Search Documents

By S. Prasad

The effectiveness of ultrasonic velocity measurements and attenuation of the propagating pulse was evaluated as a means of Non-Destructive characterization of cold worked and annealed copper. Commercial copper is subjected to mechanical working such as forging, rolling and thermal treatment to induce re-crystallization. The microstructural changes that occur in copper and a variation in its mechanical properties are subjected to analysis using the ultrasonic technique. The signal processing is carried out using the wavelet analysis technique. The features of wavelet analysis namely, localization in space and the presence of an infinite set of basis functions allows removing noise from the time series and components of a non-stationary signal to be analyzed. This is seen to improve the accuracy of the results obtained from the ultrasonic technique in the case of copper, which has distinct coarse grains that are difficult to inspect due to backscattering from the grain boundaries.

Jan 1, 2010

By Wenming Wang

Recycling of retired cadmium telluride (CdTe) photovoltaic (PV) modules has attracted attention due to new European environmental regulations. Recycling tellurium from CdTe PV modules is becoming more important because of the low availability of this metal. We investigated several treatment paths for reclaiming tellurium from solutions obtained from leaching fragments of CdTe PV modules. Our experiments showed that conventional soda ash neutralization/hydrolysis methods recovered only 50~60% of tellurium. However, by appropriately combining neutralization and sulfide precipitation, almost all the tellurium present in the leaching solution was precipitated and recovered; the concentration of tellurium in the processed solution was reduced from 900-1000 mg/L to less than 1 mg/L, yielding a tellurium recovery greater than 99%. This method can be incorporated in the scheme of recycling spent CdTe PV modules and manufacturing wastes. It may be also an alternative to the current operations for removing tellurium from copper anode slime leaching solutions.

Jan 1, 2006

By Dachun Liu, Wenlong Jiang, Guozheng Zha, Liang Hu

In this paper, a novel technique for recovery of gallium and arsenic by thermal decomposition under vacuum is presented. The effects of distillation tem- perature on the volatilization behavior of each component were investigated. Theoretical calculations and experimental studies have shown that the method is feasible. The results show that under optimum conditions, highly pure Ga can be extractedwithadvantagesoverconventionaltechniques,includingsimpleoperation andenvironmentalfriendliness.Forexample,metallicgallium(purity > 99.99%)is obtained at 1273 K after 3 h under 3–8 Pa. Arsenic is obtained in the form of a elementary substance which could be preserved with relative ease. (cid:1) (cid:1)

Mar 1, 2018

By Deming Wang, R. A. Overfelt

"The oscillating cup viscometer has become a dominant technique to measure the viscosities of high temperature molten metals. Unfortunately, the viscosity estimation model from the observed logarithmic decrement and period of the oscillation is very complicated. There are still large discrepancies of viscosity estimation values between using different measurement facilities and using different viscosity estimation models for a same molten metal. The purpose of the paper is to evaluate the accuracy of an oscillating cup viscometer in Auburn University. Two well known viscosity estimation models, Roscoe's and Torklep's equations, are compared and discussed. The theoretical literature for the fluid flow inside an oscillating cup is reviewed and a more accurate working equation for the Auburn oscillating cup viscometer is developed. Some design parameters of the oscillating cup viscometer, which directly affect the accuracy of viscosity estimation by using the working equation, are discussed. In addition, applications and experimental measuring data are presented in the paper for several different commercial alloys, such as aluminum alloys: A319, A356 and A201, nickel-base super alloys: In713 and In718, and casting irons, C40 Gray Iron and Ductile Iron.1 IntroductionThe oscillating cup viscometer is the most important and has been most frequently used in viscosity measurement for high temperature liquids [1-4]. The principal advantages of this technique over others are its mechanical simplicity and the ability to measure the time period and amplitude decay with great precision. In the viscometer, a high temperature liquid (such as a molten metal) is contained within a crucible suspended by a wire to form a torsional pendulum, which induces torsional oscillation motion. This motion is damped primarily by viscous dissipation within the viscous liquid inside the cup. The viscosity of the liquid can be calculated by an analytical or numerical solution ofthe equations of motion of the oscillating cup system."

