Search Documents

By M. K. Mohan

Lead recovery from process solutions contributes not only to the conservation of resources but also clean environment. Zeolites are natural aluminosilicates, which finds applications as catalysts and in wastewater treatment. In the present investigation, studies were taken up on the processing of Pb from process solutions by zeolites. Effects of pH of the solution, time and type of zeolite viz. chabazite, mordenite, erionite and clinoptilolite on the removal of Pb from solutions was investigated. Rate of sorption was found to depend on the pH of the solution and about 99 pct. recovery was observed at pH 6. Optimal conditions were established for the maximum recovery of lead from process solutions. Possible sorption mechanisms were proposed. The calculated adsorption constants calculated from Langmuir and Freundlich equations showed that the adsorption of lead on chabazite was strong.

Jan 1, 1999

By Min-Min Lin, Bing Xie, Hong-Yi Li, Yang Yang

After precipitation of ammonium vanadates from vanadium-containing leaching liquor, vanadium (V(V)) and chromium (Cr(VI)) exist in the waste water in form of vanadate ions and chromate ions. In order to efficiently extract and recover V(V) and Cr(VI) from waste water, an environment-friendly method based on anion exchange was investigated in batch tests using macroporous weak base resin Dex-V. The adsorption conditions optimizes in detail, including the effect of pH, initial metal concentration, resin volume, contact time and temperature. The ion-exchange adsorption process for both V(V) and Cr(VI) showed maximum capacity at pH 3.0 for an initial concentration of 100 mg L−1, and reached equilibrium after about 40 min of contact at 298 K. The maximum adsorption ratio under the optimum conditions for V(V) and Cr(VI) was 98.98 and 99.87%, respectively. Result shows that the established method is a promising alternative for simultaneous extraction of vanadium and chromium.

Mar 1, 2018

By Bin Xu, Qian Li, Xishan Li, Yongbin Yang, Hongwei Li, Tao Jiang, Yan Zhang

The cyanide leaching rate of gold from a multi-refractory gold concentrate (18.05 g/t Au) containing 1.62% As, 20.76% S, 6.95% C and 1.31% Sb was only 1.33%. The enhancement of gold leaching was studied mainly by the pretreatment of oxidative roasting and alkaline sulfide washing. Results showed that after the two-stage roasting (i.e., I stage of 500 °C, 1 h and II stage of 700 °C, 2 h) most of sulfur (93.84%) and carbon (98.27%) were removed, but the gold leaching rate of calcine just reached 71.33% because the residual arsenic (0.63%) and antimony (1.15%) were still high. After alkaline sulfide (i.e., NaOH and Na2S) washing, the residual arsenic and antimony was further decreased to 0.21 and 0.65%, respectively. The gold leaching rate of the treated calcine by cyanidation could increase to 93.52% substantially. Also, the optimized particle size, NaCN concentration and leaching time were −0.045 mm over 85%, 0.1% and 36 h, respectively.

Mar 1, 2017

By Shadia J. Ikhmayies

"Cadmium sulfide (CdS) in the form of thin films is an interesting material because it has a large variety of applications ranging from photovoltaic to luminescent devices. N-type CdS is usually used as a window layer in the heterojunction CdS/CdTe thin film solar cells. A review of the photoluminescence (PL) spectra ofn-type CdS thin films prepared by different techniques was performed. The effects of different dopants and impurities and the effects of temperature and deposition parameters on the PL spectra were discussed. Annealing in different atmospheres causes the changes in material structure and phase change from cubic to hexagonal phase which can be detected through the variations in the PL spectra. CdCh heat treatment improves the cystallinity of the films and enhances the exciton peaks and the green band in the PL spectra.IntroductionThin CdS films deserve attention because their expected gap emission lies very close to the highest sensitivity of the human eye. Thus, one might assume that thin CdS films are an appealing host for photonic devices [ l]. They have been used in a lot of applications including electronic and optoelectronic devices [2]. Thin films ofn-type CdS are widely used as a window layer in heterojunction solar cells such as CdS/CdTe solar cells. Doped and undoped CdS thin films can be obtained by different techniques such as; spray pyrolysis (SP) [3], chemical bath deposition (CBD) [2, 4], pulsed laser deposition [5, 6, 7], laser ablation [l], thermal evaporation [8].Several experimental techniques have been used in order to study semiconductor defects. In particular, photoluminescence (PL) has been shown as a powerful and sensitive tool in examining the crystal quality of polycrystalline thin films. PL can be used in the detection of defects which are radiative active. These defects can also act as traps in the transport of carriers [9]. The photoluminescence (PL) of thin film CdS is strongly influenced by the unbalanced stoichiometry, which is typical for CdS and is in general evoked by a Cd surplus. With increasing Cd content, the emission spectra move far below the gap to the red spectral range. Besides stoichiometry problems, independent of the material deposited, the PL properties of thin films depend on surface features and the influence of the interface between the film material and the substrate [10]."

