Search Documents

By Michael L. Free

Bacterial oxidation of an arsenopyritic gold-ore .concentrate was carried out with continuous-flow .operation in 14-liter, mechanically agitated reactors. Samples from the slurry reactors were separated into solid and liquid fractions and analyzed separately to determine the electrochemical rates of sulfide conversion by the bacteria and the rates of direct bacterial oxidation of sulfide. The rates of the individual mechanisms are compared to the overall rates of biooxidation in the continuous-flow slurry reactors. The results show that the commonly hypothesize4 direct and indirect mechanisms of biooxidation both play a significant role in the bacterial oxidation of sulfide ores.

Jan 1, 1991

By Chengyi Ding, Xuewei Lv, Changyang Ji, Rende Zhang, Xiangwei Zheng

The fraction of liquid phase in sintered ore can be the most important factor to determine the sinter quality and yield in sintering process. The generation ability of liquid phase for mixture of iron ore powders is determined by basicity, roasting time, roasting temperature and chemical composition of iron ores. Five different iron ores were selected in this study and the dried powders of iron ore and CaO reagent (<200 mesh) were homogeneously mixed together at their required proportions, then 15g of the mixture was pressed under a pressure of 20MPa to make a cylindrical sample with a diameter of 20mm. The sintering temperature in this study was kept at 1280℃, the gas phase is air, the holding time was varied with its three levels of 5min,10min and 15min. After that, the sample was cooled under room temperature in the air, and the cooled sample was analyzed by using zeiss optical microscope. The mineral phase compositions were quantitatively determined with an open source image processing software, Image J whicn can calculate the fraction of liquid phase. Besides, the study on how to estimate the sintering behavior of the raw materials in different conditions by the theoretical calculation is of vital importance, and the development of this will greatly improve the sintering production. Factsage will be used to calculate the liquid phases formulation during the sintering. Comparing the experimental results and the theoretical calculation shows that the mass of liquid phase increases with increasing basicity during the sintering, besides, the mass of calcium ferrite increases with increasing basicity. The generation ability of liquid phase of iron ores can be predicted through the experiment verification.

Jan 1, 2015

By R. W. Bartlett

The extensive central Idaho black sand placer deposits are a potential source of rare earth elements, particularly the heavy rare earth elements that are not prevalent in commercial bastnasite deposits. These placers derive from the Idaho batholith. The geology, occurrence, and extent of these deposits are reviewed and the diverse mineral assemblages and complex mineral chemical compositions of these sands are described. Niobium, yttrium and thorium are also present in significant concentrations. The results of prior mining practice, including concentration and separation of the heavy minerals are reviewed. Technical approaches to extraction of rare earths from Idaho black sand concentrates are discussed.

Jan 1, 1992

By Ali Hasham

Reduction rates of FeO in CaO-SiO2-Al2O3 slags by Fe-C melts have been investigated experimentally at 1723 K. The rates were estimated using experimentally determined CO(g) evolution rates. Flash X-ray images were employed to visualize the behavior of the melt-slag interface during the reactions. The influence of melt interface was examined by conducting two types of experiments - (i) dropping one (or several) Fe-C droplet(s) weighing 2 g into the molten slag bath, and (ii) dropping a small amount (10-30 g) of slag onto a Fe-C melt weighing 400 g. The rates from both types of experiments were compared and analyzed to determine the rate limiting steps. It was established that neither the carbon transport in the Fe-C melt, nor the transport of gas species in the gas film adjacent to Fe-C melt was responsible in limiting the reaction rate. It is possible that the slag phase mass transport may be controlling the initial reduction rate in the droplet experiments. However, a, different mechanism was responsible in limiting the reduction reaction when the overall %C in the droplets fell to about 2-3.