Jan 1, 2001

By B. J. Zhao, F. L. Han, L. E. Wu, M. Chen, Y. H. Chen

Magnesium is the lightest structural metal with a density only two-thirds of aluminium and one-quarter of steel. It can be produced by electrolysis of fused magnesium chloride or high temperature reduction of the oxide. The predominant method for magnesium production is the Pidgeon process which is a batch process starting from calcined dolomite and ferrosilicon. CaF2 is commonly used in the process as the catalyst. Analyses of the slag samples and thermodynamic calculations indicated that liquid phase plays important role in the reduction process. Effects of chemistry, temperature and gas pressure on the production have been discussed and compared with the operating data. Understanding of the reaction mechanisms will provide a fundamental base for alternative processes of the magnesium production.

Mar 1, 2017

By E. Fockedey

he destruction of free cyanide on a Co3O4 doped carbon felt was studied. The experiments were done with an eiectrochemical filter press cell on dilute alkaline solutions containing 250 mg/l NaCN. No chloride ions were added to the solutions. The cobalt oxide protects the felt against corrosion and has a catalytic effect on the degradation of the cyanide. This kind of electrode allows working with current density as high as 1200 Aim without any visible degradation of the felt. The most interesting results were obtained with a current density of 400 Aim' at which the cyanide concentration can be lowered to 5 mg/l with a current efficiency of more than 70 % and a specific energy consumption of about 10 kWh/ kg CN.

Jan 1, 1998

By C. Schwandt

Recent research work has led to the development of a new electrochemical hydrogen sensor, which is based on a proton conducting solid electrolyte in conjunction with a self-contained solid hydrogen reference standard and is operated at elevated temperatures. The incorporation of the internal hydrogen reference renders the sensor versatile and user-friendly and makes it attractive for practical exploitation. The present article focuses on the utilisation of the sensor as the integral part of a probe for the quantitative determination of hydrogen in molten aluminium and aluminium alloys. The main features of the sensor and the probe as well as the measuring technique are discussed. Experimental results obtained with the novel analyser in trials under industrial conditions are presented and highlight the good performance of the device.

Jan 1, 2003

By H. Fukuyama

The wetting behavior of single crystalline MgO by fayalite-type slag melts has been studied by the sessile drop technique incorporated with high temperature X-ray radiography. The experiments were performed under oxygen partial pressures of 10-6 and 10-4 Pa at 1473 K. Mass ratios of iron to silica, Fe/Si~, in the slag employed were 1.4 and 2.0. To investigate the interfacial reaction, experiments using high density MgO crucibles were also conducted. The reactions at the interfaces were examined by Electron Probe Microanalysis. The contact angles between the slag melts and the MgO substrates were found to be relatively low, ranging from 30 to 10 degrees. The surface tension of the slag was 0.4 N/m for a slag of Fe/Si02 = 2.0. Two phases, magnesiowiistite and olivine, were observed at the interface. Interdiffusivity in magnesiowiistite solid solution was determined as a function of iron oxide content. Phase relations between magnesiowilstite and olivine, and the growth rates of both phases, are also discussed

Jan 1, 1996

By K. G. Wang, M. E. Glicksman, P. Crawford

"We formulate the mathematical solution to late-stage multi particle diffusion in finite systems. The transition from finite system behavior to that for an infinite system is established. Large-scale simulations are reported regarding the dynamics of phase coarsening. Even in the case of a small volume fraction (Vv = 10-4), the particle size distribution is broader than that for the well-known Lifshitz-Slyozov limit at zero volume fraction. We also report the first simulation studies of extremely low volume fraction, for which corresponding experiments, as well as other simulations, do not exist at present for comparison. However, in the case of moderate volume fractions (Vv = 0.1), the fiucutations in the volumetric growth rate of particles are extracted from our simulations. These simulations provide additional insight into the statistical nature of diffusion interactions, including multiparticle stochastics during microstructural evolution.IntroductionPredicting microstructure evolution in alloys remains one of the cornerstones of materials science. Phase coarsening is a common process in microstrucural evolution that leads to a decrease in the excess total interfacial energy of the system. The system typically consists of separate and identifiable units, or domains, such as second-phase particles distributed in a matrix. During phase coarsening, larger particles grow at the expense of small particles. Over time, this ""competition"" results in an increase in the average size of the particle population, and in a concomitant decrease in the number of particles.Particle size and microstructure of many cast alloys depend on similar coarsening processes. Indeed, properties of these materials, such as strength, toughness, ductility, and electrical conductivity, depend on the material's average particle size and particle size distribution (PSD). Understanding and controlling microstructures in two-phase systems are clearly of widespread technological importance."