Jan 1, 2013

By Gökhan Hardal, Berat Yüksel Price

Nickel manganite based negative temperature coefficient (NTC) thermistors have good temperature sensor characteristics and electrical stability for temperature measurement applications. In this study, the electrical and microstructural properties of Ni0.5Co0.5Cu0.3Zn0.3Mn1.4O4 NTC thermistor were investigated. The samples were fabricated by the conventional solid-state reaction method. The powders were calcinated at 900 °C for 2 h and the samples were sintered at 1200 and 1300 °C for 5 h in air. The bulk density of samples was 5.07 and 4.96 g/cm3, respectively. The microstructure of samples was observed using a scanning electron microscope. The electrical resistance was measured in a temperature programmable furnace between 25 and 85 °C. The electrical resistivity of the Ni0.5Co0.5Cu0.3Zn0.3Mn1.4O4 sample increased from 52 Ω cm to 95 Ω cm when the sintering temperature increased from 1200 to 1300 °C. The material constant “B”, sensitivity coefficient “α” and activation energy “Ea” values were also calculated for the NTC thermistors.

Mar 1, 2017

By Antonio de Lucas, Juan Francisco Rodríguez, Ignacio Gracia, Mª Teresa García

"The amount of waste of Polystyrene (PS) foams is increasing in last years due to their use in insulation, protecting and, storing many different food products. Conventional methods of recycling such as crushing and shrinking by heated air or frictional heat have the disadvantages of molecular degradation, resulting in a reduction of the quality of the recycled polymer. Dissolution and shrinking with suitable solvents is one of the cheapest and more efficient ways of polystyrene recycling but in the process of the solvent recovery by distillation a certain degree of molecular degradation is produced. In this way, CO2 supercritical technology appears as an interesting alternative for the elimination of solvent. This work proposes a global process to polystyrene recycling in two steps: a polystyrene dissolution with a suitable “green” solvent followed by its elimination by supercritical tecnologhy. In order to develop a “green process” the constituents of essential oils, limonene, terpinene, cymene, and phellandrene, are selected as the most appropriated solvents. Introduction In the last years, disposal of the non-biodegradable plastic wastes has been recognized as a serious environmental problem. Recycling these wastes has great interest in order to prevent the environmental pollution and to preserve natural sources (1, 2, 3). Since the Polystyrene foams (PS) is one of the most used foam in isolation, protecting and food storage most of recycling work is concerned with this polyolefin (4). The two main alternatives for treating polymer wastes are energy recycling, where wastes are incinerated, and mechanical recycling (5). Environmental argumentations such as toxic emissions are building up a public resistance against incineration process (6). Mechanical recycling is a popular recovery path for manufacturers and is carried out on single-polymer waste streams. Any way, the market for recycled products can only be found if the quality is close to that of the original. Unfortunately the process of classification and further recovery of these wastes makes them often more expensive than virgin plastic (7, 8). Solvent extraction is one of the cheapest and more efficient ways for PS recycling. If it is done in house of waste producers the separation between plastics could be easy and effective and the transport costs would be eliminated."