Jan 1, 1992

By V. E. Antonov

Hydrides of iron and iron-based alloys are thermodynamically stable only at hydrogen pressures in the gigapascal range and rapidly loose hydrogen under ambient conditions. At low temperatures, however, these hydrides can be retained in a metastable state at atmospheric pressure after being cooled under the high pressure to liquid nitrogen temperature. This review will discuss the current state of studies on phase transformations in the Fe-H and related systems and also on the composition, crystal structure and physical properties of the hydrides, both under high hydrogen pressures and in the "quenched" metastable state at ambient pressure. The studies at ambient pressure include magnetization measurements, X-ray and neutron diffraction, Mossbauer spectroscopy and inelastic neutron scattering. In the sections on Mossbauer and structural investigations of hydrides of Fe-Cr and Ni-Fe alloys new experimental results will be presented.

Jan 1, 2002

By Zhijing Zhang

The management of hazardous wastes is important in a society which is increasingly concerned with environmental issues. Incinerators such as the slagging rotary kiln are widely used in the treatment of hazardous wastes. However, in order to assure a smooth operation of the rotary kiln, the melt should have both a low melting point and high fluidity. In this study, the fluidity of various hazardous waste rotary kiln slags was measured in terms of length of flow using the crucible test technique. It was found that the slags have melting points ranging from 1372 to 1424°C while their fluidities varied from 61-102 mm. The effect of addition of oxides on the fluidity of a slag containing 47 wt% SiO2 was also investigated. For this slag, additions of SiO2 (up to 56 wt%), FeO and Na20 increased fluidity, whereas the addition of CaO and A1203 resulted in lower fluidity values.

Jan 1, 2002

By Pertti Pekkala

Outokumpu has 25 years of experience in the SX area. The development of the solvent extraction plants responds to an ever increasing demand for lower operational costs wd for adaptability to process disturbances with minimized risks. In this paper the features of the VSF ("Vertical Smooth Flow") SX technology are described, such as the separated pumping and mixing, the homogenous gentle mixing, the droplet coalescence and the ultra pure settling. A major advantage of the mixing technology is the high stage efficiency of above 99 per cent. The connection between this and some features of the settler front section is clarified. The present design of VSF plants is based on experience of existing operations at, for example, Zaldivar, Radomiro, Morenci, Kokkola and Harjavalta. These production plants cover a unit capacity range of 60 to 3,600 m3/h expressed as a total flow. It is evident that there are no restrictive factors to increase the total flow up to 5,000-6,000 m3/h by introducing the VSF technology. The copper SX technology has a long history reflecting many individual features of the separate copper SX plants. Still it is necessary to verify all actual running parameters by pilot tests taking into account impurities, chemicals used etc. The design of SX plants is not only about the delivery of equipment but also a process concept, and it is best tailor-made and adapted to specific local requirements.

Jan 1, 1999

By S. Djaroudib

Keywords: iron recovery, hematite, hydrolysis, polyvinylpyridine The precipitation of hematite (Fe2O3) from ferric chloride media at ambient pressure and at temperatures below 100°C was studied as part of a program to recover a marketable iron product form metallurgical processing streams and effluents. Hematite was formed in preference to ferric oxyhydroxides (e.g. ß-FeO?OH) by controlling the precipitation conditions, especially by adding Fe2O3 seeds. The extent of the hydrolysis reaction was found to depend primarily on temperature and on the free-acid concentration. As to the latter, the controlled addition of an adsorbent of free acid, in our case the anionic resin polyvinylpyridine (PVP), was shown to allow for the nearly complete removal of iron as readily filterable Fe2O3. The hematite product typically contains = 63% Fe and = 1.5% Cl, and its composition does not change appreciably upon repeated cycling using regenerated PVP.