Jan 1, 2001

By K. Osseo-Asare

It is possible to form a two-phase system in certain polymerlinorganic salt/water mixtures, such as those containing the polymer polyethylene glycol (PEG). Such aqueous biphase systems have many of the separation characteristics of conventional solvent? extraction systems, but are environmentally friendlier. Just like the well-known organic solvent/water two-phase system, the top polymer-rich phase is more hydrophobic. and the bottom salt-rich phase more hydrophilic. The partition of dispersed? particles is dependent on the interfacial interaction between the particles and the conjugate aqueous biphase solutions. In particular, the hydrophilic/hydrophobic properties of the surface determine the transfer of the dispersed particles into either the top (more hydrophilic) phase or the bottom (more hydrophobic) phase. Accordingly, differences in the surface chemistry of particles can be exploited to achieve selective separations. In this work, several approaches to separation control will be discussed. using pyrite (FeS2), alumina (AI203). hematite (Fe203), silica (Si02), and titania (Ti02) as model particulate materials. For metal sulfides, pH and redox potential can be used to alter the hydrophobicity/hydrophilicity of the particles. In ?the case of oxides. polymer adsorption and collector adsorption may be exploited to facilitate particle transfer.

Jan 1, 1999

By Hui-gang Wang, Mei Zhang, Min Guo

Metal-doped Ni–Zn ferrite with spinel structure was directly synthesized from treated zinc-containing electric arc furnace dust (Zn-containing EAFD) by solid state reaction method, realizing the transformation of Zn-containing EAFD from solid waste to high value-added material. A certain mass of NiCl26H2O was added to the treated Zn-containing EAFD before calcination. Then the effects of the mass ratio of treated Zn-containing EAFD to NiCl26H2O (RTZE/N, g g−1) and calcination temperature on the synthesis and magnetic properties of as-synthesized samples were systematically investigated by X-ray Diffraction, Raman Spectroscopy and Physical Property Measurement System. It is indicated that RTZE/N and calcination temperature had important influences on the synthesis of single-phase spinel ferrite and their magnetic properties. Pure metal-doped Ni–Zn ferrite, which exhibited good magnetic properties of higher saturation magnetization (Ms, 60.5 emu g−1) and lower coercivity (Hc, 49.8 Oe), was obtained when the calcination temperature was controlled at 1100 °C for 2 h with RTZE/N of 1:0.9.

Mar 1, 2017

By Slobodan Radosavljevic

The polymetallic W-Pb-Bi-Ag ore from the ?Nova jama? ore zone of the Rudnik ore field have been investigated. Contact-pneumatolytic (skarn), pneumatolytic-hydrothermal, and hydrothermal mineralization phases are defined in this ore zone. The most significant mineralization phase that gave compact ore bodies is pneumatolytic-hydrothermal phase. A relatively pure Mo-free scheelite is the only tungsten-bearing mineral. Lead minerals are mostly presented by Pb-Bi sulphosalts and much less with galena. The image analysis coupled with Energy Dispersive Spectrometry (EDS) analysis on a Scanning Electron Microscope (SEM) was applied to the characterization of a W-Pb-Bi-Ag ore as an efficient tool for mineral quantification. Results of EDS (Energy Dispersive Spectrometry) analyses gave the empirical formulae: Pb1.91Ag0.05Cu0.08Bi1.93S5 for cosalite, Pb0.98Ag0.03Cu0.05Bi1.99S4 for galenobismutite and galena Pb0.99Ag0.03S.

Jan 1, 2006

By Stavros A. Argyropoulos, Henry H. Hu

"The assimilation of exothermic additions in liquid metals exhibit an array of unique coupled heat, mass and momentum transport phenomena. These phenomena are further complicated by the presence of a moving boundary.This paper describes a) A mathematical model which simulates the complex phenomena, and b) An extensive verification of the mathematical model. The SIMPLER algorithm was employed to solve numerically the pertinent partial differential equations. The computational results indicated that the exothermic heat of mixing led to a rapid increase in temperature around the moving boundary, which produced an enhanced convective flow in the liquid phase. The intensification of fluid flow around the moving boundary resulted in an acceleration of the melting process.Verification of the model was carried out in two contexts. The first was, in a low temperature physical model consisting of ice immersion in different sulfuric acid solutions. In this physical model, both temperature and velocity measurements were carried out. The model results were compared with experimental measurements and they were found to be in excellent agreement. The second context employed high temperatures, involving the assimilation of silicon in high carbon liquid iron. The model was also applied to predict fluid flow, heat and mass transfer for these high temperature experiments and a good agreement was obtained.In addition new dimensionless heat transfer correlations that quantify these complex phenomena will be presented."