Jan 1, 2008

By Fabiola Alvarez, Ana E. Bote, Daniel Pasquevich

"The oxidation of aluminum and its alloys was extensively studied for improving the corrosion resistance in structural materials having high specific strengths. But this reaction involves the formation of a very thin barrier layer on the metallic pieces. Furthermore, the ·recent development of the directed melt oxidation process for producing metal-ceramic; composites has renewed the interest in the study of interaction between gases and metals. Oxidation experiments in the presence of different chlorine partial pressures and at different temperatures were performed in ·a thermogravimetric balance, and microstructures were analyzed by electronic microscopy and X-ray diffraction. The oxy-chlorination kinetics was determined and the oxide formed W(IS amorphous at temperatures below 600 °C and crystalline .at higher temperatures. The appropriate experimental conditions for the fastest completed oxidation was further determined.IntroductionThe use of fine powders for the manufacture of ceramic components has significant advantages. They include excellent sinterability; low sintering temperature and better microstructure leading to improved mechanical properties. The conventional method of producing fine oxide powders involves controlled precipitation and pirolysis of suitable salts. The main limitation of the high temperature decomposition route is the evolution of environmentally unacceptable and corrosive gases. Controlled precipitation of hydroxides from solutions of salts, followed by thermal treatment involves large volumes of solutions and the calcination step that can induce grain growth (1).Direct oxidation of aluminum metal for producing alumina powder requires high temperatures for the direct oxidation of molten Al alloys by a vapor phase oxidant process (2, 3) or high technological process like thermal plasma reactor ( 4).Oxidation of high purity aluminum (5, 6) below the melting temperature· is initially characterized by a nearly linear reaction rate, followed by a rate which decreases rapidly with further weight gain. However, the oxidation rate of an aluminummagnesium alloy is much faster and it does not conform to any common oxidation law, but it is nearly parabolic at temperatures between 200 and 400 °C, an nearly linear· above 400 °C."

Jan 1, 2000

By J. N. Kondo, M. Hara, T. Smida, N. Ooto, K. Domen

"A porous material composed of two-dimensional anionic sheets of a layered perovskite, KSrNb30 10, was studied as photocatalyst for the production of Hz in the presence of alcohol sacrificial donors. Colloidal single and multi-layered HSr2Nb30 10 sheets were formed by intercalating ietra(n-buthylammonium) cations into the interlayeres of H+-exchanged KSr2Nb30 10 (HSr2Nb30 10), and addition of HN03 solution to the colloidal suspension precipitated the porous materials in which HSrNb30 10 sh~ets rand~mly stuck together. Original HSr2Nb30 10 before exfoliation had a BET surface area of 1 m2 g-1, whereas the surface area of a porous material prepared under optimal conditions exceeded 100 m2 g-1. The porous HSr2Nb30 10 had considerably higher photocatalytic'activitie8 for oxidation of 1-propanol and 1-buthanol than HSr2Nb39io, indicating that in the porous materials many niobate sheets are available for decomposition of these large alcohols.IntroductionQuite a research effort has gone into the design and study of porous materials. Such materials with large surface areas would have applications in highly efficient adsorbents or catalytic reactions.We have been studying photocatalytic reaction by cation-exchangeable layered metal oxides, where alkali metal cations are intercalated into the interlayers of inorganic sheets.[1,2] There are several advantages to using layered compounds rather than bulk powders for photocatalysis. Layered compound is rich in variety, in addition, modifications of them are easily performed by exchanging alkali metal cations in the inter layers for H + or other metal cations. The most important advantage is that some layered compounds have considerably high photocatalytic activities than bulk catalysts because the electrons and holes generated in each thin inorganic sheet readily reach interlayer spaces as reaction sites at the illterlayer spaces. It should be very important for further improvements· of layered photocatalysts to utilize two-dimensional inorganic sheets effectively."