Jan 1, 2005

By J. D. Zhu, T. Ohmichi, H. Yasuda, S. Kashiwai, I. Ohnaka

"Since the casting process affects the properties of castings, its computer simulation has been greatly developed in the last decades. This paper presents our recent works, especially on mold filling simulation, because most casting defects such as porosities and inclusions that greatly affect the properties originate during mold filling. The first topic is the mold filling simulation with consideration of cavity pressure change during mold filling, including direct observation of flow phenomena with X-ray and pressure measurement. The second .one is the mold filling simulation in the lost foam process, in which gasification of polystyrene pattern and gas outflow through the coating and mold have been considered. The simulation can predict not only the mold filling sequences but also periodical vibration of the gas layer between the melt and pattern. The third one is the comparison of simulation of Al melt flow in a metallic runner and direct observation through a transparent mold, showing that the entrapped gas or inclusions is expelled ahead through the melt and its simulation needs very fine meshes. These examples show that the comparison of simulation and observation is very important to develop the numerical simulation further.IntroductionThe mechanical properties of castings are greatly affected by casting defects such as porosities and inclusions, and solidification structure. Although recently the structure simulation has greatly progressed [1-4 ], the application in plants is very limited, because the structure is mostly determined by chemical compositions and cooling rate, enabling us to estimate it from the structure of past similar castings without simulation.On the other hand, the casting defects often vary with each casting or time. Among the defects, porosities and inclusions are main causes to deteriorate the properties and mostly originate during mold filling. Therefore, a lot of efforts to simulate the mold filling and estimate those defects have been made in the last decades [l,5,6]. These efforts have been mostly to develop numerical techniques to solve the Navier-Stokes equation. However, the flow phenomena in molds have not been well understood, because the direct observation of the flow phenomena in mold is not easy. This means the accuracy of the simulation is still not clear."

Jan 1, 2000

By C. Cheung, U. Erb

"Over the past few years, nano-processing of magnetic materials has received considerable attention, because many magnetic and other application-specific properties have been shown to be enhanced in materials with ultrafine grain size. This paper reviews recent advances in the production of nano-processed soft magnetic materials such as pure nickel and cobalt as well as binary nickel-iron and ternary nickel-iron-chromium alloys by electrodeposition. Magnetic, electrical and mechanical properties of these materials are presented and discussed in terms of their microstructural defects.IntroductionIn recent years, nano-processing of materials to enhance their magnetic properties has received considerable attention [1-23]. Thin films, compositionally modulated thin films, granular films and bulk materials have been produced by many different techniques. These include gascondensation [1-6], ball-milling [7,8], chemical processing [9,10], metal-organo complex routes, solution reduction and co-precipitation [11], sol-gel methods [12], sputtering [12-14], rapid solidification [15], devitrification of amorphous alloys [16-19] and electrodeposition [12,20,21]. The potential application of nano-engineered materials with enhanced magnetic properties has been specifically discussed for soft magnets [18,19,22,23], hard permanent magnets [15] as well as for layered materials showing giant magnetoresistance effects [13,14] and nano-composites for magnetic refrigeration [11,12].The purpose of the present paper is to review recent advances in the development of nanocrystalline soft magnetic materials by electrodeposition methods. These materials could find applications in areas such as magnetic recording heads, high efficiency electric motors, transformer cores, etc."

Jan 1, 1994

By Fuming Wang, Lifu Hu, Changrong Li, Ruipeng Pang

The solidification structure of 430 ferritic stainless steel has been calculated in the solidification process by using 3D-CAFE model under the condition of water cooling. The calculated results consistent with those obtained from experiment. Under watercooling condition, the solidification structure consists of chilled layer, columnar grain zone, transition zone and equiaxed grain zone

Jan 1, 2015

By Bingyi Bai, Wangjun Peng, Yanling Guo, Jieyu Zhang, Guoding Gao

The phase transformation of bayan obo ore with high concentration of iron and calcium was reduced at temperatures no more than 1000℃ were investigated in this study. The samples with insufficient carbon were treated at the temperature using a vertical furnace with a thermogravimetry (TG). The mineral phases and content were examined using Xray diffraction (XRD) and X-ray fluorescence spectroscopy (XRF) respectively. The complex phases of bayan obo ore transformed to some simple phases after treated with different content of carbon at the same temperature for 10 hours. The result of XRD、 XRF and TG showed that the reduction degree of Fe3O4 phase formation varied with the temperature and the carbon content of bayan obo ore.