Jan 1, 2001

By Peter G. Cooper

"During 1987, the feasibility of modernising the ER&S smelter at Port Kembla, NSW, Australia was studied. The selection of appropriate technologies to carry the smelter into the 21st century considered issues such as capital cost, existing infrastructure, feed mix, capacity, product quality, flexibility and potential for further development. Both hydrometallurgical and pyrometallurgical process schemes were considered. Some novel combinations were assessed but ultimately rejected. Final technology selections included proven smelting and anode furnace processes, pyrometallurgical slag cleaning and modifications to existing equipment. This process scheme balanced risk against development potential within the constraints imposed by the existing plant.BackgroundThe Electrolytic Refining and Smelting Company of Australia (ER&S) has operated a custom copper smelter at Port Kembla since 1908. Existing technology includes a sinter plant/blast furnace, three small Peirce Smith converters, two reverberatory anode furnaces and a conventional tankhouse. These process units were all installed prior to 1960 and have proven to be flexible enough to process the wide variety of domestic feed materials purchased by ER&S.However, by the early 1980s, threats to domestic concentrate supplies highlighted the need for major changes to reduce operating costs to world competitive levels. Various studies in the ensuing years failed to identify an economically attractive solution. Furthermore, pressures were increasing to improve the environmental performance of the smelter.During 1986 the options for redevelopment were again considered and by the end of 1987 technologies for the retrofit had been selected and a full feasibility study was completed."

Jan 1, 1988

By M. L. Cunha

The lack of control of As and Sb compounds from copper smelters and converters has rendered some chalcopyrite containing arsenopyrite, stibnite and tetrahedrite minerals unusable for metal extraction. In the present investigation, we have studied the carbothennic reduction of Portuguese chalcopyrite mineral concentrate in the presence of lime/CaS04 and CaS04/Si02. Thermodynamic equilibrium calculations were performed to study the distribution of As and Sb between metal and the CaO-Si02-FeO slag phase. The phase equilibrium calculations also show the effect of oxygen partial pressure on the increase in the volume of the slag phase, which helps in lowering the copper metal formation temperature and facilitates a better separation between metal, matte and slag. The reduction reaction kinetics was studied between 850°C and 1100 °C, and the phases formed were identified by X-ray powder diffraction and scanning electron microscopy techniques. The importance of this research for using recycled matte, lean and rich minerals with As and Sb is also explained.

Jan 1, 2001

By Frederic Pineau

Semisolid metal alloys have a special microstructure of globular grains suspended in a liquid metal matrix. This particular physical state of the matter can be exploited to produce near-net- shape parts with improved mechanical properties. However, the behavior of the slurry is strongly influenced by the local solid fraction and state of agglomeration. Different flow instabilities ·associated with the combined flow and solidification process result, which make difficult the application of semi-solid processing in the casting industry. Moreover, the rheology of semisolid materials is not well understood. Most of the theory has been derived from experimental data, which are somewhat difficult to measure. A model that accounts for the multiphase nature of semisolid slurries is required to get more insight into such complex flows. This paper describes a mixture model for semisolid slurries. It assumes that the mixture of liquid-solid components behaves as a single fluid as far as overall mass and momentum balances are concerned. The coupling force between the phases is derived on the assumption that the slurry is a fluid saturated isotropic media. The proposed methodology is implemented in a finite element code. The model is then applied to the the filling of an industrial-scale capillary flow viscometer. Segregation patterns are obtained and discussed.