Jan 1, 2000

By Vinod K. Sikka, René Cooper

"Cohoes, New York 12047 Intermetallics are an attractive class of advanced materials. The aluminide intermetallics offer advantages including: (1) lower density, (2) oxidation resistance, (3) carburization resistance, and (4) interesting mechanical properties because of their ordered crystal structure. Even though the attractive properties of the aluminides and other intermetallics have been known for nearly four decades, their practical applications have not been developed for two reasons: (1) the poor ductility (in some cases, both ambient and high temperatures) and (2) the lack of processability into meaningful components. Recent advances such as ductilization of Ni3Al by small additions of boron and the knowledge that environmental effects are the major cause of poor ductility in Fe3Al and FeAl systems have brought the intelmetallics into the forefront of research and their commercial applications. This paper has described a method for melting Ni3AI-based alloys that successfully utilize the exotherrn for the formation of NiAl from the elemental materials. The reaction-synthesis method has also been utilized for the production of NiAI and NiAI-based alloy powders from the elemental powders. The reaction-synthesized powders of NiAI and NiAI-based alloys were consolidated by hot extrusion and evaluated for tensile properties over a temperature range from room temperature to 1050ºC. The powder-processing conditions have been found to have more influence on the ductile-to-brittle transition temperature of NiAI than the powder-production method.IntroductionIntermetallics are an attractive class of advanced materials [1-11]. The alum in ide interrnetallics offer advantages including: (1) lower density, (2) oxidation resistance, (3) carburization resistance, and (4) interesting mechanical properties because of their ordered crystal structure. Even though the attractive properties of the aluminides and other interrnetallics have been known for nearly four decades, their practical applications have not been developed for two reasons: (I) the poor ductility (in some cases, both ambient and high temperatures) and (2) the lack of processability into meaningful components. Recent advances such as ductilization of Ni3Al by small additions of boron and the knowledge that environmental effects are the major cause of poor ductility in Fe3Al and FeAl systems have brought the intermetallics into the forefront of research and their commercial applications. The paper will briefly review the processing techniques being pursued for the commercial applications of Ni3Al-based intermetallics. The major emphasis of the paper will deal with synthesis of Ni3Al and NiAI intelmetallics."

Jan 1, 1994

By C. Coetzee

Additives are commonly used in copper electrowinning to improve cathode morphology. Polysaccharides such as guar are generally favoured as additives due to their compatibility with solvent extraction. Polyacrylamides are, however, being considered as possible alternatives. Understanding the influence of the structural chemistry of additives on electrowinning performance is critical to utilise them efficiently. This paper investigated polyacrylamide additives which are structurally different; their effects on copper electrodeposition were characterized and compared to that of guar. Electrochemical impedance spectroscopy (EIS) were used to characterize the effects of molecular weight and ionic charge of the polyacrylamides on electrodeposition. The findings were compared against results obtained with an industrially used guar product. Equivalent circuit modelling of EIS data indicated that an increase in polyacrylamide concentration and a decrease in additive molecular weight increased the overall system resistance.

By R. Hurman Eric

Within the Ag-Pb-S ternary system, the boundaries of the immiscibility region together with the tie-line distributions were re-established at 925°C by the equilibrium-quenching technique where samples were kept in evacuated and sealed silica capsules. Activities of Pb were measured by the dew-point method along the Ag-Pb binary at 925°C, 1100° and l200°C, positive deviations were observed and the results were modeled by the Krupkowski formalism. Activities of Ag, Pb, and S, along the ternary miscibility gap were calculated at 925°C by utilizing the boundaries binary thermodynamics, phase equilibria and tie-lines. Activities of PbS within the pseudobinary Ag2S-PbS mattes were also measured by the dew-point technique and the results were again modeled by the Krupkowski formation where negative deviations were observed.

Jan 1, 2003

By R. Hurman Eric

Within the Ag-Pb-S ternary system, the boundaries of the immiscibility region together with the tie-line distributions were re-established at 925°C by the equilibrium-quenching technique where samples were kept in evacuated and sealed silica capsules. Activities of Pb were measured by the dew-point method along the Ag-Pb binary at 925°C, 1100° and 1200°C. positive deviations were observed and the results were modeled by the Krupkowski formalism. Activities of Ag, Pb, and S, along the ternary miscibility gap were calculated at 925°C by utilizing the boundaries binary thermodynamics, phase equilibria and tie-lines. Activities of PbS within the pseudobinary Ag2S-PbS mattes were also measured by the dew-point technique and the results were again modeled by the Krupkowski formation Where negative deviations were observed.