Jan 1, 2015

By Chikabumi Yamauchi, Mitsuru Tanahashi, Tsuyoshi Taniguchi, Nobuo Furuta, Toshiharu Fujisawa

"It is essential to clarify the equilibrium relations among nonmetallic inclusions of the Mn0-SiO2-CrOx system and molten stainless steel in order to control non-metallic inclusions formed by the deoxidation of stainless steel with silicon. In the present study, the phase equilibria of the MnO-SiO2-CrOx system were measured by conducting the following experiments under controlled oxygen partial pressure, Po2, at 1873 K:1) Phase equilibria of the MnO-Cr20 3 binary system were measured for Po2 = 2 x 10-6 ~2 x 102 Pa.2) Phase equilibria of the MnO-SiO2-CrOx ternary system were measured for Po2 = 2 X 10-6 Pa.Based on the results, the phase diagram of this ternary system was established under the condition of the Si-deoxidation process of stainless steel (Po2 = 2 x 10-6 Pa and T = 1873 K).IntroductionAt the deoxidation stage in steelmaking process, generally multiple deoxidizers participate in deoxidation reactions, and the composition of deoxidation products ""non-metallic inclusions"" greatly varies depending on deoxidizing efoments and their contents. In order to control non-metallic inclusions formed by the refining process of steel, it is essential to clarify the equilibrium relations among non-metallic inclusions and molten steel.Especially, during the refining process of stainless steel, nonmetallic inclusions in molten steel seem to- change as follows. After the oxidation refining, Mn-chromite is formed in molten steel as non-metallic inclusion. By the deoxidation with silicon addition (mainly less than 1 mass%), Mn-chromite inclusions are changed their compositions to Mn-silicate. Segawa et al.[l] have reported the effect of amount of silicon addition on composition and mass ratio· of non-metallic inclusions during the Sideoxidation process of 18Cr-8Ni stainless steel at 1873 K, as shown in Figuri; L At higher silicon content than 0.5 mass%, only Mn-silicate was identified as non-metallic inclusion. On the other hand, at lower silicon content, both of Mn-chromite (MnO Cr2O 3) and Mn-silicate were identified. However, the thermodynamic and the kinetic analyses of the above-mentioned Sicdeoxidation process have not been made due to lack in the thermodynamic data for the non-metallic inclusions· of the MnO-SiO2-CrOx system, such as the phase diagrams, the activities of the components, and the free energy of intermediate compounds. In relation to the phase diagram of this system, those of the MnO-SiO2 [2] and the SiO2-Cr2O 3 [3] binary systems have been only reported"

Jan 1, 2000

By Zhao wen Wang, Ramana G. Reddy, Min Li

"The electroreduction of Co(II) in l-butyl-3-methylimidazolium tetrafluoroborate (BMlMBF4) ionic liquid was investigated by cyclic volatrnmetry at 353 K. The results show that the reaction of Co(II) to Co is irreversible in one step with two electrons transferred. The diffusion coefficient of Co(II) was estimated to be 7.6 x 10-8 cm2 s·1 at 353 K. Then the electrodeposition of cobalt was studied at different cathodic potentials (-0.80 to -0.95 V) and different temperatures (333 to 363 K) in BMIMBF 4 containing 0.20 mol L-1 Co(BF4)z. The deposits were characterized using scanning electron microscope (SEM), energy-dispersive spectroscopy (EDS), and X-ray diffraction (XRD). SEM images show that a uniform, dense, and compact deposit was obtained at -0.80 V and 333 K. The deposits were identified as high-purity metallic Co for all experiments by EDS and XRD.IntroductionCobalt is known as a hard magnetic material and cobalt alloys have been shown to have excellent magnetic properties with adequate mechanical durability and corrosion resistance, which are needed for high performance magnetic recording applications [1-4]. The electrodeposition of Co alloy in the aqueous solution is generally difficult because of the narrow electrochemical potential window of water, which leads to the low current efficiency and worse quality of deposits due to the hydrogen embrittlement. Thus, aprotic ionic liquids (ILs) are expected to be the ideal alternative media for electrodeposition of cobalt or its alloy since ILs usually provide a wide working potential windows, negligible vapor pressure, and acceptable conductivity for electrolysis without the occurring of hydrogen evolution [5, 6]."

