and low sustainable operating costs. Ausmelt&apos;s Top Submerged Lancing (TSL) technology for copper production is a low cost, proven technology for the processing of both primary and secondary copper materials. Both the smelting and converting operations introduce significant advantages in environmental performance, improved process efficiencies and high rates of metal recovery, Ausmelt has made significant gains in the past 4 years in establishing a strong market position for its copper technology, New installations in China, South Africa and India as well as existing operations in Zimbabwe and China have demonstrated its effectiveness. This paper reviews the application of Ausmelt Technology for both smelting and converting of primary and secondary sources, It discusses Ausmelt&apos;s design and implementation philosophy, and how this philosophy meshes with the needs of the end user.

Jan 1, 2003

By Fiona J. Stevens McFadden, Gregory J. Hardie, Mark P. Taylor, William Uru

"Over 20 million tonnes of installed aluminium smelting capacity exists worldwide, with smelter energy con.sumption in the range 14-17 kWh/kg aluminium. In terms of the reduction cell technology itself, the lowest sustained energy consumption is just below 13DC kWh/kg, or 50% energy efficient.For 15 years Comalco Aluminium Ltd. in Australia has been engaged in developing and testing reduction cells that use a refractory hard cathode, composed of a TiBif carbon composite coating over a carbon cathode. This technology has the potential to reduce energy consumption significantly while simultaneously increasing the life of the cells, which is currently limited by wear rate of the conventional carbon cathodes used throughout the worldIntroductionThe successful development of an aluminium wettable cathode technology affords the opportunity to the cell designer and smelter operator to fundamentally change the physical operating characteristics of the Hall-Heroult process. With this revolutionary capability in hand, published papers and patents have indicated that the technology may be exploited in a wide variety of ways to improve the economic performance of aluminium smelting process. Comalco has been developing refractory hard cathode technology for more than 15 years and has been exploring a number of ways that the technology may be commercially applied in a smelter operation [l]."

Jan 1, 2000

By Taegong Ryu

A thermal plasma process was used to synthesize nanosized tungsten carbide -cobalt composite powder, in which ammonium paratungstate and cobalt oxide were reacted with a gas mixture containing CH4, H2 and Ar. The reduction and carburization of vaporized precursors produced nanosized tungsten carbide (WC1-x) - cobalt composite powder, which sometimes contained small amounts of W2C and/or W phase. The effects of gas composition, plasma torch power, and the flow rate of plasma gas on the product composition and grain size were investigated. The grain size of synthesized tungsten carbide powder was less than 20 nm. The synthesized composite powders were also subjected to a hydrogen heat treatment to fully carburize WC1-x, W2C, and W phases to the WC phase as well as to remove excess carbon in the product. Finally nanosized WC-Co composite powder of grain size less than 50 nm was obtained.

Jan 1, 2009

By Pietro Navarra

Cooling of critical furnace equipment to produce freeze lining is of particular interest as many metallurgical processes are intensified while attempting to prolong campaign life. This idea was combined with high-capacity heat pipes in the design of a copper slag launder. The design methodology of the launder and heat pipe cooling system is examined in this paper. With reliable material properties and operating conditions, CFD was used to quantitatively predict the skull thickness and the corresponding heat load applied to the slag launder. The operational limitations of heat pipe technology were considered and an appropriate cooling system was incorporated into the model. Parametric modeling was used to simulate several launder and heat pipe configurations. The generated results were then used to optimize the design of the launder, which was built and tested in August of 2005. The experimental performance of the cooling system is evaluated and compared with the model results.

Jan 1, 2006

By Suman Das, Justin J. Gambone, Rohan Bansal, Ranadip Acharya, Paul Cilino

"This paper focuses on generating a quantitative microstructure prediction model for Scanning Laser Epitaxy (SLE) process based on coupled flow-thermal modeling using Finite Volume method. SLE is a laser-based additive manufacturing process for the deposition of equiaxed, directionally solidified and single-crystal nickel superalloys through the melting of alloy powders onto superalloy substrates. In the current work, the detailed effects of natural and Marangoni convection on the flow field are studied and the results are analyzed in terms of the temperature gradient, vorticity parameter, melt pool dimensions and mushy region extent. The detailed property data of the processed superalloy and the laser scan path are incorporated in the model to predict the microstructure in realistic scenario. An optimization study is carried out to evaluate the critical parameter values at which the columnar-to-equiaxed and the oriented-tomisoriented transition take place. This work is sponsored by the Office of Naval Research through grant N00014-11-1-0670.IntroductionSLE is a laser-based additive manufacturing process for the creation of structures in equiaxed, directionally solidified and single-crystal nickel superalloys through the selective melting and resolidification of superalloy powders. In SLE, a tightly focused laser beam is guided by a highspeed galvanometer scanners allowing for tight control of the amount of energy being applied to the top of the powder bed, as well as the speed at which the melt pool moves across the substrate. Under the proper operating conditions and with sufficient substrate meltback, the solidification microstructure follows the morphology of the underlying substrate, allowing for directional and even SX growth.Several reports on the modeling aspects of laser cladding-based additive manufacturing approaches can be found in the literature. Approaches based on Finite Element Methods (FEM) and Finite Volume Methods (FVM) are employed for the thermal modeling of the system [1, 2]. Gaumann coupled the Columnar to Equiaxed Transition (CET) modeling with the Rosenthal solution in earlier work based on laser cladding [3]. Rappaz et. al. provided a detailed modeling of the microstructure/columnar orientation based on the solidification velocity and crystalline orientation [4]. This approach is based on the selection of the growth direction that closely follows the melt pool normal direction. Later on, substrate orientation is also taken into account [5, 6]."

Jan 1, 2013