Jan 1, 2003

By Vahid Rastegar

"Characterization of the microstructure and revealing dendrites in the microstructure and also measuring the dendrites arm spacing and the distribution of silicon were studied in various pieces of compacted graphite cast irons with 0.17, 0.185, 0.2, 0.22 and 0.24 percent of mischmetal. Black-white and color metallography (quantitative and qualitative) were carried out on the various steps of the cast samples. Distribution of silicon was studied quantitatively using spot analysis with scanning electron microscopy. Furthermore, effects of two variables (cooling rate and mischmetal percentage) on dendrites arm spacing were investigated.In order to color metallography, the samples were plunged into a boiling solution of 18% KOH, 9% NaOH and 9% picric acid in distilled water. It was inferred that the microstructure coloration varies according to the sequence: green-->red-->yellow-->blue-->dark brown->light brown as the silicon content decreases. After observing dendrites, dendrites arm spacing was measured. In this method, it seems to be possible to predict the mechanical properties of compacted graphite cast irons by knowing dendrites arm spacing and without any destructive testing. After studying the two variables, it was concluded that dendrites arm spacing decreases as the amount of mischmetal increases and it increases as the cooling rate increases.IntroductionIn general, detecting of primary austenite dendrites is not possible in cast irons due to their solidification system. Observing the dendrites in the room temperature is possible only in those gray cast irons that contain type D graphite. With collecting data of dendrites arm spacing (DAS) measurements, it could be possible to achieve the mechanical properties of cast irons without any destructive testing. In this research by applying a particular method, primary austenite dendrites and also distribution of silicon in the microstructure has been observed."

Jan 1, 2012

By Tracy Lucas, Ian Hamill

"Issues of importance in the area of continuous casting centre around product quality. This can be affected by particle inclusions transported into the mould from upstream processes and by draw-down of particles from the meniscus. Turbulence of the meniscus can increase the latter and is also detrimental to product surface quality.Suitably validated Computational Fluid Dynamics (CFD) modelling can provide the operator with an efficient tool with which to investigate the effects of changes to the design and operation of the caster and associated plant.In this paper, examples are presented of the use of the CFD software, CFX, to simulate:•,free-surface shape and turbulence in the mould using deforming meshes•,solidification in the mould using a fixed-grid, source-based method•,argon gas injection through a submerged entry nozzle using a full multiphase model•,inclusion motion and removal in tundishes using an algebraic slip model.The CFD simulations of the free surface shape are complemented by detailed Particle Image Velocimetry measurements performed on a full-size water model of a thin-slab mould and upper strand. Close agreement is demonstrated between the predictions and experiments."

Jan 1, 1999

By Kenneth N. Han

Thermodynamic and kinetic aspects of nickel and cobalt leaching from metals. minerals and ores in various media have been reviewed and discussed in this paper. A kinetic model developed to delineate the leaching mechanisms for these metals has been discussed in view of experimental observations. The current review also includes the dissolution behavior of nickel and cobalt from various minerals such as oxides, sulrides. ocean floor manganese nodules, and laterites. A particular emphasis has been extended to similarities and differences of the dissolution behavior of these two metals in various media. The leaching of nickel as well as cobalt metal in acidic solutions and arnmoniacal solutions exhibits in most part mass transfer controlling. although at some pH's, chemical controlling or mixed controlling mechanisms seem to prevail. The leaching of nickel and cobalt from oxides in acids and ammoniacal solutions. on the other hand, can be described best by chemical controlling mechanisms.