Jan 1, 2014

By N. Ono, H. Fujiwara, S. Otsuka-Yao-Matsuo, T. Omata

"The electrical conductivity and the oxygen release and uptake of sintered indium tin oxide (ITO) upon heating and cooling under the condition that P(O2)/P*=4.9X10-4 (P* = atmospheric pressure), :when P(O2) was approximately 50Pa, were simultaneously measured by using a closed-system oxygen-gas analyzer. A large increasing in -the electrical conductivity - upon the· oxygen release detected in 1130<T<1273K was observed. Quantitative relationship between the number of oxygen atom released from ITO and the conduction electron density in ITO was studied. The release of one oxygen atom agreed with the generation of two conduction electrons, i.e., the efficiency-carrier-generation for the oxygen release from the ITO was almost one. The oxygen atom released must be originally at the quasi-anion site in the C-type rare-earth lattice, i.e., the 16c site in the space group of Ia3, as an interstitial excess oxygen, Oi"". It was concluded that the mechanism of conduction carrier generation and compensation upon SnO2 doping into In2O3 can be expressed by the defect equation, 2SnO2-2Sn1n +2(1-z)e'+zOi""+3O0 x+(l-z)/2O2, and that the oxygen release bringing the increase in the electrical · conductivity can be expressed by the equation, Oi""-1/2O2+2e'.IntroductionThin films of SnO2-doped In2O 3 (generally designated as ITO, for indium tin oxide), which have high optical transparency for visible light and high electrical conductivity, have been used as transparent electrodes for liquid crystal and electrochromic displays. It is well known that the electrical conductivity of ITO depends on the content of SnOi-dopant and oxygen. However, a reliable relationship between electrical conductivity and the absolute oxygen content in ITO has yet to be reported. The elucidation of such a relationship is one of the important clues for realizing extremely highly conductive ITO electrodes."

Jan 1, 2000

By Shigehito Deki

"A new wet process has been developed for the synthesis of various kinds of oxide thin films on various kinds of substrates, even which have complex surface morphology, from aqueous solution. The process was named as the LPD, Liquid Phase Deposition, method, which has some advantages over the conventional dry processes. This process can be applied to an on-site synthesis of advanced materials in the thin film technology. In this paper, some current topics on the synthesis of the composite thin oxide films by the LPD method, are presented.IntroductionGenerally, metal oxide thin films have been made by different preparative processes such as r.f. sputtering, chemical vapor depositon, CVD, laser ablation and sol-gel method, etc [1-3]. Each method has it own advantages and disadvantage. In some cases, the process is not suitable for the preparation of thin film on substrate with large surface area or complex surface morphology, and makes the deposition apparatus complicated and expenisve. By using Liquid Phase Deposition, LPD, method which overcomes some of those problems, metal oxide or hydroxide thin film can be formed on the substrate with large surface area and complex surface morphology, which are immersed into the aqueous solution only at ambient temperature and under atmosphere without any special equipments and high energy. And also, multicomponent oxide thin films can be formed readily by mixing solutions containing the objective metal ions, because it is performed in the aqueous solution which is typically a homogeneous mixing system. This process utilizes ligand-exchange, hydrolysis, equlibrium reaction of metal-fluoro complex species, MF x (x-2n>-, and F consumptive reaction. In the aqueous solution, MFx<x-2n>-is hydrolyzed with water to release F ions by a ligand exchange equilibrium reaction as following;"