Jan 1, 2001

By Alicia Esther Ares

The family of Zn-Al (ZA), Zn-Ag and Zn-Al-Ag (ZINAG) alloys offers high mechanical properties, ease of finishing, the advantage of low energy and pollution-free melting. Also, present alternatives to the well developed alloy systems, such as brasses, bronzes, cast irons and aluminum alloys. The main objective of this paper is to measure thermal parameters in ZA, Zn-Ag and ZINAG hypoeutectic and hypereutectic alloys directionally solidified which present columnar, equiaxed and columnar to equiaxed transition structures (CET). Also, estimate the mechanical properties, such as microhardness and tensile parameters and correlate these with the thermal (cooling rate) and structural parameters (grain size and dendritic spacing). The different types of structures were analyzed with optical and scanning electron microscopy. The results showed the influence of concentration, microstructural arrangement and thermal conditions during solidification on the mechanical properties. The results of the present investigation are compared with previous experiments.

Jan 1, 2010

By Rafael Padilla

In the production of copper from chalcopyrite (CuFeS2) concentrates by the smelting and converting technology, the ambient pollution with gaseous S02 and toxic metals such as arsenic compounds is still a serious problem, especial1y in the converting step due to the batch nature of the conventional Peirce Smith process. Non-SO2 emitting alternatives are leaching processes. However, few of them have had a limited industrial application and they are not very effective in discarding safely the toxic impurities. A combination of pyro-hydrometal1urgical methods: the sulfidation of chalcopyrite and subsequent leaching of the sulfidized material is a non-polluting alternative to treat not only clean chalcopyrite concentrates but also complex chalcopyrite-enargite concentrates. In this article, this alternative is discussed concerning the thermodynamics and kinetics of the sulfidation of chalcopyrite with gaseous sulfur. The kinetics of the leaching of the sulfidized concentrate in an H2SO4-NaCI-O2 system is also discussed.

Jan 1, 2003

By David Arana

The use of gas-water dispersion of a molten material flow onto a vibrating surface is developed as a process to minimize water pumping requirements, minimize the risks of explosions, and minimize the post solidification dewatering and fines handling equipment requirements. The process uses existing vibration transport technologies and common plant utilities. Plant trials using the smaller footprint and the progressive molten particle cooling time have yielded encouraging results. The results are analyzed and reported.

Jan 1, 2006

By Xiaobing Yang, Animesh Jha, Greg Doughty

"Successful use of inert anodes should reduce the CO2 footprint in aluminum production. The search for a “holy grail” inert anode for metal electro-winning from constituent oxides using molten salt bath as an electrolytic medium is continuing. In this article we demonstrate the engineering approaches for the fabrication of intermetallic anodes, based on a quaternary Al-Ti-Cu-M (M:Ni, Fe) system for primary aluminium production. In particular, we examine the microstructural and electrochemical properties of alloys, based on the quaternary compositions. We explain the aspects of phase stability under anodic potential, which leads to the loss of anodic materials in the temperature range of 850-1050oC. The results are analysed in the context of oxidation reaction and formation of oxide layers which readily dissolve in the cryolite melt and prevent passivation. The paper also describes the conditions under which the reduction of aluminium at the graphite cathode occurs which also strongly depends on the molten salt chemistry for the nucleation of molten aluminium at the cathode.1. IntroductionOxygen-evolving inert anodes are an alternative to the conventional consumable carbon anodes for the production of primary aluminium. In this paper the materials selection criteria chosen for the engineering of anode is based on the understanding of the thermodynamic stabilities of aluminide intermetallic phases, some of which are formed and remained stable in fluoride melts. For example, the formation Al3Ti dispersed in aluminium metal via molten-fluoride flux reaction is well known in the context of aluminium casting and grain refining [1-3]. It is for this reason in our research we concentrated on the engineering of stable intermetallic phase mixture in the Al-Ti-Cu ternary system, shown in Figure 1 [4]. In this figure two compositions in the Al3-0.5zTi1-0.5zCuz family are shown with the substitution of 7 atomic % and 11 atomic % copper. However initial investigations showed that these two compositions were unsuitable due to the formation of low-temperature liquid (~540oC) and intermetallic phase, Al2Cu along the Al-Cu binary edge during solidification. The Al2Cu phase segregated along the boundaries of Al3Ti and Al5Ti2Cu, and dissolved away when electrolysis was carried out using these anodes above 800oC. The presence of consequential porosity in the anode material increased the corrosion of the alloy through local heating due to high current density at 0.8 A cm-2. The early tests were carried out with cryolite melts, shown in Figure 2, having 3 weight percent of Al2O3 in the bath at 850oC."

Jan 1, 2010