Jan 1, 1993

By Yunqing Tian, Wenbin Huang, Weidong Zhang, Xiaopeng Wang, Gele Qing, Xiangjuan Duan

Pellet production requires iron ore concentrates have fine particle size, high specific surface area and good balling performance, so iron ore concentrates appropriate for pelletizing is limited compared to sintering. In order to extend the iron ore resources for pelletizing, the iron ore fines for sinter are studied in this paper.The effect of grinded iron ores o npelletizing, roasting and pellet quality were studied in this paper. The bond grinding index of iron ore fine is between 12.5 and 16.98 kwh/t. The grinded iron ore fine has good balling performance, the drop number and compressive strength of green pellet were improved with increase of grinded iron ore fine ratio. The compressive strength of roasted pellets were decreased with increase of grinded iron ore fine ratio, however it can be reached 2500 N.P −1 while proportioned with more than 80% of magnetite iron ore concentrate.

Mar 1, 2018

By Yosry Attia

Recent emphasis on environmental effects and costs of conventional mining processing, plus success in accelerating bacterial action, suggest that biotechnology be explored for gold ore processing. In our paper, the past experience with organisms in processing gold is reviewed. The use of microorganisms for liberation of gold from sulfide ores as a substitute for fine grinding is discussed. The possibility of accumulation of gold from solutions, such as cyanide solutions, is explored as a potential replacement for such processes, such as carbon-in-pulp or ion exchange. The improvement in engineering technology and kinetics needed to scale-up from laboratory experiments to production scale are outlined.

Jan 1, 1985

By Denise Crocce Romano Espinosa, Jorge Alberto Soares Tenorio, Amzy Tania Vallenas-Arevalo, Carlos Gonzalo Alvarez Rosario

Cyanideisatoxicchemicalusedinminingindustrytorecovergoldand silver in leaching process. Effluents containing cyanide can be treated by biore- mediation instead of physical and chemical processes which are often more expensive and less efficient. This study evaluated the capacity for free cyanide degradation of a Bacillus licheniformis strain previously isolated from an aban- donedgoldmine.First,bacterialgrowthinLBmediumthroughOD wasstudied. 600 Then,bacteriawasadaptedtogrowonalkalinemediumusingCAPSbuffertokeep pH10. Finally, cyanide degradation assays were performed using a 500 mgL −1 KCN pH10 50 mM CAPS solution. Free cyanide was measured using a polaro- graphicmethod.Temperatureinfluencewasevaluatedat27,32and37 °C.Results showedthat B. licheniformis was able todegrade 99% offree cyanide after 5 days of incubation and works better at 32 °C showing the strain potential for cyanide biotreatment in mining industry. (cid:1) (cid:1) (cid:1)

Mar 1, 2018

By Paul Van Negan

During the last decade, MHO has continued to diversify the feed. of its Hoboken smelter. The range of feed materials including larger proportions of precious metals has been extended and the production of minor metals has been developed. These diversifications have required further improvements at the smelter. Attention has been particularly focussed on an increase of productivity, compliance with emission standards and achievement of the highest recoveries of valuable elements. The assaying and sampling facilities have been considerably expanded and the different processing steps of the smelter are now also systematically controlled and managed by simulation models. The charge preparation at the sinter plant, returns handling, sinter conditioning and corresponding ventilation systems have been completely renewed. The annual smelting requirement is now achieved with two blast furnaces instead of three. This is the result of rebuilding and enlarging one of the furnaces and, of a completely new concept of the charge proportioning and charging systems, together with oxygen enrichment and blast air preheat. Ventilation capacity has also been drastically increased. A 7 MVA electric furnace for cleaning the slag from both blast furnaces. contributes to improving the overall metal recovery.

Jan 1, 1990

By Pietro Navarra

Cooling of critical furnace equipment to produce freeze lining is of particular interest as many metallurgical processes are intensified while attempting to prolong campaign life. This idea was combined with high-capacity heat pipes in the design of a copper slag launder. The design methodology of the launder and heat pipe cooling system is examined in this paper. With reliable material properties and operating conditions, CFD was used to quantitatively predict the skull thickness and the corresponding heat load applied to the slag launder. The operational limitations of heat pipe technology were considered and an appropriate cooling system was incorporated into the model. Parametric modeling was used to simulate several launder and heat pipe configurations. The generated results were then used to optimize the design of the launder, which was built and tested in August of 2005. The experimental performance of the cooling system is evaluated and compared with the model results.

Jan 1, 2006