Jan 1, 2000

By M. Krishna, Jayagopal Uchi1, Shanta Sastry, B. M. Satish

"A well-considered composite of ZA-27 reinforced with weight percentage 0, 2, 4, and 6% of alwninite particulate has been made by compocasting technique. The elastic properties of ZA- 27 /alwniniute particulate composite were determined by using U1M. The results showed that the modulus of elasticity and UTS of the composite gradually increases with increase in the wt.% of reinforcement. However, the overall ductility decreased monotonically with an increase in reinforcement. The results of these tests· as well as the predictions of several model~ for composite strengthening available in the literature were compared with experimental results. The data observed from Young's modulus by measurements studies were compared with theoretical results predicted by Eshelby model.IntroductionMetal matrix composites (MMCs) have received increasing attention in _the recent decades as engineering materials. The introduction of a ceramic reinforcement into a metal matrix produces a composite material resulting in an attractive combination of physical and mechanical properties that cannot be obtained with monolithic alloys. Particulate reinf9rced MMCs among the discontinuously reinforced MMCs have attracted quite a lot of attention both in the industrial sectors and the academic communities. There is an increasing need for knowledge about the processing techniques and mechanical behavior of particulate MMCs in view of their production getting enhanced and their commercial applications becoming wider [I]. Interest in particulate reinforced MMCs is mainly due to easy availability of particles and economical processing techniqu"

Jan 1, 2000

By Drew Sinha

Success of the environmentally benign semiconductor manufacturing depends on the cost-effective integration of the principles of reduce, recover, reuse and recycle from source material to final product disposal. Increasing demand combined with current shortage of polysilicon provided unique opportunities to recover the silicon waste, caused by various defects, in wafer manufacturing process. Current practices relating to recovery and reuse of waste silicon produced, from crystal growth process to finally polished and epitaxially deposited silicon wafer, at Mitsubishi Silicon America is presented. Future plan to recycle the process generated silicon fines produced during the intermediate steps of the wafer manufacturing process such as grinding, slicing, lapping and polishing is also discussed.

Jan 1, 1998

By Nagy El-Kaddah, T. T. Natarajan

This paper describes a novel approach for modeling three-dimensional electromagnetically driven flow in inductively stirred systems, and its application to modeling electromagnetic and flow phenomena in sub-mold rotary stirring of billets. It is based on a new T-\jf potential formulation of electromagnetic field, which does not require the calculation of the field in free space. A finite element algorithm has been developed for solving the electromagnetic field and Navier-Stokes equations in the fluid flow domain. The computed results have shown that the electromagnetic force field generates a strong rotational flow within the vertical section covered by the stirrer, and a relatively strong secondary flow beyond the stirrer. It has also been shown that the rotational and secondary flows were driven primarily by the vorticity of the force field at the billet corners. The induced flow in the molten pool was found to be turbulent and the effective mixing region in the molten pool was about three times the length of the stirrer. The mathematical approach presented in this paper provides the theoretical framework for quantifying these effects for any given stirrer configuration and operating parameters.

Jan 1, 1999

By Liangju He, Peixuan Ouyang, Peijie Li

Single-pulse laser ablation of aluminum and titanium alloys under glass confinement is investigated. Processing parameters such as laser intensity and gap width between targets and glass are varied. Surface morphologies and crater profiles of the alloys after laser ablation are studied by SEM and white-light interferometric microscope, respectively. The effects of gap width and laser intensity on surface morphologies and crater profiles of targets are systematically analyzed. In addition, the generation of porous surface structures in Ti target is regarded as the result of phase explosion in the molten surface layer of targets and the thermodynamic condition in our experiment for phase explosion is evaluated.

Jan 1, 2016